[ Upstream commit 6bbe2a90a0 ]
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b305dfe2e9 ]
The default RGB quantization range for BT.2020 is full range (just as for
all the other RGB pixel encodings), not limited range.
Update the V4L2_MAP_QUANTIZATION_DEFAULT macro and documentation
accordingly.
Also mention that HSV is always full range and cannot be limited range.
When RGB BT2020 was introduced in V4L2 it was not clear whether it should
be limited or full range, but full range is the right (and consistent)
choice.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 54c9de8989 upstream.
In order to avoid tight event channel related IRQ loops add a new
framework of "late EOI" handling: the IRQ the event channel is bound
to will be masked until the event has been handled and the related
driver is capable to handle another event. The driver is responsible
for unmasking the event channel via the new function xen_irq_lateeoi().
This is similar to binding an event channel to a threaded IRQ, but
without having to structure the driver accordingly.
In order to support a future special handling in case a rogue guest
is sending lots of unsolicited events, add a flag to xen_irq_lateeoi()
which can be set by the caller to indicate the event was a spurious
one.
This is part of XSA-332.
Cc: stable@vger.kernel.org
Reported-by: Julien Grall <julien@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b01531db6c upstream.
->lookup() in an encrypted directory begins as follows:
1. fscrypt_prepare_lookup():
a. Try to load the directory's encryption key.
b. If the key is unavailable, mark the dentry as a ciphertext name
via d_flags.
2. fscrypt_setup_filename():
a. Try to load the directory's encryption key.
b. If the key is available, encrypt the name (treated as a plaintext
name) to get the on-disk name. Otherwise decode the name
(treated as a ciphertext name) to get the on-disk name.
But if the key is concurrently added, it may be found at (2a) but not at
(1a). In this case, the dentry will be wrongly marked as a ciphertext
name even though it was actually treated as plaintext.
This will cause the dentry to be wrongly invalidated on the next lookup,
potentially causing problems. For example, if the racy ->lookup() was
part of sys_mount(), then the new mount will be detached when anything
tries to access it. This is despite the mountpoint having a plaintext
path, which should remain valid now that the key was added.
Of course, this is only possible if there's a userspace race. Still,
the additional kernel-side race is confusing and unexpected.
Close the kernel-side race by changing fscrypt_prepare_lookup() to also
set the on-disk filename (step 2b), consistent with the d_flags update.
Fixes: 28b4c26396 ("ext4 crypto: revalidate dentry after adding or removing the key")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 968dd6d0c6 upstream.
Close some race conditions where fscrypt allowed rename() and link() on
ciphertext dentries that had been looked up just prior to the key being
concurrently added. It's better to return -ENOKEY in this case.
This avoids doing the nonsensical thing of encrypting the names a second
time when searching for the actual on-disk dir entries. It also
guarantees that DCACHE_ENCRYPTED_NAME dentries are never rename()d, so
the dcache won't have support all possible combinations of moving
DCACHE_ENCRYPTED_NAME around during __d_move().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cc248684d upstream.
Make various improvements to fscrypt dentry revalidation:
- Don't try to handle the case where the per-directory key is removed,
as this can't happen without the inode (and dentries) being evicted.
- Flag ciphertext dentries rather than plaintext dentries, since it's
ciphertext dentries that need the special handling.
- Avoid doing unnecessary work for non-ciphertext dentries.
- When revalidating ciphertext dentries, try to set up the directory's
i_crypt_info to make sure the key is really still absent, rather than
invalidating all negative dentries as the previous code did. An old
comment suggested we can't do this for locking reasons, but AFAICT
this comment was outdated and it actually works fine.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5e55e777c upstream.
Currently, trying to rename or link a regular file, directory, or
symlink into an encrypted directory fails with EPERM when the source
file is unencrypted or is encrypted with a different encryption policy,
and is on the same mountpoint. It is correct for the operation to fail,
but the choice of EPERM breaks tools like 'mv' that know to copy rather
than rename if they see EXDEV, but don't know what to do with EPERM.
Our original motivation for EPERM was to encourage users to securely
handle their data. Encrypting files by "moving" them into an encrypted
directory can be insecure because the unencrypted data may remain in
free space on disk, where it can later be recovered by an attacker.
It's much better to encrypt the data from the start, or at least try to
securely delete the source data e.g. using the 'shred' program.
However, the current behavior hasn't been effective at achieving its
goal because users tend to be confused, hack around it, and complain;
see e.g. https://github.com/google/fscrypt/issues/76. And in some cases
it's actually inconsistent or unnecessary. For example, 'mv'-ing files
between differently encrypted directories doesn't work even in cases
where it can be secure, such as when in userspace the same passphrase
protects both directories. Yet, you *can* already 'mv' unencrypted
files into an encrypted directory if the source files are on a different
mountpoint, even though doing so is often insecure.
There are probably better ways to teach users to securely handle their
files. For example, the 'fscrypt' userspace tool could provide a
command that migrates unencrypted files into an encrypted directory,
acting like 'shred' on the source files and providing appropriate
warnings depending on the type of the source filesystem and disk.
Receiving errors on unimportant files might also force some users to
disable encryption, thus making the behavior counterproductive. It's
desirable to make encryption as unobtrusive as possible.
