In some places in et131x.c, one arm of am if/else statement has braces
and the other not - put braces on both arms where this happens.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checkpatch --strict advises that spinlocks should be described when
defined, seems a good idea so this change does that.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need to use this lock - the tx path is protected by the
networking subsystem xmit_lock, so we don't also need it in
nic_send_packet().
The other use of this spinlock in et1310_enable_phy_coma() to protect
a low power flag makes no sense, so can just be removed.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcb_send_qlock spinlock is unlocked in all three paths at the end of
et131x_tx_timeout(). We can call it once before entering any of the paths,
saving ourselves a few lines of code.
This change puts tcb->count++ outside of the lock, but et131x_tx_timeout()
itself is protected by the tx_global_lock, so this shouldn't matter.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of spinlocks has been halved, from 8 to 4 since this
comment was made, let's see if this is enough.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In nic_rx_pkts(), we check that a multicast packet received (when using
a multicast list) is one that was requested - despite setting the list
up with the hardware. We shouldn't expect to get a mc packet we didn't
ask for, so remove these extra checks.
This also means that the surrounding code can be tiedied up a little.
Tested somewhat with omping, with no adverse effects seen.
Also remove this item from the TODO list.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both these if statements have the same effect when true, so combine
them and save a few lines.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'struct tcb' member 'flags' was only used to collect tx stats, now
we are no longer collecting those particular stats, we no longer
need tcb->flags or the code used to peek into the skb to set it's
value.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From struct ce_stats; unicast_pkts_rcvd, unicast_pkts_xmtd,
multicast_pkts_xmtd, broadcast_pkts_rcvd and broadcast_pkts_xmtd
are not returned or used for anything meaningful - remove the code
that collects them, and the struct members too.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove some fairly useless comments regarding rx/tx _bytes and
_dropped, and use rcvd_pkts_dropped stat value to provide rx_dropped.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory allocation errors do not denote NETDEV_TX_BUSY, simply drop
the packet silently with kfree_skb() and return NETDEV_TX_OK.
Also remove this item from the TODO list.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove et131x_send_packets() and replace the only use in et131x_tx
with the removed function's body.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add counter support for NI USB-6501.
The following functions are introduced:
- ni6501_counter_command()
- ni6501_cnt_insn_config()
- ni6501_cnt_insn_read()
- ni6501_cnt_insn_write()
Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the exported functions in the "comedi_fc" module have been migrated
to the core "comedi" module and renamed, so it is now just a dummy
module. Remove it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "comedi_fc" module was originally written and copyrighted by Frank
Mori Hess, but the functionality has been migrated into the core
"comedi" module. Move the copyright notices over to the affected .c
files in the core comedi module.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "comedi_fc" module contains a few functions useful to Comedi
drivers. Their functionality is being migrated to the core "comedi"
module and renamed to start with the prefix `comedi_`. As part of this
migration, move `cfc_read_array_from_buffer()` into the core comedi
module and rename it to `comedi_read_array_from_buffer()`. Change the
external declaration of `cfc_read_array_from_buffer()` into an inline
function that calls `comedi_read_array_from_buffer()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since `cfc_write_array_to_buffer()` is just an inline function that
calls `comedi_write_array_to_buffer()`, replace calls to the former to
the latter in the "comedi_fc.h" header. This is part of the migration
of functionality from the "comedi_fc" module to the core "comedi"
module.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "comedi_fc" module contains a few functions useful to Comedi
drivers. Their functionality is being migrated to the core "comedi"
module and renamed to start with the prefix `comedi_`. As part of this
migration, move `cfc_write_array_to_buffer()` into the core comedi
module and rename it to `comedi_write_array_to_buffer()`. Change the
external declaration of `cfc_write_array_to_buffer()` into an inline
function that calls `comedi_write_array_to_buffer()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "comedi_fc" module contains a few functions useful to Comedi
