[ Upstream commit 9039cd4c61635b2d541009a7cd5e2cc052402f28 ]
CSR.OPS bits specify the current operating mode and (according to
documentation) they are updated by HW when the operating mode change
request is processed. To comply with this check CSR.OPS before proceeding.
Commit introduces ravb_set_opmode() that does all the necessities for
setting the operating mode (set CCC.OPC (and CCC.GAC, CCC.CSEL, if any) and
wait for CSR.OPS) and call it where needed. This should comply with all the
HW manuals requirements as different manual variants specify that different
modes need to be checked in CSR.OPS when setting CCC.OPC.
If gPTP active in config mode is supported and it needs to be enabled, the
CCC.GAC and CCC.CSEL needs to be configured along with CCC.OPC in the same
write access. For this, ravb_set_opmode() allows passing GAC and CSEL as
part of opmode and the function updates accordingly CCC register.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf9bc396e05081ca281ffb0cd41e44db478ff26 ]
On RZ/G3S SMARC Carrier II board having RGMII connections b/w Ethernet
MACs and PHYs it has been discovered that doing unbind/bind for ravb
driver in a loop leads to wrong speed and duplex for Ethernet links and
broken connectivity (the connectivity cannot be restored even with
bringing interface down/up). Before doing unbind/bind the Ethernet
interfaces were configured though systemd. The sh instructions used to
do unbind/bind were:
$ cd /sys/bus/platform/drivers/ravb/
$ while :; do echo 11c30000.ethernet > unbind ; \
echo 11c30000.ethernet > bind; done
It has been discovered that there is a race b/w IOCTLs initialized by
systemd at the response of success binding and the
"ravb_write(ndev, CCC_OPC_RESET, CCC)" call in ravb_remove() as
follows:
1/ as a result of bind success the user space open/configures the
interfaces tough an IOCTL; the following stack trace has been
identified on RZ/G3S:
Call trace:
dump_backtrace+0x9c/0x100
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
dump_stack+0x18/0x28
ravb_open+0x70/0xa58
__dev_open+0xf4/0x1e8
__dev_change_flags+0x198/0x218
dev_change_flags+0x2c/0x80
devinet_ioctl+0x640/0x708
inet_ioctl+0x1e4/0x200
sock_do_ioctl+0x50/0x108
sock_ioctl+0x240/0x358
__arm64_sys_ioctl+0xb0/0x100
invoke_syscall+0x50/0x128
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0xb8
el0t_64_sync_handler+0xc0/0xc8
el0t_64_sync+0x190/0x198
2/ this call may execute concurrently with ravb_remove() as the
unbind/bind operation was executed in a loop
3/ if the operation mode is changed to RESET (through
ravb_write(ndev, CCC_OPC_RESET, CCC) call in ravb_remove())
while the above ravb_open() is in progress it may lead to MAC
(or PHY, or MAC-PHY connection, the right point hasn't been identified
at the moment) to be broken, thus the Ethernet connectivity fails to
restore.
The simple fix for this is to move ravb_write(ndev, CCC_OPC_RESET, CCC))
after unregister_netdev() to avoid resetting the controller while the
netdev interface is still registered.
To avoid future issues in ravb_remove(), the patch follows the proper order
of operations in ravb_remove(): reverse order compared with ravb_probe().
This avoids described races as the IOCTLs as well as unregister_netdev()
(called now at the beginning of ravb_remove()) calls rtnl_lock() before
continuing and IOCTLs check (though devinet_ioctl()) if device is still
registered just after taking the lock:
int devinet_ioctl(struct net *net, unsigned int cmd, struct ifreq *ifr)
{
// ...
rtnl_lock();
ret = -ENODEV;
dev = __dev_get_by_name(net, ifr->ifr_name);
if (!dev)
goto done;
// ...
done:
rtnl_unlock();
out:
return ret;
}
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eac16a733427ba0de2449ffc7bd3da32ddb65cb7 ]
In case ravb_phy_start() returns with error the settings applied in
ravb_dmac_init() are not reverted (e.g. config mode). For this call
ravb_stop_dma() on failure path of ravb_open().
Fixes: a0d2f20650 ("Renesas Ethernet AVB PTP clock driver")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d78c0ced60d5e2f8b5a4a0468a5c400b24aeadf2 ]
Hardware manual of RZ/G3S (and RZ/G2L) specifies the following on the
description of CXR35 register (chapter "PHY interface select register
(CXR35)"): "After release reset, make write-access to this register before
making write-access to other registers (except MDIOMOD). Even if not need
to change the value of this register, make write-access to this register
at least one time. Because RGMII/MII MODE is recognized by accessing this
register".
