This patch and the following two patches add support for link flap avoidance
by maintaining the link on power down. This feature is required for
management capable devices to have the management connection
uninterrupted on driver reload, reboot and interface up/down.
The other pros of this feature are
- It speeds up boot up time by several seconds as DHCP addresses can be
acquired faster.
- It avoids lengthy Spanning Tree delay.
On powerup the hardware brings up the phy with default settings. If the
link is not up, the management software configures the phy to gigabit
and starts autonegotiate. Subsequently, as long as the link is up, the
driver and management refrain from resetting and/or changing any
configuration that the link depends on.
The LNK_FLAP_AVOID setting is an NVRAM user configurable bit and is
disabled by default. If this setting is enabled, we skip powering down
the phy and resetting it.
A second NVRAM setting is 1G_ON_VAUX_OK (off by default). This adds
support for gigabit link speed when device is on auxiliary power.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user executes certain ethtool commands such as -s, -A, -G, -L,
-r a phy reset or autonegotiate is performed which results in management
traffic being interrupted.
Add a warning in these cases.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code unnecessarily resets the phy when we use ethtool to
change the ring parameters or flow control settings. Remove the phy
reset.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The STM45PE20 pinstrap on 5762 devices supports multiple sizes. So treat
it just like the ST45_USPT and the size will be read from 0xf0 via
tg3_get_nvram_size().
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tg3_setup_copper_phy(), if autonegotiation is disabled, we need to
relink only if the speed or duplex does not match the configured
setting. If flow control does not match, a relink is not necessary as
flow control is not a PHY setting. Later on, we'll call
tg3_setup_flow_ctrl() to set up the MAC to the desired flow control
settings if we're in full duplex mode.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receiving unhandled notifications is most certainly not an error
and should not be logged as one. Knowing that the device sends
notifications we don't handle is useful for developers, but there
is very little a user can do about this. The message is therefore
just annoying noise to most users with devices sending unhandled
notifications like e.g. USB_CDC_NOTIFY_RESPONSE_AVAILABLE
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to prefetch, in the stmmac_rx, the whole
dma_erx descriptor in case of using the extended descriptors.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
recently many new supports have been added in the stmmac driver w/o taking care
about where each new field had to be placed inside the private structure for
guaranteeing the best cache usage.
This is what I wanted in the beginning, so this patch reorganizes all the fields
in order to keep adjacent fields for cache effect.
I have also tried to optimize them by using pahole.
V2: do not abuse with ____cacheline_aligned_in_smp and keep fields that
potentially could stay in the same cache-line for better usage in SMP systems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidies up the code. I have run Linden (and verified with checkpatch)
many part of the driver trying to reorganize some sections respecting the
codying-style rules in the points where it was not done.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch reviews/improves and adds some fixes in the code doc.
Also kernel-doc passes w/o any warnings.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the pcs mode support for SGMII. Even though
SGMII does auto-negotiation with phy, it needs stmmac_init_phy and
stmmac_mdio_register function for initializing phy.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using DT for mdiobus and ethernet-phy requires to know the PHY address, which
is hard to guess if you don't know it. This patch extends of_mdiobus_register
to scan mdiobus for PHYs if reg property of the corresponding node is not set.
This also allows to have phy nodes in SoC DT files where the reg property can
be overwritten in the board file later. To encourage people to finally set the
actual phy address, the mdiobus scan is noisier than required.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell mdio driver uses internal registers that can be clock gated on
some SoCs. This patch just adds optional clock handling, to allow to pass
and enable the corresponding clock.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using module_spi_driver we can eliminate a few lines of boilerplate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the MRF24J40, link-layer acknowledgment request and retry must be
turned on explicitly for each packet. Turn this on in the hardware based
on the FC_ACK_REQ bit being set in the packet.
Also, now that failure to receive an ACK will cause the hardware to report
failure of transmission, change the log level for this failure to debug
level.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
In at86rf230_probe() lp was first set to dev->priv and a few lines later
dev->priv was set to lp again, without changing lp in between. The call
to ieee802154_unregister_device() before err_irq: was unreachable.
Signed-off-by: Sascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a feature is not supported by firmware no need to print an error message.
This surpresses the following harmless message on boot up and ethtool query.
enic: Error 1 devcmd 36
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It served no purpose: we never call it from anywhere in the stack
and the only driver that did implement it (fakehard) merely provided
a dummy value.
There is also considerable doubt whether it would make sense to
even attempt beacon processing at this level in the Linux kernel.
Signed-off-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Octeon SMI/MDIO interfaces can do clause 45 communications, so
implement this in the driver.
Also fix some comment formatting to make it consistent and to comply
with the netdev style.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch bypasses vxlan encapsulation if the destination vxlan
endpoint is a local device.
