commit 1467559232 upstream.
The output of KDB 'summary' command should report MemTotal, MemFree
and Buffers output in kB. Current codes report in unit of pages.
A define of K(x) as
is defined in the code, but not used.
This patch would apply the define to convert the values to kB.
Please include me on Cc on replies. I do not subscribe to linux-kernel.
Signed-off-by: Jay Lan <jlan@sgi.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bc78f32c2 upstream.
Add regulator_has_full_constraints() call to poodle board file to let
regulator core know that we do not have any additional regulators left.
This lets it substitute unprovided regulators with dummy ones.
This fixes the following warnings that can be seen on poodle if
regulators are enabled:
ads7846 spi1.0: unable to get regulator: -517
spi spi1.0: Driver ads7846 requests probe deferral
wm8731 0-001b: Failed to get supply 'AVDD': -517
wm8731 0-001b: Failed to request supplies: -517
wm8731 0-001b: ASoC: failed to probe component -517
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 271e80176a upstream.
Add regulator_has_full_constraints() call to corgi board file to let
regulator core know that we do not have any additional regulators left.
This lets it substitute unprovided regulators with dummy ones.
This fixes the following warnings that can be seen on corgi if
regulators are enabled:
ads7846 spi1.0: unable to get regulator: -517
spi spi1.0: Driver ads7846 requests probe deferral
wm8731 0-001b: Failed to get supply 'AVDD': -517
wm8731 0-001b: Failed to request supplies: -517
wm8731 0-001b: ASoC: failed to probe component -517
corgi-audio corgi-audio: ASoC: failed to instantiate card -517
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19e3ae6b4f upstream.
The vcs device's poll/fasync support relies on the vt notifier to signal
changes to the screen content. Notifier invocations were missing for
changes that comes through the selection interface though. Fix that.
Tested with BRLTTY 5.2.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: Dave Mielke <dave@mielke.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5efd2ea8c9 upstream.
the following error pops up during "testusb -a -t 10"
| musb-hdrc musb-hdrc.1.auto: dma_pool_free buffer-128, f134e000/be842000 (bad dma)
hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of
size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in
hcd_buffer_alloc() returning memory which is 32 bytes aligned and it
might by identified by buffer_offset() as another buffer. This means the
buffer which is on a 32 byte boundary will not get freed, instead it
tries to free another buffer with the error message.
This patch fixes the issue by creating the smallest DMA buffer with the
size of ARCH_KMALLOC_MINALIGN (or 32 in case ARCH_KMALLOC_MINALIGN is
smaller). This might be 32, 64 or even 128 bytes. The next three pools
will have the size 128, 512 and 2048.
In case the smallest pool is 128 bytes then we have only three pools
instead of four (and zero the first entry in the array).
The last pool size is always 2048 bytes which is the assumed PAGE_SIZE /
2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where
we would end up with 8KiB buffer in case we have 16KiB pages.
Instead I think it makes sense to have a common size(s) and extend them
if there is need to.
There is a BUILD_BUG_ON() now in case someone has a minalign of more than
128 bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c99197902d upstream.
The usb_hcd_unlink_urb() routine in hcd.c contains two possible
use-after-free errors. The dev_dbg() statement at the end of the
routine dereferences urb and urb->dev even though both structures may
have been deallocated.
This patch fixes the problem by storing urb->dev in a local variable
(avoiding the dereference of urb) and moving the dev_dbg() up before
the usb_put_dev() call.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37480a0568 upstream.
Commit 26df6d1340 ("tty: Add EXTPROC support for LINEMODE")
allows a process which has opened a pty master to send _any_ signal
to the process group of the pty slave. Although potentially
exploitable by a malicious program running a setuid program on
a pty slave, it's unknown if this exploit currently exists.
Limit to signals actually used.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Howard Chu <hyc@symas.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6ce194325 upstream.
Hi,
If you can manage to submit an async write as the first async I/O from
the context of a process with realtime scheduling priority, then a
cfq_queue is allocated, but filed into the wrong async_cfqq bucket. It
ends up in the best effort array, but actually has realtime I/O
scheduling priority set in cfqq->ioprio.