drivers. Their functionality is being migrated to the core "comedi"
module and renamed to start with the prefix `comedi_`. As part of this
migration, move `cfc_handle_events()` into the core comedi module and
rename it to `comedi_handle_events()`. Change the external declaration
of `cfc_handle_events()` into an inline function that calls
`comedi_handle_events()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since `cfc_inc_scan_progress()` is just an inline function that calls
`comedi_inc_scan_progress()`, replace calls to the former to the latter
in the "comedi_fc" module. This is part of the migration of
functionality from the "comedi_fc" module to the core "comedi" module.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "comedi_fc" module contains a few functions useful to Comedi
drivers. Their functionality is being migrated to the core "comedi"
module and renamed to start with the prefix `comedi_`. As part of this
migration, move `cfc_inc_scan_progress()` into the core comedi module
and rename it to `comedi_inc_scan_progress()`. Change the external
declaration of `cfc_inc_scan_progress()` into an inline function that
calls `comedi_inc_scan_progress()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since `cfc_bytes_per_scan()` is just an inline function that calls
`comedi_bytes_per_scan()`, replace calls to the former to the latter in
the "comedi_fc" module. This is part of the migration of functionality
from the "comedi_fc" module to the core "comedi" module.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "comedi_fc" module contains a few functions useful to Comedi
drivers. Their functionality is being migrated to the core "comedi"
module and renamed to start with the prefix `comedi_`. As part of this
migration, move `cfc_bytes_per_scan()` into the core comedi module and
rename it to `comedi_bytes_per_scan()`. Change the external declaration
of `cfc_bytes_per_scan()` into an inline function that calls
`comedi_bytes_per_scan()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`apci3120_auto_attach()` first sets `devpriv->us_UseDma` to 1, then sets
it back to 0 if it fails to allocate the DMA buffer. Since `*devpriv`
is initially zeroed out by `comedi_alloc_devpriv()`, change it to only
set `devpriv->us_UseDma` to 1 if the allocation succeeds. Also, don't
bother explicitly initializing `devpriv->b_DmaDoubleBuffer` to 0 as it
is already zeroed out.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use `dma_alloc_coherent()` to allocate the DMA buffers instead of
using `__get_free_pages()` to allocate and `virt_to_bus()` to get the
hardware address. The coherent buffers are fairly small - at most 4
pages (although there are two of them). Use of `virt_to_bus()` is
discouraged.
Note: `struct addi_private` is used by some other ADDI-DATA drivers as
well, but this is the only one using the affected members.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last parameter of `__get_free_pages()` is log2 (the 'order') of the
number of pages to be allocated. This driver seems to think it is the
linear number of pages, so `apci3120_auto_attach()` first tries to allocate
16 pages, but only uses 4 of them, setting the buffer size to PAGE_SIZE
multiplied by the 'order'. If the allocation fails, it tries
progressively smaller orders, down to 0. If the allocation at order 0
succeeds, the buffer size is set to 0, which is likely to cause
problems.
Set the buffer size to `PAGE_SIZE` shifted left by the allocation order.
Since the maximum buffer size previously used was 4, start with an
allocation order of 2 instead of 4. Rename the `ui_DmaBufferPages` member of
`struct addi_private` to `ui_DmaBufferPageOrder` and rename the `pages`
local variable to `order` to make it clearer what it is.
Note: `struct addi_private` is used by some other ADDI-DATA drivers as
well, but this is the only one using the affected members.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`apci3120_auto_attach()` tries to allocate two DMA buffers but may
allocate a single buffer or none at all. If it fails to allocate the
first buffer, it still tries to allocate the second buffer, even though
it won't be used. Change it to not bother trying to allocate the second
buffer if the first one fails.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use `dma_alloc_coherent()` to allocate the DMA buffers instead of
using `__get_free_pages()` to allocate and `virt_to_bus()` to get the
hardware address. The coherent buffers are fairly small - at most 4
pages (although there are two of them). Use of `virt_to_bus()` is
discouraged.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last parameter of `__get_free_pages()` is log2 (the 'order') of the
number of pages to be allocated. This driver seems to think it is the
linear number of pages, so `pci9118_alloc_dma()` first tries to allocate
16 pages, but only uses 4 of them, setting the buffer size to PAGE_SIZE
multiplied by the 'order'. If the allocation fails, it tries
progressively smaller orders, down to 0. If the allocation at order 0
succeeds, the buffer size is set to 0, which is likely to cause
problems.
