[ Upstream commit 71b12beaf1 ]
According to Asus firmware engineers, the meaning of these codes is only
to notify the OS that the screen brightness has been turned on/off by
the EC. This does not match the meaning of KEY_DISPLAYTOGGLE /
KEY_DISPLAY_OFF, where userspace is expected to change the display
brightness.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3f2f3799a ]
When the OS registers to handle events from the display off hotkey the
EC will send a notification with 0x35 for every key press, independent
of the backlight state.
The behavior of this key on Windows, with the ATKACPI driver from Asus
installed, is turning off the backlight of all connected displays with a
fading effect, and any cursor input or key press turning the backlight
back on. The key press or cursor input that wakes up the display is also
passed through to the application under the cursor or under focus.
The key that matches this behavior the closest is KEY_SCREENLOCK.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8fac5cbdfe upstream.
The hyp-stub is loaded by the kernel's early startup code at EL2
during boot, before KVM takes ownership later. The hyp-stub's
text is part of the regular kernel text, meaning it can be kprobed.
A breakpoint in the hyp-stub causes the CPU to spin in el2_sync_invalid.
Add it to the __hyp_text.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65dbb423cf upstream.
Originally, cns3xxx used its own functions for mapping, reading and
writing config registers.
Commit 802b7c06ad ("ARM: cns3xxx: Convert PCI to use generic config
accessors") removed the internal PCI config write function in favor of
the generic one:
cns3xxx_pci_write_config() --> pci_generic_config_write()
cns3xxx_pci_write_config() expected aligned addresses, being produced by
cns3xxx_pci_map_bus() while the generic one pci_generic_config_write()
actually expects the real address as both the function and hardware are
capable of byte-aligned writes.
This currently leads to pci_generic_config_write() writing to the wrong
registers.
For instance, upon ath9k module loading:
- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER,
located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C
(CACHE_LINE_SIZE)
Fix the bug by removing the alignment in the cns3xxx mapping function.
Fixes: 802b7c06ad ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org # v4.0+
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1dbd449c99 upstream.
The nr_dentry_unused per-cpu counter tracks dentries in both the LRU
lists and the shrink lists where the DCACHE_LRU_LIST bit is set.
The shrink_dcache_sb() function moves dentries from the LRU list to a
shrink list and subtracts the dentry count from nr_dentry_unused. This
is incorrect as the nr_dentry_unused count will also be decremented in
shrink_dentry_list() via d_shrink_del().
To fix this double decrement, the decrement in the shrink_dcache_sb()
function is taken out.
Fixes: 4e717f5c10 ("list_lru: remove special case function list_lru_dispose_all."
Cc: stable@kernel.org
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4522a70db7 ]
Use pskb_may_pull() to make sure the optional fields are in skb linear
parts, so we can safely read them later.
It's easy to reproduce the issue with a net driver that supports paged
skb data. Just create a L2TPv3 over IP tunnel and then generates some
network traffic.
Once reproduced, rx err in /sys/kernel/debug/l2tp/tunnels will increase.
Changes in v4:
1. s/l2tp_v3_pull_opt/l2tp_v3_ensure_opt_in_linear/
2. s/tunnel->version != L2TP_HDR_VER_2/tunnel->version == L2TP_HDR_VER_3/
3. Add 'Fixes' in commit messages.
Changes in v3:
1. To keep consistency, move the code out of l2tp_recv_common.
2. Use "net" instead of "net-next", since this is a bug fix.
Changes in v2:
1. Only fix L2TPv3 to make code simple.
To fix both L2TPv3 and L2TPv2, we'd better refactor l2tp_recv_common.
It's complicated to do so.
2. Reloading pointers after pskb_may_pull
Fixes: f7faffa3ff ("l2tp: Add L2TPv3 protocol support")
Fixes: 0d76751fad ("l2tp: Add L2TPv3 IP encapsulation (no UDP) support")
Fixes: a32e0eec70 ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6")
Signed-off-by: Jacob Wen <jian.w.wen@oracle.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62e7b6a57c upstream.
