commit e8a66d8004 upstream.
Symptom: After vnicc/rx_bcast has been manually set to 0,
bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.
Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.
Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68c57bfd52 upstream.
Symptom: Error message "Configuring the VNIC characteristics failed"
in dmesg whenever an OSA interface on z15 is set online.
The VNIC characteristics get re-programmed when setting a L2 device
online. This follows the selected 'wanted' characteristics - with the
exception that the INVISIBLE characteristic unconditionally gets
switched off.
For devices that don't support INVISIBLE (ie. OSA), the resulting
IO failure raises a noisy error message
("Configuring the VNIC characteristics failed").
For IQD, INVISIBLE is off by default anyways.
So don't unnecessarily special-case the INVISIBLE characteristic, and
thereby suppress the misleading error message on OSA devices.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00b39f698a ]
If for whatever reason the dasd_eckd_check_characteristics() function
exits after at least some paths have their configuration data
allocated those data is never freed again. In the error case the
device->private pointer is set to NULL and dasd_eckd_uncheck_device()
will exit without freeing the path data because of this NULL pointer.
Fix by calling dasd_eckd_clear_conf_data() for error cases.
Also use dasd_eckd_clear_conf_data() in dasd_eckd_uncheck_device()
to avoid code duplication.
Reported-by: Qian Cai <cai@lca.pw>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd4b3c83b9 ]
The max data count (mdc) is an unsigned 16-bit integer value as per AR
documentation and is received via ccw_device_get_mdc() for a specific
path mask from the CIO layer. The function itself also always returns a
positive mdc value or 0 in case mdc isn't supported or couldn't be
determined.
Though, the comment for this function describes a negative return value
to indicate failures.
As a result, the DASD device driver interprets the return value of
ccw_device_get_mdc() incorrectly. The error case is essentially a dead
code path.
To fix this behaviour, check explicitly for a return value of 0 and
change the comment for ccw_device_get_mdc() accordingly.
This fix merely enables the error code path in the DASD functions
get_fcx_max_data() and verify_fcx_max_data(). The actual functionality
stays the same and is still correct.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6733775a92 ]
This patch introduces support for a new architectured reply
code 0x8B indicating that a hypervisor layer (if any) has
rejected an ap message.
Linux may run as a guest on top of a hypervisor like zVM
or KVM. So the crypto hardware seen by the ap bus may be
restricted by the hypervisor for example only a subset like
only clear key crypto requests may be supported. Other
requests will be filtered out - rejected by the hypervisor.
The new reply code 0x8B will appear in such cases and needs
to get recognized by the ap bus and zcrypt device driver zoo.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c902936e5 ]
This was introduced with v4.18 commit 8c3d20aada ("scsi: zfcp: fix
missing REC trigger trace for all objects in ERP_FAILED") but would now
suppress helpful -Wswitch compiler warnings when building with W=1 such as
the following forced example:
drivers/s390/scsi/zfcp_erp.c: In function 'zfcp_erp_handle_failed':
drivers/s390/scsi/zfcp_erp.c:126:2: warning: enumeration value 'ZFCP_ERP_ACTION_REOPEN_PORT_FORCED' not handled in switch [-Wswitch]
switch (want) {
^~~~~~
But then again, only with W=1 we would notice unhandled enum cases.
Without the default cases and a missed unhandled enum case, the code might
perform unforeseen things we might not want...
As of today, we never run through the removed default case, so removing it
is no functional change. In the future, we never should run through a
default case but introduce the necessary specific case(s) to handle new
functionality.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 724e144387 ]
The CDB is just a part inside of FCP_CMND, see zfcp_fc_scsi_to_fcp().
While at it, fix the device driver reaction: adapter not LUN shutdown.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42a87d4103 ]
Until now there is no way to reset a AP queue or card. Driving a card
or queue offline and online again does only toggle the 'software'
online state. The only way to trigger a (hardware) reset is by running
hot-unplug/hot-plug for example on the HMC.
This patch makes the queue reset attribute in sysfs writable.
Writing into this attribute triggers a reset on the AP queue's state
machine. So the AP queue is flushed and state machine runs through the
initial states which cause a reset (PQAP(RAPQ)) and a re-registration
to interrupts (PQAP(AQIC)) if available.
The reset sysfs attribute is writable by root only. So only an
administrator is allowed to initiate a reset of AP queues. Please note
that the queue's counter values are left untouched by the reset.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a9b40911b ]
Instrumented C code cannot run without the kasan shadow area. Exempt
source code files from kasan which are running before / used during
kasan initialization.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c472d4628 ]
The AP bus scan is aborted before doing anything worth mentioning if
ap_select_domain() fails, e.g. if the ap_rights.aqm mask is all zeros.
