commit 64cc3f12d1 upstream.
When disconnecting a USB hub that has some child device(s) connected to it
(such as a USB mouse), then the stack tries to clear halt and
reset device(s) which are _already_ physically disconnected.
The issue has been reproduced with:
CPU: IMX6D5EYM10AD or MCIMX6D5EYM10AE.
SW: U-Boot 2019.07 and kernel 4.19.40.
CPU: HP Proliant Microserver Gen8.
SW: Linux version 4.2.3-300.fc23.x86_64
In this situation there will be error bit for MMF active yet the
CERR equals EHCI_TUNE_CERR + halt. Existing implementation
interprets this as a stall [1] (chapter 8.4.5).
The possible conditions when the MMF will be active + halt
can be found from [2] (Table 4-13).
Fix for the issue is to check whether MMF is active and PID Code is
IN before checking for the stall. If these conditions are true then
it is not a stall.
What happens after the fix is that when disconnecting a hub with
attached device(s) the situation is not interpret as a stall.
[1] [https://www.usb.org/document-library/usb-20-specification, usb_20.pdf]
[2] [https://www.intel.com/content/dam/www/public/us/en/documents/
technical-specifications/ehci-specification-for-usb.pdf]
Signed-off-by: Erkka Talvitie <erkka.talvitie@vincit.fi>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ef70941d5f349767f19c0ed26b0dd9eed8ad81bb.1576050523.git.erkka.talvitie@vincit.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 057d476fff upstream.
A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.
When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.
If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.
Example case:
usb_runtime_suspend() # because all ports still show suspended U3
usb_suspend_both()
hub_suspend(); # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
handle_port_status()
clear bus_state->port_remote_wakeup
usb_wakeup_notification()
sets hub->wakeup_bits;
kick_hub_wq()
<== END INTERRUPT
hcd_bus_suspend()
xhci_bus_suspend() # success as port_remote_wakeup bits cleared
Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.
Issue rootcaused by Chiasheng Lee
Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bd82873f23 ]
spin_unlock_irqrestore() might be called with stale flags after
reading port status, possibly restoring interrupts to a incorrect
state.
If a usb2 port just finished resuming while the port status is read
the spin lock will be temporary released and re-acquired in a separate
function. The flags parameter is passed as value instead of a pointer,
not updating flags properly before the final spin_unlock_irqrestore()
is called.
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 8b3d45705e ("usb: Fix xHCI host issues on remote wakeup.")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7ff1116280 upstream.
xhci driver claims it needs XHCI_TRUST_TX_LENGTH quirk for both
Broadcom/Cavium and a Renesas xHC controllers.
The quirk was inteded for handling false "success" complete event for
transfers that had data left untransferred.
These transfers should complete with "short packet" events instead.
In these two new cases the false "success" completion is reported
after a "short packet" if the TD consists of several TRBs.
xHCI specs 4.10.1.1.2 say remaining TRBs should report "short packet"
as well after the first short packet in a TD, but this issue seems so
common it doesn't make sense to add the quirk for all vendors.
Turn these events into short packets automatically instead.
This gets rid of the "The WARN Successful completion on short TX for
slot 1 ep 1: needs XHCI_TRUST_TX_LENGTH quirk" warning in many cases.
Cc: <stable@vger.kernel.org>
Reported-by: Eli Billauer <eli.billauer@gmail.com>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Eli Billauer <eli.billauer@gmail.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8dc7623bf6 ]
PHY model is being used on omap5 platforms even if port mode
is not OMAP_EHCI_PORT_MODE_PHY. So don't guess if PHY is required
or not based on PHY mode.
If PHY is provided in device tree, it must be required. So, if
devm_usb_get_phy_by_phandle() gives us an error code other
than -ENODEV (no PHY) then error out.
This fixes USB Ethernet on omap5-uevm if PHY happens to
probe after EHCI thus causing a -EPROBE_DEFER.
Cc: Johan Hovold <johan@kernel.org>
Cc: Ladislav Michl <ladis@linux-mips.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d5501d5c29 upstream.
It looks like some of the xhci debug code is passing u32 to functions
directly from __le32/__le64 fields.
