Pull networking fixes from Paolo Abeni:
"Including fixes from can and ipsec subtrees.
Current release - regressions:
- sched: fix off by one in htb_activate_prios()
- eth: mana: fix accessing freed irq affinity_hint
- eth: ice: fix out-of-bounds KASAN warning in virtchnl
Current release - new code bugs:
- eth: mtk_eth_soc: enable special tag when any MAC uses DSA
Previous releases - always broken:
- core: fix sk->sk_txrehash default
- neigh: make sure used and confirmed times are valid
- mptcp: be careful on subflow status propagation on errors
- xfrm: prevent potential spectre v1 gadget in xfrm_xlate32_attr()
- phylink: move phy_device_free() to correctly release phy device
- eth: mlx5:
- fix crash unsetting rx-vlan-filter in switchdev mode
- fix hang on firmware reset
- serialize module cleanup with reload and remove"
* tag 'net-6.2-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits)
selftests: forwarding: lib: quote the sysctl values
net: mscc: ocelot: fix all IPv6 getting trapped to CPU when PTP timestamping is used
rds: rds_rm_zerocopy_callback() use list_first_entry()
net: txgbe: Update support email address
selftests: Fix failing VXLAN VNI filtering test
selftests: mptcp: stop tests earlier
selftests: mptcp: allow more slack for slow test-case
mptcp: be careful on subflow status propagation on errors
mptcp: fix locking for in-kernel listener creation
mptcp: fix locking for setsockopt corner-case
mptcp: do not wait for bare sockets' timeout
net: ethernet: mtk_eth_soc: fix DSA TX tag hwaccel for switch port 0
nfp: ethtool: fix the bug of setting unsupported port speed
txhash: fix sk->sk_txrehash default
net: ethernet: mtk_eth_soc: fix wrong parameters order in __xdp_rxq_info_reg()
net: ethernet: mtk_eth_soc: enable special tag when any MAC uses DSA
net: sched: sch: Fix off by one in htb_activate_prios()
igc: Add ndo_tx_timeout support
net: mana: Fix accessing freed irq affinity_hint
hv_netvsc: Allocate memory in netvsc_dma_map() with GFP_ATOMIC
...
Marc Kleine-Budde says:
====================
can-next 2023-02-08
The 1st patch is by Oliver Hartkopp and cleans up the CAN_RAW's
raw_setsockopt() for CAN_RAW_FD_FRAMES.
The 2nd patch is by me and fixes the compilation if
CONFIG_CAN_CALC_BITTIMING is disabled. (Problem introduced in last
pull request to next-next.)
* tag 'linux-can-next-for-6.3-20230208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: bittiming: can_calc_bittiming(): add missing parameter to no-op function
can: raw: use temp variable instead of rolling back config
====================
Link: https://lore.kernel.org/r/20230208210014.3169347-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Saeed Mahameed says:
====================
mlx5-next-netdev-deadlock
This series from Jiri solves a deadlock when removing a network namespace
with mlx5 devlink instance being in it.
The deadlock is between:
1) mlx5_ib->unregister_netdevice_notifier()
AND
2) mlx5_core->devlink_reload->cleanup_net()
To slove this introduced mlx5 netdev added/removed events to track uplink
netdev to be used for register_netdevice_notifier_dev_net() purposes.
* tag 'mlx5-next-netdev-deadlock' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
RDMA/mlx5: Track netdev to avoid deadlock during netdev notifier unregister
net/mlx5e: Propagate an internal event in case uplink netdev changes
net/mlx5e: Fix trap event handling
net/mlx5: Introduce CQE error syndrome
====================
Link: https://lore.kernel.org/r/20230208005626.72930-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever uplink netdev is set/cleared, propagate newly introduced event
to inform notifier blocks netdev was added/removed.
Move the set() helper to core.c from header, introduce clear() and
netdev_added_event_replay() helpers. The last one is going to be called
from rdma driver, so export it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In commit 286c0e09e8 ("can: bittiming: can_changelink() pass extack
down callstack") a new parameter was added to can_calc_bittiming(),
however the static inline no-op (which is used if
CONFIG_CAN_CALC_BITTIMING is disabled) wasn't converted.
Add the new parameter to the static inline no-op of
can_calc_bittiming().
