For android builds we disable the check for curlun->prevent_medium_removal.
Instead we let the framework manage unmounting policy, as we sometimes need
to unmount after the media has been removed.
This also helps support hosts that do not inform the device when the media
has been unmounted.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Use this rather than calling usb_gadget_disconnect and usb_gadget_connect
directly to avoid sending USB disconnect events to userspace when resetting
the bus.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Add switch to notify current USB configuration. This can be used to detect
USB connect and disconnect events.
Broadcast a change via the usb_composite class when a USB function is
enabled or disabled.
Rename usb_function.hidden to usb_function.disabled.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Integrate support for android composite driver and platform data
within CONFIG_USB_ANDROID_MASS_STORAGE.
Signed-off-by: Mike Lockwood <lockwood@android.com>
As part of formating the mass storage device, Host sends the INQUIRY
scsi command. As per the standard, the command length for this
command should be 6 bytes, whereas the Vista host sends 12 bytes.
When the command length of the command is not equal to the standard
length, the device sends a phase error as part of the status phase.
When the host receives a phase error, it re-enumerates, hence the
error.
If the command is INQUIRY, and the command length is 12 bytes,
treating this as a good command and not sending the phase error
to the host fixes this issue.
Signed-off-by: Velempati Chiranjeevi <c_cvelem@qualcomm.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
Pulling in some code from file_storage.c, we now handle interface changes
in do_set_config(), which is now not called until any pending requests have
been successfully completed or cancelled.
This fixes a race condition that resulted in usb_ep_free_request() being called
while the request is still busy.
Signed-off-by: Mike Lockwood <lockwood@android.com>
The old code did not allways disable interrupts when called from thread
context, but tried to lock the same spinlock from interrupt context.
This was merged from a change to drivers/usb/function/mass_storage.c
in the android-msm-2.6.29 branch.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
This fixes a load ordering issue that occurred if a function driver loads before
the android gadget driver is initialized.
Signed-off-by: Mike Lockwood <lockwood@android.com>
This avoids excessive caching at the block level layer when copying large
files to the storage device.
Signed-off-by: Mike Lockwood <lockwood@android.com>
gether_disconnect() is always called before gether_connect() by the different
USB ethernet functions, so this warning was firing during normal operation.
Change-Id: I178cc7d1f67e9e87ac2e99c6674c4db8fcddf4a0
Signed-off-by: Mike Lockwood <lockwood@android.com>
Only set device descriptor bDeviceClass field to USB_CLASS_COMM when
the RNDIS function is actually enabled.
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: f_mass_storage: use dev_set_name()
Replacing strcpy() to device->bus_id which no longer exists in 2.6.32
Change-Id: Id978c881f457044c750bfd62f4c5bcc35bcd4fc5
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: f_adb: Claim endpoints so they are not reused by another function.
Change-Id: Ic9536cca800162e701c81cab36054f51ea759b72
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: f_acm: Fix crashes in acm_set_alt()
Change-Id: I91b761d392f8b1ca8784c69069b43e402b90d6a4
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: f_acm: Include android code only if CONFIG_USB_ANDROID_ACM is set.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: Android support for RNDIS serial ethernet function.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: android: Add function name to android_register_function printk.
Change-Id: I38bf79d9b544cdeaec9385f7482a131417fc4b23
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: android gadget: add remote wakeup attribute to android function
Add remote wakeup attribute to configuration descriptor of android
function to advertise remote wakeup capability to host
Acked-by: Allam, Suresh Reddy <sallam@qualcomm.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: android: Allow functions to handle setup requests.
Signed-off-by: Mike Lockwood <lockwood@android.com>
Support for specifying the list of USB functions from platform data.
The main android.c gadget driver no longer has hard coded references
to the mass_storage and adb functions.
Support for computing the product ID based on tables in platform data
and the currently enabled functions.
Moved the adb enable/disable logic from android.c to f_adb.c.
Change-Id: I6259d3fb1473ed973f700e55d17744956f3527bb
Signed-off-by: Mike Lockwood <lockwood@android.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: android gadget: add remote wakeup attribute to android function
Add remote wakeup attribute to configuration descriptor of android
function to advertise remote wakeup capability to host
Acked-by: Allam, Suresh Reddy <sallam@qualcomm.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb gadget: link fixes for android composite gadget
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb gadget: Fix null pointer errors in android composite driver
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: android: Allow usb charging to draw up to 500mA instead of 250.
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
usb gadget: android: Add helper function for usb_gadget_connect and disconnect.
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: call switch_dev_unregister in mass storage unbind callback
This fixes a problem unloading the android gadget driver when built as a module
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: android: Add dependency on switch driver.