The reason is that cfq_get_queue assumes the default scheduling class and
priority when there is no information present (i.e. when the async cfqq
is created):
static struct cfq_queue *
cfq_get_queue(struct cfq_data *cfqd, bool is_sync, struct cfq_io_cq *cic,
struct bio *bio, gfp_t gfp_mask)
{
const int ioprio_class = IOPRIO_PRIO_CLASS(cic->ioprio);
const int ioprio = IOPRIO_PRIO_DATA(cic->ioprio);
cic->ioprio starts out as 0, which is "invalid". So, class of 0
(IOPRIO_CLASS_NONE) is passed to cfq_async_queue_prio like so:
async_cfqq = cfq_async_queue_prio(cfqd, ioprio_class, ioprio);
static struct cfq_queue **
cfq_async_queue_prio(struct cfq_data *cfqd, int ioprio_class, int ioprio)
{
switch (ioprio_class) {
case IOPRIO_CLASS_RT:
return &cfqd->async_cfqq[0][ioprio];
case IOPRIO_CLASS_NONE:
ioprio = IOPRIO_NORM;
/* fall through */
case IOPRIO_CLASS_BE:
return &cfqd->async_cfqq[1][ioprio];
case IOPRIO_CLASS_IDLE:
return &cfqd->async_idle_cfqq;
default:
BUG();
}
}
Here, instead of returning a class mapped from the process' scheduling
priority, we get back the bucket associated with IOPRIO_CLASS_BE.
Now, there is no queue allocated there yet, so we create it:
cfqq = cfq_find_alloc_queue(cfqd, is_sync, cic, bio, gfp_mask);
That function ends up doing this:
cfq_init_cfqq(cfqd, cfqq, current->pid, is_sync);
cfq_init_prio_data(cfqq, cic);
cfq_init_cfqq marks the priority as having changed. Then, cfq_init_prio
data does this:
ioprio_class = IOPRIO_PRIO_CLASS(cic->ioprio);
switch (ioprio_class) {
default:
printk(KERN_ERR "cfq: bad prio %x\n", ioprio_class);
case IOPRIO_CLASS_NONE:
/*
* no prio set, inherit CPU scheduling settings
*/
cfqq->ioprio = task_nice_ioprio(tsk);
cfqq->ioprio_class = task_nice_ioclass(tsk);
break;
So we basically have two code paths that treat IOPRIO_CLASS_NONE
differently, which results in an RT async cfqq filed into a best effort
bucket.
Attached is a patch which fixes the problem. I'm not sure how to make
it cleaner. Suggestions would be welcome.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Tested-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69abaffec7 upstream.
Cfq_lookup_create_cfqg() allocates struct blkcg_gq using GFP_ATOMIC.
In cfq_find_alloc_queue() possible allocation failure is not handled.
As a result kernel oopses on NULL pointer dereference when
cfq_link_cfqq_cfqg() calls cfqg_get() for NULL pointer.
Bug was introduced in v3.5 in commit cd1604fab4 ("blkcg: factor
out blkio_group creation"). Prior to that commit cfq group lookup
had returned pointer to root group as fallback.
This patch handles this error using existing fallback oom_cfqq.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Fixes: cd1604fab4 ("blkcg: factor out blkio_group creation")
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8ba1f9714 upstream.
If the call to decode_rc_list() fails due to a memory allocation error,
then we need to truncate the array size to ensure that we only call
kfree() on those pointer that were allocated.
Reported-by: David Ramos <daramos@stanford.edu>
Fixes: 4aece6a19c ("nfs41: cb_sequence xdr implementation")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb71f8a5e3 upstream.
The tpm_ibmvtpm module is affected by an unaligned access problem.
ibmvtpm_crq_get_version failed with rc=-4 during boot when vTPM is
enabled in Power partition, which supports both little endian and
big endian modes.
We added little endian support to fix this problem:
1) added cpu_to_be64 calls to ensure BE data is sent from an LE OS.
2) added be16_to_cpu and be32_to_cpu calls to make sure data received
is in LE format on a LE OS.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
[phuewe: manually applied the patch :( ]
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ba3b0b6f2 upstream.
When sending data in tpm_stm_i2c_send, each loop iteration send buf.