As the result of this the ap bus fails to manage (e.g. create and
register) devices like it is supposed to.
Let us make ap_scan_bus() work even if ap_select_domain() can't select a
default domain. Let's also make ap_select_domain() return void, as there
are no more callers interested in its return value.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reported-by: Michael Mueller <mimu@linux.ibm.com>
Fixes: 7e0bdbe5c2 "s390/zcrypt: AP bus support for alternate driver(s)"
[freude@linux.ibm.com: title and patch header slightly modified]
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d19db777a ]
Calling napi_schedule() from process context does not ensure that the
NET_RX softirq is run in a timely fashion. So trigger it manually.
This is no big issue with current code. A call to ndo_open() is usually
followed by a ndo_set_rx_mode() call, and for qeth this contains a
spin_unlock_bh(). Except for OSN, where qeth_l2_set_rx_mode() bails out
early.
Nevertheless it's best to not depend on this behaviour, and just fix
the issue at its source like all other drivers do. For instance see
commit 83a0c6e589 ("i40e: Invoke softirqs after napi_reschedule").
Fixes: a1c3ed4c9c ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 121ca39aa5 ]
When setting up, qeth installs its IRQ handler on the ccw devices. But
the IRQ handler is not cleared on removal - so even after qeth yields
control of the ccw devices, spurious interrupts would still be presented
to us.
Make (de-)installation of the IRQ handler part of the ccw channel
setup/removal helpers, and while at it also add the appropriate locking.
Shift around qeth_setup_channel() to avoid a forward declaration for
qeth_irq().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2190168aae upstream.
On excessive bit errors for the FCP channel ingress fibre path, the channel
notifies us. Previously, we only emitted a kernel message and a trace
record. Since performance can become suboptimal with I/O timeouts due to
bit errors, we now stop using an FCP device by default on channel
notification so multipath on top can timely failover to other paths. A new
module parameter zfcp.ber_stop can be used to get zfcp old behavior.
User explanation of new kernel message:
* Description:
* The FCP channel reported that its bit error threshold has been exceeded.
* These errors might result from a problem with the physical components
* of the local fibre link into the FCP channel.
* The problem might be damage or malfunction of the cable or
* cable connection between the FCP channel and
* the adjacent fabric switch port or the point-to-point peer.
* Find details about the errors in the HBA trace for the FCP device.
* The zfcp device driver closed down the FCP device
* to limit the performance impact from possible I/O command timeouts.
* User action:
* Check for problems on the local fibre link, ensure that fibre optics are
* clean and functional, and all cables are properly plugged.
* After the repair action, you can manually recover the FCP device by
* writing "0" into its "failed" sysfs attribute.
* If recovery through sysfs is not possible, set the CHPID of the device
* offline and back online on the service element.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org> #2.6.30+
Link: https://lore.kernel.org/r/20191001104949.42810-1-maier@linux.ibm.com
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea298e6ee8 upstream.
Fix the following kasan finding:
BUG: KASAN: global-out-of-bounds in ccwgroup_create_dev+0x850/0x1140
Read of size 1 at addr 0000000000000000 by task systemd-udevd.r/561
CPU: 30 PID: 561 Comm: systemd-udevd.r Tainted: G B
Hardware name: IBM 3906 M04 704 (LPAR)
Call Trace:
([<0000000231b3db7e>] show_stack+0x14e/0x1a8)
[<0000000233826410>] dump_stack+0x1d0/0x218
[<000000023216fac4>] print_address_description+0x64/0x380
[<000000023216f5a8>] __kasan_report+0x138/0x168
[<00000002331b8378>] ccwgroup_create_dev+0x850/0x1140
[<00000002332b618a>] group_store+0x3a/0x50
[<00000002323ac706>] kernfs_fop_write+0x246/0x3b8
[<00000002321d409a>] vfs_write+0x132/0x450
[<00000002321d47da>] ksys_write+0x122/0x208
[<0000000233877102>] system_call+0x2a6/0x2c8
Triggered by:
openat(AT_FDCWD, "/sys/bus/ccwgroup/drivers/qeth/group",
O_WRONLY|O_CREAT|O_TRUNC|O_CLOEXEC, 0666) = 16
write(16, "0.0.bd00,0.0.bd01,0.0.bd02", 26) = 26
The problem is that __get_next_id in ccwgroup_create_dev might set "buf"
buffer pointer to NULL and explicit check for that is required.