Signed-off-by: Mike Lockwood <lockwood@android.com>
USB: gadget: android: Fix USB WHQL Certification Issues
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Add "usb_mass_storage" platform driver.
This will be used for configuring vendor, product and release from board file.
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Use usb_mass_storage platform device as parent for lun
If a platform device is specified for the f_mass_storage function, use it as the
parent driver for the lun files in sysfs.
This allows a platform independent file path for controlling USB mass storage
from user space.
Signed-off-by: Mike Lockwood <lockwood@android.com>
drivers: usb: gadget: Add platform data struct for usb_mass_storage device
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: mass_storage: Fix Mass Storage Panic during PC reboot
Submitted on behalf of RaviKumar Vembu <ravi.v@motorola.com>
Signed-off-by: Jared Suttles <jared.suttles@motorola.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: f_mass_storage: Handle setup request correctly
Signed-off-by: Mike Lockwood <lockwood@android.com>
usb: gadget: f_mass_storage: Clean up wakelocks on error paths
Signed-off-by: Rebecca Schultz Zavin <rebecca@android.com>
Signed-off-by: Mike Lockwood <lockwood@android.com>
This patch (as1429) updates the Kconfig help text for
CONFIG_USB_SUSPEND. The power/level file is now deprecated; we should
tell people to use power/control instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 46034dca51 (USB: musb_gadget_ep0: stop
abusing musb_gadget_set_halt()) forgot to restart a queued request after
clearing the endpoint halt feature. This results in a couple of USB resets
while enumerating the file-backed storage gadget due to CSW packet not being
sent for the MODE SENSE(10) command.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the issue which was observed while transfering
a large file ( > 20MB) over USB (OMAP MUSB controller acts as USB host)
to an attached USB thumb drive.
It was found that CDB field of CBW packet was set to 0x0. This was
due to missing a barrier before DMA engine starts transfer.
This buffer is allocated using dma_alloc_coherent which gives
non-cacheble but bufferable memory and hence needed a write
memory barrier to flush the write buffer.
More info on this thread is here:
http://www.spinics.net/lists/linux-omap/msg33987.html
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one bugs of OUT transfer in double buffer case:
-the current code only enable autoclear for dma mode 1, and not
for dma mode 0
Without this patch, test #5 of usbtest can't be passed if we
configure musb as g_zero and use fifo mode 3 to enable double
buffer mode.
With this patch and the following patch(fix dma length),
on my beagle B5, test#5(queued bulk out) may go beyond
18Mbyte/s(seems dma mode 0 is quicker in double buffer case)
if musb is configured as g_zero and fifo mode 3 is taken, follows
the test command:
#./testusb -D DEV_NAME -c 1024 -t 5 -s 32768 -g 8 [1]
Also I have tested this patch can't make g_ether broken.
[1],source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one infinite hang of bulk IN transfer in double buffer
case, the hang can be observed easily by test #6 of usbtest if musb is
configured as g_zero and fifo mode 3 is taken to enable double fifo.
In fact, the patch only removes the check for non-empty fifo before
loading data from new request into fifo since the check is not correct:
-in double buffer case, fifo may accommodate more than one packet,
even though it has contained one packet already and is non-empty
-since last DMA is completed before calling musb_g_tx, it is sure
that fifo may accommodate at least one packet
Without applying the patch, new requst enqueued from .complte may not
have a chance to be loaded into fifo, then will never be completed and
cause infinite hangs.
With the patch, on my beagle B5, test#6(queued bulk in) can be passed and
test result may go beyond 33Mbyte/s if musb is configured as g_zero and
fifo mode 3 is taken, follows the test command:
#testusb -D DEV_NAME -c 1024 -t 6 -s 32768 -g 8 [1]
[1],
-source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent changes in the usbhid layer exposed a bug in usbcore. If
CONFIG_USB_DYNAMIC_MINORS is enabled then an interface may be assigned
a minor number of 0. However interfaces that aren't registered as USB
class devices also have their minor number set to 0, during
initialization. As a result usb_find_interface() may return the
wrong interface, leading to a crash.
This patch (as1418) fixes the problem by initializing every
interface's minor number to -1. It also cleans up the
usb_register_dev() function, which besides being somewhat awkwardly
written, does not unwind completely on all its error paths.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Philip J. Turmel <philip@turmel.org>
Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Matthias Bayer <jackdachef@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TIOCGICOUNT device ioctl in both mos7720.c and mos7840.c allows
unprivileged users to read uninitialized stack memory, because the
"reserved" member of the serial_icounter_struct struct declared on the
stack is not altered or zeroed before being copied back to the user.
This patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 461c317705eca5cac09a360f488715927fd0a927(into 2.6.36-v3)
is put forward to power down phy if no usb cable is connected,
but does introduce the two issues below:
1), phy is not into work state if usb cable is connected
with PC during poweron, so musb device mode is not usable
in such case, follows the reasons:
-twl4030_phy_resume is not called, so
regulators are not enabled
i2c access are not enabled
usb mode not configurated
2), The kernel warings[1] of regulators 'unbalanced disables'
is caused if poweron without usb cable connected
with PC or b-device.
This patch fixes the two issues above:
-power down phy only if no usb cable is connected with PC
and b-device
-do phy initialization(via __twl4030_phy_resume) if usb cable
is connected with PC(vbus event) or another b-device(ID event) in
twl4030_usb_probe.
This patch also doesn't put VUSB3V1 LDO into active mode in
twl4030_usb_ldo_init until VBUS/ID change detected, so we can
save more power consumption than before.
This patch is verified OK on Beagle board either connected with
usb cable or not when poweron.
[1]. warnings of 'unbalanced disables' of regulators.
[root@OMAP3EVM /]# dmesg
------------[ cut here ]------------
WARNING: at drivers/regulator/core.c:1357 _regulator_disable+0x38/0x128()
unbalanced disables for VUSB1V8
Modules linked in:
Backtrace:
[<c0030c48>] (dump_backtrace+0x0/0x110) from [<c034f5a8>] (dump_stack+0x18/0x1c)
r7:c78179d8 r6:c01ed6b8 r5:c0410822 r4:0000054d
[<c034f590>] (dump_stack+0x0/0x1c) from [<c0057da8>] (warn_slowpath_common+0x54/0x6c)
[<c0057d54>] (warn_slowpath_common+0x0/0x6c) from [<c0057e64>] (warn_slowpath_fmt+0x38/0x40)
r9:00000000 r8:00000000 r7:c78e6608 r6:00000000 r5:fffffffb
r4:c78e6c00
[<c0057e2c>] (warn_slowpath_fmt+0x0/0x40) from [<c01ed6b8>] (_regulator_disable+0x38/0x128)
r3:c0410e53 r2:c0410ad5
[<c01ed680>] (_regulator_disable+0x0/0x128) from [<c01ed87c>] (regulator_disable+0x24/0x38)
r7:c78e6608 r6:00000000 r5:c78e6c40 r4:c78e6c00
[<c01ed858>] (regulator_disable+0x0/0x38) from [<c02382dc>] (twl4030_phy_power+0x15c/0x17c)
r5:c78595c0 r4:00000000
[<c0238180>] (twl4030_phy_power+0x0/0x17c) from [<c023831c>] (twl4030_phy_suspend+0x20/0x2c)
r6:00000000 r5:c78595c0 r4:c78595c0
[<c02382fc>] (twl4030_phy_suspend+0x0/0x2c) from [<c0238638>] (twl4030_usb_irq+0x11c/0x16c)
r5:c78595c0 r4:00000040
[<c023851c>] (twl4030_usb_irq+0x0/0x16c) from [<c034ec18>] (twl4030_usb_probe+0x2c4/0x32c)
r6:00000000 r5:00000000 r4:c78595c0
[<c034e954>] (twl4030_usb_probe+0x0/0x32c) from [<c02152a0>] (platform_drv_probe+0x20/0x24)
r7:00000000 r6:c047d49c r5:c78e6608 r4:c047d49c
[<c0215280>] (platform_drv_probe+0x0/0x24) from [<c0214244>] (driver_probe_device+0xd0/0x190)
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c02143d4>] (__device_attach+0x44/0x48)
r7:00000000 r6:c78e6608 r5:c78e6608 r4:c047d49c
[<c0214390>] (__device_attach+0x0/0x48) from [<c0213694>] (bus_for_each_drv+0x50/0x90)
r5:c0214390 r4:00000000
[<c0213644>] (bus_for_each_drv+0x0/0x90) from [<c0214474>] (device_attach+0x70/0x94)
r6:c78e663c r5:c78e6608 r4:c78e6608
[<c0214404>] (device_attach+0x0/0x94) from [<c02134fc>] (bus_probe_device+0x2c/0x48)
