[ Upstream commit e479187748 ]
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
[ 54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error
[ 55.373593] i2c_designware 808622C1:04: controller timed out
[ 55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202745.16777-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65299e8bfb ]
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
[ 0.550596] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vcc33 not found, using dummy regulator
[ 0.551836] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vccio not found, using dummy regulator
[ 0.560932] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.562427] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.595925] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.597974] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.621893] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.622504] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.632650] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (4d 61 69 6e): -121
[ 0.634256] elants_i2c i2c-ELAN0001:00: boot failed: -121
[ 0.699212] elants_i2c i2c-ELAN0001:00: invalid 'hello' packet: 00 00 ff ff
[ 1.630506] elants_i2c i2c-ELAN0001:00: Failed to read fw id: -121
[ 1.645508] elants_i2c i2c-ELAN0001:00: unknown packet 00 00 ff ff
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207759
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202756.16830-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 30b3f68715 upstream.
The touch coordinate register contains the following:
byte 3 byte 2 byte 1
+--------+--------+ +-----------------+ +-----------------+
| | | | | | |
| X[3:0] | Y[3:0] | | Y[11:4] | | X[11:4] |
| | | | | | |
+--------+--------+ +-----------------+ +-----------------+
Bytes 2 and 1 need to be shifted left by 4 bits, the least significant
nibble of each is stored in byte 3. Currently they are only
being shifted by 3 causing the reported coordinates to be incorrect.
This matches downstream examples, and has been confirmed on my
device (OnePlus 7 Pro).
Fixes: 0145a7141e ("Input: add support for the Samsung S6SY761 touchscreen")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20210305185710.225168-1-caleb@connolly.tech
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03e2c9c782 ]
req->sample[1] is not naturally aligned at word boundary, and therefore we
should use get_unaligned_be16() when accessing it.
Fixes: 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845 controller support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820830ec91 ]
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 676650d007 ]
When TOUCHSCREEN_ADC is enabled and IIO_BUFFER is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- TOUCHSCREEN_ADC [=y] && !UML && INPUT [=y] && INPUT_TOUCHSCREEN [=y] && IIO [=y]
The reason is that TOUCHSCREEN_ADC selects IIO_BUFFER_CB without depending
on or selecting IIO_BUFFER while IIO_BUFFER_CB depends on IIO_BUFFER. This
can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: aa132ffb6b ("input: touchscreen: resistive-adc-touch: add generic resistive ADC touchscreen")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201102221504.541279-1-fazilyildiran@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7842087b01 ]
MMS345L is another first generation touch screen from Melfas,
which uses mostly the same registers as MMS152.
However, there is some garbage printed during initialization.
Apparently MMS345L does not have the MMS152_COMPAT_GROUP register
that is read+printed during initialization.
TSP FW Rev: bootloader 0x6 / core 0x26 / config 0x26, Compat group: \x06
On earlier kernel versions the compat group was actually printed as
an ASCII control character, seems like it gets escaped now.
But we probably shouldn't print something from a random register.
Add a separate "melfas,mms345l" compatible that avoids reading
from the MMS152_COMPAT_GROUP register. This might also help in case
there is some other device-specific quirk in the future.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20200423102431.2715-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f8f770575 ]
MMS345L is another first generation touch screen from Melfas,
which uses the same registers as MMS152.
However, using I2C_M_NOSTART for it causes errors when reading:
i2c i2c-0: sendbytes: NAK bailout.
mms114 0-0048: __mms114_read_reg: i2c transfer failed (-5)
The driver works fine as soon as I2C_M_NOSTART is removed.
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200405170904.61512-1-stephan@gerhold.net
[dtor: removed separate mms345l handling, made everyone use standard
transfer mode, propagated the 10bit addressing flag to the read part of the
transfer as well.]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e112324cc0 ]
The EP0700MLP1 returns bogus data on the first register read access
(reading the threshold parameter from register 0x00):
edt_ft5x06 2-0038: crc error: 0xfc expected, got 0x40
It ignores writes until then. This patch adds a dummy read after which
the number of sensors and parameter read/writes work correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97e24b0953 upstream.
