Move function which indicates whether tunnel inner flow table is
supported from en.h to en_fs.c. It fits better right after tunnel
protocol rules definitions.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets drop counter:
Device out of buffer - counts packets which were dropped due to full
device internal receive queue.
This counter will be shown on ethtool as a new counter called
dev_out_of_buffer.
The counter is read from FW by command QUERY_VNIC_ENV.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the VF LAG is in use, round-robin the TX affinity of channels among
the different ports, if supported by the firmware. Create a set of TISes
per port, while doing round-robin of the channels over the different
sets. Let all SQs of a channel share the same set of TISes.
If lag_tx_port_affinity HCA cap bit is supported, num_lag_ports > 1 and
we aren't the LACP owner (PF in the regular use), assign the affinities,
otherwise use tx_affinity == 0 in TIS context to let the FW assign the
affinities itself. The TISes of the LACP owner are mapped only to the
native physical port.
For VFs, the starting port for round-robin is determined by its vhca_id,
because a VF may have only one channel if attached to a single-core VM.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For better modularity and code sharing.
Function internal change to be introduced in the next patches.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix a typo in 'mlx5e_refomrat_wol_mode_mlx5_to_linux' and
'mlx5e_refomrat_wol_mode_linux_to_mlx5' function names:
"refomrat" -> "reformat".
Fixes: 928cfe8745 ("net/mlx5e: Wake On LAN support")
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 HW spec and bits updates:
1) Aya exposes IP-in-IP capability in mlx5_core.
2) Maxim exposes lag tx port affinity capabilities.
3) Moshe adds VNIC_ENV internal rq counter bits.
4) ODP capabilities for DC transport
Misc updates:
5) Saeed, two compiler warnings cleanups
6) Add XRQ legacy commands opcodes
7) Use refcount_t for refcount
8) fix a -Wstringop-truncation warning
In mlx5_core initialization, query max ODP capabilities for DC transport
from FW and set as current capabilities.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
EHL DW EQOS is running on a 200MHz clock. Setting up stmmac-clk,
ptp clock and ptp_max_adj to 200MHz.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.
Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.
This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.
SERDES IRQs are also enabled for Topaz.
Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic update. We are removing the last underscore from
macros MV88E6XXX_PORT_STS_CMODE_100BASE_X and
MV88E6XXX_PORT_STS_CMODE_1000BASE_X. The 2500base-x version does not
have that underscore. Also PHY_INTERFACE_MODE_ macros do not have it
there.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding an additional serdes_get_lane implementation (for Topaz), we
can merge the implementations of other SERDES functions (powering and
IRQs). We can skip checking port numbers, since the serdes_get_lane()
methods inform if there is no lane on a port or if the lane cannot be
used for given cmode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the functions operating on the hidden debug registers
into it's own file, port_hidden.c. The functions prefix is renamed from
mv88e6390_hidden_ to mv88e6xxx_port_hidden_, to be consistent with the
rest of this driver. The macros are prefixed with MV88E6XXX_ prefix, and
are changed not to use the BIT() macro nor bit shifts, since the rest of
the port.h file does not use it.
We also add the support for setting the Block Address field when
operating hidden registers. Marvell's mdio examples for SERDES settings
on Topaz use Block Address 0x7 when reading/writing hidden registers,
and although the specification says that block must be set to 0xf, those
settings are reachable only with Block Address 0x7.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390_serdes_irq_link_sgmii IRQ handler reads the SERDES PHY
status register to determine speed, among other things. If cmode of the
port is set to 2500base-x, though, the PHY still reports 1000 Mbps (the
PHY register itself does not differentiate between 1000 Mbps and 2500
Mbps - it thinks it is running at 1000 Mbps, although clock is 2.5x
faster).
Look at the cmode and set SPEED_2500 if cmode is set to 2500base-x.
Also tell mv88e6xxx_port_setup_mac the PHY interface mode corresponding
to current cmode in terms of phy_interface_t.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c: In function mtk_handle_irq:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:1951:6: warning: variable status set but not used [-Wunused-but-set-variable]
Fixes: 296c912075 ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch barely supports traffic I/O, and it does that by repurposing
VLANs when there is no bridge that is taking control of them.
Letting DSA declare this netdev feature as supported (see
dsa_slave_create) would mean that VLAN sub-interfaces created on sja1105
switch ports will be hardware offloaded. That means that
net/8021q/vlan_core.c would install the VLAN into the filter tables of
the switch, potentially interfering with the tag_8021q VLANs.
