WCH382 2S board is a PCIe card with 2 DB9 COM ports detected as
Serial controller: Device 1c00:3253 (rev 10) (prog-if 05 [16850])
Signed-off-by: Jeremy McNicoll <jmcnicol@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wait_for_xmitr() function is only used if CONFIG_CONSOLE_POLL
or CONFIG_SERIAL_OMAP_CONSOLE are set, but when both are disabled,
the compiler warns about it being unused:
drivers/tty/serial/omap-serial.c:1168:13: warning: 'wait_for_xmitr' defined but not used [-Wunused-func
We could add more #ifdefs to work around it, but adding __maybe_unused
seems nicer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 2172076d23 ("serial/omap-serial: Deinline wait_for_xmitr, save 165 bytes")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The omap-serial driver emulates RS485 delays using software timers,
but neglects to clamp the input values from the unprivileged
ioctl(TIOCSRS485). Because the software implementation busy-waits,
malicious userspace could stall the cpu for ~49 days.
Clamp the input values to < 100ms.
Fixes: 4a0ac0f55b ("OMAP: add RS485 support")
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recently added uniphier 8250 port driver supports early console
probing, and it supports being built as a module, but the combination
of the two fails to link:
ERROR: "early_serial8250_setup" [drivers/tty/serial/8250/8250_uniphier.ko] undefined!
Given that earlycon support in a loadable module makes no sense,
making that code conditional on 'MODULE' is a correct solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b8d20e06ea ("serial: 8250_uniphier: add earlycon support")
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB fixes from Greg KH:
"Here are some USB fixes for 4.5-rc3.
The usual, xhci fixes for reported issues, combined with some small
gadget driver fixes, and a MAINTAINERS file update. All have been in
linux-next with no reported issues"
* tag 'usb-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: harden xhci_find_next_ext_cap against device removal
xhci: Fix list corruption in urb dequeue at host removal
usb: host: xhci-plat: fix NULL pointer in probe for device tree case
usb: xhci-mtk: fix AHB bus hang up caused by roothubs polling
usb: xhci-mtk: fix bpkts value of LS/HS periodic eps not behind TT
usb: xhci: apply XHCI_PME_STUCK_QUIRK to Intel Broxton-M platforms
usb: xhci: set SSIC port unused only if xhci_suspend succeeds
usb: xhci: add a quirk bit for ssic port unused
usb: xhci: handle both SSIC ports in PME stuck quirk
usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.
Revert "xhci: don't finish a TD if we get a short-transfer event mid TD"
MAINTAINERS: fix my email address
usb: dwc2: Fix probe problem on bcm2835
Revert "usb: dwc2: Move reset into dwc2_get_hwparams()"
usb: musb: ux500: Fix NULL pointer dereference at system PM
usb: phy: mxs: declare variable with initialized value
usb: phy: msm: fix error handling in probe.
Pull staging and IIO driver fixes from Greg KH:
"Here are some IIO and staging driver fixes for 4.5-rc3.
All of them, except one, are for IIO drivers, and one is for a speakup
driver fix caused by some earlier patches, to resolve a reported build
failure"
* tag 'staging-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: speakup: Fix allyesconfig build on mn10300
iio: dht11: Use boottime
iio: ade7753: avoid uninitialized data
iio: pressure: mpl115: fix temperature offset sign
iio: imu: Fix dependencies for !HAS_IOMEM archs
staging: iio: Fix dependencies for !HAS_IOMEM archs
iio: adc: Fix dependencies for !HAS_IOMEM archs
iio: inkern: fix a NULL dereference on error
iio:adc:ti_am335x_adc Fix buffered mode by identifying as software buffer.
iio: light: acpi-als: Report data as processed
iio: dac: mcp4725: set iio name property in sysfs
iio: add HAS_IOMEM dependency to VF610_ADC
iio: add IIO_TRIGGER dependency to STK8BA50
iio: proximity: lidar: correct return value
iio-light: Use a signed return type for ltr501_match_samp_freq()
This patch address a possible security issue:
The request field in client notify request ioctl comes from user space
as u32 and is downcasted to u8 with out validation.
Check request field to have approved values
MEI_HBM_NOTIFICATION_STAR/STOP
Cc: <stable@vger.kernel.org> #4.3+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iAMT WD client has to be whitelisted sice it has two connections
and is filtered out by number_of_connections fixup.