Remove l2specific_len dependency while building l2tpv3 header or
parsing the received frame since default L2-Specific Sublayer is
always four bytes long and we don't need to rely on a user supplied
value.
Moreover in l2tp netlink code there are no sanity checks to
enforce the relation between l2specific_len and l2specific_type,
so sending a malformed netlink message is possible to set
l2specific_type to L2TP_L2SPECTYPE_DEFAULT (or even
L2TP_L2SPECTYPE_NONE) and set l2specific_len to a value greater than
4 leaking memory on the wire and sending corrupted frames.
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e15aa3b2b1 ]
After a timeout event caused by for example a broadcast storm, when
the MAC and PHY are reset, the BQL TX queue needs to be reset as
well. Otherwise, the device will exhibit severe performance issues
even after the storm has ended.
Co-authored-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: Mathias Thore <mathias.thore@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0cf029234 ]
When an internally generated frame is handled by rose_xmit(),
rose_route_frame() is called:
if (!rose_route_frame(skb, NULL)) {
dev_kfree_skb(skb);
stats->tx_errors++;
return NETDEV_TX_OK;
}
We have the same code sequence in Net/Rom where an internally generated
frame is handled by nr_xmit() calling nr_route_frame(skb, NULL).
However, in this function NULL argument is tested while it is not in
rose_route_frame().
Then kernel panic occurs later on when calling ax25cmp() with a NULL
ax25_cb argument as reported many times and recently with syzbot.
We need to test if ax25 is NULL before using it.
Testing:
Built kernel with CONFIG_ROSE=y.
Signed-off-by: Bernard Pidoux <f6bvp@free.fr>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: syzbot+1a2c456a1ea08fa5b5f7@syzkaller.appspotmail.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Bernard Pidoux <f6bvp@free.fr>
Cc: linux-hams@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a40ded6043 ]
Driver reads the query HCA capabilities without the corresponding masks.
Without the correct masks, the base addresses of the queues are
unaligned. In addition some reserved bits were wrongly read. Using the
correct masks, ensures alignment of the base addresses and allows future
firmware versions safe use of the reserved bits.
Fixes: ab9c17a009 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Fixes: 0ff1fb654b ("{NET, IB}/mlx4: Add device managed flow steering firmware API")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91c524708d ]
The size of L2TPv2 header with all optional fields is 14 bytes.
l2tp_udp_recv_core only moves 10 bytes to the linear part of a
skb. This may lead to l2tp_recv_common read data outside of a skb.
This patch make sure that there is at least 14 bytes in the linear
part of a skb to meet the maximum need of l2tp_udp_recv_core and
l2tp_recv_common. The minimum size of both PPP HDLC-like frame and
Ethernet frame is larger than 14 bytes, so we are safe to do so.
Also remove L2TP_HDR_SIZE_NOSEQ, it is unused now.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Suggested-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Jacob Wen <jian.w.wen@oracle.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5ee066333 ]
IPv6 does not consider if the socket is bound to a device when binding
to an address. The result is that a socket can be bound to eth0 and then
bound to the address of eth1. If the device is a VRF, the result is that
a socket can only be bound to an address in the default VRF.
Resolve by considering the device if sk_bound_dev_if is set.
This problem exists from the beginning of git history.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bug has been discovered when redirecting splice output to regular files
on EXT4 and tmpfs. Other filesystems might be affected.
This commit fixes the issue for stable series kernel, using one of the
change introduced during the rewrite and refactoring of vfs_iter_write in
4.13, specifically in the
commit abbb65899a ("fs: implement vfs_iter_write using do_iter_write").
This issue affects v4.4 and v4.9 stable series of kernels.