Cc: stable@vger.kernel.org
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab57588480 upstream.
ccw console is created early in start_kernel and used before css is
initialized or ccw console subchannel is registered. Until then console
subchannel does not have a parent. For that reason assume subchannels
with no parent are not pseudo subchannels. This fixes the following
kasan finding:
BUG: KASAN: global-out-of-bounds in sch_is_pseudo_sch+0x8e/0x98
Read of size 8 at addr 00000000000005e8 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc8-07370-g6ac43dd12538 #2
Hardware name: IBM 2964 NC9 702 (z/VM 6.4.0)
Call Trace:
([<000000000012cd76>] show_stack+0x14e/0x1e0)
[<0000000001f7fb44>] dump_stack+0x1a4/0x1f8
[<00000000007d7afc>] print_address_description+0x64/0x3c8
[<00000000007d75f6>] __kasan_report+0x14e/0x180
[<00000000018a2986>] sch_is_pseudo_sch+0x8e/0x98
[<000000000189b950>] cio_enable_subchannel+0x1d0/0x510
[<00000000018cac7c>] ccw_device_recognition+0x12c/0x188
[<0000000002ceb1a8>] ccw_device_enable_console+0x138/0x340
[<0000000002cf1cbe>] con3215_init+0x25e/0x300
[<0000000002c8770a>] console_init+0x68a/0x9b8
[<0000000002c6a3d6>] start_kernel+0x4fe/0x728
[<0000000000100070>] startup_continue+0x70/0xd0
Cc: stable@vger.kernel.org
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f419eb142 ]
The access to airq_areas was racy ever since the adapter interrupts got
introduced to virtio-ccw, but since commit 39c7dcb158 ("virtio/s390:
make airq summary indicators DMA") this became an issue in practice as
well. Namely before that commit the airq_info that got overwritten was
still functional. After that commit however the two infos share a
summary_indicator, which aggravates the situation. Which means
auto-online mechanism occasionally hangs the boot with virtio_blk.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 96b14536d9 ("virtio-ccw: virtio-ccw adapter interrupt support.")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 106d45f350 ]
When tracing instances where we open and close WKA ports, we also pass the
request-ID of the respective FSF command.
But after successfully sending the FSF command we must not use the
request-object anymore, as this might result in an use-after-free (see
"zfcp: fix request object use-after-free in send path causing seqno
errors" ).
To fix this add a new variable that caches the request-ID before sending
the request. This won't change during the hand-off to the FCP channel,
and so it's safe to trace this cached request-ID later, instead of using
the request object.
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Fixes: d27a7cb919 ("zfcp: trace on request for open and close of WKA port")
Cc: <stable@vger.kernel.org> #2.6.38+
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 104f708fd1 ]
Until the vfio-ap driver came into live there was a well known
agreement about the way how ap devices are initialized and their
states when the driver's probe function is called.
However, the vfio device driver when receiving an ap queue device does
additional resets thereby removing the registration for interrupts for
the ap device done by the ap bus core code. So when later the vfio
driver releases the device and one of the default zcrypt drivers takes
care of the device the interrupt registration needs to get
renewed. The current code does no renew and result is that requests
send into such a queue will never see a reply processed - the
application hangs.
This patch adds a function which resets the aq queue state machine for
the ap queue device and triggers the walk through the initial states
(which are reset and registration for interrupts). This function is
now called before the driver's probe function is invoked.
When the association between driver and device is released, the
driver's remove function is called. The current implementation calls a
ap queue function ap_queue_remove(). This invokation has been moved to
the ap bus function to make the probe / remove pair for ap bus and
drivers more symmetric.
Fixes: 7e0bdbe5c2 ("s390/zcrypt: AP bus support for alternate driver(s)")
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewd-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewd-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6ec414a4d ]
If the device driver were to send out a full queue's worth of SBALs,
current code would end up discovering the last of those SBALs as PRIMED
and erroneously skip the SIGA-w. This immediately stalls the queue.
Add a check to not attempt fast-requeue in this case. While at it also
make sure that the state of the previous SBAL was successfully extracted
before inspecting it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 41995342b4 upstream.
After getting a storage server event that causes the DASD device driver
to update its unit address configuration during a device shutdown there is
the possibility of an endless loop in the device driver.
In the system log there will be ongoing DASD error messages with RC: -19.
The reason is that the loop starting the ruac request only terminates when
the retry counter is decreased to 0. But in the sleep_on function there are
early exit paths that do not decrease the retry counter.
Prevent an endless loop by handling those cases separately.
Remove the unnecessary do..while loop since the sleep_on function takes
care of retries by itself.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org # 2.6.25+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4846470888 ]
GCC v9 emits this warning:
CC drivers/s390/scsi/zfcp_erp.o
drivers/s390/scsi/zfcp_erp.c: In function 'zfcp_erp_action_enqueue':
drivers/s390/scsi/zfcp_erp.c:217:26: warning: 'erp_action' may be used uninitialized in this function [-Wmaybe-uninitialized]
217 | struct zfcp_erp_action *erp_action;
| ^~~~~~~~~~
This is a possible false positive case, as also documented in the GCC
documentations:
https://gcc.gnu.org/onlinedocs/gcc/Warning-Options.html#index-Wmaybe-uninitialized
The actual code-sequence is like this:
Various callers can invoke the function below with the argument "want"
being one of:
ZFCP_ERP_ACTION_REOPEN_ADAPTER,
ZFCP_ERP_ACTION_REOPEN_PORT_FORCED,
ZFCP_ERP_ACTION_REOPEN_PORT, or
ZFCP_ERP_ACTION_REOPEN_LUN.
zfcp_erp_action_enqueue(want, ...)