Also the API has changed for BDW and SKL but firmware haven't updated
the protocol version.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add entry for displaying current watchdog internal state
cat <debugfs>/mei_wdt/state
IDLE|START|RUNNING|STOPPING
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of integrating the iAMT watchdog in the mei core driver
we will create a watchdog device on the mei client bus and
create a driver for it.
This patch removes the watchdog code from the mei core driver.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We left few function prototypes in the header file after
moving nfc logic to bus.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copy completed callback content to the user space
if we have such callback ready in the beginning of the read.
Simplify offset processing logic as byproduct.
This is a refinement for:
commit 139aacf757 ("mei: fix read after read scenario")
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MEI FW can receive only one flow control for read.
Currently the driver only checks if a flow control credit was already
sent and read is pending in the rd_pending queue, but it also has to
check if flow control credit already queued in the write control queue
to prevent sending more than one flow control credits.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove uuid from the debug messages in bus-fixup.c
as this is already part of the device name.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
allmodconfig build of alpha, m68k, m32r, tilepro has failed with the
error:
drivers/staging/wilc1000/wilc_wfi_cfgoperations.c: In function 'wilc_create_wiphy':
drivers/staging/wilc1000/wilc_wfi_cfgoperations.c:2632:13:
error: 'struct wiphy' has no member named 'wowlan'
Looking at other drivers wowlan can be only used when CONFIG_PM is
defined.
Fixes: 73584a40d7 ("staging: wilc1000: add ops resuem/suspend/wakeup in cfg80211")
Cc: Glen Lee <glen.lee@atmel.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ethtool_ops has attributes in sub struct ethtool_coalesce that
correspond to the parameters intagg_delay and dynamic_intagg. It is
preferable to set these properties with ethtool rather than
module_param, so create these attributes in adapter and set them using
ethtool_coalesce's rx_coalesce_usecs and rx_use_adaptive_coalesce.
(Outlined in TODO file)
Signed-off-by: Kevin Wern <kevin.m.wern@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function value inside se_cmd can change if the TMR is cancelled.
Use original ATIO Type to correctly determine CTIO response.
Signed-off-by: Swapnil Nagle <swapnil.nagle@purestroage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ Upstream Commit 84e32a06f4 ]
Commit 84e32a0 ("qla2xxx: Use pci_enable_msix_range() instead of
pci_enable_msix()") introduced a regression when target mode is enabled.
In qla24xx_enable_msix(), ha->max_rsp_queues was incorrectly set
to a value higher than the number of response queues allocated causing
an invalid dereference. Specifically here in qla2x00_init_rings():
*rsp->in_ptr = 0;
Add additional check to make sure the pointer is valid. following
call stack will be seen
---- 8< ----
RIP: 0010:[<ffffffffa02ccadc>] [<ffffffffa02ccadc>] qla2x00_init_rings+0xdc/0x320 [qla2xxx]
RSP: 0018:ffff880429447dd8 EFLAGS: 00010082
....
Call Trace:
[<ffffffffa02ceb40>] qla2x00_abort_isp+0x170/0x6b0 [qla2xxx]
[<ffffffffa02c6f77>] qla2x00_do_dpc+0x357/0x7f0 [qla2xxx]
[<ffffffffa02c6c20>] ? qla2x00_relogin+0x260/0x260 [qla2xxx]
[<ffffffff8107d2c9>] kthread+0xc9/0xe0
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
[<ffffffff8172cc6f>] ret_from_fork+0x3f/0x70
[<ffffffff8107d200>] ? flush_kthread_worker+0x90/0x90
---- 8< ----
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When the tty lock is interrupted on attempted re-open, 2 tty krefs
are still held. Drop extra kref before returning failure from
tty_lock_interruptible(), and drop lookup kref before returning
failure from tty_open().
Fixes: 0bfd464d3f ("tty: Wait interruptibly for tty lock on reopen")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uio_mem structure has a member that is a phys_addr_t, but can
be a number of other types too. The target core driver attempts
to assign a pointer from vmalloc() to it, by casting it to
phys_addr_t, but that causes a warning when phys_addr_t is longer
than a pointer:
drivers/target/target_core_user.c: In function 'tcmu_configure_device':
drivers/target/target_core_user.c:906:22: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
This adds another cast to uintptr_t to shut up the warning.
A nicer fix might be to have additional fields in uio_mem
for the different purposes, so we can assign a pointer directly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a race between setting of SCF_SEND_DELAYED_TAS
in transport_send_task_abort(), and check of the same bit in
transport_check_aborted_status().
