It is very common for regulators to support having their enable signal
controlled by a GPIO. Since there are a bunch of fiddly things to get
right like handling the operations when the enable signal is tied to
a rail and it's just replicated code add support for this to the core.
Drivers should set ena_gpio in their config if they have a GPIO control,
using ena_gpio_flags to specify any flags (including GPIOF_OUT_INIT_ for
the initial state) and ena_gpio_invert if the GPIO is active low. The
core will then override any enable and disable operations the driver has
and instead control the specified GPIO.
This will in the future also allow us to further extend the core by
identifying when several enable signals have been tied together and
handling this properly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many regulators have a fixed specification for their enable time. Allow
this to be set in the regulator_desc as a number to save them having to
implement an explicit operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to avoid compilation failure when KVM is not compiled in,
guard the mmu_notifier specific sections with both CONFIG_MMU_NOTIFIER
and KVM_ARCH_WANT_MMU_NOTIFIER, like it is being done in the rest of
the KVM code.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
On some systems there are CPU cores located in the same power
domains as I/O devices. Then, power can only be removed from the
domain if all I/O devices in it are not in use and the CPU core
is idle. Add preliminary support for that to the generic PM domains
framework.
First, the platform is expected to provide a cpuidle driver with one
extra state designated for use with the generic PM domains code.
This state should be initially disabled and its exit_latency value
should be set to whatever time is needed to bring up the CPU core
itself after restoring power to it, not including the domain's
power on latency. Its .enter() callback should point to a procedure
that will remove power from the domain containing the CPU core at
the end of the CPU power transition.
The remaining characteristics of the extra cpuidle state, referred to
as the "domain" cpuidle state below, (e.g. power usage, target
residency) should be populated in accordance with the properties of
the hardware.
Next, the platform should execute genpd_attach_cpuidle() on the PM
domain containing the CPU core. That will cause the generic PM
domains framework to treat that domain in a special way such that:
* When all devices in the domain have been suspended and it is about
to be turned off, the states of the devices will be saved, but
power will not be removed from the domain. Instead, the "domain"
cpuidle state will be enabled so that power can be removed from
the domain when the CPU core is idle and the state has been chosen
as the target by the cpuidle governor.
* When the first I/O device in the domain is resumed and
__pm_genpd_poweron(() is called for the first time after
power has been removed from the domain, the "domain" cpuidle
state will be disabled to avoid subsequent surprise power removals
via cpuidle.
The effective exit_latency value of the "domain" cpuidle state
depends on the time needed to bring up the CPU core itself after
restoring power to it as well as on the power on latency of the
domain containing the CPU core. Thus the "domain" cpuidle state's
exit_latency has to be recomputed every time the domain's power on
latency is updated, which may happen every time power is restored
to the domain, if the measured power on latency is greater than
the latency stored in the corresponding generic_pm_domain structure.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Andrew J.Schorr raises a question. When he changes the disable setting on
a single CPU, it affects all the other CPUs. Basically, currently, the
disable field is per-driver instead of per-cpu. All the C states of the
same driver are shared by all CPU in the same machine.
The patch changes the `disable' field to per-cpu, so we could set this
separately for each cpu.
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Reported-by: Andrew J.Schorr <aschorr@telemetry-investments.com>
Reviewed-by: Yanmin Zhang <yanmin_zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some drivers require setup before being able to send
management frames in managed mode, in particular in
multi-channel cases.
Introduce API to allow the drivers to do such setup
while being able to sleep waiting for the setup to
finish in the device. This isn't possible inside the
TX call since that can't sleep.
A future patch may also restructure the TX retry to
wait for the driver to report the frame status, as
suggested by Arik in
http://mid.gmane.org/CA+XVXffKSEL6ZQPQ98x-zO-NL2=TNF1uN==mprRyUmAaRn254g@mail.gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE80211_TX_MAX_RATES can be reduced from 5 to 4 as there
is no current hardware supporting a rate chain with 5 multi
rate stages (mrr), so 4 mrr stages are sufficient.
The memory that is freed within the ieee80211_tx_info struct
will be used in the upcoming Transmission Power Control (TPC)
implementation.
Suggested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a bit clean up of public sound header directory.