Therefore, change the error code from EPERM to EXDEV so that tools
looking for EXDEV will fall back to a copy.
This, of course, doesn't prevent users from still doing the right things
to securely manage their files. Note that this also matches the
behavior when a file is renamed between two project quota hierarchies;
so there's precedent for using EXDEV for things other than mountpoints.
xfstests generic/398 will require an update with this change.
[Rewritten from an earlier patch series by Michael Halcrow.]
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Joe Richey <joerichey@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7010645ba7 ]
trace-cmd report doesn't show events from target subsystem because
scsi_command_size() leaks through event format string:
[target:target_sequencer_start] function scsi_command_size not defined
[target:target_cmd_complete] function scsi_command_size not defined
Addition of scsi_command_size() to plugin_scsi.c in trace-cmd doesn't
help because an expression is used inside TP_printk(). trace-cmd event
parser doesn't understand minus sign inside [ ]:
Error: expected ']' but read '-'
Rather than duplicating kernel code in plugin_scsi.c, provide a dedicated
field for CONTROL byte.
Link: https://lore.kernel.org/r/20200929125957.83069-1-r.bolshakov@yadro.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4947e84f2 ]
The various array_size functions use SIZE_MAX define, but missed limits.h
causes to failure to compile code that needs overflow.h.
In file included from drivers/infiniband/core/uverbs_std_types_device.c:6:
./include/linux/overflow.h: In function 'array_size':
./include/linux/overflow.h:258:10: error: 'SIZE_MAX' undeclared (first use in this function)
258 | return SIZE_MAX;
| ^~~~~~~~
Fixes: 610b15c50e ("overflow.h: Add allocation size calculation helpers")
Link: https://lore.kernel.org/r/20200913102928.134985-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67197a4f28 ]
Currently __set_oom_adj loops through all processes in the system to keep
oom_score_adj and oom_score_adj_min in sync between processes sharing
their mm. This is done for any task with more that one mm_users, which
includes processes with multiple threads (sharing mm and signals).
However for such processes the loop is unnecessary because their signal
structure is shared as well.
Android updates oom_score_adj whenever a tasks changes its role
(background/foreground/...) or binds to/unbinds from a service, making it
more/less important. Such operation can happen frequently. We noticed
that updates to oom_score_adj became more expensive and after further
investigation found out that the patch mentioned in "Fixes" introduced a
regression. Using Pixel 4 with a typical Android workload, write time to
oom_score_adj increased from ~3.57us to ~362us. Moreover this regression
linearly depends on the number of multi-threaded processes running on the
system.
Mark the mm with a new MMF_MULTIPROCESS flag bit when task is created with
(CLONE_VM && !CLONE_THREAD && !CLONE_VFORK). Change __set_oom_adj to use
MMF_MULTIPROCESS instead of mm_users to decide whether oom_score_adj
update should be synchronized between multiple processes. To prevent
races between clone() and __set_oom_adj(), when oom_score_adj of the
process being cloned might be modified from userspace, we use
oom_adj_mutex. Its scope is changed to global.
The combination of (CLONE_VM && !CLONE_THREAD) is rarely used except for
the case of vfork(). To prevent performance regressions of vfork(), we
skip taking oom_adj_mutex and setting MMF_MULTIPROCESS when CLONE_VFORK is
specified. Clearing the MMF_MULTIPROCESS flag (when the last process
sharing the mm exits) is left out of this patch to keep it simple and
because it is believed that this threading model is rare. Should there
ever be a need for optimizing that case as well, it can be done by hooking
into the exit path, likely following the mm_update_next_owner pattern.
With the combination of (CLONE_VM && !CLONE_THREAD && !CLONE_VFORK) being
quite rare, the regression is gone after the change is applied.
[surenb@google.com: v3]
Link: https://lkml.kernel.org/r/20200902012558.2335613-1-surenb@google.com
Fixes: 44a70adec9 ("mm, oom_adj: make sure processes sharing mm have same view of oom_score_adj")
Reported-by: Tim Murray <timmurray@google.com>
Suggested-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Eugene Syromiatnikov <esyr@redhat.com>
Cc: Christian Kellner <christian@kellner.me>
Cc: Adrian Reber <areber@redhat.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Aleksa Sarai <cyphar@cyphar.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alexey Gladkov <gladkov.alexey@gmail.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Bernd Edlinger <bernd.edlinger@hotmail.de>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Yafang Shao <laoar.shao@gmail.com>
Link: https://lkml.kernel.org/r/20200824153036.3201505-1-surenb@google.com
Debugged-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d9826bc18 ]
Dump vlan tag and proto for the usual vlan offload case if the
NF_LOG_MACDECODE flag is set on. Without this information the logging is
misleading as there is no reference to the VLAN header.