...
need = zfcp_erp_required_act(want, ...)
need = want
...
maybe: need = ZFCP_ERP_ACTION_REOPEN_PORT
maybe: need = ZFCP_ERP_ACTION_REOPEN_ADAPTER
...
return need
...
zfcp_erp_setup_act(need, ...)
struct zfcp_erp_action *erp_action; // <== line 217
...
switch(need) {
case ZFCP_ERP_ACTION_REOPEN_LUN:
...
erp_action = &zfcp_sdev->erp_action;
WARN_ON_ONCE(erp_action->port != port); // <== access
...
break;
case ZFCP_ERP_ACTION_REOPEN_PORT:
case ZFCP_ERP_ACTION_REOPEN_PORT_FORCED:
...
erp_action = &port->erp_action;
WARN_ON_ONCE(erp_action->port != port); // <== access
...
break;
case ZFCP_ERP_ACTION_REOPEN_ADAPTER:
...
erp_action = &adapter->erp_action;
WARN_ON_ONCE(erp_action->port != NULL); // <== access
...
break;
}
...
WARN_ON_ONCE(erp_action->adapter != adapter); // <== access
When zfcp_erp_setup_act() is called, 'need' will never be anything else
than one of the 4 possible enumeration-names that are used in the
switch-case, and 'erp_action' is initialized for every one of them, before
it is used. Thus the warning is a false positive, as documented.
We introduce the extra if{} in the beginning to create an extra code-flow,
so the compiler can be convinced that the switch-case will never see any
other value.
BUG_ON()/BUG() is intentionally not used to not crash anything, should
this ever happen anyway - right now it's impossible, as argued above; and
it doesn't introduce a 'default:' switch-case to retain warnings should
'enum zfcp_erp_act_type' ever be extended and no explicit case be
introduced. See also v5.0 commit 399b6c8bc9 ("scsi: zfcp: drop old
default switch case which might paper over missing case").
Signed-off-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04310324c6 ]
When a CQ-enabled device uses QEBSM for SBAL state inspection,
get_buf_states() can return the PENDING state for an Output Queue.
get_outbound_buffer_frontier() isn't prepared for this, and any PENDING
buffer will permanently stall all further completion processing on this
Queue.
This isn't a concern for non-QEBSM devices, as get_buf_states() for such
devices will manually turn PENDING buffers into EMPTY ones.
Fixes: 104ea556ee ("qdio: support asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ac6639cd3d upstream.
Current code sets the dsci to 0x00000080. Which doesn't make any sense,
as the indicator area is located in the _left-most_ byte.
Worse: if the dsci is the _shared_ indicator, this potentially clears
the indication of activity for a _different_ device.
tiqdio_thinint_handler() will then have no reason to call that device's
IRQ handler, and the device ends up stalling.
Fixes: d0c9d4a89f ("[S390] qdio: set correct bit in dsci")
Cc: <stable@vger.kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e54e4785cb upstream.
When tiqdio_remove_input_queues() removes a queue from the tiq_list as
part of qdio_shutdown(), it doesn't re-initialize the queue's list entry
and the prev/next pointers go stale.
If a subsequent qdio_establish() fails while sending the ESTABLISH cmd,
it calls qdio_shutdown() again in QDIO_IRQ_STATE_ERR state and
tiqdio_remove_input_queues() will attempt to remove the queue entry a
second time. This dereferences the stale pointers, and bad things ensue.
Fix this by re-initializing the list entry after removing it from the
list.
For good practice also initialize the list entry when the queue is first
allocated, and remove the quirky checks that papered over this omission.
Note that prior to
commit e521813468 ("s390/qdio: fix access to uninitialized qdio_q fields"),
these checks were bogus anyway.
setup_queues_misc() clears the whole queue struct, and thus needs to
re-init the prev/next pointers as well.
Fixes: 779e6e1c72 ("[S390] qdio: new qdio driver.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 335726195e ]
Enabling sysfs attribute bridge_hostnotify triggers a series of udev events
for the MAC addresses of all currently connected peers. In case no VLAN is
set for a peer, the device reports the corresponding MAC addresses with
VLAN ID 4096. This currently results in attribute VLAN=4096 for all
non-VLAN interfaces in the initial series of events after host-notify is
enabled.