Fix this by using le{32,64}_to_cpu() on these to fix the following
sparse warnings;
xhci-debugfs.c:205:62: warning: incorrect type in argument 1 (different base types)
xhci-debugfs.c:205:62: expected unsigned int [usertype] field0
xhci-debugfs.c:205:62: got restricted __le32
xhci-debugfs.c:206:62: warning: incorrect type in argument 2 (different base types)
xhci-debugfs.c:206:62: expected unsigned int [usertype] field1
xhci-debugfs.c:206:62: got restricted __le32
...
[Trim down commit message, sparse warnings were similar -Mathias]
Cc: <stable@vger.kernel.org> # 4.15+
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8de66b0e6a upstream.
The system can hit a deadlock if an xhci adapter breaks while initializing.
The deadlock is between two threads: thread 1 is tearing down the
adapter and is stuck in usb_unlocked_disable_lpm waiting to lock the
hcd->handwidth_mutex. Thread 2 is holding this mutex (while still trying
to add a usb device), but is stuck in xhci_endpoint_reset waiting for a
stop or config command to complete. A reboot is required to resolve.
It turns out when calling xhci_queue_stop_endpoint and
xhci_queue_configure_endpoint in xhci_endpoint_reset, the return code is
not checked for errors. If the timing is right and the adapter dies just
before either of these commands get issued, we hang indefinitely waiting
for a completion on a command that didn't get issued.
This wasn't a problem before the following fix because we didn't send
commands in xhci_endpoint_reset:
commit f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
With the patch I am submitting, a duration test which breaks adapters
during initialization (and which deadlocks with the standard kernel) runs
without issue.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Torez Smith <torez@redhat.com>
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Signed-off-by: Torez Smith <torez@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-7-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c03101ff4f upstream.
The check printing out the "WARN Wrong bounce buffer write length:"
uses incorrect values when comparing bytes written from scatterlist
to bounce buffer. Actual copied lengths are fine.
The used seg->bounce_len will be set to equal new_buf_len a few lines later
in the code, but is incorrect when doing the comparison.
The patch which added this false warning was backported to 4.8+ kernels
so this should be backported as far as well.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 597c56e372 ("xhci: update bounce buffer with correct sg num")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 993cc87534 ]
The Falcon microcontroller that runs the XUSB firmware and which is
responsible for exposing the XHCI interface can address only 40 bits of
memory. Typically that's not a problem because Tegra devices don't have
enough system memory to exceed those 40 bits.
However, if the ARM SMMU is enable on Tegra186 and later, the addresses
passed to the XUSB controller can be anywhere in the 48-bit IOV address
space of the ARM SMMU. Since the DMA/IOMMU API starts allocating from
the top of the IOVA space, the Falcon microcontroller is not able to
load the firmware successfully.
Fix this by setting the DMA mask to 40 bits, which will force the DMA
API to map the buffer for the firmware to an IOVA that is addressable by
the Falcon.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1566989697-13049-1-git-send-email-nkristam@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a349b95d7c upstream.
This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.