[12716.993704] test: IN=veth0 OUT= MACSRC=86:6c:92:ea:d6:73 MACDST=0e:3b:eb:86:73:76 VPROTO=8100 VID=10 MACPROTO=0800 SRC=192.168.10.2 DST=172.217.168.163 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=2548 DF PROTO=TCP SPT=55848 DPT=80 WINDOW=501 RES=0x00 ACK FIN URGP=0
[12721.157643] test: IN=veth0 OUT= MACSRC=86:6c:92:ea:d6:73 MACDST=0e:3b:eb:86:73:76 VPROTO=8100 VID=10 MACPROTO=0806 ARP HTYPE=1 PTYPE=0x0800 OPCODE=2 MACSRC=86:6c:92:ea:d6:73 IPSRC=192.168.10.2 MACDST=0e:3b:eb:86:73:76 IPDST=192.168.10.1
Fixes: 83e96d443b ("netfilter: log: split family specific code to nf_log_{ip,ip6,common}.c files")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02a1b175b0 ]
Documentation/networking/ip-sysctl.txt:46 says:
ip_forward_use_pmtu - BOOLEAN
By default we don't trust protocol path MTUs while forwarding
because they could be easily forged and can lead to unwanted
fragmentation by the router.
You only need to enable this if you have user-space software
which tries to discover path mtus by itself and depends on the
kernel honoring this information. This is normally not the case.
Default: 0 (disabled)
Possible values:
0 - disabled
1 - enabled
Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).
Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...
It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.
Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).
This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.
I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com>
Cc: Vinay Paradkar <vparadka@qti.qualcomm.com>
Cc: Tyler Wear <twear@quicinc.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 339ddaa626 upstream.
Starting with the upgrade to v5.8-rc3, I've noticed I wasn't able to
connect to my Bluetooth headset properly anymore. While connecting to
the device would eventually succeed, bluetoothd seemed to be confused
about the current connection state where the state was flapping hence
and forth. Bisecting this issue led to commit 3ca44c16b0 (Bluetooth:
Consolidate encryption handling in hci_encrypt_cfm, 2020-05-19), which
refactored `hci_encrypt_cfm` to also handle updating the connection
state.
The commit in question changed the code to call `hci_connect_cfm` inside
`hci_encrypt_cfm` and to change the connection state. But with the
conversion, we now only update the connection state if a status was set
already. In fact, the reverse should be true: the status should be
updated if no status is yet set. So let's fix the isuse by reversing the
condition.
Fixes: 3ca44c16b0 ("Bluetooth: Consolidate encryption handling in hci_encrypt_cfm")
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ca44c16b0 upstream.
This makes hci_encrypt_cfm calls hci_connect_cfm in case the connection
state is BT_CONFIG so callers don't have to check the state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Hans-Christian Noren Egtvedt <hegtvedt@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f19425641c upstream.
Only sockets will have the chan->data set to an actual sk, channels
like A2MP would have its own data which would likely cause a crash when
calling sk_filter, in order to fix this a new callback has been
introduced so channels can implement their own filtering if necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91a46c6d1b ]
XFRMA_REPLAY_ESN_VAL was not cloned completely from the old to the new.
Migrate this attribute during XFRMA_MSG_MIGRATE
v1->v2:
- move curleft cloning to a separate patch
Fixes: af2f464e32 ("xfrm: Assign esn pointers when cloning a state")
Signed-off-by: Antony Antony <antony.antony@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6735b4632d upstream.
syzbot has reported an issue in the framebuffer layer, where a malicious
user may overflow our built-in font data buffers.
In order to perform a reliable range check, subsystems need to know
`FONTDATAMAX` for each built-in font. Unfortunately, our font descriptor,
`struct console_font` does not contain `FONTDATAMAX`, and is part of the
UAPI, making it infeasible to modify it.
For user-provided fonts, the framebuffer layer resolves this issue by
reserving four extra words at the beginning of data buffers. Later,
whenever a function needs to access them, it simply uses the following
macros:
Recently we have gathered all the above macros to <linux/font.h>. Let us
do the same thing for built-in fonts, prepend four extra words (including
`FONTDATAMAX`) to their data buffers, so that subsystems can use these
macros for all fonts, no matter built-in or user-provided.
This patch depends on patch "fbdev, newport_con: Move FONT_EXTRA_WORDS
macros into linux/font.h".
Cc: stable@vger.kernel.org
Link: https://syzkaller.appspot.com/bug?id=08b8be45afea11888776f897895aef9ad1c3ecfd
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/ef18af00c35fb3cc826048a5f70924ed6ddce95b.1600953813.git.yepeilin.cs@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f85086f95f upstream.
In register_mem_sect_under_node() the system_state's value is checked to
detect whether the call is made during boot time or during an hot-plug
operation. Unfortunately, that check against SYSTEM_BOOTING is wrong
because regular memory is registered at SYSTEM_SCHEDULING state. In
addition, memory hot-plug operation can be triggered at this system
state by the ACPI [1]. So checking against the system state is not
enough.