Send buf + i instead as the goal of this for loop is to send a number
of byte from buf that fit in burstcnt. Once those byte are sent, we are
supposed to send the next ones.
The driver was working because the burstcount value returns always the maximum size for a TPM
command or response. (0x800 for a command and 0x400 for a response).
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84eb186bc3 upstream.
There was an oops in tpm_ibmvtpm_get_desired_dma, which caused
kernel panic during boot when vTPM is enabled in Power partition
configured in AMS mode.
vio_bus_probe calls vio_cmo_bus_probe which calls
tpm_ibmvtpm_get_desired_dma to get the size needed for DMA allocation.
The problem is, vio_cmo_bus_probe is called before calling probe, which
for vtpm is tpm_ibmvtpm_probe and it's this function that initializes
and sets up vtpm's CRQ and gets required data values. Therefore,
since this has not yet been done, NULL is returned in attempt to get
the size for DMA allocation.
We added a NULL check. In addition, a default buffer size will
be set when NULL is returned.
Signed-off-by: Hon Ching (Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 448e9c55c1 upstream.
Some machines, such as the Acer C720 and Toshiba CB35, have TPMs that do
not send IRQs while also having an ACPI TPM entry indicating that they
will be sent. These machines freeze on resume while the tpm_tis module
waits for an IRQ, eventually timing out.
When in interrupt mode, the tpm_tis module should receive an IRQ during
module init. Fall back to polling mode if none is received when expected.
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor checkpatch fixed]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e461894dc2 upstream.
StrongARM core uses RCSR SMR bit to tell to bootloader that it was reset
by entering the sleep mode. After we have resumed, there is little point
in having that bit enabled. Moreover, if this bit is set before reboot,
the bootloader can become confused. Thus clear the SMR bit on resume
just before clearing the scratchpad (resume address) register.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ffa30d3f7 upstream.
Bruce reported seeing this warning pop when mounting using v4.1:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1121 at kernel/sched/core.c:7300 __might_sleep+0xbd/0xd0()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff810ff58f>] prepare_to_wait+0x2f/0x90
Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc fscache ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw snd_hda_codec_generic snd_hda_intel snd_hda_controller snd_hda_codec snd_hwdep snd_pcm snd_timer ppdev joydev snd virtio_console virtio_balloon pcspkr serio_raw parport_pc parport pvpanic floppy soundcore i2c_piix4 virtio_blk virtio_net qxl drm_kms_helper ttm drm virtio_pci virtio_ring ata_generic virtio pata_acpi
CPU: 1 PID: 1121 Comm: nfsv4.1-svc Not tainted 3.19.0-rc4+ #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153950- 04/01/2014
0000000000000000 000000004e5e3f73 ffff8800b998fb48 ffffffff8186ac78
0000000000000000 ffff8800b998fba0 ffff8800b998fb88 ffffffff810ac9da
ffff8800b998fb68 ffffffff81c923e7 00000000000004d9 0000000000000000
Call Trace:
[<ffffffff8186ac78>] dump_stack+0x4c/0x65
[<ffffffff810ac9da>] warn_slowpath_common+0x8a/0xc0
[<ffffffff810aca65>] warn_slowpath_fmt+0x55/0x70
[<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90
[<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90
[<ffffffff810dd2ad>] __might_sleep+0xbd/0xd0
[<ffffffff8124c973>] kmem_cache_alloc_trace+0x243/0x430
[<ffffffff810d941e>] ? groups_alloc+0x3e/0x130
[<ffffffff810d941e>] groups_alloc+0x3e/0x130
[<ffffffffa0301b1e>] svcauth_unix_accept+0x16e/0x290 [sunrpc]
[<ffffffffa0300571>] svc_authenticate+0xe1/0xf0 [sunrpc]
[<ffffffffa02fc564>] svc_process_common+0x244/0x6a0 [sunrpc]
[<ffffffffa02fd044>] bc_svc_process+0x1c4/0x260 [sunrpc]
[<ffffffffa03d5478>] nfs41_callback_svc+0x128/0x1f0 [nfsv4]
[<ffffffff810ff970>] ? wait_woken+0xc0/0xc0
[<ffffffffa03d5350>] ? nfs4_callback_svc+0x60/0x60 [nfsv4]
[<ffffffff810d45bf>] kthread+0x11f/0x140
[<ffffffff810ea815>] ? local_clock+0x15/0x30
[<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250
[<ffffffff81874bfc>] ret_from_fork+0x7c/0xb0
[<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250
---[ end trace 675220a11e30f4f2 ]---
nfs41_callback_svc does most of its work while in TASK_INTERRUPTIBLE,
which is just wrong. Fix that by finishing the wait immediately if we've
found that the list has something on it.
