[ Upstream commit ac5b70198a ]
netif_set_real_num_tx_queues() can be called when netdev is up.
That usually happens when user requests change of number of
channels/rings with ethtool -L. The procedure for changing
the number of queues involves resetting the qdiscs and setting
dev->num_tx_queues to the new value. When the new value is
lower than the old one, extra care has to be taken to ensure
ordering of accesses to the number of queues vs qdisc reset.
Currently the queues are reset before new dev->num_tx_queues
is assigned, leaving a window of time where packets can be
enqueued onto the queues going down, leading to a likely
crash in the drivers, since most drivers don't check if TX
skbs are assigned to an active queue.
Fixes: e6484930d7 ("net: allocate tx queues in register_netdevice")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d74e9f88d upstream.
skb_warn_bad_offload warns when packets enter the GSO stack that
require skb_checksum_help or vice versa. Do not warn on arbitrary
bad packets. Packet sockets can craft many. Syzkaller was able to
demonstrate another one with eth_type games.
In particular, suppress the warning when segmentation returns an
error, which is for reasons other than checksum offload.
See also commit 36c9247449 ("net: WARN if skb_checksum_help() is
called on skb requiring segmentation") for context on this warning.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7c68d1a6b4 ]
Without proper validation of DODGY packets, we might very well
feed qdisc_pkt_len_init() with invalid GSO packets.
tcp_hdrlen() might access out-of-bound data, so let's use
skb_header_pointer() and proper checks.
Whole story is described in commit d0c081b491 ("flow_dissector:
properly cap thoff field")
We have the goal of validating DODGY packets earlier in the stack,
so we might very well revert this fix in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Reported-by: syzbot+9da69ebac7dddd804552@syzkaller.appspotmail.com
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 37c343b4f4 ]
When we notify peers of potential changes, it's also good to update
IGMP memberships. For example, during VM migration, updating IGMP
memberships will redirect existing multicast streams to the VM at the
new location.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ad646c81b ]
register_netdevice() could fail early when we have an invalid
dev name, in which case ->ndo_uninit() is not called. For tun
device, this is a problem because a timer etc. are already
initialized and it expects ->ndo_uninit() to clean them up.
We could move these initializations into a ->ndo_init() so
that register_netdevice() knows better, however this is still
complicated due to the logic in tun_detach().
Therefore, I choose to just call dev_get_valid_name() before
register_netdevice(), which is quicker and much easier to audit.
And for this specific case, it is already enough.
Fixes: 96442e4242 ("tuntap: choose the txq based on rxq")
Reported-by: Dmitry Alexeev <avekceeb@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8d63bee643 ]
skb_warn_bad_offload triggers a warning when an skb enters the GSO
stack at __skb_gso_segment that does not have CHECKSUM_PARTIAL
checksum offload set.
Commit b2504a5dbe ("net: reduce skb_warn_bad_offload() noise")
observed that SKB_GSO_DODGY producers can trigger the check and
that passing those packets through the GSO handlers will fix it
up. But, the software UFO handler will set ip_summed to
CHECKSUM_NONE.
When __skb_gso_segment is called from the receive path, this
triggers the warning again.
Make UFO set CHECKSUM_UNNECESSARY instead of CHECKSUM_NONE. On
Tx these two are equivalent. On Rx, this better matches the
skb state (checksum computed), as CHECKSUM_NONE here means no
checksum computed.
See also this thread for context:
http://patchwork.ozlabs.org/patch/799015/
Fixes: b2504a5dbe ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e7bc478c9 upstream.
My recent change missed fact that UFO would perform a complete
UDP checksum before segmenting in frags.
In this case skb->ip_summed is set to CHECKSUM_NONE.
We need to add this valid case to skb_needs_check()
Fixes: b2504a5dbe ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2504a5dbe upstream.
Dmitry reported warnings occurring in __skb_gso_segment() [1]
All SKB_GSO_DODGY producers can allow user space to feed
packets that trigger the current check.
We could prevent them from doing so, rejecting packets, but
this might add regressions to existing programs.
It turns out our SKB_GSO_DODGY handlers properly set up checksum
information that is needed anyway when packets needs to be segmented.
By checking again skb_needs_check() after skb_mac_gso_segment(),
we should remove these pesky warnings, at a very minor cost.