Fixes: 286c0e09e8 ("can: bittiming: can_changelink() pass extack down callstack")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/20230207201734.2905618-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Current taprio software implementation is haunted by the shadow of the
igb/igc hardware model. It iterates over child qdiscs in increasing
order of TXQ index, therefore giving higher xmit priority to TXQ 0 and
lower to TXQ N. According to discussions with Vinicius, that is the
default (perhaps even unchangeable) prioritization scheme used for the
NICs that taprio was first written for (igb, igc), and we have a case of
two bugs canceling out, resulting in a functional setup on igb/igc, but
a less sane one on other NICs.
To the best of my understanding, taprio should prioritize based on the
traffic class, so it should really dequeue starting with the highest
traffic class and going down from there. We get to the TXQ using the
tc_to_txq[] netdev property.
TXQs within the same TC have the same (strict) priority, so we should
pick from them as fairly as we can. We can achieve that by implementing
something very similar to q->curband from multiq_dequeue().
Since igb/igc really do have TXQ 0 of higher hardware priority than
TXQ 1 etc, we need to preserve the behavior for them as well. We really
have no choice, because in txtime-assist mode, taprio is essentially a
software scheduler towards offloaded child tc-etf qdiscs, so the TXQ
selection really does matter (not all igb TXQs support ETF/SO_TXTIME,
says Kurt Kanzenbach).
To preserve the behavior, we need a capability bit so that taprio can
determine if it's running on igb/igc, or on something else. Because igb
doesn't offload taprio at all, we can't piggyback on the
qdisc_offload_query_caps() call from taprio_enable_offload(), but
instead we need a separate call which is also made for software
scheduling.
Introduce two static keys to minimize the performance penalty on systems
which only have igb/igc NICs, and on systems which only have other NICs.
For mixed systems, taprio will have to dynamically check whether to
dequeue using one prioritization algorithm or using the other.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN8841 is completely integrated triple-speed (10BASE-T/ 100BASE-TX/
1000BASE-T) Ethernet physical layer transceivers for transmission and
reception of data on standard CAT-5, as well as CAT-5e and CAT-6,
unshielded twisted pair (UTP) cables.
The LAN8841 offers the industry-standard GMII/MII as well as the RGMII.
Some of the features of the PHY are:
- Wake on LAN
- Auto-MDIX
- IEEE 1588-2008 (V2)
- LinkMD Capable diagnosis
Currently the patch offers support only for link configuration.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, each core device has VF pages counter which stores number of
fw pages used by its VFs and SFs.
The current design led to a hang when performing firmware reset on DPU,
where the DPU PFs stalled in sriov unload flow due to waiting on release
of SFs pages instead of waiting on only VFs pages.
Thus, Add a separate counter for SF firmware pages, which will prevent
the stall scenario described above.
Fixes: 1958fc2f07 ("net/mlx5: SF, Add auxiliary device driver")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, an independent page counter is used for tracking memory usage
for each function type such as VF, PF and host PF (DPU).
For better code-readibilty, use a single array that stores
the number of allocated memory pages for each function type.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The recently introduced sched_numa_hop_mask() exposes cpumasks of CPUs
reachable within a given distance budget, wrap the logic for iterating over
all (distance, mask) values inside an iterator macro.
Signed-off-by: Valentin Schneider <vschneid@redhat.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq has pointed out that drivers allocating IRQ vectors would benefit
from having smarter NUMA-awareness - cpumask_local_spread() only knows
about the local node and everything outside is in the same bucket.
sched_domains_numa_masks is pretty much what we want to hand out (a cpumask
of CPUs reachable within a given distance budget), introduce
sched_numa_hop_mask() to export those cpumasks.
Link: http://lore.kernel.org/r/20220728191203.4055-1-tariqt@nvidia.com
Signed-off-by: Valentin Schneider <vschneid@redhat.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function finds Nth set CPU in a given cpumask starting from a given
node.
Leveraging the fact that each hop in sched_domains_numa_masks includes the
same or greater number of CPUs than the previous one, we can use binary
search on hops instead of linear walk, which makes the overall complexity
of O(log n) in terms of number of cpumask_weight() calls.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Peter Lafreniere <peter@n8pjl.ca>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce cpumask_nth_and_andnot() based on find_nth_and_andnot_bit().