Without this fix for v4.4 and v4.9 stable, the following upstream commits
(and their dependencies would need to be backported):
* commit abbb65899a ("fs: implement vfs_iter_write using do_iter_write")
* commit 18e9710ee5 ("fs: implement vfs_iter_read using do_iter_read")
* commit edab5fe38c
("fs: move more code into do_iter_read/do_iter_write")
* commit 19c735868d ("fs: remove __do_readv_writev")
* commit 26c87fb7d1 ("fs: remove do_compat_readv_writev")
* commit 251b42a1dc ("fs: remove do_readv_writev")
as well as the following dependencies:
* commit bb7462b6fd
("vfs: use helpers for calling f_op->{read,write}_iter()")
* commit 0f78d06ac1
("vfs: pass type instead of fn to do_{loop,iter}_readv_writev()")
* commit 7687a7a443
("vfs: extract common parts of {compat_,}do_readv_writev()")
In order to reduce the changes, this commit uses only the part of
commit abbb65899a ("fs: implement vfs_iter_write using do_iter_write")
that fixes the issue.
This issue and the reproducer can be found on
https://bugzilla.kernel.org/show_bug.cgi?id=85381
Reported-by: Richard Li <richardpku@gmail.com>
Reported-by: Chad Miller <millchad@amazon.com>
Reviewed-by: Stefan Nuernberger <snu@amazon.de>
Reviewed-by: Frank Becker <becke@amazon.de>
Signed-off-by: Jimmy Durand Wesolowski <jdw@amazon.de>
commit 60f1bf29c0 upstream.
When calling smp_call_ipl_cpu() from the IPL CPU, we will try to read
from pcpu_devices->lowcore. However, due to prefixing, that will result
in reading from absolute address 0 on that CPU. We have to go via the
actual lowcore instead.
This means that right now, we will read lc->nodat_stack == 0 and
therfore work on a very wrong stack.
This BUG essentially broke rebooting under QEMU TCG (which will report
a low address protection exception). And checking under KVM, it is
also broken under KVM. With 1 VCPU it can be easily triggered.
:/# echo 1 > /proc/sys/kernel/sysrq
:/# echo b > /proc/sysrq-trigger
[ 28.476745] sysrq: SysRq : Resetting
[ 28.476793] Kernel stack overflow.
[ 28.476817] CPU: 0 PID: 424 Comm: sh Not tainted 5.0.0-rc1+ #13
[ 28.476820] Hardware name: IBM 2964 NE1 716 (KVM/Linux)
[ 28.476826] Krnl PSW : 0400c00180000000 0000000000115c0c (pcpu_delegate+0x12c/0x140)
[ 28.476861] R:0 T:1 IO:0 EX:0 Key:0 M:0 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
[ 28.476863] Krnl GPRS: ffffffffffffffff 0000000000000000 000000000010dff8 0000000000000000
[ 28.476864] 0000000000000000 0000000000000000 0000000000ab7090 000003e0006efbf0
[ 28.476864] 000000000010dff8 0000000000000000 0000000000000000 0000000000000000
[ 28.476865] 000000007fffc000 0000000000730408 000003e0006efc58 0000000000000000
[ 28.476887] Krnl Code: 0000000000115bfe: 4170f000 la %r7,0(%r15)
[ 28.476887] 0000000000115c02: 41f0a000 la %r15,0(%r10)
[ 28.476887] #0000000000115c06: e370f0980024 stg %r7,152(%r15)
[ 28.476887] >0000000000115c0c: c0e5fffff86e brasl %r14,114ce8
[ 28.476887] 0000000000115c12: 41f07000 la %r15,0(%r7)
[ 28.476887] 0000000000115c16: a7f4ffa8 brc 15,115b66
[ 28.476887] 0000000000115c1a: 0707 bcr 0,%r7
[ 28.476887] 0000000000115c1c: 0707 bcr 0,%r7
[ 28.476901] Call Trace:
[ 28.476902] Last Breaking-Event-Address:
[ 28.476920] [<0000000000a01c4a>] arch_call_rest_init+0x22/0x80
[ 28.476927] Kernel panic - not syncing: Corrupt kernel stack, can't continue.