We need to prevent that from happening and not let the 8021q core
offload VLANs to the switch hardware tables. In vlan_filtering=0 modes
of operation, the switch ports can pass through VLAN-tagged frames with
no problem.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Re-add SGMII support but now with PHYLINK API support
So the SGMII changes are more clear
* Move SGMII block setup from mtk_gmac_sgmii_path_setup() to
mtk_mac_config()
* Merge mtk_setup_hw_path() into mtk_mac_config()
* Remove mediatek,physpeed property, fixed-link supports now any speed so
speed = <2500>; is now valid with PHYLINK
* Demagic SGMII register values
* Use phylink state to setup fixed-link mode
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This convert the basics to PHYLINK API.
SGMII support is not in this patch.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from ./arch/powerpc/include/asm/paca.h:15,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./include/asm-generic/preempt.h:5,
from ./arch/powerpc/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:78,
from ./include/linux/spinlock.h:51,
from ./include/linux/wait.h:9,
from ./include/linux/completion.h:12,
from ./include/linux/mlx5/driver.h:37,
from
drivers/net/ethernet/mellanox/mlx5/core/lib/eq.h:6,
from
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:33:
In function 'strncpy',
inlined from 'mlx5_fw_tracer_save_trace' at
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:549:2,
inlined from 'mlx5_tracer_print_trace' at
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:574:2:
./include/linux/string.h:305:9: warning: '__builtin_strncpy' output may
be truncated copying 256 bytes from a string of length 511
[-Wstringop-truncation]
return __builtin_strncpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it by using the new strscpy_pad() since the commit 458a3bf82d
("lib/string: Add strscpy_pad() function") which will always
NUL-terminate the string, and avoid possibly leak data through the ring
buffer where non-admin account might enable these events through perf.
Fixes: fd1483fe1f ("net/mlx5: Add support for FW reporter dump")
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull MFD fix from Lee Jones:
"Identify potentially unused functions in rk808 driver when !PM"
* tag 'mfd-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: rk808: Make PM function declaration static
mfd: rk808: Mark pm functions __maybe_unused
Pull networking fixes from David Miller:
1) Use 32-bit index for tails calls in s390 bpf JIT, from Ilya
Leoshkevich.
2) Fix missed EPOLLOUT events in TCP, from Eric Dumazet. Same fix for
SMC from Jason Baron.
3) ipv6_mc_may_pull() should return 0 for malformed packets, not
-EINVAL. From Stefano Brivio.
4) Don't forget to unpin umem xdp pages in error path of
xdp_umem_reg(). From Ivan Khoronzhuk.
5) Fix sta object leak in mac80211, from Johannes Berg.
6) Fix regression by not configuring PHYLINK on CPU port of bcm_sf2
switches. From Florian Fainelli.
7) Revert DMA sync removal from r8169 which was causing regressions on
some MIPS Loongson platforms. From Heiner Kallweit.
8) Use after free in flow dissector, from Jakub Sitnicki.
9) Fix NULL derefs of net devices during ICMP processing across
collect_md tunnels, from Hangbin Liu.
10) proto_register() memory leaks, from Zhang Lin.
11) Set NLM_F_MULTI flag in multipart netlink messages consistently,
from John Fastabend.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
r8152: Set memory to all 0xFFs on failed reg reads
openvswitch: Fix conntrack cache with timeout
ipv4: mpls: fix mpls_xmit for iptunnel
nexthop: Fix nexthop_num_path for blackhole nexthops
net: rds: add service level support in rds-info
net: route dump netlink NLM_F_MULTI flag missing
s390/qeth: reject oversized SNMP requests
sock: fix potential memory leak in proto_register()
MAINTAINERS: Add phylink keyword to SFF/SFP/SFP+ MODULE SUPPORT
xfrm/xfrm_policy: fix dst dev null pointer dereference in collect_md mode
ipv4/icmp: fix rt dst dev null pointer dereference
openvswitch: Fix log message in ovs conntrack
bpf: allow narrow loads of some sk_reuseport_md fields with offset > 0
bpf: fix use after free in prog symbol exposure
bpf: fix precision tracking in presence of bpf2bpf calls
flow_dissector: Fix potential use-after-free on BPF_PROG_DETACH
Revert "r8169: remove not needed call to dma_sync_single_for_device"
ipv6: propagate ipv6_add_dev's error returns out of ipv6_find_idev
net/ncsi: Fix the payload copying for the request coming from Netlink
qed: Add cleanup in qed_slowpath_start()
...
Avoids:
../drivers/mfd/rk808.c:771:1: warning: symbol 'rk8xx_pm_ops' \
was not declared. Should it be static?
Fixes: 5752bc4373 ("mfd: rk808: Mark pm functions __maybe_unused")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The newly added suspend/resume functions are only used if CONFIG_PM
is enabled:
drivers/mfd/rk808.c:752:12: error: 'rk8xx_resume' defined but not used [-Werror=unused-function]
drivers/mfd/rk808.c:732:12: error: 'rk8xx_suspend' defined but not used [-Werror=unused-function]
Mark them as __maybe_unused so the compiler can silently drop them
when they are not needed.