It's used in the following patch to traverse cpumasks without storing
intermediate result in temporary cpumask.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Peter Lafreniere <peter@n8pjl.ca>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the following patches the function is used to implement in-place bitmaps
traversing without storing intermediate result in temporary bitmaps.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Peter Lafreniere <peter@n8pjl.ca>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case a new string DB is added to the FW, the FW publishes an event
notifying the strings DB have updated.
Add support in driver for handling this event.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Commit 90e7cb78b8 ("net/mlx5: fix missing mutex_unlock in
mlx5_fw_fatal_reporter_err_work()") introduced another checking of
MLX5_DROP_HEALTH_NEW_WORK. At this point, the first check of
MLX5_DROP_HEALTH_NEW_WORK is redundant and so is the lock that
protects it.
Remove the lock and rename MLX5_DROP_HEALTH_NEW_WORK to reflect these
changes.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
We have many places using this expression:
SKB_DATA_ALIGN(sizeof(struct skb_shared_info))
Use of SKB_HEAD_ALIGN() will allow to clean them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-02-06
this is a pull request of 47 patches for net-next/master.
The first two patch is by Oliver Hartkopp. One adds missing error
checking to the CAN_GW protocol, the other adds a missing CAN address
family check to the CAN ISO TP protocol.
Thomas Kopp contributes a performance optimization to the mcp251xfd
driver.
The next 11 patches are by Geert Uytterhoeven and add support for
R-Car V4H systems to the rcar_canfd driver.
Stephane Grosjean and Lukas Magel contribute 8 patches to the peak_usb
driver, which add support for configurable CAN channel ID.
The last 17 patches are by me and target the CAN bit timing
configuration. The bit timing is cleaned up, error messages are
improved and forwarded to user space via NL_SET_ERR_MSG_FMT() instead
of netdev_err(), and the SJW handling is updated, including the
definition of a new default value that will benefit CAN-FD
controllers, by increasing their oscillator tolerance.
* tag 'linux-can-next-for-6.3-20230206' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (47 commits)
can: bittiming: can_validate_bitrate(): report error via netlink
can: bittiming: can_calc_bittiming(): convert from netdev_err() to NL_SET_ERR_MSG_FMT()
can: bittiming: can_calc_bittiming(): clean up SJW handling
can: bittiming: can_sjw_set_default(): use Phase Seg2 / 2 as default for SJW
can: bittiming: can_sjw_check(): check that SJW is not longer than either Phase Buffer Segment
can: bittiming: can_sjw_check(): report error via netlink and harmonize error value
can: bittiming: can_fixup_bittiming(): report error via netlink and harmonize error value
can: bittiming: factor out can_sjw_set_default() and can_sjw_check()
can: bittiming: can_changelink() pass extack down callstack
can: netlink: can_changelink(): convert from netdev_err() to NL_SET_ERR_MSG_FMT()
can: netlink: can_validate(): validate sample point for CAN and CAN-FD
can: dev: register_candev(): bail out if both fixed bit rates and bit timing constants are provided
can: dev: register_candev(): ensure that bittiming const are valid
can: bittiming: can_get_bittiming(): use direct return and remove unneeded else
can: bittiming: can_fixup_bittiming(): set effective tq
can: bittiming: can_fixup_bittiming(): use CAN_SYNC_SEG instead of 1
can: bittiming(): replace open coded variants of can_bit_time()
can: peak_usb: Reorder include directives alphabetically
can: peak_usb: align CAN channel ID format in log with sysfs attribute
can: peak_usb: export PCAN CAN channel ID as sysfs device attribute
...
====================
Link: https://lore.kernel.org/r/20230206131620.2758724-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Factor out the functionality of assigning a SJW default value into
can_sjw_set_default() and the checking the SJW limits into
can_sjw_check().
This functions will be improved and called from a different function
in the following patches.
Link: https://lore.kernel.org/all/20230202110854.2318594-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch.
In order to pass warning/error messages during netlink calls back to
user space, pass the extack struct down the callstack of
can_changelink(), the actual error messages will be added in the
following ptaches.
Link: https://lore.kernel.org/all/20230202110854.2318594-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add sock_init_data_uid() to explicitly initialize the socket uid.
To initialise the socket uid, sock_init_data() assumes a the struct
socket* sock is always embedded in a struct socket_alloc, used to
access the corresponding inode uid. This may not be true.
