We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Note that we also fix a harmless typo for the node name, it's
dispc@400, not dispc@4000.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On am437x, the display subsystem (DSS) is on l4. We already have
the interconnect target module for it, so let's just move dss
there.
To do that, we need to adjust the module addresses for the ranges,
and use the ranges already added earlier based on reading the l4
interconnect instance AP registers.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Note that we must disable smart idle modes for HDMI audio like we've
done with the legacy platform data. And HDMI needs both hdmi clock
and dss clock to operate.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module and drop "ti,hwmods" peroperty as this module is a child node
of dispc and has no dependencies to to legacy platform data.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
We must now also configure sys_clk for reset to complete, the top
level module only keeps optional clocks enabled for it's own reset.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty until the child
devices are probing with ti-sysc interconnect driver.
The display subsystem (DSS) is in a 16MB interconnect target module
mapped to l4 and l3 buses. We are only using the l3 port as recommended
by the TRM. So there is no need to configure l4 ranges like we've done
for l4 ABE instance for example.
Initially let's just update the top level dss node to probe with ti-sysc
interconnect target module driver. The child nodes are still children
of dispc, only the node indentation changes for them now along with
using the reg range provided by top level dss.
Let's also add add a note about using only the l3 access without l4
as noted in the TRM.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRU-ICSS present on AM33xx/AM43xx/AM57xx has a very unique
SYSCFG register. The register follows the OMAP4-style SYSC_TYPE3
for Master Standby and Slave Idle, but also has two additional
unique fields - STANDBY_INIT and SUB_MWAIT. The STANDBY_INIT is
a control bit that is used to initiate a Standby sequence (when
set) and trigger a MStandby request to the SoC's PRCM module. This
same bit is also used to enable the OCP master ports (when cleared)
to allow the PRU cores to access any peripherals or memory beyond
the PRU subsystem. The SUB_MWAIT is a ready status field for the
external access.
Add support for this SYSC type. The STANDBY_INIT has to be set
during suspend, without which it results in a hang in the resume
sequence on AM33xx/AM43xx boards and requires a board reset to
come out of the hang. Any PRU applications requiring external
access are supposed to clear the STANDBY_INIT bit. Note that
the PRUSS context is lost during a suspend sequence because the
PRUSS module is reset and/or disabled.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated quirk define number and to use -ENODEV]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PRUSS module has a SYSCFG which is unique. The SYSCFG
has two additional unique fields called STANDBY_INIT and
SUB_MWAIT in addition to regular IDLE_MODE and STANDBY_MODE
fields. Add the bindings for this new sysc type.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to probe EDMA with ti-sysc interconnect target module and with
device tree data, we need to properly detect EDMA and set the flags for
SYSC_QUIRK_SWSUP_SIDLE | SYSC_QUIRK_SWSUP_MSTANDBY for tptc.
We have these flags currently set for am4 and dra7, but not for am335x.
Let's set them for all the SoCs as the tptc module should behave the
same for all of them. It's likely that am335x was never tested to idle
EDMA tptc.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset
quirk") added support for DSS reset, but is using dispc offset also for
DSS also registers as reported by Tomi Valkeinen <tomi.valkeinen@ti.com>.
Also, we're not using dispc_offset for dispc IRQSTATUS register so let's
fix that too.
Fixes: 7324a7a0d5 ("bus: ti-sysc: Implement display subsystem reset quirk")
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The display subsystem (DSS) needs the child outputs disabled for reset.
In order to prepare to probe DSS without legacy platform data, let's
implement sysc_pre_reset_quirk_dss() similar to what we have for the
platform data with omap_dss_reset().
Note that we cannot directly use the old omap_dss_reset() without
platform data callbacks and updating omap_dss_reset() to understand
struct device. And we will be dropping omap_dss_reset() anyways when
all the SoCs are probing with device tree, so let's not mess with the
legacy code at all.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to prepare probing display subsystem (DSS) with ti-sysc
interconnect target module driver and device tree data, let's
detect DSS related modules.
We need to also add reset quirk handling for DSS, but until that's
done, let's just enable the optional clock quirks for DSS and
omap4 HDMI. The rest is just naming of modules if CONFIG_DEBUG
is set.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The RTC modules on am3 and am4 need quirk handling to unlock and lock
them for reset so let's add the quirk handling based on what we already
have for legacy platform data. In later patches we will simply drop the
RTC related platform data and the old quirk handling.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to know SoC type and features for cases where the same SoC
may be installed in various versions on the same board and would need
a separate dts file otherwise for the different variants.
For example, am3703 is pin compatible with omap3630, but has sgx and
iva accelerators disabled. We must not try to access the sgx or iva
module registers on am3703, and need to set the unavailable devices
disabled early.