With help from Willem de Bruijn
[1]
WARNING: CPU: 1 PID: 6768 at net/core/dev.c:2439 skb_warn_bad_offload+0x2af/0x390 net/core/dev.c:2434
lo: caps=(0x000000a2803b7c69, 0x0000000000000000) len=138 data_len=0 gso_size=15883 gso_type=4 ip_summed=0
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 6768 Comm: syz-executor1 Not tainted 4.9.0 #5
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
ffff8801c063ecd8 ffffffff82346bdf ffffffff00000001 1ffff100380c7d2e
ffffed00380c7d26 0000000041b58ab3 ffffffff84b37e38 ffffffff823468f1
ffffffff84820740 ffffffff84f289c0 dffffc0000000000 ffff8801c063ee20
Call Trace:
[<ffffffff82346bdf>] __dump_stack lib/dump_stack.c:15 [inline]
[<ffffffff82346bdf>] dump_stack+0x2ee/0x3ef lib/dump_stack.c:51
[<ffffffff81827e34>] panic+0x1fb/0x412 kernel/panic.c:179
[<ffffffff8141f704>] __warn+0x1c4/0x1e0 kernel/panic.c:542
[<ffffffff8141f7e5>] warn_slowpath_fmt+0xc5/0x100 kernel/panic.c:565
[<ffffffff8356cbaf>] skb_warn_bad_offload+0x2af/0x390 net/core/dev.c:2434
[<ffffffff83585cd2>] __skb_gso_segment+0x482/0x780 net/core/dev.c:2706
[<ffffffff83586f19>] skb_gso_segment include/linux/netdevice.h:3985 [inline]
[<ffffffff83586f19>] validate_xmit_skb+0x5c9/0xc20 net/core/dev.c:2969
[<ffffffff835892bb>] __dev_queue_xmit+0xe6b/0x1e70 net/core/dev.c:3383
[<ffffffff8358a2d7>] dev_queue_xmit+0x17/0x20 net/core/dev.c:3424
[<ffffffff83ad161d>] packet_snd net/packet/af_packet.c:2930 [inline]
[<ffffffff83ad161d>] packet_sendmsg+0x32ed/0x4d30 net/packet/af_packet.c:2955
[<ffffffff834f0aaa>] sock_sendmsg_nosec net/socket.c:621 [inline]
[<ffffffff834f0aaa>] sock_sendmsg+0xca/0x110 net/socket.c:631
[<ffffffff834f329a>] ___sys_sendmsg+0x8fa/0x9f0 net/socket.c:1954
[<ffffffff834f5e58>] __sys_sendmsg+0x138/0x300 net/socket.c:1988
[<ffffffff834f604d>] SYSC_sendmsg net/socket.c:1999 [inline]
[<ffffffff834f604d>] SyS_sendmsg+0x2d/0x50 net/socket.c:1995
[<ffffffff84371941>] entry_SYSCALL_64_fastpath+0x1f/0xc2
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e44699d2c2 upstream.
Recently I started seeing warnings about pages with refcount -1. The
problem was traced to packets being reused after their head was merged into
a GRO packet by skb_gro_receive(). While bisecting the issue pointed to
commit c21b48cc1b ("net: adjust skb->truesize in ___pskb_trim()") and
I have never seen it on a kernel with it reverted, I believe the real
problem appeared earlier when the option to merge head frag in GRO was
implemented.
Handling NAPI_GRO_FREE_STOLEN_HEAD state was only added to GRO_MERGED_FREE
branch of napi_skb_finish() so that if the driver uses napi_gro_frags()
and head is merged (which in my case happens after the skb_condense()
call added by the commit mentioned above), the skb is reused including the
head that has been merged. As a result, we release the page reference
twice and eventually end up with negative page refcount.
To fix the problem, handle NAPI_GRO_FREE_STOLEN_HEAD in napi_frags_finish()
the same way it's done in napi_skb_finish().
Fixes: d7e8883cfc ("net: make GRO aware of skb->head_frag")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f64ec7451 upstream.
Similar to the fix provided by Dominik Heidler in commit
9b3dc0a17d ("l2tp: cast l2tp traffic counter to unsigned")
we need to take care of 32bit kernels in dev_get_stats().
When using atomic_long_read(), we add a 'long' to u64 and
might misinterpret high order bit, unless we cast to unsigned.
Fixes: caf586e5f2 ("net: add a core netdev->rx_dropped counter")
Fixes: 015f0688f5 ("net: net: add a core netdev->tx_dropped counter")
Fixes: 6e7333d315 ("net: add rx_nohandler stat counter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c28294b941 ]
KMSAN reported a use of uninitialized memory in dev_set_alias(),
which was caused by calling strlcpy() (which in turn called strlen())
on the user-supplied non-terminated string.
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52bd2d62ce upstream.
skb->sender_cpu and skb->napi_id share a common storage,
and we had various bugs about this.