Examples are sockets created in tun_chr_open() and tap_open().
Fixes: 86741ec254 ("net: core: Add a UID field to struct sock.")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 classes of in-tree drivers currently:
- those who act upon struct tc_taprio_sched_entry :: gate_mask as if it
holds a bit mask of TXQs
- those who act upon the gate_mask as if it holds a bit mask of TCs
When it comes to the standard, IEEE 802.1Q-2018 does say this in the
second paragraph of section 8.6.8.4 Enhancements for scheduled traffic:
| A gate control list associated with each Port contains an ordered list
| of gate operations. Each gate operation changes the transmission gate
| state for the gate associated with each of the Port's traffic class
| queues and allows associated control operations to be scheduled.
In typically obtuse language, it refers to a "traffic class queue"
rather than a "traffic class" or a "queue". But careful reading of
802.1Q clarifies that "traffic class" and "queue" are in fact
synonymous (see 8.6.6 Queuing frames):
| A queue in this context is not necessarily a single FIFO data structure.
| A queue is a record of all frames of a given traffic class awaiting
| transmission on a given Bridge Port. The structure of this record is not
| specified.
i.o.w. their definition of "queue" isn't the Linux TX queue.
The gate_mask really is input into taprio via its UAPI as a mask of
traffic classes, but taprio_sched_to_offload() converts it into a TXQ
mask.
The breakdown of drivers which handle TC_SETUP_QDISC_TAPRIO is:
- hellcreek, felix, sja1105: these are DSA switches, it's not even very
clear what TXQs correspond to, other than purely software constructs.
Only the mqprio configuration with 8 TCs and 1 TXQ per TC makes sense.
So it's fine to convert these to a gate mask per TC.
- enetc: I have the hardware and can confirm that the gate mask is per
TC, and affects all TXQs (BD rings) configured for that priority.
- igc: in igc_save_qbv_schedule(), the gate_mask is clearly interpreted
to be per-TXQ.
- tsnep: Gerhard Engleder clarifies that even though this hardware
supports at most 1 TXQ per TC, the TXQ indices may be different from
the TC values themselves, and it is the TXQ indices that matter to
this hardware. So keep it per-TXQ as well.
- stmmac: I have a GMAC datasheet, and in the EST section it does
specify that the gate events are per TXQ rather than per TC.
- lan966x: again, this is a switch, and while not a DSA one, the way in
which it implements lan966x_mqprio_add() - by only allowing num_tc ==
NUM_PRIO_QUEUES (8) - makes it clear to me that TXQs are a purely
software construct here as well. They seem to map 1:1 with TCs.
- am65_cpsw: from looking at am65_cpsw_est_set_sched_cmds(), I get the
impression that the fetch_allow variable is treated like a prio_mask.
This definitely sounds closer to a per-TC gate mask rather than a
per-TXQ one, and TI documentation does seem to recomment an identity
mapping between TCs and TXQs. However, Roger Quadros would like to do
some testing before making changes, so I'm leaving this driver to
operate as it did before, for now. Link with more details at the end.
Based on this breakdown, we have 5 drivers with a gate mask per TC and
4 with a gate mask per TXQ. So let's make the gate mask per TXQ the
opt-in and the gate mask per TC the default.
Benefit from the TC_QUERY_CAPS feature that Jakub suggested we add, and
query the device driver before calling the proper ndo_setup_tc(), and
figure out if it expects one or the other format.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20230202003621.2679603-15-vladimir.oltean@nxp.com/#25193204
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Siddharth Vadapalli <s-vadapalli@ti.com>
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The taprio qdisc does not currently pass the mqprio queue configuration
down to the offloading device driver. So the driver cannot act upon the
TXQ counts/offsets per TC, or upon the prio->tc map. It was probably
assumed that the driver only wants to offload num_tc (see
TC_MQPRIO_HW_OFFLOAD_TCS), which it can get from netdev_get_num_tc(),
but there's clearly more to the mqprio configuration than that.
I've considered 2 mechanisms to remedy that. First is to pass a struct
tc_mqprio_qopt_offload as part of the tc_taprio_qopt_offload. The second
is to make taprio actually call TC_SETUP_QDISC_MQPRIO, *in addition to*
TC_SETUP_QDISC_TAPRIO.