Also, we don't expect this kthread to accept signals, so we should be
using a TASK_UNINTERRUPTIBLE sleep instead. That however, opens us up
hung task warnings from the watchdog, so have the schedule_timeout
wake up every 60s if there's no callback activity.
Reported-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14460dbaf7 upstream.
Current code checks "clk_delay_cycles > 0" to know whether the optional
"mrvl,clk_delay_cycles" is set or not. But of_property_read_u32() doesn't
touch clk_delay_cycles if the property is not set. And type of
clk_delay_cycles is u32, so we may always set pdata->clk_delay_cycles as a
random value.
This patch fix this problem by check the return value of of_property_read_u32()
to know whether the optional clk-delay-cycles is set or not.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24727b45b4 upstream.
Driver forgot to unregister power supply if request_threaded_irq()
failed in probe(). In such case the memory associated with power supply
leaked.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: a830d28b48 ("power_supply: Enable battery-charger for 88pm860x")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0153c3d94 upstream.
RME RayDAT and AIO use a fixed buffer size of 16384 samples. With period
sizes of 32-4096, this translates to 4-512 periods.
The older RME cards have a variable buffer size but require exactly two
periods.
This patch enforces nperiods=2 on those cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4940626de upstream.
The problem here is that we check:
if (dev >= SNDRV_CARDS)
Then we increment "dev".
if (!joystick_port[dev++])
Then we use it as an offset into a array with SNDRV_CARDS elements.
if (!request_region(joystick_port[dev], 8, "Riptide gameport")) {
This has 3 effects:
1) If you use the module option to specify the joystick port then it has
to be shifted one space over.
2) The wrong error message will be printed on failure if you have over
32 cards.
3) Static checkers will correctly complain that are off by one.
Fixes: db1005ec6f ('ALSA: riptide - Fix joystick resource handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15e1ce3318 upstream.
A quirk of some older firmwares that report endpoint pipe type as PIPE_BULK
but the endpoint otheriwse functions as interrupt.
Check if usb_endpoint_type is USB_ENDPOINT_XFER_BULK and set as usb_rcvbulkpipe.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4d4eda237 upstream.
On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the
speedstep-smi driver sometimes loads and sometimes doesn't load with
"change to state X failed" message.
The hardware sometimes refuses to change frequency and in this case, we
need to retry later. I found out that we need to enable interrupts while
waiting. When we enable interrupts, the hardware blockage that prevents
frequency transition resolves and the transition is possible. With
disabled interrupts, the blockage doesn't resolve (no matter how long do
we wait). The exact reasons for this hardware behavior are unknown.
This patch enables interrupts in the function speedstep_set_state that can
be called with disabled interrupts. However, this function is called with
disabled interrupts only from speedstep_get_freqs, so it shouldn't cause
any problem.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 145b3fe579 upstream.
Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.
The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D. Most interface types defined in the spec do not use
alpha characters, so they won't be affected. For example, 00h, 01h, 10h,
20h, etc. are unaffected.
Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.
Commit 89ec3dcf17 ("PCI: Generate uppercase hex for modalias interface
class") fixed only half of the problem. Some udev implementations rely on
the uevent file and not the modalias file.
Fixes: d1ded203ad ("PCI: add MODALIAS to hotplug event for pci devices")
Fixes: 89ec3dcf17 ("PCI: Generate uppercase hex for modalias interface class")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d00f37e49 upstream.
d1c7e29e8d (HID: i2c-hid: prevent buffer overflow in early IRQ)
changed hid_get_input() to read ihid->bufsize bytes, which can be
more than wMaxInputLength. This is the case with the Dell XPS 13
9343, and it is causing events to be missed. In some cases the
missed events are releases, which can cause the cursor to jump or
freeze, among other problems. Limit the number of bytes read to
min(wMaxInputLength, ihid->bufsize) to prevent such problems.