Some header files in include/sound aren't really necessary to be
located there but can be moved to their local directories gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Straightforward conversion to the new pm_ops from the legacy
suspend/resume ops.
Since we change vx222, vx_core and vxpocket have to be converted,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Prune this down to just the struct kvm_irqfd so we can avoid
changing function definition for every flag or field we use.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Commit d8169d4c (Make __kfree_rcu() less dependent on compiler choices)
created a macro out of an inline function in order to avoid build
breakage for certain combinations of gcc flags. Unfortunately, it also
converted a kfree_call_rcu() to a call_rcu(), which made the rcu_data
structure's ->qlen_lazy field lose counts. This commit therefore changes
the call_rcu() back to kfree_call_rcu().
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Although __call_rcu() is handled correctly when called from a momentary
non-idle period, if it is called on a CPU that RCU believes to be idle
on RCU_FAST_NO_HZ kernels, the callback might be indefinitely postponed.
This commit therefore ensures that RCU is aware of the new callback and
has a chance to force the CPU out of dyntick-idle mode when a new callback
is posted.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Commit d8169d4c (Make __kfree_rcu() less dependent on compiler choices)
added cpp macro versions of __kfree_rcu() and __is_kfree_rcu_offset(),
but failed to remove the old inline-function versions. This commit does
this cleanup.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The CONFIG_TREE_PREEMPT_RCU and CONFIG_TINY_PREEMPT_RCU versions of
__rcu_read_lock() and __rcu_read_unlock() are identical, so this commit
consolidates them into kernel/rcupdate.h.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The return value from rcu_assign_pointer() is not used, and using it
would be quite ugly, for example:
q = rcu_assign_pointer(global_p, p);
To prevent this sort of ugliness from spreading, this commit wraps
rcu_assign_pointer() in a do-while loop.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reported-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit removes the extraneous parentheses from rcu_assign_keypointer()
so that rcu_assign_pointer() can be wrapped in do-while. It also wraps
rcu_assign_keypointer() in a do-while and parenthesizes its final argument,
as suggested by David Howells.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The return value from RCU_INIT_POINTER() is not used, and using it
would be quite ugly, for example:
q = RCU_INIT_POINTER(global_p, p);
To prevent this sort of ugliness from appearing, this commit wraps
RCU_INIT_POINTER() in a do-while loop.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: David Howells <dhowells@redhat.com>
This commit applies the INIT_RCU_POINTER() macro to all uses of
RCU_POINTER_INITIALIZER() that were all too cleverly creating gcc-style
initializations.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
RCU_INIT_POINTER() returns a value that is never used, and which should
be abolished due to terminal ugliness:
q = RCU_INIT_POINTER(global_p, p);
However, there are two uses that cannot be handled by a do-while
formulation because they do gcc-style initialization:
RCU_INIT_POINTER(.real_cred, &init_cred),
RCU_INIT_POINTER(.cred, &init_cred),
This usage is clever, but not necessarily the nicest approach.
This commit therefore creates an RCU_POINTER_INITIALIZER() macro that
is specifically designed for gcc-style initialization.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
This reverts commit 616c310e83.
(Move PREEMPT_RCU preemption to switch_to() invocation).
Testing by Sasha Levin <levinsasha928@gmail.com> showed that this
can result in deadlock due to invoking the scheduler when one of
the runqueue locks is held. Because this commit was simply a
performance optimization, revert it.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
The implementation of tx_frags is buggy due to
not handling queue stop, and there's no driver
implementing it so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide various constants as defined by the 802.11ad:
frame types, IE's, capability bits, action categories
Introduce GCMP cipher, mandatory by 802.11ad
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add enumerations for both cfg80211 and nl80211.
This expands wiphy.bands etc. arrays.
Extend channel <-> frequency translation to cover 60g band
and modify the rate check logic since there are no legacy
mandatory rates (only MCS is used.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the unused fields from struct ssp_config_chip that was removed
before
Add bus_id documentation to pl022_ssp_controller
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
Register OMAP DRM/KMS platform device. DMM is split into a
separate device using hwmod.
Signed-off-by: Andy Gross <andy.gross@ti.com>
Signed-off-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A consistent name with slub saves us an acessor function.
