[ Upstream commit b08134eb25 ]
After initial start-up, the driver triggers ATI (calibration) with
the newly loaded register configuration in place. Next, the driver
polls a register field to ensure ATI completed in a timely fashion
and that the device is ready to sense.
However, communicating with the device over I2C while ATI is under-
way may induce noise in the device and cause ATI to fail. As such,
the vendor recommends not to poll the device during ATI.
To solve this problem, let the device naturally signal to the host
that ATI is complete by way of an interrupt. A completion prevents
the device from successfully probing until this happens.
As an added benefit, initial switch states are now reported in the
interrupt handler at the same time ATI status is checked. As such,
duplicate code that reports initial switch states has been removed
from iqs269_input_init().
The former logic that scaled ATI timeout and filter settling delay
is not carried forward with the new implementation, as it produces
overly conservative delays at the lower clock rate.
Rather, a single timeout that covers both clock rates is used. The
filter settling delay does not happen to be necessary and has been
removed as well.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7RtB2T7AF9rYMjK@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18ab69c8ca ]
Polling the device while it transitions from automatic to manual
power mode switching may keep the device from actually finishing
the transition. The process appears to time out depending on the
polling rate and the device's core clock frequency.
This is ultimately unnecessary in the first place; instead it is
sufficient to write the desired mode during initialization, then
disable automatic switching at suspend. This eliminates the need
to ensure the device is prepared for a manual change and removes
the 'suspend_mode' variable.
Similarly, polling the device while it transitions from one mode
to another under manual control may time out as well. This added
step does not appear to be necessary either, so drop it.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs+eEXlRw4Vq57@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13f82ca387 ]
Controllers that report pressure (e.g. ADS7846) use 5 commands and the
correct sequence is READ_X, READ_Y, READ_Z1, READ_Z2, PWRDOWN.
Controllers that don't report pressure (e.g. ADS7845/ADS7843) use only 3
commands and the correct sequence should be READ_X, READ_Y, PWRDOWN. But
the sequence sent was incorrect: READ_X, READ_Y, READ_Z1.
Fix this by setting the third (and last) command to PWRDOWN.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Signed-off-by: Luca Ellero <l.ellero@asem.it>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230126105227.47648-3-l.ellero@asem.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e023cc4abd ]
The time the device takes to deassert its RDY output following an
I2C stop condition scales with the core clock frequency.
To prevent level-triggered interrupts from being reasserted after
the interrupt handler returns, increase the time before returning
to account for the worst-case delay (~140 us) plus margin.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs484ypy4dab5G@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3689abfc4e ]
Unless it is being done as part of servicing a soft reset interrupt,
configuring channels on-the-fly (as is the case when writing to the
ati_trigger attribute) may cause GPIO3 (which reflects the state of
touch for a selected channel) to be inadvertently asserted.
To solve this problem, follow the vendor's recommendation and write
all channel configuration as well as the REDO_ATI register field as
part of a single block write. This ensures the device has been told
to re-calibrate itself following an I2C stop condition, after which
sensing resumes and GPIO3 may be asserted.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/Y7Rs8GyV7g0nF5Yy@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59bc9cb3b8 ]
Each call to device/fwnode_get_named_child_node() must be matched
with a call to fwnode_handle_put() once the corresponding node is
no longer in use. This ensures a reference count remains balanced
in the case of dynamic device tree support.
Currently, the driver does not call fwnode_handle_put() on nested
event nodes. This patch solves this problem by adding the missing
instances of fwnode_handle_put().
As part of this change, the logic which parses each channel's key
code is gently refactored in order to reduce the number of places
from which fwnode_handle_put() is called.
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/Y7Rsx68k/gvDVXAt@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4255447ad34c5c3785fcdcf76cfa0271d6e5ed39 ]
Another Fujitsu-related patch.
In the initial boot stage the integrated keyboard of Fujitsu Lifebook U728
refuses to work and it's not possible to type for example a dm-crypt
passphrase without the help of an external keyboard.
i8042.nomux kernel parameter resolves this issue but using that a PS/2
mouse is detected. This input device is unused even when the i2c-hid-acpi
kernel module is blacklisted making the integrated ELAN touchpad
(04F3:3092) not working at all.