Fixes: d1c7e29e8d "HID: i2c-hid: prevent buffer overflow in early IRQ"
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5523d11cc4 upstream.
We don't really need to use different mac colors when adding mac
contexts, because they're not used anywhere. In fact, the firmware
doesn't accept 255 as a valid color, so we get into a SYSASSERT 0x3401
when we reach that.
Remove the color increment to use always zero and avoid reaching 255.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cee4762c5 upstream.
These are coming from the FW and are used to access arrays.
Bad values can cause an out of bounds access so discard
such ba_notifs and warn.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd8f438405 upstream.
The base address of the scheduler in the device's memory
(SRAM) comes from two different sources. The periphery
register and the alive notification from the firmware.
We have a check in iwl_pcie_tx_start that ensures that
they are the same.
When we resume from WoWLAN, the firmware may have crashed
for whatever reason. In that case, the whole device may be
reset which means that the periphery register will hold a
meaningless value. When we come to compare
trans_pcie->scd_base_addr (which really holds the value we
had when we loaded the WoWLAN firmware upon suspend) and
the current value of the register, we don't see a match
unsurprisingly.
Trick the check to avoid a loud yet harmless WARN.
Note that when the WoWLAN has crashed, we will see that
in iwl_trans_pcie_d3_resume which will let the op_mode
know. Once the op_mode is informed that the WowLAN firmware
has crashed, it can't do much besides resetting the whole
device.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ee8e25fc3 upstream.
Commit e9fd702a58 ("audit: convert audit watches to use fsnotify
instead of inotify") broke handling of renames in audit. Audit code
wants to update inode number of an inode corresponding to watched name
in a directory. When something gets renamed into a directory to a
watched name, inotify previously passed moved inode to audit code
however new fsnotify code passes directory inode where the change
happened. That confuses audit and it starts watching parent directory
instead of a file in a directory.
This can be observed for example by doing:
cd /tmp
touch foo bar
auditctl -w /tmp/foo
touch foo
mv bar foo
touch foo
In audit log we see events like:
type=CONFIG_CHANGE msg=audit(1423563584.155:90): auid=1000 ses=2 op="updated rules" path="/tmp/foo" key=(null) list=4 res=1
...
type=PATH msg=audit(1423563584.155:91): item=2 name="bar" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE
type=PATH msg=audit(1423563584.155:91): item=3 name="foo" inode=1046842 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE
type=PATH msg=audit(1423563584.155:91): item=4 name="foo" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=CREATE
...
and that's it - we see event for the first touch after creating the
audit rule, we see events for rename but we don't see any event for the
last touch. However we start seeing events for unrelated stuff
happening in /tmp.
Fix the problem by passing moved inode as data in the FS_MOVED_FROM and
FS_MOVED_TO events instead of the directory where the change happens.
This doesn't introduce any new problems because noone besides
audit_watch.c cares about the passed value:
fs/notify/fanotify/fanotify.c cares only about FSNOTIFY_EVENT_PATH events.
fs/notify/dnotify/dnotify.c doesn't care about passed 'data' value at all.
fs/notify/inotify/inotify_fsnotify.c uses 'data' only for FSNOTIFY_EVENT_PATH.
kernel/audit_tree.c doesn't care about passed 'data' at all.
kernel/audit_watch.c expects moved inode as 'data'.
Fixes: e9fd702a58 ("audit: convert audit watches to use fsnotify instead of inotify")
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3443a3bca5 upstream.
When the superblock is modified in a transaction, the commonly
modified fields are not actually copied to the superblock buffer to
avoid the buffer lock becoming a serialisation point. However, there
are some other operations that modify the superblock fields within
the transaction that don't directly log to the superblock but rely
on the changes to be applied during the transaction commit (to
minimise the buffer lock hold time).
When we do this, we fail to mark the buffer log item as being a
superblock buffer and that can lead to the buffer not being marked
with the corect type in the log and hence causing recovery issues.