Let's also detect omap3430 as that is needed for display subsystem
(DSS) reset later on, and GP vs EMU or HS devices. Further SoC
specific disabled device detection can be added as needed, such as
dra71x vs dra76x rtc and usb4.
Cc: Adam Ford <aford173@gmail.com>
Cc: André Hentschel <nerv@dawncrow.de>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some cases we can have nested ti-sysc instances that may still use the
legacy "ti,hwmods" property. Let's not warn if that's the case.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are currently setting -1 for non-existing sysconfig related registers
for quirks, but setting -ENODEV elsewhere. And for matching the quirks,
we're now just ignoring the non-existing registers. This will cause issues
with misdetecting DSS registers as the hardware revision numbers can have
duplicates.
To avoid this, let's standardize on using -ENODEV also for the quirks
instead of -1. That way we can always just test for a match without adding
any more complicated logic.
Signed-off-by: Tony Lindgren <tony@atomide.com>
At least display susbsystem (DSS) has modules with no sysconfig registers
and rely on custom function for module reset handling. Let's make reset
work with that too.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clk_disable_quirk and clk_enable_quirk should really be called
pre_reset_quirk and post_reset_quirk to avoid confusion like we had
with hdq1w reset.
Let's also rename the related functions so the code is easier to follow.
Note that we also have reset_done_quirk that is needed in some cases
after checking the separate register for reset done bit.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Because of the i2c quirk we have the reset quirks named in a confusing
way. Let's fix the 1-wire quirk accordinlyg. Then let's switch to using
better naming later on.
Fixes: 4e23be473e ("bus: ti-sysc: Add support for module specific reset quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to probe display subsystem (DSS) components with ti-sysc
interconnect target module without legacy platform data and using
devicetree, we need to update dss probing a bit.
In the device tree, we will be defining the data also for the interconnect
target modules as DSS really is a private interconnect. There is some
information about that in 4460 TRM in "Figure 10-3. DSS Integration" for
example where it mentions "32-bit interconnect (SLX)".
The changes we need to make are:
1. Parse also device tree subnodes for the compatible property fixup
2. Update the component code to consider device tree subnodes
Cc: dri-devel@lists.freedesktop.org
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
Pull new zonefs file system from Damien Le Moal:
"Zonefs is a very simple file system exposing each zone of a zoned
block device as a file.
Unlike a regular file system with native zoned block device support
(e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
sequential write constraint of zoned block devices to the user. As a
result, zonefs is not a POSIX compliant file system. Its goal is to
simplify the implementation of zoned block devices support in
applications by replacing raw block device file accesses with a richer
file based API, avoiding relying on direct block device file ioctls
which may be more obscure to developers.
One example of this approach is the implementation of LSM
(log-structured merge) tree structures (such as used in RocksDB and
LevelDB) on zoned block devices by allowing SSTables to be stored in a
zone file similarly to a regular file system rather than as a range of
sectors of a zoned device. The introduction of the higher level
construct "one file is one zone" can help reducing the amount of
changes needed in the application while at the same time allowing the
use of zoned block devices with various programming languages other
than C.
Zonefs IO management implementation uses the new iomap generic code.
Zonefs has been successfully tested using a functional test suite
(available with zonefs userland format tool on github) and a prototype
implementation of LevelDB on top of zonefs"
* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Add documentation
fs: New zonefs file system
In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.
Fixes: 4e6437f12d ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cifs fixes from Steve French:
"13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:
- Important fix for multichannel and for modefromsid mounts.
- Two reconnect fixes
- Addition of SMB3 change notify support
- Backup tools fix
- A few additional minor debug improvements (tracepoints and
additional logging found useful during testing this week)"
* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
smb3: Add defines for new information level, FileIdInformation
smb3: print warning once if posix context returned on open
smb3: add one more dynamic tracepoint missing from strict fsync path
cifs: fix mode bits from dir listing when mounted with modefromsid
cifs: fix channel signing
cifs: add SMB3 change notification support
cifs: make multichannel warning more visible
cifs: fix soft mounts hanging in the reconnect code
cifs: Add tracepoints for errors on flush or fsync
cifs: log warning message (once) if out of disk space
cifs: fail i/o on soft mounts if sessionsetup errors out
smb3: fix problem with null cifs super block with previous patch
SMB3: Backup intent flag missing from some more ops
Pull vboxfs from Al Viro:
"This is the VirtualBox guest shared folder support by Hans de Goede,
with fixups for fs_parse folded in to avoid bisection hazards from
those API changes..."
* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Add VirtualBox guest shared folder (vboxsf) support
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
Pull SMP fixes from Thomas Gleixner:
"Two fixes for the SMP related functionality:
- Make the UP version of smp_call_function_single() match SMP
semantics when called for a not available CPU. Instead of emitting
a warning and assuming that the function call target is CPU0,
return a proper error code like the SMP version does.