Fixes: 586c1b4125 ("mfd: rk808: Add RK817 and RK809 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move the call to dma_sync_single_for_cpu after calling napi_alloc_skb.
This avoids calling dma_sync_single_for_cpu w/o handing control back
to device if the memory allocation should fail.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend struct flow_block_offload with "unlocked_driver_cb" flag to allow
registering and unregistering block hardware offload callbacks that do not
require caller to hold rtnl lock. Extend tcf_block with additional
lockeddevcnt counter that is incremented for each non-unlocked driver
callback attached to device. This counter is necessary to conditionally
obtain rtnl lock before calling hardware callbacks in following patches.
Register mlx5 tc block offload callbacks as "unlocked".
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_registers() blindly copies the memory written to by the
usb_control_msg() call even if the underlying urb failed.
This could lead to junk register values being read by the driver, since
some indirect callers of get_registers() ignore the return values. One
example is:
ocp_read_dword() ignores the return value of generic_ocp_read(), which
calls get_registers().
So, emulate PCI "Master Abort" behavior by setting the buffer to all
0xFFs when usb_control_msg() fails.
This patch is copied from the r8152 driver (v2.12.0) published by
Realtek (www.realtek.com).
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cirrus/cs89x0.c: In function 'cs89x0_platform_probe':
drivers/net/ethernet/cirrus/cs89x0.c:1847:20: warning:
variable 'lp' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 6751edeb87 ("cirrus: cs89x0: Use managed interfaces")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ee641b0cdb.
Actually it is not clear whether this register read is not
needed for it's HW side effects or not.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c: In function mtk_handle_irq:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:1951:6: warning: variable status set but not used [-Wunused-but-set-variable]
Fixes: 296c912075 ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull auxdisplay cleanup from Miguel Ojeda:
"Make ht16k33_fb_fix and ht16k33_fb_var constant (Nishka Dasgupta)"
* tag 'auxdisplay-for-linus-v5.3-rc7' of git://github.com/ojeda/linux:
auxdisplay: ht16k33: Make ht16k33_fb_fix and ht16k33_fb_var constant
Pull dma-mapping fixes from Christoph Hellwig:
"Two fixes for regressions in this merge window:
- select the Kconfig symbols for the noncoherent dma arch helpers on
arm if swiotlb is selected, not just for LPAE to not break then Xen
build, that uses swiotlb indirectly through swiotlb-xen
- fix the page allocator fallback in dma_alloc_contiguous if the CMA
allocation fails"
* tag 'dma-mapping-5.3-5' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: fix zone selection after an unaddressable CMA allocation
arm: select the dma-noncoherent symbols for all swiotlb builds
SFPs can report two different power values, the transmit power and the
receive power. Add labels to make it clear which is which. Also add
labels to the other sensors, VCC power supply, bias and module
temperature.
sensors(1) now shows:
sff2-isa-0000
Adapter: ISA adapter
VCC: +3.23 V
temperature: +33.4 C
TX_power: 276.00 uW
RX_power: 20.00 uW
bias: +0.01 A
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-08-23
This series contains updates to ice driver only.
Dave adds logic for the necessary bits to be set in the VSI context for
the PF_VSI and the TX_descriptors for control packets egressing the
PF_VSI. Updated the logic to detect both DCBx and LLDP states in the
firmware engine to account for situations where DCBx is enabled and LLDP
is disabled. Fixed the driver to treat the DCBx state of "NOT_STARTED"
as a valid state and should not assume "is_fw_lldp" true automatically.
Since "enable-fw-lldp" flag was confusing and cumbersome, change the
flag to "fw-lldp-agent" with a value of on or off to help clarify
whether the LLDP agent is running or not.
Brett fixes an issue where synchronize_irq() was being called from the
host of VF's, which should not be done.
Michal fixed an issue when rebuilding the DCBx configuration while in
IEEE mode versus CEE mode, so add a check before copying the
configuration value to ensure we are only in CEE mode.
Jake fixes the PF to reject any VF request to setup head writeback since
the support has been deprecated.
Mitch adds an additional check to ensure the VF is active before sending
out an error message that a message was unable to be sent to a
particular VF.
Chinh updates the driver to use "topology" mode when checking the PHY
for status, since this mode provides us the current module type that is
available. Fixes the driver from clearing the auto_fec_enable bit which
was blocking a user from forcing non-spec compliant FEC configurations.
Amruth does a refactor on the code to first check, then assign in the
virtual channel space.
Bruce updates the driver to actually update the stats when a user runs
the ethtool command 'ethtool -S <iface>' instead of providing a snapshot
of the stats that maybe from a second ago.