r7:00000000 r6:00000002 r5:c78e6608 r4:c78e6600
[<c02134d0>] (bus_probe_device+0x0/0x48) from [<c0211e48>] (device_add+0x340/0x4b4)
[<c0211b08>] (device_add+0x0/0x4b4) from [<c021597c>] (platform_device_add+0x110/0x16c)
[<c021586c>] (platform_device_add+0x0/0x16c) from [<c0220cb0>] (add_numbered_child+0xd8/0x118)
r7:00000000 r6:c045f15c r5:c78e6600 r4:00000000
[<c0220bd8>] (add_numbered_child+0x0/0x118) from [<c001c618>] (twl_probe+0x3a4/0x72c)
[<c001c274>] (twl_probe+0x0/0x72c) from [<c02601ac>] (i2c_device_probe+0x7c/0xa4)
[<c0260130>] (i2c_device_probe+0x0/0xa4) from [<c0214244>] (driver_probe_device+0xd0/0x190)
r5:c7856e20 r4:c047c860
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c02143d4>] (__device_attach+0x44/0x48)
r7:c7856e04 r6:c7856e20 r5:c7856e20 r4:c047c860
[<c0214390>] (__device_attach+0x0/0x48) from [<c0213694>] (bus_for_each_drv+0x50/0x90)
r5:c0214390 r4:00000000
[<c0213644>] (bus_for_each_drv+0x0/0x90) from [<c0214474>] (device_attach+0x70/0x94)
r6:c7856e54 r5:c7856e20 r4:c7856e20
[<c0214404>] (device_attach+0x0/0x94) from [<c02134fc>] (bus_probe_device+0x2c/0x48)
r7:c7856e04 r6:c78fd048 r5:c7856e20 r4:c7856e20
[<c02134d0>] (bus_probe_device+0x0/0x48) from [<c0211e48>] (device_add+0x340/0x4b4)
[<c0211b08>] (device_add+0x0/0x4b4) from [<c0211fd8>] (device_register+0x1c/0x20)
[<c0211fbc>] (device_register+0x0/0x20) from [<c0260aa8>] (i2c_new_device+0xec/0x150)
r5:c7856e00 r4:c7856e20
[<c02609bc>] (i2c_new_device+0x0/0x150) from [<c0260dc0>] (i2c_register_adapter+0xa0/0x1c4)
r7:00000000 r6:c78fd078 r5:c78fd048 r4:c781d5c0
[<c0260d20>] (i2c_register_adapter+0x0/0x1c4) from [<c0260f80>] (i2c_add_numbered_adapter+0x9c/0xb4)
r7:00000a28 r6:c04600a8 r5:c78fd048 r4:00000000
[<c0260ee4>] (i2c_add_numbered_adapter+0x0/0xb4) from [<c034efa4>] (omap_i2c_probe+0x324/0x3e8)
r5:00000000 r4:c78fd000
[<c034ec80>] (omap_i2c_probe+0x0/0x3e8) from [<c02152a0>] (platform_drv_probe+0x20/0x24)
[<c0215280>] (platform_drv_probe+0x0/0x24) from [<c0214244>] (driver_probe_device+0xd0/0x190)
[<c0214174>] (driver_probe_device+0x0/0x190) from [<c021436c>] (__driver_attach+0x68/0x8c)
r7:c78b2140 r6:c047e214 r5:c04600e4 r4:c04600b0
[<c0214304>] (__driver_attach+0x0/0x8c) from [<c021399c>] (bus_for_each_dev+0x50/0x84)
r7:c78b2140 r6:c047e214 r5:c0214304 r4:00000000
[<c021394c>] (bus_for_each_dev+0x0/0x84) from [<c0214068>] (driver_attach+0x20/0x28)
r6:c047e214 r5:c047e214 r4:c00270d0
[<c0214048>] (driver_attach+0x0/0x28) from [<c0213274>] (bus_add_driver+0xa8/0x228)
[<c02131cc>] (bus_add_driver+0x0/0x228) from [<c02146a4>] (driver_register+0xb0/0x13c)
[<c02145f4>] (driver_register+0x0/0x13c) from [<c0215744>] (platform_driver_register+0x4c/0x60)
r9:00000000 r8:c001f688 r7:00000013 r6:c005b6fc r5:c00083dc
r4:c00270d0
[<c02156f8>] (platform_driver_register+0x0/0x60) from [<c001f69c>] (omap_i2c_init_driver+0x14/0x1c)
[<c001f688>] (omap_i2c_init_driver+0x0/0x1c) from [<c002c460>] (do_one_initcall+0xd0/0x1a4)
[<c002c390>] (do_one_initcall+0x0/0x1a4) from [<c0008478>] (kernel_init+0x9c/0x154)
[<c00083dc>] (kernel_init+0x0/0x154) from [<c005b6fc>] (do_exit+0x0/0x688)
r5:c00083dc r4:00000000
---[ end trace 1b75b31a2719ed1d ]---
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