The consequence is that on system with interleaved node's ranges like this:
Early memory node ranges
node 1: [mem 0x0000000000000000-0x000000011fffffff]
node 2: [mem 0x0000000120000000-0x000000014fffffff]
node 1: [mem 0x0000000150000000-0x00000001ffffffff]
node 0: [mem 0x0000000200000000-0x000000048fffffff]
node 2: [mem 0x0000000490000000-0x00000007ffffffff]
This can be seen on PowerPC LPAR after multiple memory hot-plug and
hot-unplug operations are done. At the next reboot the node's memory
ranges can be interleaved and since the call to link_mem_sections() is
made in topology_init() while the system is in the SYSTEM_SCHEDULING
state, the node's id is not checked, and the sections registered to
multiple nodes:
$ ls -l /sys/devices/system/memory/memory21/node*
total 0
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node1 -> ../../node/node1
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node2 -> ../../node/node2
In that case, the system is able to boot but if later one of theses
memory blocks is hot-unplugged and then hot-plugged, the sysfs
inconsistency is detected and this is triggering a BUG_ON():
kernel BUG at /Users/laurent/src/linux-ppc/mm/memory_hotplug.c:1084!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: rpadlpar_io rpaphp pseries_rng rng_core vmx_crypto gf128mul binfmt_misc ip_tables x_tables xfs libcrc32c crc32c_vpmsum autofs4
CPU: 8 PID: 10256 Comm: drmgr Not tainted 5.9.0-rc1+ #25
Call Trace:
add_memory_resource+0x23c/0x340 (unreliable)
__add_memory+0x5c/0xf0
dlpar_add_lmb+0x1b4/0x500
dlpar_memory+0x1f8/0xb80
handle_dlpar_errorlog+0xc0/0x190
dlpar_store+0x198/0x4a0
kobj_attr_store+0x30/0x50
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1b0/0x290
vfs_write+0xe8/0x290
ksys_write+0xdc/0x130
system_call_exception+0x160/0x270
system_call_common+0xf0/0x27c
This patch addresses the root cause by not relying on the system_state
value to detect whether the call is due to a hot-plug operation. An
extra parameter is added to link_mem_sections() detailing whether the
operation is due to a hot-plug operation.
[1] According to Oscar Salvador, using this qemu command line, ACPI
memory hotplug operations are raised at SYSTEM_SCHEDULING state:
$QEMU -enable-kvm -machine pc -smp 4,sockets=4,cores=1,threads=1 -cpu host -monitor pty \
-m size=$MEM,slots=255,maxmem=4294967296k \
-numa node,nodeid=0,cpus=0-3,mem=512 -numa node,nodeid=1,mem=512 \
-object memory-backend-ram,id=memdimm0,size=134217728 -device pc-dimm,node=0,memdev=memdimm0,id=dimm0,slot=0 \
-object memory-backend-ram,id=memdimm1,size=134217728 -device pc-dimm,node=0,memdev=memdimm1,id=dimm1,slot=1 \
-object memory-backend-ram,id=memdimm2,size=134217728 -device pc-dimm,node=0,memdev=memdimm2,id=dimm2,slot=2 \
-object memory-backend-ram,id=memdimm3,size=134217728 -device pc-dimm,node=0,memdev=memdimm3,id=dimm3,slot=3 \
-object memory-backend-ram,id=memdimm4,size=134217728 -device pc-dimm,node=1,memdev=memdimm4,id=dimm4,slot=4 \
-object memory-backend-ram,id=memdimm5,size=134217728 -device pc-dimm,node=1,memdev=memdimm5,id=dimm5,slot=5 \
-object memory-backend-ram,id=memdimm6,size=134217728 -device pc-dimm,node=1,memdev=memdimm6,id=dimm6,slot=6 \
Fixes: 4fbce63391 ("mm/memory_hotplug.c: make register_mem_sect_under_node() a callback of walk_memory_range()")
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200915094143.79181-3-ldufour@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1d0da8335 upstream.
Patch series "mm: fix memory to node bad links in sysfs", v3.
Sometimes, firmware may expose interleaved memory layout like this:
Early memory node ranges
node 1: [mem 0x0000000000000000-0x000000011fffffff]
node 2: [mem 0x0000000120000000-0x000000014fffffff]
node 1: [mem 0x0000000150000000-0x00000001ffffffff]
node 0: [mem 0x0000000200000000-0x000000048fffffff]
node 2: [mem 0x0000000490000000-0x00000007ffffffff]
In that case, we can see memory blocks assigned to multiple nodes in
sysfs:
$ ls -l /sys/devices/system/memory/memory21
total 0
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node1 -> ../../node/node1
lrwxrwxrwx 1 root root 0 Aug 24 05:27 node2 -> ../../node/node2
-rw-r--r-- 1 root root 65536 Aug 24 05:27 online
-r--r--r-- 1 root root 65536 Aug 24 05:27 phys_device
-r--r--r-- 1 root root 65536 Aug 24 05:27 phys_index
drwxr-xr-x 2 root root 0 Aug 24 05:27 power
-r--r--r-- 1 root root 65536 Aug 24 05:27 removable
-rw-r--r-- 1 root root 65536 Aug 24 05:27 state
lrwxrwxrwx 1 root root 0 Aug 24 05:25 subsystem -> ../../../../bus/memory
-rw-r--r-- 1 root root 65536 Aug 24 05:25 uevent
-r--r--r-- 1 root root 65536 Aug 24 05:27 valid_zones
The same applies in the node's directory with a memory21 link in both
the node1 and node2's directory.
This is wrong but doesn't prevent the system to run. However when
later, one of these memory blocks is hot-unplugged and then hot-plugged,
the system is detecting an inconsistency in the sysfs layout and a
BUG_ON() is raised:
kernel BUG at /Users/laurent/src/linux-ppc/mm/memory_hotplug.c:1084!
