This patch drops the i2c timing tables from this driver and instead
derives the timing based from the requested clock sleep. The timing
tables were completely wrong anyway when observed on a scope.
This new algorithm is also only derived by using a scope, but it seems
to produce much more accurate result.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
[wsa: changed messages from dev_err to dev_warn]
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Enable AESS data in hwmod in order to be able to probe
audio driver.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add AESS memory bank data in hwmod in order to provide memory address
information to the driver.
This version also changes the AESS main clock to use a
non-CLKCTRL-based functional clock. These are being removed from the
clock data, since they should be handled by the IP block integration
code. Without this change, the kernel crashes during boot. Thanks to
Tony Lindgren for reporting this during a test merge.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
[paul@pwsan.com: updated to change the AESS main_clk]
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Enable the AESS auto-gating control bit during AESS hwmod setup. This
fixes the following boot warning on OMAP4:
omap_hwmod: aess: _wait_target_disable failed
Without this patch, the AESS IP block does not indicate to the PRCM
that it is idle after it is reset. This prevents some types of SoC
power management until something sets the auto-gating control bit.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Add a basic header file for the TI AESS IP block, located in the OMAP4
Audio Back-End subsystem.
Currently, this header file only contains a function to enable the
AESS internal clock auto-gating. This will be used by a subsequent
patch to ensure that the AESS won't block the entire chip
low-power-idle mode. We wish to be able to place the AESS into idle
even when no AESS driver has been compiled in.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After setup/enable, some IP blocks need some additional setting to
indicate the PRCM that they are inactive until they are configured.
Some examples on OMAP4 include the AESS and FSUSB IP blocks.
To fix this cleanly, this patch adds another optional function
pointer, enable_preprogram, to the IP block's hwmod data. The function
that is pointed to is called by the hwmod code immediately after the
IP block is reset.
This version of the patch includes a patch description fix from Felipe.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
The kernel might be invoked through the reset vector, so to
preserve parameters passed to it, temp regs that are not
in the function parameter range needs to be used.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
This the basic functional Invensense MPU6050 Device driver.
Signed-off-by: Ge Gao <ggao@invensense.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add dtsi for imx6q and imx6dl with non-common blocks moved into there.
Major differences between imx6dl and imx6q:
* Dual vs. Quad cores
* single vs. dual IPU
* 128 vs. 256 KB OCRAM
* imx6q: ECSPI5, OpenVG (GC355), SATA
* imx6dl: I2C4, PXP, EPDC, LCDIF
* iomuxc/pads definition
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
i.MX6 Quad and i.MX6 DualLite is similar enough to share one dtsi
file, so rename imx6q.dtsi to imx6qdl.dtsi preparing for the addition
of imx6dl support.
Another member of i.MX6 series i.MX6 SoloLite is different enough
from the other two, so it will stand as a separate dtsi. That's why
we rename to imx6qdl.dtsi not imx6.dtsi.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For ANATOP LDOs, vddcpu, vddsoc and vddpu
have step time settings in the misc2 register, need
to add necessary step time info for these three LDOs,
then regulator driver can add necessary delay based on
these settings.
offset 0x170:
bit [24-25]: vddcpu
bit [26-27]: vddpu
bit [28-29]: vddsoc
field definition:
0'b00: 64 cycles of 24M clock;
0'b01: 128 cycles of 24M clock;
0'b02: 256 cycles of 24M clock;
0'b03: 512 cycles of 24M clock;
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Update operating-points per hardware document and add support for
1 GHz and 1.2 GHz frequencies.
400 MHz, 800 MHz and 1 GHz should be supported by all i.MX6Q chips,
while 1.2 GHz support needs to know from OTP fuse bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This mxs usbphy is only needs to be on after system boots
up, and software never needs to control it anymore.
Meanwhile, usbphy's parent needs to be notified if usb
is suspend or not. So we design below mxs usbphy usage:
- usbphy1_gate and usbphy2_gate:
Their parents are dummy clock, we only needs to enable
it after system boots up.
- usbphy1 and usbphy2
Usage reserved bit for this clock, in that case, the refcount
will be updated, but without hardware changing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove silicon version from SDMA firmware.
This makes it consistent with other i.MX SoCs firmware names.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The MBa53 is a baseboard for the TQMA53 embedded module. This enables/adds only
supported devices, i.e. it is not feature complete, because of missing drivers
in mainline linux.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The tqma53 is an embedded module that has some features on board (e.g. emmc),
but mostly just provides access to them on its interface.
Going along with the imx53.dtsi, the tqma53.dtsi specifies the existing
devices and their pinctrl for this module. All devices that are not on the
module are disabled by default and need to be enabled in a baseboard DT.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The keypad is on the accessory board of i.MX51 babbage
main board and is driven by Keypad Port(KPP) in SoC.
The keymap is the same to i.MX25 3stack platform as
the accessory board schematic tells that it is designed
in this way.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Just to keep consistency with other dts files, place 'status' entry as the last
one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Following omap3-evm.dts way, it changes all imx dts files to use label
in board dts to refer to nodes defined by soc dtsi. Thus, the board
dts files become easier to read and edit with the least indentation
levels.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add missing imx dtb targets, so that make dtbs can cover all imx dtbs.
It's pretty useful for testing dts changes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add an entry for imx27-pdk.dtb, so that it can be generated by default.