Changes since v1: added missing check for vxlan_find_vni() failure
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the DCB ETS ops only when supported by the firmware. For older firmware/cards
which don't support ETS, advertize only PFC DCB ops.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added readable description for the DPDP and port sensing device capabilities.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The suggestion as following:
- initial settings or default settings
- rtl_hw_start_xxx. rtl_hw_start_xxx may change some default settings.
- enable tx/rx. This has to be after the above two steps.
- rtl_set_rx_mode. AcceptXXXs have to be enabled after enabling tx/rx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- replace rtl8168g-1.fw with rtl8168g-2.fw which support new method.
- fix PHY power down is useless.
- disable rx early which causes the rx abnormal.
- enable auto fifo.
- set 10M IFG to default value.
- fix the conflict between jumbo frame and flow control.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove useless action PHY_READ_EFUSE, PHY_READ_MAC_BYTE, PHY_WRITE_MAC_BYTE,
PHY_WRITE_ERI_WORD. And define the new action PHY_MDIO_CHG.
PHY_MDIO_CHG is used to modify the mdio operation. By the way, the
firmware could support setting mac ocp.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current settings with rtl_writephy and rtl_readphy.
For the hardware, the settings are same with previous ones. This
make the setting method like the previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some codes are belong to binary codes and should be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix erroneous sock_orphan() leading to crashes and double
kfree_skb() in NFC protocol. From Thierry Escande and Samuel Ortiz.
2) Fix use after free in remain-on-channel mac80211 code, from Johannes
Berg.
3) nf_reset() needs to reset the NF tracing cookie, otherwise we can
leak it from one namespace into another. Fix from Gao Feng and
Patrick McHardy.
4) Fix overflow in channel scanning array of mwifiex driver, from Stone
Piao.
5) Fix loss of link after suspend/shutdown in r8169, from Hayes Wang.
6) Synchronization of unicast address lists to the undelying device
doesn't work because whether to sync is maintained as a boolean
rather than a true count. Fix from Vlad Yasevich.
7) Fix corruption of TSO packets in atl1e by limiting the segmented
packet length. From Hannes Frederic Sowa.
8) Revert bogus AF_UNIX credential passing change and fix the
coalescing issue properly, from Eric W Biederman.
9) Changes of ipv4 address lifetime settings needs to generate a
notification, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
netfilter: don't reset nf_trace in nf_reset()
net: ipv4: notify when address lifetime changes
ixgbe: fix registration order of driver and DCA nofitication
af_unix: If we don't care about credentials coallesce all messages
Revert "af_unix: dont send SCM_CREDENTIAL when dest socket is NULL"
bonding: remove sysfs before removing devices
atl1e: limit gso segment size to prevent generation of wrong ip length fields
net: count hw_addr syncs so that unsync works properly.
r8169: fix auto speed down issue
netfilter: ip6t_NPT: Fix translation for non-multiple of 32 prefix lengths
mwifiex: limit channel number not to overflow memory
NFC: microread: Fix build failure due to a new MEI bus API
iwlwifi: dvm: fix the passive-no-RX workaround
netfilter: nf_conntrack: fix error return code
NFC: llcp: Keep the connected socket parent pointer alive
mac80211: fix idle handling sequence
netfilter: nfnetlink_acct: return -EINVAL if object name is empty
netfilter: nfnetlink_queue: fix error return code in nfnetlink_queue_init()
netfilter: reset nf_trace in nf_reset
mac80211: fix remain-on-channel cancel crash
...
Commit e2eed58b4f ("IB/qib: change QLogic to Intel") moved a firmware
file potentially breaking the ABI.
This patch reverts that aspect of the fix as well as reverting the
firmware name as used in qib.
Reported-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull spi fixes from Mark Brown:
"A bunch of small driver fixes plus a fix for error handling in the
core - nothing too exciting overall."
* tag 'spi-fix-v3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/mpc512x-psc: optionally keep PSC SS asserted across xfer segmensts
spi: Unlock a spinlock before calling into the controller driver.
spi/s3c64xx: modified error interrupt handling and init
spi/bcm63xx: don't disable non enabled clocks in probe error path
spi/bcm63xx: Remove unused variable
spi: slink-tegra20: move runtime pm calls to transfer_one_message
This reverts commit 0ef1594c01.
This patch introduced a few races which cannot be easily fixed with a
small follow-up patch. Furthermore, the SoC with the broken hardware
register, which this patch intended to add support for, can only be used
with device trees, which this driver currently does not support.
[ Here is the discussion that led to this "revert" patch:
https://lkml.org/lkml/2013/4/3/176 ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull fbdev fixes from Tomi Valkeinen:
"Fix uvesafb crash bug and typoed flag name in fbmon's new videomode
code"
* tag 'fbdev-fixes-3.9-rc6' of git://gitorious.org/linux-omap-dss2/linux:
video:uvesafb: Fix dereference NULL pointer code path
fbmon: use VESA_DMT_VSYNC_HIGH to fix typo