The difference is that in the first case, existing drivers (offloading
or not) all ignore taprio's mqprio portion currently, whereas in the
second case, we could control whether to call TC_SETUP_QDISC_MQPRIO,
based on a new capability. The question is which approach would be
better.
I'm afraid that calling TC_SETUP_QDISC_MQPRIO unconditionally (not based
on a taprio capability bit) would risk introducing regressions. For
example, taprio doesn't populate (or validate) qopt->hw, as well as
mqprio.flags, mqprio.shaper, mqprio.min_rate, mqprio.max_rate.
In comparison, adding a capability is functionally equivalent to just
passing the mqprio in a way that drivers can ignore it, except it's
slightly more complicated to use it (need to set the capability).
Ultimately, what made me go for the "mqprio in taprio" variant was that
it's easier for offloading drivers to interpret the mqprio qopt slightly
differently when it comes from taprio vs when it comes from mqprio,
should that ever become necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mqprio_parse_opt() proudly has a comment:
/* If hardware offload is requested we will leave it to the device
* to either populate the queue counts itself or to validate the
* provided queue counts.
*/
Unfortunately some device drivers did not get this memo, and don't
validate the queue counts, or populate them.
In case drivers don't want to populate the queue counts themselves, just
act upon the requested configuration, it makes sense to introduce a tc
capability, and make mqprio query it, so they don't have to do the
validation themselves.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First user of skb_poison_list is in kfree_skb_list_reason, to catch bugs
earlier like introduced in commit eedade12f4 ("net: kfree_skb_list use
kmem_cache_free_bulk"). For completeness mentioned bug have been fixed in
commit f72ff8b81e ("net: fix kfree_skb_list use of skb_mark_not_on_list").
In case of a bug like mentioned commit we would have seen OOPS with:
general protection fault, probably for non-canonical address 0xdead000000000870
And content of one the registers e.g. R13: dead000000000800
In this case skb->len is at offset 112 bytes (0x70) why fault happens at
0x800+0x70 = 0x870
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use BH context only for synchronization, so we don't care if it's
actually serving softirq or not.
As a side node, in case of threaded NAPI, in_serving_softirq() will
return false because it's in process context with BH off, making
page_pool_recycle_in_cache() unreachable.
Signed-off-by: Qingfang DENG <qingfang.deng@siflower.com.cn>
Tested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2023-02-04
This series provides misc updates to mlx5 driver:
1) Trivial LAG code cleanup patches from Roi
2) Rahul improves mlx5's documentation structure
Separates the documentation into multiple pages related to different
components in the device driver. Adds Kconfig parameters, devlink
parameters, and tracepoints that were previously introduced but not added
to the documentation. Introduces a new page on ethtool statistics counters
with information about counters previously implemented in the mlx5_core
driver but not documented in the kernel tree.
3) From Raed, policy/state selector support for IPSec.
4) From Fragos, add support for XDR speed in IPoIB mlx5 netdev
5) Few more misc cleanups and trivial changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 58e0be1ef6 ("net: use struct_group to copy ip/ipv6
header addresses"), ip and ipv6 headers started to use the __struct_group
definition, which is defined at include/uapi/linux/stddef.h. However,
linux/stddef.h isn't explicitly included in include/uapi/linux/{ip,ipv6}.h,
which breaks build of xskxceiver bpf selftest if you install the uapi
headers in the system:
$ make V=1 xskxceiver -C tools/testing/selftests/bpf
...
make: Entering directory '(...)/tools/testing/selftests/bpf'
gcc -g -O0 -rdynamic -Wall -Werror (...)
In file included from xskxceiver.c:79:
/usr/include/linux/ip.h:103:9: error: expected specifier-qualifier-list before ‘__struct_group’
103 | __struct_group(/* no tag */, addrs, /* no attrs */,
| ^~~~~~~~~~~~~~
...
Include the missing <linux/stddef.h> dependency in ip.h and do the
same for the ipv6.h header.
Fixes: 58e0be1ef6 ("net: use struct_group to copy ip/ipv6 header addresses")
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch added accounting for number of MDB entries per port and
per port-VLAN, and the logic to verify that these values stay within
configured bounds. However it didn't provide means to actually configure
those bounds or read the occupancy. This patch does that.