[ 34.851754] usb 2-1: USB disconnect, device number 2
[ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[ 35.187886] Workqueue: usb_hub_wq hub_event
[ 35.192063] Call trace:
[ 35.194509] dump_backtrace+0x0/0x150
[ 35.198165] show_stack+0x14/0x20
[ 35.201475] dump_stack+0xa0/0xc4
[ 35.204785] __report_bad_irq+0x34/0xe8
[ 35.208614] note_interrupt+0x2cc/0x318
[ 35.212446] handle_irq_event_percpu+0x5c/0x88
[ 35.216883] handle_irq_event+0x48/0x78
[ 35.220712] handle_fasteoi_irq+0xb4/0x188
[ 35.224802] generic_handle_irq+0x24/0x38
[ 35.228804] __handle_domain_irq+0x5c/0xb0
[ 35.232893] gic_handle_irq+0x58/0xa8
[ 35.236548] el1_irq+0xb8/0x180
[ 35.239681] __do_softirq+0x94/0x23c
[ 35.243253] irq_exit+0xd0/0xd8
[ 35.246387] __handle_domain_irq+0x60/0xb0
[ 35.250475] gic_handle_irq+0x58/0xa8
[ 35.254130] el1_irq+0xb8/0x180
[ 35.257268] kernfs_find_ns+0x5c/0x120
[ 35.261010] kernfs_find_and_get_ns+0x3c/0x60
[ 35.265361] sysfs_unmerge_group+0x20/0x68
[ 35.269454] dpm_sysfs_remove+0x2c/0x68
[ 35.273284] device_del+0x80/0x370
[ 35.276683] hid_destroy_device+0x28/0x60
[ 35.280686] usbhid_disconnect+0x4c/0x80
[ 35.284602] usb_unbind_interface+0x6c/0x268
[ 35.288867] device_release_driver_internal+0xe4/0x1b0
[ 35.293998] device_release_driver+0x14/0x20
[ 35.298261] bus_remove_device+0x110/0x128
[ 35.302350] device_del+0x148/0x370
[ 35.305832] usb_disable_device+0x8c/0x1d0
[ 35.309921] usb_disconnect+0xc8/0x2d0
[ 35.313663] hub_event+0x6e0/0x1128
[ 35.317146] process_one_work+0x1e0/0x320
[ 35.321148] worker_thread+0x40/0x450
[ 35.324805] kthread+0x124/0x128
[ 35.328027] ret_from_fork+0x10/0x18
[ 35.331594] handlers:
[ 35.333862] [<0000000079300c1d>] usb_hcd_irq
[ 35.338126] [<0000000079300c1d>] usb_hcd_irq
[ 35.342389] Disabling IRQ #156
ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
ohci_irq()
-> process_done_list()
-> takeback_td()
-> start_ed_unlink()
So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:
/* interrupt for some other device? */
if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
return IRQ_NOTMINE;
To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().
This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 783bda5e41 upstream.
When a USB device is connected to the host controller and
the system enters suspend, the following error happens
in xhci_suspend():
xhci-hcd ee000000.usb: WARN: xHC CMD_RUN timeout
Since the firmware/internal CPU control the USBSTS.STS_HALT
and the process speed is down when the roothub port enters U3,
long delay for the handshake of STS_HALT is neeed in xhci_suspend().
So, this patch adds to set the XHCI_SLOW_SUSPEND.
Fixes: 435cc1138e ("usb: host: xhci-plat: set resume_quirk() for R-Car controllers")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1564734815-17964-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3dccdaade upstream.
The AMD PLL USB quirk is incorrectly enabled on newer Ryzen
chipsets. The logic in usb_amd_find_chipset_info currently checks
for unaffected chipsets rather than affected ones. This broke
once a new chipset was added in e788787ef. It makes more sense
to reverse the logic so it won't need to be updated as new
chipsets are added. Note that the core of the workaround in
usb_amd_quirk_pll does correctly check the chipset.
Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Fixes: e788787ef4 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8c3b71808 upstream.
A USB3 device needs to be reset and re-enumarated if the port it
connects to goes to a error state, with link state inactive.
There is no use in trying to recover failed transactions by resetting
endpoints at this stage. Tests show that in rare cases, after multiple
endpoint resets of a roothub port the whole host controller might stop
completely.
Several retries to recover from transaction error can happen as
it can take a long time before the hub thread discovers the USB3
port error and inactive link.
We can't reliably detect the port error from slot or endpoint context
due to a limitation in xhci, see xhci specs section 4.8.3:
"There are several cases where the EP State field in the Output
Endpoint Context may not reflect the current state of an endpoint"
and
"Software should maintain an accurate value for EP State, by tracking it
with an internal variable that is driven by Events and Doorbell accesses"
Same appears to be true for slot state.
set a flag to the corresponding slot if a USB3 roothub port link goes
inactive to prevent both queueing new URBs and resetting endpoints.
Reported-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Tested-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddd57980a0 upstream.
USB 3.2 capability in a host can be detected from the
xHCI Supported Protocol Capability major and minor revision fields.
If major is 0x3 and minor 0x20 then the host is USB 3.2 capable.
For USB 3.2 capable hosts set the root hub lane count to 2.
The Major Revision and Minor Revision fields contain a BCD version number.