Instead, no VLAN attribute should be reported in the udev event for
non-VLAN interfaces.
Only the initial events face this issue. For dynamic changes that are
reported later, the device uses a validity flag.
This also changes the code so that it now sets the VLAN attribute for
MAC addresses with VID 0. On Linux, no qeth interface will ever be
registered with VID 0: Linux kernel registers VID 0 on all network
interfaces initially, but qeth will drop .ndo_vlan_rx_add_vid for VID 0.
Peers with other OSs could register MACs with VID 0.
Fixes: 9f48b9db9a ("qeth: bridgeport support - address notifications")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ef4021fe5f upstream.
When the user tries to remove a zfcp port via sysfs, we only rejected it if
there are zfcp unit children under the port. With purely automatically
scanned LUNs there are no zfcp units but only SCSI devices. In such cases,
the port_remove erroneously continued. We close the port and this
implicitly closes all LUNs under the port. The SCSI devices survive with
their private zfcp_scsi_dev still holding a reference to the "removed"
zfcp_port (still allocated but invisible in sysfs) [zfcp_get_port_by_wwpn
in zfcp_scsi_slave_alloc]. This is not a problem as long as the fc_rport
stays blocked. Once (auto) port scan brings back the removed port, we
unblock its fc_rport again by design. However, there is no mechanism that
would recover (open) the LUNs under the port (no "ersfs_3" without
zfcp_unit [zfcp_erp_strategy_followup_success]). Any pending or new I/O to
such LUN leads to repeated:
Done: NEEDS_RETRY Result: hostbyte=DID_IMM_RETRY driverbyte=DRIVER_OK
See also v4.10 commit 6f2ce1c6af ("scsi: zfcp: fix rport unblock race
with LUN recovery"). Even a manual LUN recovery
(echo 0 > /sys/bus/scsi/devices/H:C:T:L/zfcp_failed)
does not help, as the LUN links to the old "removed" port which remains
to lack ZFCP_STATUS_COMMON_RUNNING [zfcp_erp_required_act].
The only workaround is to first ensure that the fc_rport is blocked
(e.g. port_remove again in case it was re-discovered by (auto) port scan),
then delete the SCSI devices, and finally re-discover by (auto) port scan.
The port scan includes an fc_rport unblock, which in turn triggers
a new scan on the scsi target to freshly get new pure auto scan LUNs.
Fix this by rejecting port_remove also if there are SCSI devices
(even without any zfcp_unit) under this port. Re-use mechanics from v3.7
commit d99b601b63 ("[SCSI] zfcp: restore refcount check on port_remove").
However, we have to give up zfcp_sysfs_port_units_mutex earlier in unit_add
to prevent a deadlock with scsi_host scan taking shost->scan_mutex first
and then zfcp_sysfs_port_units_mutex now in our zfcp_scsi_slave_alloc().
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: b62a8d9b45 ("[SCSI] zfcp: Use SCSI device data zfcp scsi dev instead of zfcp unit")
Fixes: f8210e3488 ("[SCSI] zfcp: Allow midlayer to scan for LUNs when running in NPIV mode")
Cc: <stable@vger.kernel.org> #2.6.37+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d1ffa760d2 ]
The quiesce function calls cio_cancel_halt_clear() and if we
get an -EBUSY we go into a loop where we:
- wait for any interrupts
- flush all I/O in the workqueue
- retry cio_cancel_halt_clear
During the period where we are waiting for interrupts or
flushing all I/O, the channel subsystem could have completed
a halt/clear action and turned off the corresponding activity
control bits in the subchannel status word. This means the next
time we call cio_cancel_halt_clear(), we will again start by
calling cancel subchannel and so we can be stuck between calling
cancel and halt forever.
Rather than calling cio_cancel_halt_clear() immediately after
waiting, let's try to disable the subchannel. If we succeed in
disabling the subchannel then we know nothing else can happen
with the device.