Two new netlink attributes are added for the MDB occupancy:
IFLA_BRPORT_MCAST_N_GROUPS for the per-port occupancy and
BRIDGE_VLANDB_ENTRY_MCAST_N_GROUPS for the per-port-VLAN occupancy.
And another two for the maximum number of MDB entries:
IFLA_BRPORT_MCAST_MAX_GROUPS for the per-port maximum, and
BRIDGE_VLANDB_ENTRY_MCAST_MAX_GROUPS for the per-port-VLAN one.
Note that the two new IFLA_BRPORT_ attributes prompt bumping of
RTNL_SLAVE_MAX_TYPE to size the slave attribute tables large enough.
The new attributes are used like this:
# ip link add name br up type bridge vlan_filtering 1 mcast_snooping 1 \
mcast_vlan_snooping 1 mcast_querier 1
# ip link set dev v1 master br
# bridge vlan add dev v1 vid 2
# bridge vlan set dev v1 vid 1 mcast_max_groups 1
# bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 1
# bridge mdb add dev br port v1 grp 230.1.2.4 temp vid 1
Error: bridge: Port-VLAN is already in 1 groups, and mcast_max_groups=1.
# bridge link set dev v1 mcast_max_groups 1
# bridge mdb add dev br port v1 grp 230.1.2.3 temp vid 2
Error: bridge: Port is already in 1 groups, and mcast_max_groups=1.
# bridge -d link show
5: v1@v2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 master br [...]
[...] mcast_n_groups 1 mcast_max_groups 1
# bridge -d vlan show
port vlan-id
br 1 PVID Egress Untagged
state forwarding mcast_router 1
v1 1 PVID Egress Untagged
[...] mcast_n_groups 1 mcast_max_groups 1
2
[...] mcast_n_groups 0 mcast_max_groups 0
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch will add two more maximum MDB allowances to the global
one, mcast_hash_max, that exists today. In all these cases, attempts to add
MDB entries above the configured maximums through netlink, fail noisily and
obviously. Such visibility is missing when adding entries through the
control plane traffic, by IGMP or MLD packets.
To improve visibility in those cases, add a trace point that reports the
violation, including the relevant netdevice (be it a slave or the bridge
itself), and the MDB entry parameters:
# perf record -e bridge:br_mdb_full &
# [...]
# perf script | cut -d: -f4-
dev v2 af 2 src ::ffff:0.0.0.0 grp ::ffff:239.1.1.112/00:00:00:00:00:00 vid 0
dev v2 af 10 src :: grp ff0e::112/00:00:00:00:00:00 vid 0
dev v2 af 2 src ::ffff:0.0.0.0 grp ::ffff:239.1.1.112/00:00:00:00:00:00 vid 10
dev v2 af 10 src 2001:db8:1::1 grp ff0e::1/00:00:00:00:00:00 vid 10
dev v2 af 2 src ::ffff:192.0.2.1 grp ::ffff:239.1.1.1/00:00:00:00:00:00 vid 10
CC: Steven Rostedt <rostedt@goodmis.org>
CC: linux-trace-kernel@vger.kernel.org
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull char/misc driver fixes from Greg KH:
"Here are a number of small char/misc/whatever driver fixes. They
include:
- IIO driver fixes for some reported problems
- nvmem driver fixes
- fpga driver fixes
- debugfs memory leak fix in the hv_balloon and irqdomain code
(irqdomain change was acked by the maintainer)
All have been in linux-next with no reported problems"
* tag 'char-misc-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (33 commits)
kernel/irq/irqdomain.c: fix memory leak with using debugfs_lookup()
HV: hv_balloon: fix memory leak with using debugfs_lookup()
nvmem: qcom-spmi-sdam: fix module autoloading
nvmem: core: fix return value
nvmem: core: fix cell removal on error
nvmem: core: fix device node refcounting
nvmem: core: fix registration vs use race
nvmem: core: fix cleanup after dev_set_name()
nvmem: core: remove nvmem_config wp_gpio
nvmem: core: initialise nvmem->id early
nvmem: sunxi_sid: Always use 32-bit MMIO reads
nvmem: brcm_nvram: Add check for kzalloc
iio: imu: fxos8700: fix MAGN sensor scale and unit
iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
iio: imu: fxos8700: fix failed initialization ODR mode assignment
iio: imu: fxos8700: fix incorrect ODR mode readback
iio: light: cm32181: Fix PM support on system with 2 I2C resources
iio: hid: fix the retval in gyro_3d_capture_sample
iio: hid: fix the retval in accel_3d_capture_sample
iio: imu: st_lsm6dsx: fix build when CONFIG_IIO_TRIGGERED_BUFFER=m
...