So this notebook uses a hid-over-i2c touchpad which is managed by the
i2c_designware input driver. Since you can't find a PS/2 mouse port on this
computer and you can't connect a PS/2 mouse to it even with an official
port replicator I think it's safe to not use the PS/2 mouse port at all.
Signed-off-by: Szilard Fabian <szfabian@bluemarch.art>
Link: https://lore.kernel.org/r/20240103014717.127307-2-szfabian@bluemarch.art
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80441f76ee67002437db61f3b317ed80cce085d2 ]
The Lenovo Legion Go is a handheld gaming system, similar to a Steam Deck.
It has a gamepad (including rear paddles), 3 gyroscopes, a trackpad,
volume buttons, a power button, and 2 LED ring lights.
The Legion Go firmware presents these controls as a USB hub with various
devices attached. In its default state, the gamepad is presented as an
Xbox controller connected to this hub. (By holding a combination of
buttons, it can be changed to use the older DirectInput API.)
This patch teaches the existing Xbox controller module `xpad` to bind to
the controller in the Legion Go, which enables support for the:
- directional pad,
- analog sticks (including clicks),
- X, Y, A, B,
- start and select (or menu and capture),
- shoulder buttons, and
- rumble.
The trackpad, touchscreen, volume controls, and power button are already
supported via existing kernel modules. Two of the face buttons, the
gyroscopes, rear paddles, and LEDs are not.
After this patch lands, the Legion Go will be mostly functional in Linux,
out-of-the-box. The various components of the USB hub can be synthesized
into a single logical controller (including the additional buttons) in
userspace with [Handheld Daemon](https://github.com/hhd-dev/hhd), which
makes the Go fully functional.
Signed-off-by: Brenton Simpson <appsforartists@google.com>
Link: https://lore.kernel.org/r/20240118183546.418064-1-appsforartists@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a60e6c3918d20848906ffcdfcf72ca6a8cfbcf2e upstream.
When closing the laptop lid with an external screen connected, the mouse
pointer has a constant movement to the lower right corner. Opening the
lid again stops this movement, but after that the touchpad does no longer
register clicks.
The touchpad is connected both via i2c-hid and PS/2, the predecessor of
this device (NS70MU) has the same layout in this regard and also strange
behaviour caused by the psmouse and the i2c-hid driver fighting over
touchpad control. This fix is reusing the same workaround by just
disabling the PS/2 aux port, that is only used by the touchpad, to give the
i2c-hid driver the lone control over the touchpad.
v2: Rebased on current master
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231205163602.16106-1-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea3715941a9b7d816a1e9096ac0577900af2a69e upstream.
This add a mapping for the airplane mode button on the TUXEDO Pulse Gen3.
While it is physically a key it behaves more like a switch, sending a key
down on first press and a key up on 2nd press. Therefor the switch event
is used here. Besides this behaviour it uses the HID usage-id 0xc6
(Wireless Radio Button) and not 0xc8 (Wireless Radio Slider Switch), but
since neither 0xc6 nor 0xc8 are currently implemented at all in
soc_button_array this not to standard behaviour is not put behind a quirk
for the moment.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://lore.kernel.org/r/20231215171718.80229-1-wse@tuxedocomputers.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59b6a747e2d39227ac2325c5e29d6ab3bb070c2a ]
Check the return value of i2c_add_adapter. Static analysis revealed that
the function did not properly handle potential failures of
i2c_add_adapter, which could lead to partial initialization of the I2C
adapter and unstable operation.
Signed-off-by: Haoran Liu <liuhaoran14@163.com>
Link: https://lore.kernel.org/r/20231203164653.38983-1-liuhaoran14@163.com
Fixes: d7535ffa42 ("Input: driver for microcontroller keys on the iPaq h3xxx")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5030b2fe6a ]
Touch controllers need some time after receiving reset command for the
firmware to finish re-initializing and be ready to respond to commands
from the host. The driver already had handling for the post-reset delay
for I2C and SPI transports, this change adds the handling to
SMBus-connected devices.
SMBus devices are peculiar because they implement legacy PS/2
compatibility mode, so reset is actually issued by psmouse driver on the
associated serio port, after which the control is passed to the RMI4
driver with SMBus companion device.
Note that originally the delay was added to psmouse driver in
92e24e0e57 ("Input: psmouse - add delay when deactivating for SMBus
mode"), but that resulted in an unwanted delay in "fast" reconnect
handler for the serio port, so it was decided to revert the patch and
have the delay being handled in the RMI4 driver, similar to the other
transports.