Also, add an entry into Documentation/devicetree/bindings/arm/fsl.txt.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Any devices wishing to use the AB8500's GPIO IRQs were forced to
request virtual IRQs from the gpio-ab8500 driver. Now that
responsibility has been passed back to the AB8500 core driver,
devices can request real IRQ numbers instead. This patch removes
any traces of the old virtual IRQ conversion handlers, which will
force any drivers requesting IRQs to use real IRQS.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AB8500 GPIO no longer handles its GPIO IRQs. Instead, the AB8500
core driver has taken back the responsibility. Prior to this
happening, the AB8500 GPIO driver provided a set of virtual IRQs
which were used as a pass-through. These virtual IRQs had a base
of MOP500_AB8500_VIR_GPIO_IRQ_BASE, which was passed though pdata.
We don't need to do this anymore, so we're pulling out the
property from the structure.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make it harder to do mistakes by introducing the actual
defined ABx500 IRQ number into the IRQ cluster definitions.
Deduct cluster offset from the GPIO offset to make each
cluster coherent.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ABx500 GPIO controller used to provide a set of virtual contiguous
IRQs for use by sub-devices, but they have been removed after a request
from Mainline Maintainers. Now the AB8500 core driver deals with almost
all IRQ related issues instead.
The ABx500 GPIO driver is now only used to convert between GPIO and IRQ
numbers which is actually quite difficult, as the ABx500 GPIO's
associated IRQs are clustered together throughout the interrupt number
space at irregular intervals. To solve this quandary, we have placed the
read-in values into the existing cluster information table to use during
conversion.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Moved irq_base removal into this patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In its current state the gpio-ab8500 driver looks after some GPIO
lines found on the AB8500 MFD chip. It also controls all of its
own IRQ handling for these GPIOs by inventing some virtual IRQs
and handing those out to sub-devices. There has been quite a bit
of controversy over this and it was a contributing factor to the
driver being marked as BROKEN in Mainline.
The reason for adopting this method was due to added complexity
in the hardware. Unusually, each GPIO has two separate IRQs
associated with it, one for a rising and a different one for a
falling interrupt. Using this method complicates matters further
because the GPIO IRQs are actually sandwiched between a bunch
of IRQs which are handled solely by the AB8500 core driver.
The best way for us to take this forward is to get rid of the
virtual IRQs and only hand out the rising IRQ lines. If a
sub-driver wishes to request a falling interrupt, they can do
so by requesting a rising line in the normal way. They just
have to add IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_BOTH, if
they require both in the flags. Then if a falling IRQ is
triggered, the AB8500 core driver will know how to handle the
added complexity accordingly. This should greatly simply things.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Augment to keep irq_base for a while (removed later)]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes a few obvious bugs in DSP loader stuff:
- Fix possible memory leaks in the error path
- Avoid double-free calls in dma_reset()
- Properly set/unset WC bits for DMA buffers
- Add missing error status checks
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Base the DSP firmware transfer and communication timeouts on jiffy values.
Signed-off-by: Ian Minett <ian_minett@creativelabs.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove 32-bit x86 a cmdline param "no-hlt",
and the cpuinfo_x86.hlt_works_ok that it sets.
If a user wants to avoid HLT, then "idle=poll"
is much more useful, as it avoids invocation of HLT
in idle, while "no-hlt" failed to do so.
Indeed, hlt_works_ok was consulted in only 3 places.
First, in /proc/cpuinfo where "hlt_bug yes"
would be printed if and only if the user booted
the system with "no-hlt" -- as there was no other code
to set that flag.
Second, check_hlt() would not invoke halt() if "no-hlt"
were on the cmdline.
Third, it was consulted in stop_this_cpu(), which is invoked
by native_machine_halt()/reboot_interrupt()/smp_stop_nmi_callback() --
all cases where the machine is being shutdown/reset.
The flag was not consulted in the more frequently invoked
play_dead()/hlt_play_dead() used in processor offline and suspend.
Since Linux-3.0 there has been a run-time notice upon "no-hlt" invocations
indicating that it would be removed in 2012.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
mwait_idle() is a C1-only idle loop intended to be more efficient
than HLT, starting on Pentium-4 HT-enabled processors.
But mwait_idle() has been replaced by the more general
mwait_idle_with_hints(), which handles both C1 and deeper C-states.
ACPI processor_idle and intel_idle use only mwait_idle_with_hints(),
and no longer use mwait_idle().
Here we simplify the x86 native idle code by removing mwait_idle(),
and the "idle=mwait" bootparam used to invoke it.
Since Linux 3.0 there has been a boot-time warning when "idle=mwait"
was invoked saying it would be removed in 2012. This removal
was also noted in the (now removed:-) feature-removal-schedule.txt.
After this change, kernels configured with
(CONFIG_ACPI=n && CONFIG_INTEL_IDLE=n) when run on hardware
that supports MWAIT will simply use HLT. If MWAIT is desired
on those systems, cpuidle and the cpuidle drivers above
can be enabled.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
This macro is only invoked by Xen,
so make its definition specific to Xen.
> set_pm_idle_to_default()
< xen_set_default_idle()
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: xen-devel@lists.xensource.com
From Rob Herring:
highbank fixes for 3.8
-Compile fix for !SMP
-More cpu cluster id related fixes
* tag 'highbank-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux:
ARM: highbank: mask cluster id from cpu_logical_map
ARM: scu: mask cluster id from cpu_logical_map
ARM: scu: add empty scu_enable for !CONFIG_SMP
Looks like there are few more places that I missed that can cause
compiler warnings. After grepping for omap initcall, all files
needing soc.h should now have it.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
I needed this when compiling for pandaboard.
The reason this is needed is that we are now using
omap_initcalls to keep them multiplatform safe.
Signed-off-by: André Hentschel <nerv@dawncrow.de>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