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: rpadlpar_io rpaphp pseries_rng rng_core vmx_crypto gf128mul binfmt_misc ip_tables x_tables xfs libcrc32c crc32c_vpmsum autofs4
CPU: 8 PID: 10256 Comm: drmgr Not tainted 5.9.0-rc1+ #25
Call Trace:
add_memory_resource+0x23c/0x340 (unreliable)
__add_memory+0x5c/0xf0
dlpar_add_lmb+0x1b4/0x500
dlpar_memory+0x1f8/0xb80
handle_dlpar_errorlog+0xc0/0x190
dlpar_store+0x198/0x4a0
kobj_attr_store+0x30/0x50
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1b0/0x290
vfs_write+0xe8/0x290
ksys_write+0xdc/0x130
system_call_exception+0x160/0x270
system_call_common+0xf0/0x27c
This has been seen on PowerPC LPAR.
The root cause of this issue is that when node's memory is registered,
the range used can overlap another node's range, thus the memory block
is registered to multiple nodes in sysfs.
There are two issues here:
(a) The sysfs memory and node's layouts are broken due to these
multiple links
(b) The link errors in link_mem_sections() should not lead to a system
panic.
To address (a) register_mem_sect_under_node should not rely on the
system state to detect whether the link operation is triggered by a hot
plug operation or not. This is addressed by the patches 1 and 2 of this
series.
Issue (b) will be addressed separately.
This patch (of 2):
The memmap_context enum is used to detect whether a memory operation is
due to a hot-add operation or happening at boot time.
Make it general to the hotplug operation and rename it as
meminit_context.
There is no functional change introduced by this patch
Suggested-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J . Wysocki" <rafael@kernel.org>
Cc: Nathan Lynch <nathanl@linux.ibm.com>
Cc: Scott Cheloha <cheloha@linux.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20200915094143.79181-1-ldufour@linux.ibm.com
Link: https://lkml.kernel.org/r/20200915132624.9723-1-ldufour@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4c7246dc45 ]
We are going to add 'struct vsock_sock *' parameter to
virtio_transport_get_ops().
In some cases, like in the virtio_transport_reset_no_sock(),
we don't have any socket assigned to the packet received,
so we can't use the virtio_transport_get_ops().
In order to allow virtio_transport_reset_no_sock() to use the
'.send_pkt' callback from the 'vhost_transport' or 'virtio_transport',
we add the 'struct virtio_transport *' to it and to its caller:
virtio_transport_recv_pkt().
We moved the 'vhost_transport' and 'virtio_transport' definition,
to pass their address to the virtio_transport_recv_pkt().
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 95364f3670 upstream.
In case a driver wants to return an error from qc_prep, return enum
ata_completion_errors. sata_mv is one of those drivers -- see the next
patch. Other drivers return the newly defined AC_ERR_OK.
[v2] use enum ata_completion_errors and AC_ERR_OK.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08ca8b21f7 ]
When a subrequest is being detached from the subgroup, we want to
ensure that it is not holding the group lock, or in the process
of waiting for the group lock.
Fixes: 5b2b5187fa ("NFS: Fix nfs_page_group_destroy() and nfs_lock_and_join_requests() race cases")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72e0ef0e5f ]
On some EFI systems, the video BIOS is provided by the EFI firmware. The
boot stub code stores the physical address of the ROM image in pdev->rom.
Currently we attempt to access this pointer using phys_to_virt(), which
doesn't work with CONFIG_HIGHMEM.
On these systems, attempting to load the radeon module on a x86_32 kernel
can result in the following:
BUG: unable to handle page fault for address: 3e8ed03c
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
*pde = 00000000
Oops: 0000 [#1] PREEMPT SMP
CPU: 0 PID: 317 Comm: systemd-udevd Not tainted 5.6.0-rc3-next-20200228 #2
Hardware name: Apple Computer, Inc. MacPro1,1/Mac-F4208DC8, BIOS MP11.88Z.005C.B08.0707021221 07/02/07
EIP: radeon_get_bios+0x5ed/0xe50 [radeon]
Code: 00 00 84 c0 0f 85 12 fd ff ff c7 87 64 01 00 00 00 00 00 00 8b 47 08 8b 55 b0 e8 1e 83 e1 d6 85 c0 74 1a 8b 55 c0 85 d2 74 13 <80> 38 55 75 0e 80 78 01 aa 0f 84 a4 03 00 00 8d 74 26 00 68 dc 06
EAX: 3e8ed03c EBX: 00000000 ECX: 3e8ed03c EDX: 00010000
ESI: 00040000 EDI: eec04000 EBP: eef3fc60 ESP: eef3fbe0
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010206
CR0: 80050033 CR2: 3e8ed03c CR3: 2ec77000 CR4: 000006d0
Call Trace:
r520_init+0x26/0x240 [radeon]
radeon_device_init+0x533/0xa50 [radeon]
radeon_driver_load_kms+0x80/0x220 [radeon]
drm_dev_register+0xa7/0x180 [drm]
radeon_pci_probe+0x10f/0x1a0 [radeon]
pci_device_probe+0xd4/0x140
Fix the issue by updating all drivers which can access a platform provided
ROM. Instead of calling the helper function pci_platform_rom() which uses
phys_to_virt(), call ioremap() directly on the pdev->rom.
radeon_read_platform_bios() previously directly accessed an __iomem
pointer. Avoid this by calling memcpy_fromio() instead of kmemdup().
pci_platform_rom() now has no remaining callers, so remove it.