It adds a __transport_check_aborted_status() version that is
used by target_execute_cmd() when se_cmd->t_state_lock is
held, and a transport_check_aborted_status() wrapper for
all other existing callers.
Also, it handles the case where the check happens before
transport_send_task_abort() gets called. For this, go
ahead and set SCF_SEND_DELAYED_TAS early when necessary,
and have transport_send_task_abort() send the abort.
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add driver for the TI AFE4403 heart rate monitor and pulse oximeter.
This device detects reflected LED light fluctuations and presents an ADC
value to the user space for further signal processing.
Data sheet located here:
http://www.ti.com/product/AFE4403/datasheet
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add the TI AFE4403 heart monitor DT bindings documentation.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add driver for the TI AFE4404 heart rate monitor and pulse oximeter.
This device detects reflected LED light fluctuations and presents an ADC
value to the user space for further signal processing.
Datasheet: http://www.ti.com/product/AFE4404/datasheet
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add the TI afe4404 heart monitor DT bindings documentation.
Create health directory created under iio.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch replaces the clk_get() with devm_clk_get().Accordingly,modified
the error paths,rename error labels and removed clk_put() in probe() &
remove functions.
Signed-off-by: Hari Prasath Gujulan Elango <hgujulan@visteon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The newly added atlas-ph-sensor driver uses irq_work_queue, which
may not always be enabled:
ERROR: "irq_work_queue" [drivers/iio/chemical/atlas-ph-sensor.ko] undefined!
This adds a 'select' statement to Kconfig to ensure it's there
when we need it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 27dec00ecf ("iio: chemical: add Atlas pH-SM sensor support")
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have the same code for computing the scan index storage size in bytes
all over the place. Factor this out into helper functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This will be used together with an external trigger (e.g hrtimer
based software trigger).
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This allows data exported via buffer interface to be converted
to standard units in userspace.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In this file,function names are otherwise used as pointers without &.
Found using coccinelle.
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
By slightly reordering the channels in the channel spec array we can reuse
the same array for all variant of the chip.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The hardware reset is currently done after phy_start() is called,
leading to a race where we can lose the link status if the phy state
machine calls dwceqos_adjust_link() before we reset the MAC registers.
Acked-by: Lars Persson <larper@axis.com>
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rcu stall with the following backtrace was seen on a system with
forwarding, optimistic_dad and use_optimistic set. To reproduce,
set these flags and allow ipv6 autoconf.
This occurs because the device write_lock is acquired while already
holding the read_lock. Back trace below -
INFO: rcu_preempt self-detected stall on CPU { 1} (t=2100 jiffies
g=3992 c=3991 q=4471)
<6> Task dump for CPU 1:
<2> kworker/1:0 R running task 12168 15 2 0x00000002
<2> Workqueue: ipv6_addrconf addrconf_dad_work
<6> Call trace:
<2> [<ffffffc000084da8>] el1_irq+0x68/0xdc
<2> [<ffffffc000cc4e0c>] _raw_write_lock_bh+0x20/0x30
<2> [<ffffffc000bc5dd8>] __ipv6_dev_ac_inc+0x64/0x1b4
<2> [<ffffffc000bcbd2c>] addrconf_join_anycast+0x9c/0xc4
<2> [<ffffffc000bcf9f0>] __ipv6_ifa_notify+0x160/0x29c
<2> [<ffffffc000bcfb7c>] ipv6_ifa_notify+0x50/0x70
<2> [<ffffffc000bd035c>] addrconf_dad_work+0x314/0x334
<2> [<ffffffc0000b64c8>] process_one_work+0x244/0x3fc
<2> [<ffffffc0000b7324>] worker_thread+0x2f8/0x418
<2> [<ffffffc0000bb40c>] kthread+0xe0/0xec
v2: do addrconf_dad_kick inside read lock and then acquire write
lock for ipv6_ifa_notify as suggested by Eric
Fixes: 7fd2561e4e ("net: ipv6: Add a sysctl to make optimistic
addresses useful candidates")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Erik Kline <ek@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare()/clk_unprepare() must not be called within atomic context.
This patch calls clk_prepare() once for all from atmel_sha_probe() and
clk_unprepare() from atmel_sha_remove().
Then calls of clk_prepare_enable()/clk_disable_unprepare() were replaced
by calls of clk_enable()/clk_disable().