Pull perf fix from Borislav Petkov:
- Lock the proper critical section when dealing with perf event context
* tag 'perf_urgent_for_v6.2_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix perf_event_pmu_context serialization
Pull RTC fixes from Alexandre Belloni:
"Here are a few fixes for 6.2. The EFI one is the most important as it
allows some RTCs to actually work. The other two are warnings that are
worth fixing.
- efi: make WAKEUP services optional
- sunplus: fix format string warning"
* tag 'rtc-6.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: sunplus: fix format string for printing resource
dt-bindings: rtc: qcom-pm8xxx: allow 'wakeup-source' property
rtc: efi: Enable SET/GET WAKEUP services as optional
Pull kvm fixes from Paolo Bonzini:
"ARM64:
- Yet another fix for non-CPU accesses to the memory backing the
VGICv3 subsystem
- A set of fixes for the setlftest checking for the S1PTW behaviour
after the fix that went in ealier in the cycle"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: selftests: aarch64: Test read-only PT memory regions
KVM: selftests: aarch64: Fix check of dirty log PT write
KVM: selftests: aarch64: Do not default to dirty PTE pages on all S1PTWs
KVM: selftests: aarch64: Relax userfaultfd read vs. write checks
KVM: arm64: Allow no running vcpu on saving vgic3 pending table
KVM: arm64: Allow no running vcpu on restoring vgic3 LPI pending status
KVM: arm64: Add helper vgic_write_guest_lock()
KVM/arm64 fixes for 6.2, take #3
- Yet another fix for non-CPU accesses to the memory backing
the VGICv3 subsystem
- A set of fixes for the setlftest checking for the S1PTW
behaviour after the fix that went in ealier in the cycle
When device is capable of handling scaled ppm values for adjusting
frequency, conversion to ppb will not be done by the driver. Instead, the
scaled ppm value will be passed directly to the device for the frequency
adjustment operation.
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Some applications seem to rely on RAW sockets.
If they use private netns, we can avoid piling all RAW
sockets bound to a given protocol into a single bucket.
Also place (struct raw_hashinfo).lock into its own
cache line to limit false sharing.
Alternative would be to have per-netns hashtables,
but this seems too expensive for most netns
where RAW sockets are not used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull ceph fix from Ilya Dryomov:
"A safeguard to prevent the kernel client from further damaging the
filesystem after running into a case of an invalid snap trace.
The root cause of this metadata corruption is still being investigated
but it appears to be stemming from the MDS. As such, this is the best
we can do for now"
* tag 'ceph-for-6.2-rc7' of https://github.com/ceph/ceph-client:
ceph: blocklist the kclient when receiving corrupted snap trace
ceph: move mount state enum to super.h
Pull misc fixes from Andrew Morton:
"25 hotfixes, mainly for MM. 13 are cc:stable"
* tag 'mm-hotfixes-stable-2023-02-02-19-24-2' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (26 commits)
mm: memcg: fix NULL pointer in mem_cgroup_track_foreign_dirty_slowpath()
Kconfig.debug: fix the help description in SCHED_DEBUG
mm/swapfile: add cond_resched() in get_swap_pages()
mm: use stack_depot_early_init for kmemleak
Squashfs: fix handling and sanity checking of xattr_ids count
sh: define RUNTIME_DISCARD_EXIT
highmem: round down the address passed to kunmap_flush_on_unmap()
migrate: hugetlb: check for hugetlb shared PMD in node migration
mm: hugetlb: proc: check for hugetlb shared PMD in /proc/PID/smaps
mm/MADV_COLLAPSE: catch !none !huge !bad pmd lookups
Revert "mm: kmemleak: alloc gray object for reserved region with direct map"
freevxfs: Kconfig: fix spelling
maple_tree: should get pivots boundary by type
.mailmap: update e-mail address for Eugen Hristev
mm, mremap: fix mremap() expanding for vma's with vm_ops->close()
squashfs: harden sanity check in squashfs_read_xattr_id_table
ia64: fix build error due to switch case label appearing next to declaration
mm: multi-gen LRU: fix crash during cgroup migration
Revert "mm: add nodes= arg to memory.reclaim"
zsmalloc: fix a race with deferred_handles storing
...