Suggested-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <4d5a4b98ab1b41ac6131b5c36de18b76c5d66898.1555449329.git.alifm@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e91012ee85 ]
clang points out that the declaration of cio_irb does not match the
definition exactly, it is missing the alignment attribute:
../drivers/s390/cio/cio.c:50:1: warning: section does not match previous declaration [-Wsection]
DEFINE_PER_CPU_ALIGNED(struct irb, cio_irb);
^
../include/linux/percpu-defs.h:150:2: note: expanded from macro 'DEFINE_PER_CPU_ALIGNED'
DEFINE_PER_CPU_SECTION(type, name, PER_CPU_ALIGNED_SECTION) \
^
../include/linux/percpu-defs.h:93:9: note: expanded from macro 'DEFINE_PER_CPU_SECTION'
extern __PCPU_ATTRS(sec) __typeof__(type) name; \
^
../include/linux/percpu-defs.h:49:26: note: expanded from macro '__PCPU_ATTRS'
__percpu __attribute__((section(PER_CPU_BASE_SECTION sec))) \
^
../drivers/s390/cio/cio.h:118:1: note: previous attribute is here
DECLARE_PER_CPU(struct irb, cio_irb);
^
../include/linux/percpu-defs.h:111:2: note: expanded from macro 'DECLARE_PER_CPU'
DECLARE_PER_CPU_SECTION(type, name, "")
^
../include/linux/percpu-defs.h:87:9: note: expanded from macro 'DECLARE_PER_CPU_SECTION'
extern __PCPU_ATTRS(sec) __typeof__(type) name
^
../include/linux/percpu-defs.h:49:26: note: expanded from macro '__PCPU_ATTRS'
__percpu __attribute__((section(PER_CPU_BASE_SECTION sec))) \
^
Use DECLARE_PER_CPU_ALIGNED() here, to make the two match.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 913140e221 ]
The 'func_code' variable gets printed in debug statements without
a prior initialization in multiple functions, as reported when building
with clang:
drivers/s390/crypto/zcrypt_api.c:659:6: warning: variable 'func_code' is used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (mex->outputdatalength < mex->inputdatalength) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/s390/crypto/zcrypt_api.c:725:29: note: uninitialized use occurs here
trace_s390_zcrypt_rep(mex, func_code, rc,
^~~~~~~~~
drivers/s390/crypto/zcrypt_api.c:659:2: note: remove the 'if' if its condition is always false
if (mex->outputdatalength < mex->inputdatalength) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/s390/crypto/zcrypt_api.c:654:24: note: initialize the variable 'func_code' to silence this warning
unsigned int func_code;
^
Add initializations to all affected code paths to shut up the warning
and make the warning output consistent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4cdc9baee ]
Subsequent code relies on the values that qeth_update_from_chp_desc()
reads from the CHP descriptor. Rather than dealing with weird errors
later on, just handle it properly here.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b49bdc8602 ]
When releasing the vfio-ccw mdev, we currently do not release
any existing channel program and its pinned pages. This can
lead to the following warning:
[1038876.561565] WARNING: CPU: 2 PID: 144727 at drivers/vfio/vfio_iommu_type1.c:1494 vfio_sanity_check_pfn_list+0x40/0x70 [vfio_iommu_type1]
....
1038876.561921] Call Trace:
[1038876.561935] ([<00000009897fb870>] 0x9897fb870)
[1038876.561949] [<000003ff8013bf62>] vfio_iommu_type1_detach_group+0xda/0x2f0 [vfio_iommu_type1]
[1038876.561965] [<000003ff8007b634>] __vfio_group_unset_container+0x64/0x190 [vfio]
[1038876.561978] [<000003ff8007b87e>] vfio_group_put_external_user+0x26/0x38 [vfio]
[1038876.562024] [<000003ff806fc608>] kvm_vfio_group_put_external_user+0x40/0x60 [kvm]
[1038876.562045] [<000003ff806fcb9e>] kvm_vfio_destroy+0x5e/0xd0 [kvm]
[1038876.562065] [<000003ff806f63fc>] kvm_put_kvm+0x2a4/0x3d0 [kvm]
[1038876.562083] [<000003ff806f655e>] kvm_vm_release+0x36/0x48 [kvm]
[1038876.562098] [<00000000003c2dc4>] __fput+0x144/0x228
[1038876.562113] [<000000000016ee82>] task_work_run+0x8a/0xd8
[1038876.562125] [<000000000014c7a8>] do_exit+0x5d8/0xd90
[1038876.562140] [<000000000014d084>] do_group_exit+0xc4/0xc8
[1038876.562155] [<000000000015c046>] get_signal+0x9ae/0xa68
[1038876.562169] [<0000000000108d66>] do_signal+0x66/0x768
[1038876.562185] [<0000000000b9e37e>] system_call+0x1ea/0x2d8
[1038876.562195] 2 locks held by qemu-system-s39/144727:
[1038876.562205] #0: 00000000537abaf9 (&container->group_lock){++++}, at: __vfio_group_unset_container+0x3c/0x190 [vfio]
[1038876.562230] #1: 00000000670008b5 (&iommu->lock){+.+.}, at: vfio_iommu_type1_detach_group+0x36/0x2f0 [vfio_iommu_type1]
[1038876.562250] Last Breaking-Event-Address:
[1038876.562262] [<000003ff8013aa24>] vfio_sanity_check_pfn_list+0x3c/0x70 [vfio_iommu_type1]
[1038876.562272] irq event stamp: 4236481
[1038876.562287] hardirqs last enabled at (4236489): [<00000000001cee7a>] console_unlock+0x6d2/0x740
[1038876.562299] hardirqs last disabled at (4236496): [<00000000001ce87e>] console_unlock+0xd6/0x740
[1038876.562311] softirqs last enabled at (4234162): [<0000000000b9fa1e>] __do_softirq+0x556/0x598
[1038876.562325] softirqs last disabled at (4234153): [<000000000014e4cc>] irq_exit+0xac/0x108
[1038876.562337] ---[ end trace 6c96d467b1c3ca06 ]---
Similarly we do not free the channel program when we are removing
the vfio-ccw device. Let's fix this by resetting the device and freeing
the channel program and pinned pages in the release path. For the remove
path we can just quiesce the device, since in the remove path the mediated
device is going away for good and so we don't need to do a full reset.
Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <ae9f20dc8873f2027f7b3c5d2aaa0bdfe06850b8.1554756534.git.alifm@linux.ibm.com>
Acked-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46b83629de ]
clang produces a harmless warning for each use for the qeth_adp_supported
macro:
drivers/s390/net/qeth_l2_main.c:559:31: warning: implicit conversion from enumeration type 'enum qeth_ipa_setadp_cmd' to
different enumeration type 'enum qeth_ipa_funcs' [-Wenum-conversion]
if (qeth_adp_supported(card, IPA_SETADP_SET_PROMISC_MODE))
~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/s390/net/qeth_core.h:179:41: note: expanded from macro 'qeth_adp_supported'
qeth_is_ipa_supported(&c->options.adp, f)
~~~~~~~~~~~~~~~~~~~~~ ^
Add a version of this macro that uses the correct types, and
remove the unused qeth_adp_enabled() macro that has the same
problem.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27b141fc23 ]
clang points out that the return code from this function is
undefined for one of the error paths:
../drivers/s390/net/ctcm_main.c:1595:7: warning: variable 'result' is used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (priv->channel[direction] == NULL) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/s390/net/ctcm_main.c:1638:9: note: uninitialized use occurs here
return result;
^~~~~~
../drivers/s390/net/ctcm_main.c:1595:3: note: remove the 'if' if its condition is always false
if (priv->channel[direction] == NULL) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/s390/net/ctcm_main.c:1539:12: note: initialize the variable 'result' to silence this warning
int result;
^
Make it return -ENODEV here, as in the related failure cases.
gcc has a known bug in underreporting some of these warnings
when it has already eliminated the assignment of the return code
based on some earlier optimization step.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b1f16ba73 ]
The debug feature entries have been used with up to 5 arguents
(including the pointer to the format string) but there was only
space reserved for 4 arguemnts. So now the registration does
reserve space for 5 times a long value.
This fixes a sometime appearing weired value as the last
value of an debug feature entry like this:
... pkey_sec2protkey zcrypt_send_cprb (cardnr=10 domain=12)
failed with errno -2143346254
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Christian Rund <Christian.Rund@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5712f3301a ]
The spinlock in the raw3270_view structure is used by con3270, tty3270
and fs3270 in different ways. For con3270 the lock can be acquired in
irq context, for tty3270 and fs3270 the highest context is bh.
Lockdep sees the view->lock as a single class and if the 3270 driver
is used for the console the following message is generated:
WARNING: inconsistent lock state
5.1.0-rc3-05157-g5c168033979d #12 Not tainted
--------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
swapper/0/1 [HC0[0]:SC1[1]:HE1:SE0] takes:
(____ptrval____) (&(&view->lock)->rlock){?.-.}, at: tty3270_update+0x7c/0x330
Introduce a lockdep subclass for the view lock to distinguish bh from
irq locks.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cc9637ce8 ]
The DASD driver incorrectly limits the maximum number of blocks of ECKD
DASD volumes to 32 bit numbers. Volumes with a capacity greater than
2^32-1 blocks are incorrectly recognized as smaller volumes.
This results in the following volume capacity limits depending on the
formatted block size:
BLKSIZE MAX_GB MAX_CYL
512 2047 5843492
1024 4095 8676701
2048 8191 13634816
4096 16383 23860929
The same problem occurs when a volume with more than 17895697 cylinders
is accessed in raw-track-access mode.
Fix this problem by adding an explicit type cast when calculating the
maximum number of blocks.
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c820657917 ]
If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away. It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.
The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.
The call chain was:
zfcp_fc_incoming_rscn
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:
zfcp_fc_incoming_rscn
if (no_entries > 1) <===
list_for_each_entry(port, &adapter->port_list, list) <===
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
Abbreviated example trace records before this code change:
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x02
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x00 NOP => superfluous trace record
The last trace entry repeats if there are more than 2 RSCN elements.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
[ Upstream commit 7221b727f0 ]
The ucast IP table is utilized by some of the L3-specific sysfs attributes
that qeth_l3_create_device_attributes() provides. So initialize the table
_before_ registering the attributes.