Cc: stable@vger.kernel.org
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reported-by: Matthias Mayr <matthias.mayr@student.kit.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The async path cannot use MAY_BACKLOG because it is not meant to
block, which is what MAY_BACKLOG does. On the other hand, both
the sync and async paths can make use of MAY_SLEEP.
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Any access to non-constant bits of the private context must be
done under the socket lock, in particular, this includes ctx->req.
This patch moves such accesses under the lock, and fetches the
tfm from the parent socket which is guaranteed to be constant,
rather than from ctx->req.
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The async path in algif_skcipher assumes that the crypto completion
function will be called with the original request. This is not
necessarily the case. In fact there is no need for this anyway
since we already embed information into the request with struct
skcipher_async_req.
This patch adds a pointer to that struct and then passes it as
the data to the callback function.
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Tadeusz Struk <tadeusz.struk@intel.com>
Merge fixes from Andrew Morton:
"22 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
m32r: fix build failure due to SMP and MMU
...
Pull Ceph fixes from Sage Weil:
"We have a few wire protocol compatibility fixes, ports of a few recent
CRUSH mapping changes, and a couple error path fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: MOSDOpReply v7 encoding
libceph: advertise support for TUNABLES5
crush: decode and initialize chooseleaf_stable
crush: add chooseleaf_stable tunable
crush: ensure take bucket value is valid
crush: ensure bucket id is valid before indexing buckets array
ceph: fix snap context leak in error path
ceph: checking for IS_ERR instead of NULL
Pull drm fixes from Dave Airlie:
"Fixes all over the place:
- amdkfd: two static checker fixes
- mst: a bunch of static checker and spec/hw interaction fixes
- amdgpu: fix Iceland hw properly, and some fiji bugs, along with
some write-combining fixes.
- exynos: some regression fixes
- adv7511: fix some EDID reading issues"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (38 commits)
drm/dp/mst: deallocate payload on port destruction
drm/dp/mst: Reverse order of MST enable and clearing VC payload table.
drm/dp/mst: move GUID storage from mgr, port to only mst branch
drm/dp/mst: change MST detection scheme
drm/dp/mst: Calculate MST PBN with 31.32 fixed point
drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil
drm/mst: Add range check for max_payloads during init
drm/mst: Don't ignore the MST PBN self-test result
drm: fix missing reference counting decrease
drm/amdgpu: disable uvd and vce clockgating on Fiji
drm/amdgpu: remove exp hardware support from iceland
drm/amdgpu: load MEC ucode manually on iceland
drm/amdgpu: don't load MEC2 on topaz
drm/amdgpu: drop topaz support from gmc8 module
drm/amdgpu: pull topaz gmc bits into gmc_v7
drm/amdgpu: The VI specific EXE bit should only apply to GMC v8.0 above
drm/amdgpu: iceland use CI based MC IP
drm/amdgpu: move gmc7 support out of CIK dependency
drm/amdgpu/gfx7: enable cp inst/reg error interrupts
drm/amdgpu/gfx8: enable cp inst/reg error interrupts
...
Pull power management and ACPI fixes from Rafael Wysocki:
"These are: a fix for a recently introduced false-positive warnings
about PM domain pointers being changed inappropriately (harmless but
annoying), an MCH size workaround quirk for one more platform, a
compiler warning fix (generic power domains framework), an ACPI LPSS
(Intel SoCs) driver fixup and a cleanup of the ACPI CPPC core code.
Specifics:
- PM core fix to avoid false-positive warnings generated when the
pm_domain field is cleared for a device that appears to be bound to
a driver (Rafael Wysocki).
- New MCH size workaround quirk for Intel Haswell-ULT (Josh Boyer).
- Fix for an "unused function" compiler warning in the generic power
domains framework (Ulf Hansson).
- Fixup for the ACPI driver for Intel SoCs (acpi-lpss) to set the PM
domain pointer of a device properly in one place that was
overlooked by a recent PM core update (Andy Shevchenko).
- Removal of a redundant function declaration in the ACPI CPPC core
code (Timur Tabi)"
* tag 'pm+acpi-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Avoid false-positive warnings in dev_pm_domain_set()
PM / Domains: Silence compiler warning for an unused function
ACPI / CPPC: remove redundant mbox_send_message() declaration
ACPI / LPSS: set PM domain via helper setter
PNP: Add Haswell-ULT to Intel MCH size workaround
In the current implementation of the EPOLLEXCLUSIVE flag (added for
4.5-rc1), if epoll waiters create different POLL* sets and register them
as exclusive against the same target fd, the current implementation will
stop waking any further waiters once it finds the first idle waiter.