[ 28.476930] CPU: 0 PID: 424 Comm: sh Not tainted 5.0.0-rc1+ #13
[ 28.476932] Hardware name: IBM 2964 NE1 716 (KVM/Linux)
[ 28.476932] Call Trace:
Fixes: 2f859d0dad ("s390/smp: reduce size of struct pcpu")
Cc: stable@vger.kernel.org # 4.0+
Reported-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20c27a4270 upstream.
__sync_icache_dcache unconditionally skips the cache maintenance for
anonymous pages, under the assumption that flushing is only required in
the presence of D-side aliases [see 7249b79f6b ("arm64: Do not flush
the D-cache for anonymous pages")].
Unfortunately, this breaks migration of anonymous pages holding
self-modifying code, where userspace cannot be reasonably expected to
reissue maintenance instructions in response to a migration.
This patch fixes the problem by removing the broken page_mapping(page)
check from the cache syncing code, otherwise we may end up fetching and
executing stale instructions from the PoU.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Amanieu d'Antras <amanieu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8208d1708b upstream.
The way we allocate events works fine in most cases, except
when multiple PCI devices share an ITS-visible DevID, and that
one of them is trying to use MultiMSI allocation.
In that case, our allocation is not guaranteed to be zero-based
anymore, and we have to make sure we allocate it on a boundary
that is compatible with the PCI Multi-MSI constraints.
Fix this by allocating the full region upfront instead of iterating
over the number of MSIs. MSI-X are always allocated one by one,
so this shouldn't change anything on that front.
Fixes: b48ac83d6b ("irqchip: GICv3: ITS: MSI support")
Cc: stable@vger.kernel.org
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[ardb: rebased onto v4.9.153, should apply cleanly onto v4.4.y as well]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
commit 7b12c8189a upstream.
This patch revert commit 7da11ba5c5
("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
After introduction of this change we encountered following new error
message on various i.MX plattforms (flexcan):
| flexcan 53fc8000.can can0: __can_get_echo_skb: BUG! Trying to echo non
| existing skb: can_priv::echo_skb[0]
The introduction of the message was a mistake because
priv->echo_skb[idx] = NULL is a perfectly valid in following case: If
CAN_RAW_LOOPBACK is disabled (setsockopt) in applications, the pkt_type
of the tx skb's given to can_put_echo_skb is set to PACKET_LOOPBACK. In
this case can_put_echo_skb will not set priv->echo_skb[idx]. It is
therefore kept NULL.
As additional argument for revert: The order of check and usage of idx
was changed. idx is used to access an array element before checking it's
boundaries.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Fixes: 7da11ba5c5 ("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cc244a20b upstream.
The single-step debugging of KVM guests on x86 is broken: if we run
gdb 'stepi' command at the breakpoint when the guest interrupts are
enabled, RIP always jumps to native_apic_mem_write(). Then other
nasty effects follow.
Long investigation showed that on Jun 7, 2017 the
commit c8401dda2f ("KVM: x86: fix singlestepping over syscall")
introduced the kvm_run.debug corruption: kvm_vcpu_do_singlestep() can
be called without X86_EFLAGS_TF set.
Let's fix it. Please consider that for -stable.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Cc: stable@vger.kernel.org
Fixes: c8401dda2f ("KVM: x86: fix singlestepping over syscall")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe2bfd0d40 upstream.
Add support for the SteelSeries Stratus Duo, a wireless Xbox 360
controller. The Stratus Duo ships with a USB dongle to enable wireless
connectivity, but it can also function as a wired controller by connecting
it directly to a PC via USB, hence the need for two USD PIDs. 0x1430 is the
dongle, and 0x1431 is the controller.
Signed-off-by: Tom Panfil <tom@steelseries.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acc58d0bab upstream.
When doing MTU i/o we need to leave some credits for
possible reopen requests and other operations happening
in parallel. Currently we leave 1 credit which is not
enough even for reopen only: we need at least 2 credits
if durable handle reconnect fails. Also there may be
other operations at the same time including compounding
ones which require 3 credits at a time each. Fix this
by leaving 8 credits which is big enough to cover most
scenarios.