The driver misses a check for devm_thermal_zone_of_sensor_register().
Add a check to fix it.
Fixes: e28d0c9cd3 ("input: convert sun4i-ts to use devm_thermal_zone_of_sensor_register")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b32391ed6 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40 (aka MS Surface 2.0/Pixelsense)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-8-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 463fa44eec ]
Across suspend and resume, we are seeing error messages like the following:
atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)
This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.
Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79aae6acbe ]
The device md->input is used after it is released. Setting the device
data to NULL is unnecessary as the device is never used again. Instead,
md->input should be assigned NULL to avoid accessing the freed memory
accidently. Besides, checking md->si against NULL is superfluous as it
points to a variable address, which cannot be NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1572936379-6423-1-git-send-email-bianpan2016@163.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dde2744321 ]
A certain silead controller (Chip ID: 0x56810000) loses its firmware
after suspend, causing the resume to fail. This patch tries to load
the firmware, should a resume error occur and retries the resuming.
Signed-off-by: Julian Sax <jsbc@gmx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 937c4e552f upstream.
We need to turn regulators on and off when switching brightness, and
that may block, therefore we have to set stmfts_brightness_set() as
LED's brightness_set_blocking() method.
Fixes: 78bcac7b2a ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Acked-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e3c336ad8 upstream.
If the user attempts to update Atmel device with an invalid configuration
cfg file, error handling code is trying to free cfg file memory which is
not allocated yet hence results into kernel crash.
This patch fixes the order of memory free operations.
Signed-off-by: Sanjeev Chugh <sanjeev_chugh@mentor.com>
Fixes: a4891f1058 ("Input: atmel_mxt_ts - zero terminate config firmware file")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3f7c3fcf6 ]
Loading then unloading wm97xx-ts.ko when CONFIG_AC97_BUS=m
causes a WARNING: from drivers/base/driver.c:
Unexpected driver unregister!
WARNING: CPU: 0 PID: 1709 at ../drivers/base/driver.c:193 driver_unregister+0x30/0x40
Fix this by only calling driver_unregister() with the same
condition that driver_register() is called.
Fixes: ae9d1b5fbd ("Input: wm97xx: add new AC97 bus support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry writes:
"Input updates for v4.19-rc5
Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - allow for max == min during input_absinfo validation
Input: elantech - enable middle button of touchpad on ThinkPad P72
Input: atakbd - fix Atari CapsLock behaviour
Input: atakbd - fix Atari keymap
Input: egalax_ts - add system wakeup support
Input: gpio-keys - fix a documentation index issue
This patch adds wakeup function support for egalax touch
screen, if "wakeup-source" is added to device tree's egalax
touch screen node, the wakeup function will be enabled, and
egalax touch screen will be able to wakeup system from suspend.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If T9.CTRL DISAMP is set, then pressure is reported as zero. This means
some app layers (eg tslib) will ignore the contact.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We use sscanf to parse the configuration file, so it's necessary to zero
terminate the configuration otherwise a truncated file can cause the
parser to run off into uninitialised memory.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On devices with the T71 object, the config CRC will start there, rather
than at T7.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver only registers one input device, which uses the screen
parameters from the first T9 instance. The first T63 instance also uses
those parameters.
It is incorrect to send input reports from the second instances of these
objects if they are enabled: the input scaling will be wrong and the
positions will be mashed together.
This also causes problems on Android if the number of slots exceeds 32.
In the future, this could be handled by looking for enabled touch object
instances and creating an input device for each one.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wdt87xx_resume() is never called in atomic context. It calls mdelay() to
busily wait, which is not necessary. mdelay() can be replaced with
msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I do not think Vojtech wants snail mail these days (and he mentioned that
nobody has ever sent him snail mail), and the address is not even valid
anymore, so let's remove snail-mail instructions from the sources.
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