We had to call skb_sender_cpu_clear() in some places to
not leave a prior skb->napi_id and fool netdev_pick_tx()
As suggested by Alexei, we could split the space so that
these errors can not happen.
0 value being reserved as the common (not initialized) value,
let's reserve [1 .. NR_CPUS] range for valid sender_cpu,
and [NR_CPUS+1 .. ~0U] for valid napi_id.
This will allow proper busy polling support over tunnels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 13baa00ad0 ]
It is now very clear that silly TCP listeners might play with
enabling/disabling timestamping while new children are added
to their accept queue.
Meaning net_enable_timestamp() can be called from BH context
while current state of the static key is not enabled.
Lets play safe and allow all contexts.
The work queue is scheduled only under the problematic cases,
which are the static key enable/disable transition, to not slow down
critical paths.
This extends and improves what we did in commit 5fa8bbda38 ("net: use
a work queue to defer net_disable_timestamp() work")
Fixes: b90e5794c5 ("net: dont call jump_label_dec from irq context")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7be2c82cfd ]
Ashizuka reported a highmem oddity and sent a patch for freescale
fec driver.
But the problem root cause is that core networking stack
must ensure no skb with highmem fragment is ever sent through
a device that does not assert NETIF_F_HIGHDMA in its features.
We need to call illegal_highdma() from harmonize_features()
regardless of CSUM checks.
Fixes: ec5f061564 ("net: Kill link between CSUM and SG features.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pravin Shelar <pshelar@ovn.org>
Reported-by: "Ashizuka, Yuusuke" <ashiduka@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7cfd5fd5a9 ]
On 32bit arches, (skb->end - skb->data) is not 'unsigned int',
so we shall use min_t() instead of min() to avoid a compiler error.
Fixes: 1272ce87fa ("gro: Enter slow-path if there is no tailroom")
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1272ce87fa ]
The GRO path has a fast-path where we avoid calling pskb_may_pull
and pskb_expand by directly accessing frag0. However, this should
only be done if we have enough tailroom in the skb as otherwise
we'll have to expand it later anyway.
This patch adds the check by capping frag0_len with the skb tailroom.
Fixes: cb18978cbf ("gro: Open-code final pskb_may_pull")
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4f2e4ad56a ]
Sending zero checksum is ok for TCP, but not for UDP.
UDPv6 receiver should by default drop a frame with a 0 checksum,
and UDPv4 would not verify the checksum and might accept a corrupted
packet.
Simply replace such checksum by 0xffff, regardless of transport.
This error was caught on SIT tunnels, but seems generic.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 104ba78c98 ]
When transmitting on a packet socket with PACKET_VNET_HDR and
PACKET_QDISC_BYPASS, validate device support for features requested
in vnet_hdr.
Drop TSO packets sent to devices that do not support TSO or have the
feature disabled. Note that the latter currently do process those
packets correctly, regardless of not advertising the feature.
Because of SKB_GSO_DODGY, it is not sufficient to test device features
with netif_needs_gso. Full validate_xmit_skb is needed.
Switch to software checksum for non-TSO packets that request checksum
offload if that device feature is unsupported or disabled. Note that
similar to the TSO case, device drivers may perform checksum offload
correctly even when not advertising it.
When switching to software checksum, packets hit skb_checksum_help,
which has two BUG_ON checksum not in linear segment. Packet sockets
always allocate at least up to csum_start + csum_off + 2 as linear.
Tested by running github.com/wdebruij/kerneltools/psock_txring_vnet.c
ethtool -K eth0 tso off tx on
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v -N
ethtool -K eth0 tx off
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G -N
v2:
- add EXPORT_SYMBOL_GPL(validate_xmit_skb_list)
Fixes: d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fcd91dd449 ]
Currently, GRO can do unlimited recursion through the gro_receive
handlers. This was fixed for tunneling protocols by limiting tunnel GRO
to one level with encap_mark, but both VLAN and TEB still have this
problem. Thus, the kernel is vulnerable to a stack overflow, if we
receive a packet composed entirely of VLAN headers.
This patch adds a recursion counter to the GRO layer to prevent stack
overflow. When a gro_receive function hits the recursion limit, GRO is
aborted for this skb and it is processed normally. This recursion
counter is put in the GRO CB, but could be turned into a percpu counter
if we run out of space in the CB.
Thanks to Vladimír Beneš <vbenes@redhat.com> for the initial bug report.
Fixes: CVE-2016-7039
Fixes: 9b174d88c2 ("net: Add Transparent Ethernet Bridging GRO support.")