Set the buffer size to `PAGE_SIZE` shifted left by the allocation order.
Since the maximum buffer size previously used was 4, start with an
allocation order of 2 instead of 4. Rename the `pages` member of
`struct pci9118_dmabuf` (and the local variable in
`pci9118_alloc_dma()`) to `order` to make it clearer what it is.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`pci9118_alloc_dma()` tries to allocate two DMA buffers but may allocate
a single buffer or none at all. If it fails to allocate the first
buffer, it still tries to allocate the second buffer, even though it
won't be used. Change it to not bother trying to allocate the second
buffer if the first one fails.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
->u.generic_elem.len is a user controlled number between 0-255. We
should limit it to avoid memory corruption.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan writes:
First round of IIO fixes for the 3.17 cycle.
* Fix an overwritten error return that can prevent deferred probing when
using of_iio_channel_get_by_name
* A series that deals with an incorrect reference count when the default
trigger is set within the main probe routine for a driver. Can result
in a double free if the trigger is changed.
* Fix a buglet with xilinx-xadc concerning setup of the address for an
aux channel.
* At91 adc driver could sometimes get a touchscreen reading rather than
the intended adc channel. This is fixed by using the channel data register
instead.
* Fix some ST magnetometer gain values that differ in production parts from
the prerelease ones used for driver development.
Jonathan writes:
Second round of new IIO drivers, features and cleanups for the 3.18 cycle.
New drivers and part support
* Bosch bmg160 Gyroscope driver
* Dyna-Image al3320a ambient light sensor driver
* Bosh bmi055 gyroscope part driver (accelerometer part supported by bmc150)
* isl29018 - add support for isl29023 and isl29035
* kxcjk-1013 - add support for kxcj9-1008 and kxtj2-1009
* bmc150 - additional part support (BMI055 accelerometer part, BMA255,
BMA222E, BMA250E and BMA280). Different resolutions but otherwise similar
parts.
* bma180 - add BMA250 (note different from the BMA250E support above despite
the naming). A lot of driver reworking lead up to this - described below.
New features
* kxcjk1013 - add threshold event support.
* rockchip - document DT bindings.
* isl29018 - ACPI support
* bma180 - enable use without IRQ
Cleanups
* Tree wide - drop owner field assignment if using the module_platform_driver
helper as that assigns it anyway.
* kxcjk1013 - drop a redundant assignment of the current range and fix a
a defined but not used warning.
* inv_mpu6050 - Remove an unnecessary cast form a void pointer.
* rockchip - drop and unused variable.
* at91_adc - make a local function static.
* st-sensors-core - correctly handle an error in setting in
st_sensors_set_drdy_int_pin
* isl29018 - typo fix
* bmc150 - fix incorrect scale value for 16G range (Driver new this cycle)
* bmc150 - fix issues when CONFIG_PM_RUNTIME not set (Driver new this cycle)
* ad7606 - line length tidy up.
* bmg160 - set power state only if PM_RUNTIME is defined.
* ak8975 - fix some unnecessary casting between char * and const char *
* bma180 - prefix remaining bits and bobs with bma180_ and ensure consistent.
- use a bool instead of an int for state (as its either on or off).
- expose the temperature channel
- statically allocate buffers to avoid need for update_scan_mode
callback.
- refactor to allow futher chip variants including support for part
specific config and disable code + different resolutions.
This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.
The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.
Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.
My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.
This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