Akeem fixes up the adding/removing of VSI MAC filters for VFs, so that
VFs cannot add/remove a filter from another VSI. We now track the
number of filters added right from when the VF resources get allocated
and won't get into MAC filter mis-match issue in the switch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IQD devices offer limited support for bulking: all frames in a TX buffer
need to have the same target. qeth_iqd_may_bulk() implements this
constraint, and allows us to defer the TX doorbell until
(a) the buffer is full (since each buffer needs its own doorbell), or
(b) the entire TX queue is full, or
(b) we reached the BQL limit.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each TX buffer may contain multiple skbs. So just accumulate the sent
byte count in the buffer struct, and later use the same count when
completing the buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the stack to bulk-free our TX-completed skbs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to their large MTU and potentially low utilization of TX buffers,
IQD devices in particular require fast TX recycling. This makes them
a prime candidate for a TX NAPI path in qeth.
qeth_tx_poll() uses the recently introduced qdio_inspect_queue() helper
to poll the TX queue for completed buffers. To avoid hogging the CPU for
too long, we yield to the stack after completing an entire queue's worth
of buffers.
While IQD is expected to transfer its buffers synchronously (and thus
doesn't support TX interrupts), a timer covers for the odd case where a
TX buffer doesn't complete synchronously. Currently this timer should
only ever fire for
(1) the mcast queue,
(2) the occasional race, where the NAPI poll code observes an update to
queue->used_buffers while the TX doorbell hasn't been issued yet.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This consolidates the SW statistics code, and improves it to
(1) account for the header overhead of each segment on a TSO skb,
(2) count dangling packets as in-error (during eg. shutdown), and
(3) only count offloads when the skb was successfully transmitted.
We also count each segment of an TSO skb as one packet - except for
tx_dropped, to be consistent with dev->tx_dropped.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a driver wants to use the new Output Queue poll code, then the qdio
layer must disable its internal Queue scanning. Let the driver select
this mode by passing a special scan_threshold of 0.
As the scan_threshold is the same for all Output Queues, also move it
into the main qdio_irq struct. This allows for fast opt-out checking, a
driver is expected to operate either _all_ or none of its Output Queues
in polling mode.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit d36deae750 ("qdio: extend API to allow polling") enhanced
the qdio layer so that drivers can poll their Input Queues, we don't
have the corresponding infrastructure for Output Queues yet.
Factor out a helper that scans a single QDIO Queue, so that qeth can
implement TX NAPI on top of it.
While doing so, remove the duplicated tracking of the next-to-scan index
(q->first_to_check vs q->first_to_kick) in this code path.
qdio_handle_aobs() needs to move slightly upwards in the code hierarchy,
so that it's still called from the polling path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit added logic to determine the appropriate statistics block
size to allocate and the size is stored in bp->hw_ring_stats_size. But
if the firmware spec is older than 1.6.0, it is 0 and not initialized.
This causes the allocation to fail with size 0 and bnxt_open() to
abort. Fix it by always initializing bp->hw_ring_stats_size to the
legacy default size value.
Fixes: 4e74850663 ("bnxt_en: Allocate the larger per-ring statistics block for 57500 chips.")
Reported-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d4c08afafa ("s390/qeth: streamline SNMP cmd code") removed
the bounds checking for req_len, under the assumption that the check in
qeth_alloc_cmd() would suffice.
But that code path isn't sufficiently robust to handle a user-provided
data_length, which could overflow (when adding the cmd header overhead)
before being checked against QETH_BUFSIZE. We end up allocating just a
tiny iob, and the subsequent copy_from_user() writes past the end of
that iob.
Special-case this path and add a coarse bounds check, to protect against
maliciuous requests. This let's the subsequent code flow do its normal
job and precise checking, without risk of overflow.
Fixes: d4c08afafa ("s390/qeth: streamline SNMP cmd code")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-08-22
This series introduces some fixes to mlx5 driver.
1) Form Moshe, two fixes for firmware health reporter
2) From Eran, two ktls fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
warning: tuple_key_info defined but not used [-Wunused-const-variable=]
The two variable is only used in hclge_main.c,
so just move the definition over there.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull GPIO fixes from Linus Walleij:
"Here is a (hopefully last) set of GPIO fixes for the v5.3 kernel
cycle. Two are pretty core:
- Fix not reporting open drain/source lines to userspace as "input"
- Fix a minor build error found in randconfigs
- Fix a chip select quirk on the Freescale SPI
- Fix the irqchip initialization semantic order to reflect what it
was using the old API"
* tag 'gpio-v5.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Fix irqchip initialization order
gpio: of: fix Freescale SPI CS quirk handling
gpio: Fix build error of function redefinition
gpiolib: never report open-drain/source lines as 'input' to user-space