Modify flow table offload to cache the last ct info status that was passed
to the driver offload callbacks by extending enum nf_flow_flags with new
"NF_FLOW_HW_ESTABLISHED" flag. Set the flag if ctinfo was 'established'
during last act_ct meta actions fill call. This infrastructure change is
necessary to optimize promoting of UDP connections from 'new' to
'established' in following patches in this series.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify flow table offload to support unidirectional connections by
extending enum nf_flow_flags with new "NF_FLOW_HW_BIDIRECTIONAL" flag. Only
offload reply direction when the flag is set. This infrastructure change is
necessary to support offloading UDP NEW connections in original direction
in following patches in series.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, can and netfilter.
Current release - regressions:
- phy: fix null-deref in phy_attach_direct
- mac802154: fix possible double free upon parsing error
Previous releases - regressions:
- bpf: preserve reg parent/live fields when copying range info,
prevent mis-verification of programs as safe
- ip6: fix GRE tunnels not generating IPv6 link local addresses
- phy: dp83822: fix null-deref on DP83825/DP83826 devices
- sctp: do not check hb_timer.expires when resetting hb_timer
- eth: mtk_sock: fix SGMII configuration after phylink conversion
Previous releases - always broken:
- eth: xdp: execute xdp_do_flush() before napi_complete_done()
- skb: do not mix page pool and page referenced frags in GRO
- bpf:
- fix a possible task gone issue with bpf_send_signal[_thread]()
- fix an off-by-one bug in bpf_mem_cache_idx() to select the right
cache
- add missing btf_put to register_btf_id_dtor_kfuncs
- sockmap: fon't let sock_map_{close,destroy,unhash} call itself
- gso: fix null-deref in skb_segment_list()
- mctp: purge receive queues on sk destruction
- fix UaF caused by accept on already connected socket in exotic
socket families
- tls: don't treat list head as an entry in tls_is_tx_ready()
- netfilter: br_netfilter: disable sabotage_in hook after first
suppression
- wwan: t7xx: fix runtime PM implementation
Misc:
- MAINTAINERS: spring cleanup of networking maintainers"
* tag 'net-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
mtk_sgmii: enable PCS polling to allow SFP work
net: mediatek: sgmii: fix duplex configuration
net: mediatek: sgmii: ensure the SGMII PHY is powered down on configuration
MAINTAINERS: update SCTP maintainers
MAINTAINERS: ipv6: retire Hideaki Yoshifuji
mailmap: add John Crispin's entry
MAINTAINERS: bonding: move Veaceslav Falico to CREDITS
net: openvswitch: fix flow memory leak in ovs_flow_cmd_new
net: ethernet: mtk_eth_soc: disable hardware DSA untagging for second MAC
virtio-net: Keep stop() to follow mirror sequence of open()
selftests: net: udpgso_bench_tx: Cater for pending datagrams zerocopy benchmarking
selftests: net: udpgso_bench: Fix racing bug between the rx/tx programs
selftests: net: udpgso_bench_rx/tx: Stop when wrong CLI args are provided
selftests: net: udpgso_bench_rx: Fix 'used uninitialized' compiler warning
can: mcp251xfd: mcp251xfd_ring_set_ringparam(): assign missing tx_obj_num_coalesce_irq
can: isotp: split tx timer into transmission and timeout
can: isotp: handle wait_event_interruptible() return values
can: raw: fix CAN FD frame transmissions over CAN XL devices
can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate
hv_netvsc: Fix missed pagebuf entries in netvsc_dma_map/unmap()
...
Pull KUnit fixes from Shuah Khan:
"Three fixes to bugs that cause kernel crash, link error during build,
and a third to fix kunit_test_init_section_suites() extra indirection
issue"
* tag 'linux-kselftest-kunit-fixes-6.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: fix kunit_test_init_section_suites(...)
kunit: fix bug in KUNIT_EXPECT_MEMEQ
kunit: Export kunit_running()