Link: https://lore.kernel.org/r/20200319021623.5426-1-mikel@mikelr.com
Signed-off-by: Mikel Rychliski <mikel@mikelr.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86b18aaa2b ]
sk_buff.qlen can be accessed concurrently as noticed by KCSAN,
BUG: KCSAN: data-race in __skb_try_recv_from_queue / unix_dgram_sendmsg
read to 0xffff8a1b1d8a81c0 of 4 bytes by task 5371 on cpu 96:
unix_dgram_sendmsg+0x9a9/0xb70 include/linux/skbuff.h:1821
net/unix/af_unix.c:1761
____sys_sendmsg+0x33e/0x370
___sys_sendmsg+0xa6/0xf0
__sys_sendmsg+0x69/0xf0
__x64_sys_sendmsg+0x51/0x70
do_syscall_64+0x91/0xb47
entry_SYSCALL_64_after_hwframe+0x49/0xbe
write to 0xffff8a1b1d8a81c0 of 4 bytes by task 1 on cpu 99:
__skb_try_recv_from_queue+0x327/0x410 include/linux/skbuff.h:2029
__skb_try_recv_datagram+0xbe/0x220
unix_dgram_recvmsg+0xee/0x850
____sys_recvmsg+0x1fb/0x210
___sys_recvmsg+0xa2/0xf0
__sys_recvmsg+0x66/0xf0
__x64_sys_recvmsg+0x51/0x70
do_syscall_64+0x91/0xb47
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Since only the read is operating as lockless, it could introduce a logic
bug in unix_recvq_full() due to the load tearing. Fix it by adding
a lockless variant of skb_queue_len() and unix_recvq_full() where
READ_ONCE() is on the read while WRITE_ONCE() is on the write similar to
the commit d7d16a8935 ("net: add skb_queue_empty_lockless()").
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f643ee295c ]
The original patch bringed in the "SCTP ACK tracking trace event"
feature was committed at Dec.20, 2017, it replaced jprobe usage
with trace events, and bringed in two trace events, one is
TRACE_EVENT(sctp_probe), another one is TRACE_EVENT(sctp_probe_path).
The original patch intended to trigger the trace_sctp_probe_path in
TRACE_EVENT(sctp_probe) as below code,
+TRACE_EVENT(sctp_probe,
+
+ TP_PROTO(const struct sctp_endpoint *ep,
+ const struct sctp_association *asoc,
+ struct sctp_chunk *chunk),
+
+ TP_ARGS(ep, asoc, chunk),
+
+ TP_STRUCT__entry(
+ __field(__u64, asoc)
+ __field(__u32, mark)
+ __field(__u16, bind_port)
+ __field(__u16, peer_port)
+ __field(__u32, pathmtu)
+ __field(__u32, rwnd)
+ __field(__u16, unack_data)
+ ),
+
+ TP_fast_assign(
+ struct sk_buff *skb = chunk->skb;
+
+ __entry->asoc = (unsigned long)asoc;
+ __entry->mark = skb->mark;
+ __entry->bind_port = ep->base.bind_addr.port;
+ __entry->peer_port = asoc->peer.port;
+ __entry->pathmtu = asoc->pathmtu;
+ __entry->rwnd = asoc->peer.rwnd;
+ __entry->unack_data = asoc->unack_data;
+
+ if (trace_sctp_probe_path_enabled()) {
+ struct sctp_transport *sp;
+
+ list_for_each_entry(sp, &asoc->peer.transport_addr_list,
+ transports) {
+ trace_sctp_probe_path(sp, asoc);
+ }
+ }
+ ),
But I found it did not work when I did testing, and trace_sctp_probe_path
had no output, I finally found that there is trace buffer lock
operation(trace_event_buffer_reserve) in include/trace/trace_events.h:
static notrace void \
trace_event_raw_event_##call(void *__data, proto) \
{ \
struct trace_event_file *trace_file = __data; \
struct trace_event_data_offsets_##call __maybe_unused __data_offsets;\
struct trace_event_buffer fbuffer; \
struct trace_event_raw_##call *entry; \
int __data_size; \
\
if (trace_trigger_soft_disabled(trace_file)) \
return; \
\
__data_size = trace_event_get_offsets_##call(&__data_offsets, args); \
\
entry = trace_event_buffer_reserve(&fbuffer, trace_file, \
sizeof(*entry) + __data_size); \
\
if (!entry) \
return; \
\
tstruct \
\
{ assign; } \
\
trace_event_buffer_commit(&fbuffer); \
}
The reason caused no output of trace_sctp_probe_path is that
trace_sctp_probe_path written in TP_fast_assign part of
TRACE_EVENT(sctp_probe), and it will be placed( { assign; } ) after the
trace_event_buffer_reserve() when compiler expands Macro,
entry = trace_event_buffer_reserve(&fbuffer, trace_file, \
sizeof(*entry) + __data_size); \
\
if (!entry) \
return; \
\
tstruct \
\
{ assign; } \
so trace_sctp_probe_path finally can not acquire trace_event_buffer
and return no output, that is to say the nest of tracepoint entry function
is not allowed. The function call flow is:
trace_sctp_probe()
-> trace_event_raw_event_sctp_probe()
-> lock buffer
-> trace_sctp_probe_path()
-> trace_event_raw_event_sctp_probe_path() --nested
-> buffer has been locked and return no output.