Fixes: 66e5133f19 ("vlan: Add GRO support for non hardware accelerated vlan")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 93409033ae ]
This is a respin of a patch to fix a relatively easily reproducible kernel
panic related to the all_adj_list handling for netdevs in recent kernels.
The following sequence of commands will reproduce the issue:
ip link add link eth0 name eth0.100 type vlan id 100
ip link add link eth0 name eth0.200 type vlan id 200
ip link add name testbr type bridge
ip link set eth0.100 master testbr
ip link set eth0.200 master testbr
ip link add link testbr mac0 type macvlan
ip link delete dev testbr
This creates an upper/lower tree of (excuse the poor ASCII art):
/---eth0.100-eth0
mac0-testbr-
\---eth0.200-eth0
When testbr is deleted, the all_adj_lists are walked, and eth0 is deleted twice from
the mac0 list. Unfortunately, during setup in __netdev_upper_dev_link, only one
reference to eth0 is added, so this results in a panic.
This change adds reference count propagation so things are handled properly.
Matthias Schiffer reported a similar crash in batman-adv:
https://github.com/freifunk-gluon/gluon/issues/680https://www.open-mesh.org/issues/247
which this patch also seems to resolve.
Signed-off-by: Andrew Collins <acollins@cradlepoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac8e0f579 upstream.
When drivers express support for TSO of encapsulated packets, they
only mean that they can do it for one layer of encapsulation.
Supporting additional levels would mean updating, at a minimum,
more IP length fields and they are unaware of this.
No encapsulation device expresses support for handling offloaded
encapsulated packets, so we won't generate these types of frames
in the transmit path. However, GRO doesn't have a check for
multiple levels of encapsulation and will attempt to build them.
UDP tunnel GRO actually does prevent this situation but it only
handles multiple UDP tunnels stacked on top of each other. This
generalizes that solution to prevent any kind of tunnel stacking
that would cause problems.
Fixes: bf5a755f ("net-gre-gro: Add GRE support to the GRO stack")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Juerg Haefliger <juerg.haefliger@hpe.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 24b27fc4cd ]
Following few steps will crash kernel -
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a813104d92 ]
My implementation around IFF_NO_QUEUE driver flag assumed that leaving
tx_queue_len untouched (specifically: not setting it to zero) by drivers
would make it possible to assign a regular qdisc to them without having
to worry about setting tx_queue_len to a useful value. This was only
partially true: I overlooked that some drivers don't call ether_setup()
and therefore not initialize tx_queue_len to the default value of 1000.
Consequently, removing the workarounds in place for that case in qdisc
implementations which cared about it (namely, pfifo, bfifo, gred, htb,
plug and sfb) leads to problems with these specific interface types and
qdiscs.
Luckily, there's already a sanitization point for drivers setting
tx_queue_len to zero, which can be reused to assign the fallback value
most qdisc implementations used, which is 1.
Fixes: 348e3435cb ("net: sched: drop all special handling of tx_queue_len == 0")
Tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce87fc6ce3 ]
GRO is currently not aware of tunnel metadata generated by lightweight
tunnels and stored in the dst. This leads to two possible problems:
* Incorrectly merging two frames that have different metadata.
* Leaking of allocated metadata from merged frames.
This avoids those problems by comparing the tunnel information before
merging, similar to how we handle other metadata (such as vlan tags),
and releasing any state when we are done.
Reported-by: John <john.phillips5@hpe.com>
Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9207f9d45b ]
Skb_gso_segment() uses skb control block during segmentation.
This patch adds 32-bytes room for previous control block which
will be copied into all resulting segments.
This patch fixes kernel crash during fragmenting forwarded packets.
Fragmentation requires valid IP CB in skb for clearing ip options.
Also patch removes custom save/restore in ovs code, now it's redundant.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Link: http://lkml.kernel.org/r/CALYGNiP-0MZ-FExV2HutTvE9U-QQtkKSoE--KN=JQE5STYsjAA@mail.gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 00ee592717 ("net: fix __netdev_update_features return
on ndo_set_features failure")
and adds a comment explaining why it's okay to return a value other than
0 upon error. Some drivers might actually change flags and return an
error so it's better to fire a spurious notification rather than miss
these.
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent flaw in the netdev feature setting resulted in warnings
like this one from VLAN interfaces:
WARNING: CPU: 1 PID: 4975 at net/core/dev.c:2419 skb_warn_bad_offload+0xbc/0xcb()
: caps=(0x00000000001b5820, 0x00000000001b5829) len=2782 data_len=0 gso_size=1348 gso_type=16 ip_summed=3
The ":" is supposed to be preceded by a driver name, but in this
case it is an empty string since the device has no parent.