The setup procedure for EMAC module (chapter "Setup procedure" of RZ/G3S,
RZ/G2L manuals) specifies the E-MAC.CXR35 register is the first EMAC
register that is to be configured.
Note [A] from chapter "PHY interface select register (CXR35)" specifies
the following:
[A] The case which CXR35 SEL_XMII is used for the selection of RGMII/MII
in APB Clock 100 MHz.
(1) To use RGMII interface, Set ‘H’03E8_0000’ to this register.
(2) To use MII interface, Set ‘H’03E8_0002’ to this register.
Take into account these indication.
Fixes: 1089877ada ("ravb: Add RZ/G2L MII interface support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88b74831faaee455c2af380382d979fc38e79270 ]
pm_runtime_get_sync() may return an error. In case it returns with an error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8eb6ea4b302e7ff78535c205510e359ac10a0bd ]
reset_control_deassert() could return an error. Some devices cannot work
if reset signal de-assert operation fails. To avoid this check the return
code of reset_control_deassert() in ravb_probe() and take proper action.
Along with it, the free_netdev() call from the error path was moved after
reset_control_assert() on its own label (out_free_netdev) to free
netdev in case reset_control_deassert() fails.
Fixes: 0d13a1a464 ("ravb: Add reset support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9870257a0a338cd8d6c1cddab74e703f490f6779 ]
Fix races between ravb_tx_timeout_work() and functions of net_device_ops
and ethtool_ops by using rtnl_trylock() and rtnl_unlock(). Note that
since ravb_close() is under the rtnl lock and calls cancel_work_sync(),
ravb_tx_timeout_work() should calls rtnl_trylock(). Otherwise, a deadlock
may happen in ravb_tx_timeout_work() like below:
CPU0 CPU1
ravb_tx_timeout()
schedule_work()
...
__dev_close_many()
// Under rtnl lock
ravb_close()
cancel_work_sync()
// Waiting
ravb_tx_timeout_work()
rtnl_lock()
// This is possible to cause a deadlock
If rtnl_trylock() fails, rescheduling the work with sleep for 1 msec.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231127122420.3706751-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f5ebf5dae ]
RAVB doesn't need mdiobus suspend/resume, that's why it sets
'mac_managed_pm'. However, setting it needs to be moved from init to
probe, so mdiobus PM functions will really never be called (e.g. when
the interface is not up yet during suspend/resume).
Fixes: 4924c0cdce ("net: ravb: Fix PHY state warning splat during system resume")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3c07758c9 ]
Since this driver enables the interrupt by RIC2_QFE1, this driver
should clear the interrupt flag if it happens. Otherwise, the interrupt
causes to hang the system.
Note that this also fix a minor coding style (a comment indentation)
around the fixed code.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2b6cdee1d ]
After system entered Suspend to RAM, registers setting of this
hardware is reset because the SoC will be turned off. On R-Car Gen3
(info->ccc_gac), ravb_ptp_init() is called in ravb_probe() only. So,
after system resumed, it lacks of the initial settings for ptp. So,
add ravb_ptp_{init,stop}() into ravb_{resume,suspend}().
Fixes: f5d7837f96 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c72a7e4259 upstream.
This patch fixes the error "ravb 11c20000.ethernet eth0: failed to switch
device to config mode" during unbind.
We are doing register access after pm_runtime_put_sync().
We usually do cleanup in reverse order of init. Currently in
remove(), the "pm_runtime_put_sync" is not in reverse order.
Probe
reset_control_deassert(rstc);
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
remove
pm_runtime_put_sync(&pdev->dev);
unregister_netdev(ndev);
..
ravb_mdio_release(priv);
pm_runtime_disable(&pdev->dev);
Consider the call to unregister_netdev()
unregister_netdev->unregister_netdevice_queue->rollback_registered_many
that calls the below functions which access the registers after
pm_runtime_put_sync()
1) ravb_get_stats
2) ravb_close
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221214105118.2495313-1-biju.das.jz@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 1197 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xc8
As the Renesas Ethernet AVB driver already calls phy_{stop,start}() in
its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8ec796f47620980fdd0403e21bd8b7200b4fa1d4.1663598796.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RZ/V2M Ethernet is very similar to R-Car Gen3 Ethernet-AVB, though
some small parts are the same as R-Car Gen2.