This patch is to remove trace_sctp_probe_path from the TP_fast_assign
part of TRACE_EVENT(sctp_probe) to avoid the nest of entry function,
and trigger sctp_probe_path_trace in sctp_outq_sack.
After this patch, you can enable both events individually,
# cd /sys/kernel/debug/tracing
# echo 1 > events/sctp/sctp_probe/enable
# echo 1 > events/sctp/sctp_probe_path/enable
Or, you can enable all the events under sctp.
# echo 1 > events/sctp/enable
Signed-off-by: Kevin Kou <qdkevin.kou@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf07132f96 ]
This patch proposes to require marked atomic accesses surrounding
raw_write_seqcount_barrier. We reason that otherwise there is no way to
guarantee propagation nor atomicity of writes before/after the barrier
[1]. For example, consider the compiler tears stores either before or
after the barrier; in this case, readers may observe a partial value,
and because readers are unaware that writes are going on (writes are not
in a seq-writer critical section), will complete the seq-reader critical
section while having observed some partial state.
[1] https://lwn.net/Articles/793253/
This came up when designing and implementing KCSAN, because KCSAN would
flag these accesses as data-races. After careful analysis, our reasoning
as above led us to conclude that the best thing to do is to propose an
amendment to the raw_seqcount_barrier usage.
Signed-off-by: Marco Elver <elver@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3d7c2292d ]
With large eMMC cards, it is possible to create general purpose
partitions that are bigger than 4GB. The size member of the mmc_part
struct is only an unsigned int which overflows for gp partitions larger
than 4GB. Change this to a u64 to handle the overflow.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 78dc70ebaa upstream.
Aggregation effects are extremely common with wifi, cellular, and cable
modem link technologies, ACK decimation in middleboxes, and LRO and GRO
in receiving hosts. The aggregation can happen in either direction,
data or ACKs, but in either case the aggregation effect is visible
to the sender in the ACK stream.
Previously BBR's sending was often limited by cwnd under severe ACK
aggregation/decimation because BBR sized the cwnd at 2*BDP. If packets
were acked in bursts after long delays (e.g. one ACK acking 5*BDP after
5*RTT), BBR's sending was halted after sending 2*BDP over 2*RTT, leaving
the bottleneck idle for potentially long periods. Note that loss-based
congestion control does not have this issue because when facing
aggregation it continues increasing cwnd after bursts of ACKs, growing
cwnd until the buffer is full.
To achieve good throughput in the presence of aggregation effects, this
algorithm allows the BBR sender to put extra data in flight to keep the
bottleneck utilized during silences in the ACK stream that it has evidence
to suggest were caused by aggregation.
A summary of the algorithm: when a burst of packets are acked by a
stretched ACK or a burst of ACKs or both, BBR first estimates the expected
amount of data that should have been acked, based on its estimated
bandwidth. Then the surplus ("extra_acked") is recorded in a windowed-max
filter to estimate the recent level of observed ACK aggregation. Then cwnd
is increased by the ACK aggregation estimate. The larger cwnd avoids BBR
being cwnd-limited in the face of ACK silences that recent history suggests
were caused by aggregation. As a sanity check, the ACK aggregation degree
is upper-bounded by the cwnd (at the time of measurement) and a global max
of BW * 100ms. The algorithm is further described by the following
presentation:
https://datatracker.ietf.org/meeting/101/materials/slides-101-iccrg-an-update-on-bbr-work-at-google-00
In our internal testing, we observed a significant increase in BBR
throughput (measured using netperf), in a basic wifi setup.
- Host1 (sender on ethernet) -> AP -> Host2 (receiver on wifi)
- 2.4 GHz -> BBR before: ~73 Mbps; BBR after: ~102 Mbps; CUBIC: ~100 Mbps
- 5.0 GHz -> BBR before: ~362 Mbps; BBR after: ~593 Mbps; CUBIC: ~601 Mbps
Also, this code is running globally on YouTube TCP connections and produced
significant bandwidth increases for YouTube traffic.
This is based on Ian Swett's max_ack_height_ algorithm from the
QUIC BBR implementation.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15e9e35cd1 ]
MIPS defines two kvm types:
#define KVM_VM_MIPS_TE 0
#define KVM_VM_MIPS_VZ 1
In Documentation/virt/kvm/api.rst it is said that "You probably want to
use 0 as machine type", which implies that type 0 be the "automatic" or
"default" type. And, in user-space libvirt use the null-machine (with
type 0) to detect the kvm capability, which returns "KVM not supported"
on a VZ platform.
I try to fix it in QEMU but it is ugly:
https://lists.nongnu.org/archive/html/qemu-devel/2020-08/msg05629.html
And Thomas Huth suggests me to change the definition of kvm type:
https://lists.nongnu.org/archive/html/qemu-devel/2020-09/msg03281.html
So I define like this:
#define KVM_VM_MIPS_AUTO 0
#define KVM_VM_MIPS_VZ 1
#define KVM_VM_MIPS_TE 2
Since VZ and TE cannot co-exists, using type 0 on a TE platform will
still return success (so old user-space tools have no problems on new
kernels); the advantage is that using type 0 on a VZ platform will not
return failure. So, the only problem is "new user-space tools use type
2 on old kernels", but if we treat this as a kernel bug, we can backport
this patch to old stable kernels.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Message-Id: <1599734031-28746-1-git-send-email-chenhc@lemote.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a355aeb24 ]
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89d29997f1 ]
eznps driver is supposed to be platform independent however it ends up
including stuff from inside arch/arc headers leading to rand config
build errors.