This means that waiters could miss wakeups in certain cases.
For example, when we wake up a pipe for reading we do:
wake_up_interruptible_sync_poll(&pipe->wait, POLLIN | POLLRDNORM); So if
one epoll set or epfd is added to pipe p with POLLIN and a second set
epfd2 is added to pipe p with POLLRDNORM, only epfd may receive the
wakeup since the current implementation will stop after it finds any
intersection of events with a waiter that is blocked in epoll_wait().
We could potentially address this by requiring all epoll waiters that
are added to p be required to pass the same set of POLL* events. IE the
first EPOLL_CTL_ADD that passes EPOLLEXCLUSIVE establishes the set POLL*
flags to be used by any other epfds that are added as EPOLLEXCLUSIVE.
However, I think it might be somewhat confusing interface as we would
have to reference count the number of users for that set, and so
userspace would have to keep track of that count, or we would need a
more involved interface. It also adds some shared state that we'd have
store somewhere. I don't think anybody will want to bloat
__wait_queue_head for this.
I think what we could do instead, is to simply restrict EPOLLEXCLUSIVE
such that it can only be specified with EPOLLIN and/or EPOLLOUT. So
that way if the wakeup includes 'POLLIN' and not 'POLLOUT', we can stop
once we hit the first idle waiter that specifies the EPOLLIN bit, since
any remaining waiters that only have 'POLLOUT' set wouldn't need to be
woken. Likewise, we can do the same thing if 'POLLOUT' is in the wakeup
bit set and not 'POLLIN'. If both 'POLLOUT' and 'POLLIN' are set in the
wake bit set (there is at least one example of this I saw in fs/pipe.c),
then we just wake the entire exclusive list. Having both 'POLLOUT' and
'POLLIN' both set should not be on any performance critical path, so I
think that's ok (in fs/pipe.c its in pipe_release()). We also continue
to include EPOLLERR and EPOLLHUP by default in any exclusive set. Thus,
the user can specify EPOLLERR and/or EPOLLHUP but is not required to do
so.
Since epoll waiters may be interested in other events as well besides
EPOLLIN, EPOLLOUT, EPOLLERR and EPOLLHUP, these can still be added by
doing a 'dup' call on the target fd and adding that as one normally
would with EPOLL_CTL_ADD. Since I think that the POLLIN and POLLOUT
events are what we are interest in balancing, I think that the 'dup'
thing could perhaps be added to only one of the waiter threads.
However, I think that EPOLLIN, EPOLLOUT, EPOLLERR and EPOLLHUP should be
sufficient for the majority of use-cases.
Since EPOLLEXCLUSIVE is intended to be used with a target fd shared
among multiple epfds, where between 1 and n of the epfds may receive an
event, it does not satisfy the semantics of EPOLLONESHOT where only 1
epfd would get an event. Thus, it is not allowed to be specified in
conjunction with EPOLLEXCLUSIVE.
EPOLL_CTL_MOD is also not allowed if the fd was previously added as
EPOLLEXCLUSIVE. It seems with the limited number of flags to not be as
interesting, but this could be relaxed at some further point.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Tested-by: Madars Vitolins <m@silodev.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Eric Wong <normalperson@yhbt.net>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Helper radix_tree_iter_retry() resets next_index to the current index.
In following radix_tree_next_slot current chunk size becomes zero. This
isn't checked and it tries to dereference null pointer in slot.
Tagged iterator is fine because retry happens only at slot 0 where tag
bitmask in iter->tags is filled with single bit.
Fixes: 46437f9a55 ("radix-tree: fix race in gang lookup")
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Jeremiah Mahler <jmmahler@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ea8f8fc863 ("MAINTAINERS: add linux-api for review of API/ABI
changes") added file triggers for various paths that likely indicated
API/ABI changes. However, catching all changes in Documentation/ABI/
and include/uapi/ produces a large volume of mail to linux-api, rather
than only API/ABI changes. Drop those two entries, but leave
include/linux/syscalls.h and kernel/sys_ni.c to catch syscall-related
changes.
[josh@joshtriplett.org: redid changelog]
Signed-off-by: Michael Kerrisk <mtk.man-pages@gmail.com>
Acked-by: Shuah khan <shuahkh@osg.samsung.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