- Remove a superfluous check in smp_call_function_many_cond()"
* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/up: Make smp_call_function_single() match SMP semantics
smp: Remove superfluous cond_func check in smp_call_function_many_cond()
Pull perf fixes from Thomas Gleixner:
"A set of fixes and improvements for the perf subsystem:
Kernel fixes:
- Install cgroup events to the correct CPU context to prevent a
potential list double add
- Prevent an integer underflow in the perf mlock accounting
- Add a missing prototype for arch_perf_update_userpage()
Tooling:
- Add a missing unlock in the error path of maps__insert() in perf
maps.
- Fix the build with the latest libbfd
- Fix the perf parser so it does not delete parse event terms, which
caused a regression for using perf with the ARM CoreSight as the
sink configuration was missing due to the deletion.
- Fix the double free in the perf CPU map merging test case
- Add the missing ustring support for the perf probe command"
* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf maps: Add missing unlock to maps__insert() error case
perf probe: Add ustring support for perf probe command
perf: Make perf able to build with latest libbfd
perf test: Fix test case Merge cpu map
perf parse: Copy string to perf_evsel_config_term
perf parse: Refactor 'struct perf_evsel_config_term'
kernel/events: Add a missing prototype for arch_perf_update_userpage()
perf/cgroups: Install cgroup events to correct cpuctx
perf/core: Fix mlock accounting in perf_mmap()
Pull timer fixes from Thomas Gleixner:
"Two small fixes for the time(r) subsystem:
- Handle a subtle race between the clocksource watchdog and a
concurrent clocksource watchdog stop/start sequence correctly to
prevent a timer double add bug.
- Fix the file path for the core time namespace file"
* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Prevent double add_timer_on() for watchdog_timer
MAINTAINERS: Correct path to time namespace source file
Pull interrupt fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for
the GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper
size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document
that the wakeup functionality is orthogonal to the irq
disable/enable mechanism"
* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
irqchip/gic-v3-its: Remove superfluous WARN_ON
irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
genirq: Clarify that irq wake state is orthogonal to enable/disable
irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
irqchip: Some Kconfig cleanup for C-SKY
irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
Pull EFI fix from Thomas Gleixner:
"A single fix for a EFI boot regression on X86 which was caused by the
recent rework of the EFI memory map parsing. On systems with invalid
memmap entries the cleanup function uses an value which cannot be
relied on in this stage. Use the actual EFI memmap entry instead"
* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix boot regression on systems with invalid memmap entries
Pull misc SCSI fixes from James Bottomley:
"Five small patches, all in drivers or doc, which missed the initial
pull request.
The qla2xxx and megaraid_sas are actual fixes and the rest are
spelling and doc changes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: fix spelling mistake "initilized" -> "initialized"
scsi: pm80xx: fix spelling mistake "to" -> "too"
scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
scsi: megaraid_sas: fixup MSIx interrupt setup during resume
scsi: qla2xxx: Fix unbound NVME response length
Pull networking fixes from David Miller:
1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.
2) Fix thermal zone registration in iwlwifi, from Andrei
Otcheretianski.
3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.
4) Use after free in mptcp, from Florian Westphal.
5) Use after free in wireguard's root_remove_peer_lists, from Eric
Dumazet.
6) Properly access packets heads in bonding alb code, from Eric
Dumazet.
7) Fix data race in skb_queue_len(), from Qian Cai.
8) Fix regression in r8169 on some chips, from Heiner Kallweit.
9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.
10) Certain kinds of set link netlink operations can cause a NULL deref
in the ipv6 addrconf code. Fix from Eric Dumazet.
11) Don't cancel uninitialized work queue in drop monitor, from Ido
Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: thunderx: use proper interface type for RGMII
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
bpf: Improve bucket_log calculation logic
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
bpf, sockhash: Synchronize_rcu before free'ing map
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
bpftool: Don't crash on missing xlated program instructions
bpf, sockmap: Check update requirements after locking
drop_monitor: Do not cancel uninitialized work item
mlxsw: spectrum_dpipe: Add missing error path
mlxsw: core: Add validation of hardware device types for MGPIR register
mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
selftests: mlxsw: Add test cases for local table route replacement
mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
net: dsa: microchip: enable module autoprobe
ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
dpaa_eth: support all modes with rate adapting PHYs
net: stmmac: update pci platform data to use phy_interface
net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
...
VirtualBox hosts can share folders with guests, this commit adds a
VFS driver implementing the Linux-guest side of this, allowing folders
exported by the host to be mounted under Linux.
This driver depends on the guest <-> host IPC functions exported by
the vboxguest driver.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