The quick hack to fix this (proper fix is too much chrun for non active
user-base) is to add following to nps platform agnostic header.
- copy AUX_IENABLE from arch/arc header
- move CTOP_AUX_IACK from arch/arc/plat-eznps/*/**
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/20200824095831.5lpkmkafelnvlpi2@linutronix.de
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc5453a5b7 ]
If an sctp connection gets re-used, heartbeats are flagged as invalid
because their vtag doesn't match.
Handle this in a similar way as TCP conntrack when it suspects that the
endpoints and conntrack are out-of-sync.
When a HEARTBEAT request fails its vtag validation, flag this in the
conntrack state and accept the packet.
When a HEARTBEAT_ACK is received with an invalid vtag in the reverse
direction after we allowed such a HEARTBEAT through, assume we are
out-of-sync and re-set the vtag info.
v2: remove left-over snippet from an older incarnation that moved
new_state/old_state assignments, thats not needed so keep that
as-is.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3b5455636f upstream.
All three generations of Sandisk SSDs lock up hard intermittently.
Experiments showed that disabling NCQ lowered the failure rate significantly
and the kernel has been disabling NCQ for some models of SD7's and 8's,
which is obviously undesirable.
Karthik worked with Sandisk to root cause the hard lockups to trim commands
larger than 128M. This patch implements ATA_HORKAGE_MAX_TRIM_128M which
limits max trim size to 128M and applies it to all three generations of
Sandisk SSDs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Karthik Shivaram <karthikgs@fb.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d1585ca0f ]
Commit 3d7081822f ("uaccess: Add non-pagefault user-space read functions")
missed to add probe write function, therefore factor out a probe_write_common()
helper with most logic of probe_kernel_write() except setting KERNEL_DS, and
add a new probe_user_write() helper so it can be used from BPF side.
Again, on some archs, the user address space and kernel address space can
co-exist and be overlapping, so in such case, setting KERNEL_DS would mean
that the given address is treated as being in kernel address space.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/bpf/9df2542e68141bfa3addde631441ee45503856a8.1572649915.git.daniel@iogearbox.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d7081822f ]
Add probe_user_read(), strncpy_from_unsafe_user() and
strnlen_unsafe_user() which allows caller to access user-space
in IRQ context.
Current probe_kernel_read() and strncpy_from_unsafe() are
not available for user-space memory, because it sets
KERNEL_DS while accessing data. On some arch, user address
space and kernel address space can be co-exist, but others
can not. In that case, setting KERNEL_DS means given
address is treated as a kernel address space.
Also strnlen_user() is only available from user context since
it can sleep if pagefault is enabled.
To access user-space memory without pagefault, we need
these new functions which sets USER_DS while accessing
the data.
Link: http://lkml.kernel.org/r/155789869802.26965.4940338412595759063.stgit@devnote2
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee92118355 ]
Frontend callback reports EAGAIN to nfnetlink to retry a command, this
is used to signal that module autoloading is required. Unfortunately,
nlmsg_unicast() reports EAGAIN in case the receiver socket buffer gets
full, so it enters a busy-loop.
This patch updates nfnetlink_unicast() to turn EAGAIN into ENOBUFS and
to use nlmsg_unicast(). Remove the flags field in nfnetlink_unicast()
since this is always MSG_DONTWAIT in the existing code which is exactly
what nlmsg_unicast() passes to netlink_unicast() as parameter.
Fixes: 96518518cc ("netfilter: add nftables")
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e105e6afa ]
Following bug was reported via irc:
nft list ruleset
set knock_candidates_ipv4 {
type ipv4_addr . inet_service
size 65535
elements = { 127.0.0.1 . 123,
127.0.0.1 . 123 }
}
..
udp dport 123 add @knock_candidates_ipv4 { ip saddr . 123 }
udp dport 123 add @knock_candidates_ipv4 { ip saddr . udp dport }
It should not have been possible to add a duplicate set entry.
After some debugging it turned out that the problem is the immediate
value (123) in the second-to-last rule.
Concatenations use 32bit registers, i.e. the elements are 8 bytes each,
not 6 and it turns out the kernel inserted
inet firewall @knock_candidates_ipv4
element 0100007f ffff7b00 : 0 [end]
element 0100007f 00007b00 : 0 [end]
Note the non-zero upper bits of the first element. It turns out that
nft_immediate doesn't zero the destination register, but this is needed
when the length isn't a multiple of 4.
Furthermore, the zeroing in nft_payload is broken. We can't use
[len / 4] = 0 -- if len is a multiple of 4, index is off by one.
Skip zeroing in this case and use a conditional instead of (len -1) / 4.
Fixes: 49499c3e6e ("netfilter: nf_tables: switch registers to 32 bit addressing")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da9125df85 ]
This should be NFTA_LIST_UNSPEC instead of NFTA_LIST_UNPEC, all other
similar attribute definitions are postfixed with _UNSPEC.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