The value of the Major Revision field is JJh and the value of the Minor
Revision field is MNh for version JJ.M.N, where JJ = major revision number,
M - minor version number, N = sub-minor version number,
e.g. version 3.1 is represented with a value of 0310h.
Also fix the extra whitespace printed out when announcing regular
SuperSpeed hosts.
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5bce256f0b ]
In xhci_debugfs_create_slot(), kzalloc() can fail and
dev->debugfs_private will be NULL.
In xhci_debugfs_create_endpoint(), dev->debugfs_private is used without
any null-pointer check, and can cause a null pointer dereference.
To fix this bug, a null-pointer check is added in
xhci_debugfs_create_endpoint().
This bug is found by a runtime fuzzing tool named FIZZER written by us.
[subjet line change change, add potential -Mathais]
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f7fac17ca9 upstream.
Xhci_handshake() implements the algorithm already captured by
readl_poll_timeout_atomic(). Convert the former to use the latter to
avoid repetition.
Turned out this patch also fixes a bug on the AMD Stoneyridge platform
where usleep(1) sometimes takes over 10ms.
This means a 5 second timeout can easily take over 15 seconds which will
trigger the watchdog and reboot the system.
[Add info about patch fixing a bug to commit message -Mathias]
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Raul E Rangel <rrangel@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1a145a3ed upstream.
Commit 597c56e372 ("xhci: update bounce buffer with correct sg num")
caused the following build warnings:
drivers/usb/host/xhci-ring.c:676:19: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'size_t {aka unsigned int}' [-Wformat=]
Use %zu for printing size_t type in order to fix the warnings.
Fixes: 597c56e372 ("xhci: update bounce buffer with correct sg num")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 597c56e372 upstream.
This change fixes a data corruption issue occurred on USB hard disk for
the case that bounce buffer is used during transferring data.
While updating data between sg list and bounce buffer, current
implementation passes mapped sg number (urb->num_mapped_sgs) to
sg_pcopy_from_buffer() and sg_pcopy_to_buffer(). This causes data
not get copied if target buffer is located in the elements after
mapped sg elements. This change passes sg number for full list to
fix issue.
Besides, for copying data from bounce buffer, calling dma_unmap_single()
on the bounce buffer before copying data to sg list can avoid cache issue.
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d92f2c59cc upstream.
Commit 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.
Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.
Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).
Original patch was sent to stable, this one should go there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8867ea2621 upstream.
The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled
move the memory cleanup outside the spinlock
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cbcf59693 upstream.
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.
Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.
Add U1 and U2 to the possible link states when checking for finished
port resume.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c85400f886 upstream.
The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may
be concurrently executed.
The two functions both access a possible shared variable "hep->hcpriv".
This shared variable is freed by r8a66597_endpoint_disable() via the
call path:
r8a66597_endpoint_disable
kfree(hep->hcpriv) (line 1995 in Linux-4.19)
This variable is read by r8a66597_urb_enqueue() via the call path:
r8a66597_urb_enqueue
spin_lock_irqsave(&r8a66597->lock)
init_pipe_info
enable_r8a66597_pipe
pipe = hep->hcpriv (line 802 in Linux-4.19)
The read operation is protected by a spinlock, but the free operation
is not protected by this spinlock, thus a concurrency use-after-free bug
may occur.
To fix this bug, the spin-lock and spin-unlock function calls in
r8a66597_endpoint_disable() are moved to protect the free operation.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2419f30a4a upstream.
As commented in the struct's definition there shouldn't be anything
underneath its 'priv[0]' member as it would break some macros.
The patch converts the broken_suspend into a bit-field and relocates it
next to to the rest of bit-fields.
Fixes: a7d57abcc8 ("xhci: workaround CSS timeout on AMD SNPS 3.0 xHC")
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45f750c16c upstream.
The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0472bf06c6 upstream.
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7d57abcc8 upstream.
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f31a67f01 upstream.
USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11644a7659 upstream.
Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.
Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.
Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5baeaeabc upstream.
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 958c0bd860 upstream.
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1245374e9b upstream.
At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing NULL pointer dereference.
Check if xhci->shared_hcd is still valid before handing USB3 port events
Cc: <stable@vger.kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