Other differences to R-Car Gen3 and Gen2 are:
* It has separate data (DI), error (Line 1) and management (Line 2) irqs
rather than one irq for all three.
* Instead of using the High-speed peripheral bus clock for gPTP, it has a
separate gPTP reference clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/V2M has a separate gPTP reference clock that is used when the
AVB-DMAC Mode Register (CCC) gPTP Clock Select (CSEL) bits are
set to "01: High-speed peripheral bus clock".
Therefore, add a feature that allows this clock to be used for
gPTP.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car has a combined interrupt line, ch22 = Line0_DiA | Line1_A | Line2_A.
RZ/V2M has separate interrupt lines for each of these, so add a feature
that allows the driver to get these interrupts and call the common handler.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when the HW has a single interrupt, the driver uses the
GIC, TIC, RIC0 registers to enable and disable interrupts.
When the HW has multiple interrupts, it uses the GIE, GID, TIE, TID,
RIE0, RID0 registers.
However, other devices, e.g. RZ/V2M, have multiple irqs and only have
the GIC, TIC, RIC0 registers.
Therefore, split this into a separate feature.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
'max_rx_len' can be up to GBETH_RX_BUFF_MAX (i.e. 8192) (see
'gbeth_hw_info').
The default value of 'num_rx_ring' can be BE_RX_RING_SIZE (i.e. 1024).
So this loop can allocate 8 Mo of memory.
Previous memory allocations in this function already use GFP_KERNEL, so
use __netdev_alloc_skb() and an explicit GFP_KERNEL instead of a
implicit GFP_ATOMIC.
This gives more opportunities of successful allocation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ravb_close() always returns 0, hence the check in ravb_wol_restore() is
pointless (however, we cannot change the prototype of ravb_close() as it
implements the driver's ndo_stop() method).
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
After following the call tree of phy_set_max_speed(), it became clear
that this function never returns anything but 0, so we can change its
result type to *void* and drop the result checks from the three drivers
that actually bothered to do it...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the typo AVB->DMAC in comment, as the code following the comment
is for DMAC on Gigabit Ethernet IP.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch enables Receive/Transmit port of TOE and removes
the setting of promiscuous bit from EMAC configuration mode register.
This patch also update EMAC configuration mode comment from
"PAUSE prohibition" to "EMAC Mode: PAUSE prohibition; Duplex; TX;
RX; CRC Pass Through".
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename the feature bit "nc_queue" with "nc_queues" as AVB DMAC has
RX and TX NC queues.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rename the variable "tsrq" with "tccr_mask" as we are passing
TCCR mask to the ravb_wait() function.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RZ/G2L E-MAC supports carrier counters.
Add a carrier_counter hw feature bit to struct ravb_hw_info
to add this feature only for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_rx_gbeth() function to support RZ/G2L.
This patch also renames ravb_rcar_rx to ravb_rx_rcar to be
consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_rx_ring_format_gbeth() function to support RZ/G2L.
This patch also renames ravb_rx_ring_format to ravb_rx_ring_format_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_rx_ring_free_gbeth() function to support RZ/G2L.
This patch also renames ravb_rx_ring_free to ravb_rx_ring_free_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fillup ravb_alloc_rx_desc_gbeth() function to support RZ/G2L.
This patch also renames ravb_alloc_rx_desc to ravb_alloc_rx_desc_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
R-Car AVB-DMAC has maximum 2K size on RX buffer, whereas on RZ/G2L
it is 8K. We need to allow for changing the MTU within the limit
of the maximum size of a descriptor.
Add a rx_max_buf_size variable to struct ravb_hw_info to handle
this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize GbEthernet E-MAC found on RZ/G2L SoC.
This patch also renames ravb_set_rate to ravb_set_rate_rcar and
ravb_rcar_emac_init to ravb_emac_init_rcar to be consistent with
the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/G2L supports half duplex mode.
Add a half_duplex hw feature bit to struct ravb_hw_info for
supporting half duplex mode for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-MAC on R-Car supports magic packet detection, whereas RZ/G2L
does not support this feature. Add magic_pkt to struct ravb_hw_info
and enable this feature only for R-Car.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car AVB-DMAC has 4 Transmit start request queues, whereas
RZ/G2L has only 1 Transmit start request queue.
Add a tsrq variable to struct ravb_hw_info to handle this
difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