In both caches, this field represents the same thing. We would
like to use it from the mem_cgroup code.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Acked-by: Christoph Lameter <cl@linux.com>
CC: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Convert tps65217_pmic_ldo1_ops to use regulator_list_voltage_table.
We have n_voltages and volt_table settings in regulator_desc,
so we don't need the table and table_len fields in struct tps_info.
Thus remove them from struct tps_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This definition is missing when CONFIG_REGULATOR is not defined.
This causes compiler errors when compiling sdhci.c. This can
be worked around by adding #ifdef CONFIG_REGULATOR .. #endif
but since other definitions are there we have defined the missing
definition
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get rid of the unnecessary checks in dma_slave_config utilizing
the DMA direction. This allows us to move the computation of
cctl to the prepare function.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Try to avoid dereferencing the DMA engine's channel struct in these
platform helpers; instead, pass a pointer to the channel data into
get_signal(), and the returned signal number to put_signal().
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Circular buffers are not handled in this way; we have a separate API
call now to setup circular buffers. So lets not mislead people with
this bool.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the behavior of the newly introduced
/sys/power/pm_print_times attribute so that its initial value
depends on initcall_debug, but setting it to 0 will cause device
suspend/resume times not to be printed, even if initcall_debug has
been set. This way, the people who use initcall_debug for reasons
other than PM debugging will be able to switch the suspend/resume
times printing off, if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the legacy ACPI driver PM callbacks included into
struct acpi_device_ops are not used any more, drop them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Make the ACPI processor driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct acpi_device_ops.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
None of the drivers implementing the ACPI device suspend callback
uses the pm_message_t argument of it, so this argument may be dropped
entirely from that callback. This will simplify switching the ACPI
bus type to PM handling based on struct dev_pm_ops.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).
An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.
In the end, this patch also adds the EEE ethtool support implementing:
o phy_ethtool_set_eee
o phy_ethtool_get_eee
v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
values according to ethtool API (thanks to Ben's feedback).
Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
Fixed the phy_init_eee function: we need to check which link mode
was autonegotiated and then the corresponding bits in 7.60 and 7.61
registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was noticed recently that when we send data on a transport, its possible that
we might bundle a sack that arrived on a different transport. While this isn't
a major problem, it does go against the SHOULD requirement in section 6.4 of RFC
2960:
An endpoint SHOULD transmit reply chunks (e.g., SACK, HEARTBEAT ACK,
etc.) to the same destination transport address from which it
received the DATA or control chunk to which it is replying. This
rule should also be followed if the endpoint is bundling DATA chunks
together with the reply chunk.
This patch seeks to correct that. It restricts the bundling of sack operations
to only those transports which have moved the ctsn of the association forward
since the last sack. By doing this we guarantee that we only bundle outbound
saks on a transport that has received a chunk since the last sack. This brings
us into stricter compliance with the RFC.
Vlad had initially suggested that we strictly allow only sack bundling on the
transport that last moved the ctsn forward. While this makes sense, I was
concerned that doing so prevented us from bundling in the case where we had
received chunks that moved the ctsn on multiple transports. In those cases, the
RFC allows us to select any of the transports having received chunks to bundle
the sack on. so I've modified the approach to allow for that, by adding a state
variable to each transport that tracks weather it has moved the ctsn since the
last sack. This I think keeps our behavior (and performance), close enough to
our current profile that I think we can do this without a sysctl knob to
enable/disable it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yaseivch <vyasevich@gmail.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
Reported-by: Michele Baldessari <michele@redhat.com>
Reported-by: sorin serban <sserban@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning. This struct member was removed in commit
875682648b ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.
Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve debugging of hci_conn objects by: adding print to hci_conn
refcounting, adding object spcifier when missing, change conn to hcon
since conn is heavily used for l2cap_conn objects and this is misleading.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
There will probably be a number of such modifiers eventually but
this one is used in the adis16240 accelerometer driver.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There will probably be a number of such modifiers eventually but
this one is used in the adis16204 accelerometer driver.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These were originally introduced when the plan was to have parallel
IIO cores in and out of staging with a slow move between them.
Now we have reached the point where the whole core has moved,
they need clearing up!
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the Analog Devices AD7265 and AD7266
Analog-to-Digital converters.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