Fix it by setting the type correctly, similar to xfs_mod_sb()...
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f19b872b08 upstream.
This leads to log recovery throwing errors like:
XFS (md0): Mounting V5 Filesystem
XFS (md0): Starting recovery (logdev: internal)
XFS (md0): Unknown buffer type 0!
XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1
ffff8800ffc53800: 58 41 47 49 .....
Which is the AGI buffer magic number.
Ensure that we set the type appropriately in both unlink list
addition and removal.
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d612fb570 upstream.
Jan Kara reported that log recovery was finding buffers with invalid
types in them. This should not happen, and indicates a bug in the
logging of buffers. To catch this, add asserts to the buffer
formatting code to ensure that the buffer type is in range when the
transaction is committed.
We don't set a type on buffers being marked stale - they are not
going to get replayed, the format item exists only for recovery to
be able to prevent replay of the buffer, so the type does not
matter. Hence that needs special casing here.
Reported-by: Jan Kara <jack@suse.cz>
Tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c561a5753d upstream.
BugLink: https://bugs.launchpad.net/bugs/1400215
ath3k devices fail to load firmwares on xHCI buses, but work well on
EHCI, this might be a compatibility issue between xHCI and ath3k chips.
As my testing result, those chips will work on xHCI buses again with
this patch.
This workaround is from Qualcomm, they also did some workarounds in
Windows driver.
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 638c323c4d upstream.
Olivier Bonvalet reported having repeated crashes due to a failed
assertion he was hitting in rbd_img_obj_callback():
Assertion failure in rbd_img_obj_callback() at line 2165:
rbd_assert(which >= img_request->next_completion);
With a lot of help from Olivier with reproducing the problem
we were able to determine the object and image requests had
already been completed (and often freed) at the point the
assertion failed.
There was a great deal of discussion on the ceph-devel mailing list
about this. The problem only arose when there were two (or more)
object requests in an image request, and the problem was always
seen when the second request was being completed.
The problem is due to a race in the window between setting the
"done" flag on an object request and checking the image request's
next completion value. When the first object request completes, it
checks to see if its successor request is marked "done", and if
so, that request is also completed. In the process, the image
request's next_completion value is updated to reflect that both
the first and second requests are completed. By the time the
second request is able to check the next_completion value, it
has been set to a value *greater* than its own "which" value,
which caused an assertion to fail.
Fix this problem by skipping over any completion processing
unless the completing object request is the next one expected.
Test only for inequality (not >=), and eliminate the bad
assertion.
Tested-by: Olivier Bonvalet <ob@daevel.fr>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8f29e89f2 upstream.
Userspace expects to see a long space before the first pulse is sent on
the lirc device. Currently, if a long time has passed and a new packet
is started, the lirc codec just returns and doesn't send anything. This
makes lircd ignore many perfectly valid signals unless they are sent in
quick sucession. When a reset event is delivered, we cannot know
anything about the duration of the space. But it should be safe to
assume it has been a long time and we just set the duration to maximum.
Signed-off-by: Austin Lund <austin.lund@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cfbf654efc ]
When making use of RFC5061, section 4.2.4. for setting the primary IP
address, we're passing a wrong parameter header to param_type2af(),
resulting always in NULL being returned.
At this point, param.p points to a sctp_addip_param struct, containing
a sctp_paramhdr (type = 0xc004, length = var), and crr_id as a correlation
id. Followed by that, as also presented in RFC5061 section 4.2.4., comes
the actual sctp_addr_param, which also contains a sctp_paramhdr, but
this time with the correct type SCTP_PARAM_IPV{4,6}_ADDRESS that
param_type2af() can make use of. Since we already hold a pointer to
addr_param from previous line, just reuse it for param_type2af().
Fixes: d6de309759 ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Saran Maruti Ramanara <saran.neti@telus.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e2a4800e75 ]
When we've run out of space in the output buffer to store more data, we
will call zlib_deflate with a NULL output buffer until we've consumed
remaining input.
When this happens, olen contains the size the output buffer would have
consumed iff we'd have had enough room.
This can later cause skb_over_panic when ppp_generic skb_put()s
the returned length.
