[ Upstream commit 3c4ed72a16 ]
CSID hardware on SM8250 can demux up to 4 simultaneous streams
based on virtual channel (vc) or datatype (dt).
The CSID subdevice entity now has 4 source ports that can be
enabled/disabled and thus can control which virtual channels
are enabled. Datatype demuxing not tested.
In order to keep a valid internal state of the subdevice,
implicit format propagation from the sink to the source pads
has been preserved. However, the format on each source pad
can be different and in that case it must be configured explicitly.
CSID's s_stream is called when any stream is started or stopped.
It will call configure_streams() that will rewrite IRQ settings to HW.
When multiple streams are running simultaneously there is an issue
when writing IRQ settings for one stream while another is still
running, thus avoid re-writing settings if they were not changed
in link setup, or by fully powering off the CSID hardware.
Signed-off-by: Milen Mitkov <quic_mmitkov@quicinc.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stable-dep-of: e655d1ae9703 ("media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the ability to enable or disable multiple regulators in bulk with
camss. This is useful for sm8250, sdm845 and it looks like sdm660 where we
have more than one CSI regulator to do at once.
It should just work for standalone existing vdda regulators and parts which
don't have an explicitly defined CSI regulator.
[hverkuil: fix camss-csid.c:163:13: warning: 'ret' may be used uninitialized in this function]
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Titan 480 camss found on SM8250 has 6 CSIPHY and 4 VFE/CSID.
CSID is compatible with the Titan 170 CSID, but the Titan 480 CSID are
inside the VFE region (between the "top" and "bus" registers), so a
workaround is added to avoid ioremap failure.
[bod] Fixed setting camnoc_axi_clk_src instead of camcc_camnoc_axi_clk
[jgrahsl, bod] Add slow_ahb_src clock values
[jgrahsl, bod] Add cpa_ahb clock values
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Co-developed-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Julian Grahsl <jgrahsl@snap.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In order to support Qualcomm ISP hardware architectures that diverge
from older architectures, the CSID subdevice drivers needs to be refactored
to better abstract the different ISP hardware architectures.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CSI-2 spec defines format identifier for Data Type (DT),
and how the Decode Format (DF) & Encode Format (EF) are implemented.
The spec does however not define the DF, EF or Plain Format (PF)
identifiers, as those are vendor specific.
Plain formats describe the size of the pixels written by the RDI
units to memory. PLAIN8 for example has the size 8 bits, and
PLAIN32 32 bits. The appropriate Plain Format is determined by
the Decode Format used. The smallest Plain Format that is able
to contain a pixel of the used Decode Format is the appropriate
one to use.
As the vendor specific identifiers differ between hardware
generations, split them out into separate headers.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the 8x16 and 8x96 support different formats, separate the
arrays which contain the supported formats. For the VFE also
add separate arrays for RDI and PIX subdevices.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add structs with 8x96 resources. As the number of CSIPHY, CSID
and VFE hardware modules is different on 8x16 and 8x96 select
the number at runtime and allocate needed structures
dynamically.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support for camera subsystem on QComm MSM8996/APQ8096 is to be added
so remove hardware version from CAMSS driver's path.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