Tested-by: Jeffery Miller <jefferymiller@google.com>
Link: https://lore.kernel.org/r/ZR1yUFJ8a9Zt606N@penguin
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 423622a90a upstream.
Add a special case for gpio_count == 1 && gpio_int_idx == 0 to
goodix_add_acpi_gpio_mappings().
It seems that on newer x86/ACPI devices the reset and irq GPIOs are no
longer listed as GPIO resources instead there is only 1 GpioInt resource
and _PS0 does the whole reset sequence for us.
This means that we must call acpi_device_fix_up_power() on these devices
to ensure that the chip is reset before we try to use it.
This part was already fixed in commit 3de93e6ed2 ("Input: goodix - call
acpi_device_fix_up_power() in some cases") by adding a call to
acpi_device_fix_up_power() to the generic "Unexpected ACPI resources"
catch all.
But it turns out that this case on some hw needs some more special
handling. Specifically the firmware may bootup with the IRQ pin in
output mode. The reset sequence from ACPI _PS0 (executed by
acpi_device_fix_up_power()) should put the pin in input mode,
but the GPIO subsystem has cached the direction at bootup, causing
request_irq() to fail due to gpiochip_lock_as_irq() failure:
[ 9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0
[ 9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060
[ 9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8
[ 9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ
[ 9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio
[ 9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5
Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0
which adds an ACPI GPIO lookup table for the int GPIO even though we cannot
use it for reset purposes (as there is no reset GPIO).
Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call
succeed, which will explicitly set the direction to input fixing the issue.
Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since
there is only 1 GPIO in the ACPI resources the reset entry in that
lookup table will amount to a no-op.
Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80f39e1c27 upstream.
In the initial boot stage the integrated keyboard of Fujitsu Lifebook E5411
refuses to work and it's not possible to type for example a dm-crypt
passphrase without the help of an external keyboard.
i8042.nomux kernel parameter resolves this issue but using that a PS/2
mouse is detected. This input device is unused even when the i2c-hid-acpi
kernel module is blacklisted making the integrated ELAN touchpad
(04F3:308A) not working at all.
Since the integrated touchpad is managed by the i2c_designware input
driver in the Linux kernel and you can't find a PS/2 mouse port on the
computer I think it's safe to not use the PS/2 mouse port at all.
Signed-off-by: Szilard Fabian <szfabian@bluemarch.art>
Link: https://lore.kernel.org/r/20231004011749.101789-1-szfabian@bluemarch.art
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e2cb5cc822 upstream.
When the SMBus connection is attempted psmouse_smbus_init() sets
the fast_reconnect pointer to psmouse_smbus_reconnecti(). If SMBus
initialization fails, elantech_setup_ps2() and synaptics_init_ps2() will
fallback to PS/2 mode, replacing the psmouse private data. This can cause
issues on resume, since psmouse_smbus_reconnect() expects to find an
instance of struct psmouse_smbus_dev in psmouse->private.
The issue was uncovered when in 92e24e0e57 ("Input: psmouse - add
delay when deactivating for SMBus mode") psmouse_smbus_reconnect()
started attempting to use more of the data structure. The commit was
since reverted, not because it was at fault, but because there was found
a better way of doing what it was attempting to do.
Fix the problem by resetting the fast_reconnect pointer in psmouse
structure in elantech_setup_ps2() and synaptics_init_ps2() when the PS/2
mode is used.
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Tested-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jeffery Miller <jefferymiller@google.com>
Fixes: bf232e460a ("Input: psmouse-smbus - allow to control psmouse_deactivate")
Link: https://lore.kernel.org/r/20231005002249.554877-1-jefferymiller@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eb09074bdb ]
The touchpad of this device is both connected via PS/2 and i2c. This causes
strange behavior when both driver fight for control. The easy fix is to
prevent the PS/2 driver from accessing the mouse port as the full feature
set of the touchpad is only supported in the i2c interface anyway.
The strange behavior in this case is, that when an external screen is
connected and the notebook is closed, the pointer on the external screen is
moving to the lower right corner. When the notebook is opened again, this
movement stops, but the touchpad clicks are unresponsive afterwards until
reboot.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230607173331.851192-1-wse@tuxedocomputers.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20a99a291d ]
Some devices have a wrong entry in their button array which points to
a GPIO which is required in another driver, so soc_button_array must
not claim it.