Reported-by: Iain Douglas <centos@1n6.org.uk>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bdbbb8527b ]
In commit be9f4a44e7 ("ipv4: tcp: remove per net tcp_sock")
I tried to address contention on a socket lock, but the solution
I chose was horrible :
commit 3a7c384ffd ("ipv4: tcp: unicast_sock should not land outside
of TCP stack") addressed a selinux regression.
commit 0980e56e50 ("ipv4: tcp: set unicast_sock uc_ttl to -1")
took care of another regression.
commit b5ec8eeac4 ("ipv4: fix ip_send_skb()") fixed another regression.
commit 811230cd85 ("tcp: ipv4: initialize unicast_sock sk_pacing_rate")
was another shot in the dark.
Really, just use a proper socket per cpu, and remove the skb_orphan()
call, to re-enable flow control.
This solves a serious problem with FQ packet scheduler when used in
hostile environments, as we do not want to allocate a flow structure
for every RST packet sent in response to a spoofed packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 811230cd85 ]
When I added sk_pacing_rate field, I forgot to initialize its value
in the per cpu unicast_sock used in ip_send_unicast_reply()
This means that for sch_fq users, RST packets, or ACK packets sent
on behalf of TIME_WAIT sockets might be sent to slowly or even dropped
once we reach the per flow limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 95bd09eb27 ("tcp: TSO packets automatic sizing")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59ccaaaa49 ]
Reported in: https://bugzilla.kernel.org/show_bug.cgi?id=92081
This patch avoids calling rtnl_notify if the device ndo_bridge_getlink
handler does not return any bytes in the skb.
Alternately, the skb->len check can be moved inside rtnl_notify.
For the bridge vlan case described in 92081, there is also a fix needed
in bridge driver to generate a proper notification. Will fix that in
subsequent patch.
v2: rebase patch on net tree
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6e9e16e614 ]
Lubomir Rintel reported that during replacing a route the interface
reference counter isn't correctly decremented.
To quote bug <https://bugzilla.kernel.org/show_bug.cgi?id=91941>:
| [root@rhel7-5 lkundrak]# sh -x lal
| + ip link add dev0 type dummy
| + ip link set dev0 up
| + ip link add dev1 type dummy
| + ip link set dev1 up
| + ip addr add 2001:db8:8086::2/64 dev dev0
| + ip route add 2001:db8:8086::/48 dev dev0 proto static metric 20
| + ip route add 2001:db8:8088::/48 dev dev1 proto static metric 10
| + ip route replace 2001:db8:8086::/48 dev dev1 proto static metric 20
| + ip link del dev0 type dummy
| Message from syslogd@rhel7-5 at Jan 23 10:54:41 ...
| kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2
|
| Message from syslogd@rhel7-5 at Jan 23 10:54:51 ...
| kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2
During replacement of a rt6_info we must walk all parent nodes and check
if the to be replaced rt6_info got propagated. If so, replace it with
an alive one.
Fixes: 4a287eba2d ("IPv6 routing, NLM_F_* flag support: REPLACE and EXCL flags support, warn about missing CREATE flag")
Reported-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fc752f1f43 ]
An exception is seen in ICMP ping receive path where the skb
destructor sock_rfree() tries to access a freed socket. This happens
because ping_rcv() releases socket reference with sock_put() and this
internally frees up the socket. Later icmp_rcv() will try to free the
skb and as part of this, skb destructor is called and which leads
to a kernel panic as the socket is freed already in ping_rcv().
-->|exception
-007|sk_mem_uncharge
-007|sock_rfree
-008|skb_release_head_state
-009|skb_release_all
-009|__kfree_skb
-010|kfree_skb
-011|icmp_rcv
-012|ip_local_deliver_finish
Fix this incorrect free by cloning this skb and processing this cloned
skb instead.
This patch was suggested by Eric Dumazet
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86f3cddbc3 ]
While working on rhashtable walking I noticed that the UDP diag
dumping code is buggy. In particular, the socket skipping within
a chain never happens, even though we record the number of sockets
that should be skipped.
As this code was supposedly copied from TCP, this patch does what
TCP does and resets num before we walk a chain.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