Fixes: ebccc7397e ("s390/qeth: add missing hash table initializations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
[ Upstream commit 0ff06c44ef ]
Prior to dma unmap/free operations the ism driver tries to ensure
that the memory is no longer accessed by the HW. When errors
during deregistration of memory regions from the HW occur the ism
driver will not unmap/free this memory.
When we receive notification from the hypervisor that a PCI function
has been detached we can no longer access the device and would never
unmap/free these memory regions which led to complaints by the DMA
debug API.
Treat this kind of errors during the deregistration of memory regions
from the HW as success since it is already ensured that the memory
is no longer accessed by HW.
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Reported-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 242ec14551 upstream.
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit
ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org> #3.0+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe67888fc0 upstream.
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 6f2ce1c6af ("scsi: zfcp: fix rport unblock race with LUN recovery")
Cc: <stable@vger.kernel.org> #2.6.32+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50b7f1b723 upstream.
When we get an interrupt for a channel program, it is not
necessarily the final interrupt; for example, the issuing
guest may request an intermediate interrupt by specifying
the program-controlled-interrupt flag on a ccw.
We must not switch the state to idle if the interrupt is not
yet final; even more importantly, we must not free the translated
channel program if the interrupt is not yet final, or the host
can crash during cp rewind.
Fixes: e5f84dbaea ("vfio: ccw: return I/O results asynchronously")
Cc: stable@vger.kernel.org # v4.12+
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3438b2c039 upstream.
A queue with a capacity of zero is clearly not a valid virtio queue.
Some emulators report zero queue size if queried with an invalid queue
index. Instead of crashing in this case let us just return -ENOENT. To
make that work properly, let us fix the notifier cleanup logic as well.
Cc: stable@vger.kernel.org
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4a8ef6999b ]
Dan Carpenter reported the following:
The patch 52898025cf: "[S390] dasd: security and PSF update patch
for EMC CKD ioctl" from Mar 8, 2010, leads to the following static
checker warning:
drivers/s390/block/dasd_eckd.c:4486 dasd_symm_io()
error: using offset into zero size array 'psf_data[]'
drivers/s390/block/dasd_eckd.c
4458 /* Copy parms from caller */
4459 rc = -EFAULT;
4460 if (copy_from_user(&usrparm, argp, sizeof(usrparm)))
^^^^^^^
The user can specify any "usrparm.psf_data_len". They choose zero by
mistake.
4461 goto out;
4462 if (is_compat_task()) {
4463 /* Make sure pointers are sane even on 31 bit. */
4464 rc = -EINVAL;
4465 if ((usrparm.psf_data >> 32) != 0)
4466 goto out;
4467 if ((usrparm.rssd_result >> 32) != 0)
4468 goto out;
4469 usrparm.psf_data &= 0x7fffffffULL;
4470 usrparm.rssd_result &= 0x7fffffffULL;
4471 }
4472 /* alloc I/O data area */
4473 psf_data = kzalloc(usrparm.psf_data_len, GFP_KERNEL
| GFP_DMA);
4474 rssd_result = kzalloc(usrparm.rssd_result_len, GFP_KERNEL
| GFP_DMA);
4475 if (!psf_data || !rssd_result) {
kzalloc() returns a ZERO_SIZE_PTR (0x16).
4476 rc = -ENOMEM;
4477 goto out_free;
4478 }
4479
4480 /* get syscall header from user space */
4481 rc = -EFAULT;
4482 if (copy_from_user(psf_data,
4483 (void __user *)(unsigned long)
usrparm.psf_data,
4484 usrparm.psf_data_len))
That all works great.
4485 goto out_free;
4486 psf0 = psf_data[0];
4487 psf1 = psf_data[1];
But now we're assuming that "->psf_data_len" was at least 2 bytes.
Fix this by checking the user specified length psf_data_len.
Fixes: 52898025cf ("[S390] dasd: security and PSF update patch for EMC CKD ioctl")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2780c1a3f ]
A card's close_dev work is scheduled on a driver-wide workqueue. If the
card is removed and freed while the work is still active, this causes a
use-after-free.
So make sure that the work is completed before freeing the card.
Fixes: 0f54761d16 ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afa0c5904b ]
The error path in qeth_alloc_qdio_buffers() that takes care of
cleaning up the Output Queues is buggy. It first frees the queue, but
then calls qeth_clear_outq_buffers() with that very queue struct.
Make the call to qeth_clear_outq_buffers() part of the free action
(in the correct order), and while at it fix the naming of the helper.
Fixes: 0da9581ddb ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