Was able to reproduce this when server was configured
to give out fewer credits than usual.
The proper fix would be to reconnect a file handle first
and then obtain credits for an MTU request but this leads
to bigger code changes and should happen in other patches.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27cfb3a53b upstream.
Some tty line disciplines do not have a receive buf callback, so
properly check for that before calling it. If they do not have this
callback, just eat the character quietly, as we can't fail this call.
Reported-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 701956d401 upstream.
ipcnum is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/char/mwave/mwavedd.c:299 mwave_ioctl() warn: potential spectre issue 'pDrvData->IPCs' [w] (local cap)
Fix this by sanitizing ipcnum before using it to index pDrvData->IPCs.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7cb707c37 upstream.
smp_rescan_cpus() is called without the device_hotplug_lock, which can lead
to a dedlock when a new CPU is found and immediately set online by a udev
rule.
This was observed on an older kernel version, where the cpu_hotplug_begin()
loop was still present, and it resulted in hanging chcpu and systemd-udev
processes. This specific deadlock will not show on current kernels. However,
there may be other possible deadlocks, and since smp_rescan_cpus() can still
trigger a CPU hotplug operation, the device_hotplug_lock should be held.
For reference, this was the deadlock with the old cpu_hotplug_begin() loop:
chcpu (rescan) systemd-udevd
echo 1 > /sys/../rescan
-> smp_rescan_cpus()
-> (*) get_online_cpus()
(increases refcount)
-> smp_add_present_cpu()
(new CPU found)
-> register_cpu()
-> device_add()
-> udev "add" event triggered -----------> udev rule sets CPU online
-> echo 1 > /sys/.../online
-> lock_device_hotplug_sysfs()
(this is missing in rescan path)
-> device_online()
-> (**) device_lock(new CPU dev)
-> cpu_up()
-> cpu_hotplug_begin()
(loops until refcount == 0)
-> deadlock with (*)
-> bus_probe_device()
-> device_attach()
-> device_lock(new CPU dev)
-> deadlock with (**)
Fix this by taking the device_hotplug_lock in the CPU rescan path.
Cc: <stable@vger.kernel.org>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03aa047ef2 upstream.
Right now the early machine detection code check stsi 3.2.2 for "KVM"
and set MACHINE_IS_VM if this is different. As the console detection
uses diagnose 8 if MACHINE_IS_VM returns true this will crash Linux
early for any non z/VM system that sets a different value than KVM.
So instead of assuming z/VM, do not set any of MACHINE_IS_LPAR,
MACHINE_IS_VM, or MACHINE_IS_KVM.
CC: stable@vger.kernel.org
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3affbf0e15 upstream.
So far we've mapped branches to "ijmp" which also counts conditional
branches NOT taken. This makes us different from other architectures
such as ARM which seem to be counting only taken branches.
So use "ijmptak" hardware condition which only counts (all jump
instructions that are taken)
'ijmptak' event is available on both ARCompact and ARCv2 ISA based
cores.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: reworked changelog]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 28c1382fa2 ]
The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).
To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1
So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.
Fixes: f6367b4660 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd0c4e70fc ]
Martin reported a set of filters don't work after changing
from reclassify to continue. Looking into the code, it
looks like skb protocol is not always fetched for each
iteration of the filters. But, as demonstrated by Martin,
TC actions could modify skb->protocol, for example act_vlan,
this means we have to refetch skb protocol in each iteration,
rather than using the one we fetch in the beginning of the loop.
This bug is _not_ introduced by commit 3b3ae88026
("net: sched: consolidate tc_classify{,_compat}"), technically,
if act_vlan is the only action that modifies skb protocol, then
it is commit c7e2b9689e ("sched: introduce vlan action") which
introduced this bug.
Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f97f4dd8b3 ]
IPv4 routing tables are flushed in two cases:
1. In response to events in the netdev and inetaddr notification chains
2. When a network namespace is being dismantled
In both cases only routes associated with a dead nexthop group are
flushed. However, a nexthop group will only be marked as dead in case it
is populated with actual nexthops using a nexthop device. This is not
the case when the route in question is an error route (e.g.,
'blackhole', 'unreachable').
Therefore, when a network namespace is being dismantled such routes are
not flushed and leaked [1].
To reproduce:
# ip netns add blue
# ip -n blue route add unreachable 192.0.2.0/24
# ip netns del blue
Fix this by not skipping error routes that are not marked with
RTNH_F_DEAD when flushing the routing tables.
To prevent the flushing of such routes in case #1, add a parameter to
fib_table_flush() that indicates if the table is flushed as part of
namespace dismantle or not.
Note that this problem does not exist in IPv6 since error routes are
associated with the loopback device.
[1]
unreferenced object 0xffff888066650338 (size 56):
comm "ip", pid 1206, jiffies 4294786063 (age 26.235s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 b0 1c 62 61 80 88 ff ff ..........ba....
e8 8b a1 64 80 88 ff ff 00 07 00 08 fe 00 00 00 ...d............
backtrace:
[<00000000856ed27d>] inet_rtm_newroute+0x129/0x220
[<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20
[<00000000cb85801a>] netlink_rcv_skb+0x132/0x380
[<00000000ebc991d2>] netlink_unicast+0x4c0/0x690
[<0000000014f62875>] netlink_sendmsg+0x929/0xe10
[<00000000bac9d967>] sock_sendmsg+0xc8/0x110
[<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0
[<000000002e94f880>] __sys_sendmsg+0xf7/0x250
[<00000000ccb1fa72>] do_syscall_64+0x14d/0x610
[<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<000000003a8b605b>] 0xffffffffffffffff
unreferenced object 0xffff888061621c88 (size 48):
comm "ip", pid 1206, jiffies 4294786063 (age 26.235s)
hex dump (first 32 bytes):
6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
6b 6b 6b 6b 6b 6b 6b 6b d8 8e 26 5f 80 88 ff ff kkkkkkkk..&_....
backtrace:
[<00000000733609e3>] fib_table_insert+0x978/0x1500
[<00000000856ed27d>] inet_rtm_newroute+0x129/0x220
[<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20
[<00000000cb85801a>] netlink_rcv_skb+0x132/0x380
[<00000000ebc991d2>] netlink_unicast+0x4c0/0x690
[<0000000014f62875>] netlink_sendmsg+0x929/0xe10
[<00000000bac9d967>] sock_sendmsg+0xc8/0x110
[<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0
[<000000002e94f880>] __sys_sendmsg+0xf7/0x250
[<00000000ccb1fa72>] do_syscall_64+0x14d/0x610
[<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<000000003a8b605b>] 0xffffffffffffffff
Fixes: 8cced9eff1 ("[NETNS]: Enable routing configuration in non-initial namespace.")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04a4af334b ]
For nested and variable attributes, the expected length of an attribute
is not known and marked by a negative number. This results in an OOB
read when the expected length is later used to check if the attribute is
all zeros. Fix this by using the actual length of the attribute rather
than the expected length.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c57f04580 ]
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d6380cd40 upstream.
The block number was not being compared right, it was off by one
when checking the response.
Some statistics wouldn't be incremented properly in some cases.
Check to see if that middle-part messages always have 31 bytes of
data.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c90584c66 upstream.
As measured in my prior patch ("sch_netem: faster rb tree removal"),
rbtree_postorder_for_each_entry_safe() is nice looking but much slower
than using rb_next() directly, except when tree is small enough
to fit in CPU caches (then the cost is the same)
Also note that there is not even an increase of text size :
$ size net/core/skbuff.o.before net/core/skbuff.o
text data bss dec hex filename
40711 1298 0 42009 a419 net/core/skbuff.o.before
40711 1298 0 42009 a419 net/core/skbuff.o
From: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