A specific example of this is the Lenovo Yoga Book X90F / X90L,
where the PNP0C40 home button entry points to a GPIO which is not
a home button and which is required by the lenovo-yogabook driver.
Add a DMI quirk table which can specify an ACPI GPIO resource index which
should be skipped; and add an entry for the Lenovo Yoga Book X90F / X90L
to this new DMI quirk table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230414072116.4497-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit feee70f456 upstream.
While doing my research to improve the xpad device names I noticed
that the 1532:0037 VID/PID seems to be used by the DeathAdder 2013,
so that Razer Sabertooth instance looked wrong and very suspect to
me. I didn't see any mention in the official drivers, either.
After doing more research, it turns out that the xpad list
is used by many other projects (like Steam) as-is [1], this
issue was reported [2] and Valve/Sam Lantinga fixed it [3]:
[1]: dcc5eef0e2/src/joystick/controller_type.h (L251)
[2]: https://steamcommunity.com/app/353380/discussions/0/1743392486228754770/
[3]: https://hg.libsdl.org/SDL/rev/29809f6f0271
(With multiple Internet users reporting similar issues, not linked here)
After not being able to find the correct VID/PID combination anywhere
on the Internet and not receiving any reply from Razer support I did
some additional detective work, it seems like it presents itself as
"Razer Sabertooth Gaming Controller (XBOX360)", code 1689:FE00.
Leaving us with this:
* Razer Sabertooth (1689:fe00)
* Razer Sabertooth Elite (24c6:5d04)
* Razer DeathAdder 2013 (1532:0037) [note: not a gamepad]
So, to sum things up; remove this conflicting/duplicate entry:
{ 0x1532, 0x0037, "Razer Sabertooth", 0, XTYPE_XBOX360 },
As the real/correct one is already present there, even if
the Internet as a whole insists on presenting it as the
Razer Sabertooth Elite, which (by all accounts) is not:
{ 0x1689, 0xfe00, "Razer Sabertooth", 0, XTYPE_XBOX360 },
Actual change in SDL2 referencing this kernel issue:
e5e5416975
For more information of the device, take a look here:
https://github.com/xboxdrv/xboxdrv/pull/59
You can see a lsusb dump here: https://github.com/xboxdrv/xboxdrv/files/76581/Qa6dBcrv.txt
Fixes: f554f619b7 ("Input: xpad - sync device IDs with xboxdrv")
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/5c12dbdb-5774-fc68-5c58-ca596383663e@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a0432bab6 upstream.
The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen
with 9 bytes touch reports for its touch keyboard as the already supported
Windows Lenovo Yoga Book X91F/L, add a DMI match for this to
the nine_bytes_report DMI table.
When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754ff5060d upstream.
The AlpsPS/2 code previously relied on the assumption that `char` is a
signed type, which was true on x86 platforms (the only place where this
driver is used) before kernel 6.2. However, on 6.2 and later, this
assumption is broken due to the introduction of -funsigned-char as a new
global compiler flag.
Fix this by explicitly specifying the signedness of `char` when sign
extending the values received from the device.
Fixes: f3f33c6776 ("Input: alps - Rushmore and v7 resolution support")
Signed-off-by: msizanoen <msizanoen@qtmlabs.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230320045228.182259-1-msizanoen@qtmlabs.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a85fbd6498 ]
As can be seen in elants_i2c_power_off(), we want the reset GPIO
asserted when power is off. The reset GPIO is active low so we need
the reset line logic low when power is off to avoid leakage.
We have a problem, though, at probe time. At probe time we haven't
powered the regulators on yet but we have:
devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
While that _looks_ right, it turns out that it's not. The
GPIOD_OUT_LOW doesn't mean to init the GPIO to low. It means init the
GPIO to "not asserted". Since this is an active low GPIO that inits it
to be high.
Let's fix this to properly init the GPIO. Now after both probe and
power off the state of the GPIO is consistent (it's "asserted" or
level low).
Once we fix this, we can see that at power on time we no longer to
assert the reset GPIO as the first thing. The reset GPIO is _always_
asserted before powering on. Let's fix powering on to account for
this.
Fixes: afe10358e4 ("Input: elants_i2c - wire up regulator support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20221117123805.1.I9959ac561dd6e1e8e1ce7085e4de6167b27c574f@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