There are many types of network devices without a parent. The
anonymous warnings for these devices can be hard to debug. Log
the network device name instead in these cases to assist further
debugging.
This is mostly similar to how __netdev_printk() handles orphan
devices.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ndo_set_features fails __netdev_update_features() will return -1 but
this is wrong because it is expected to return 0 if no features were
changed (see netdev_update_features()), which will cause a netdev
notifier to be called without any actual changes. Fix this by returning
0 if ndo_set_features fails.
Fixes: 6cb6a27c45 ("net: Call netdev_features_change() from netdev_update_features()")
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With moving netdev_sync_lower_features() after the .ndo_set_features
calls, I neglected to verify that devices added *after* a flag had been
disabled on an upper device were properly added with that flag disabled as
well. This currently happens, because we exit __netdev_update_features()
when we see dev->features == features for the upper dev. We can retain the
optimization of leaving without calling .ndo_set_features with a bit of
tweaking and a goto here.
Fixes: fd867d51f8 ("net/core: generic support for disabling netdev features down stack")
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Nikolay Aleksandrov <razor@blackwall.org>
CC: Michal Kubecek <mkubecek@suse.cz>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: netdev@vger.kernel.org
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Nikolay and further explained by Geert, the initial
for_each_netdev_feature macro was broken, as feature would get set outside
of the block of code it was intended to run in, thus only ever working for
the first feature bit in the mask. While less pretty this way, this is
tested and confirmed functional with multiple feature bits set in
NETIF_F_UPPER_DISABLES.
[root@dell-per730-01 ~]# ethtool -K bond0 lro off
...
[ 242.761394] bond0: Disabling feature 0x0000000000008000 on lower dev p5p2.
[ 243.552178] bnx2x 0000:06:00.1 p5p2: using MSI-X IRQs: sp 74 fp[0] 76 ... fp[7] 83
[ 244.353978] bond0: Disabling feature 0x0000000000008000 on lower dev p5p1.
[ 245.147420] bnx2x 0000:06:00.0 p5p1: using MSI-X IRQs: sp 62 fp[0] 64 ... fp[7] 71
[root@dell-per730-01 ~]# ethtool -K bond0 gro off
...
[ 251.925645] bond0: Disabling feature 0x0000000000004000 on lower dev p5p2.
[ 252.713693] bnx2x 0000:06:00.1 p5p2: using MSI-X IRQs: sp 74 fp[0] 76 ... fp[7] 83
[ 253.499085] bond0: Disabling feature 0x0000000000004000 on lower dev p5p1.
[ 254.290922] bnx2x 0000:06:00.0 p5p1: using MSI-X IRQs: sp 62 fp[0] 64 ... fp[7] 71
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Nikolay Aleksandrov <razor@blackwall.org>
CC: Michal Kubecek <mkubecek@suse.cz>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some netdev features, which when disabled on an upper device,
such as a bonding master or a bridge, must be disabled and cannot be
re-enabled on underlying devices.
This is a rework of an earlier more heavy-handed appraoch, which simply
disables and prevents re-enabling of netdev features listed in a new
define in include/net/netdev_features.h, NETIF_F_UPPER_DISABLES. Any upper
device that disables a flag in that feature mask, the disabling will
propagate down the stack, and any lower device that has any upper device
with one of those flags disabled should not be able to enable said flag.
Initially, only LRO is included for proof of concept, and because this
code effectively does the same thing as dev_disable_lro(), though it will
also activate from the ethtool path, which was one of the goals here.
[root@dell-per730-01 ~]# ethtool -k bond0 |grep large
large-receive-offload: on
[root@dell-per730-01 ~]# ethtool -k p5p1 |grep large
large-receive-offload: on
[root@dell-per730-01 ~]# ethtool -K bond0 lro off
[root@dell-per730-01 ~]# ethtool -k bond0 |grep large
large-receive-offload: off
[root@dell-per730-01 ~]# ethtool -k p5p1 |grep large
large-receive-offload: off
dmesg dump:
[ 1033.277986] bond0: Disabling feature 0x0000000000008000 on lower dev p5p2.
[ 1034.067949] bnx2x 0000:06:00.1 p5p2: using MSI-X IRQs: sp 74 fp[0] 76 ... fp[7] 83
[ 1034.753612] bond0: Disabling feature 0x0000000000008000 on lower dev p5p1.
[ 1035.591019] bnx2x 0000:06:00.0 p5p1: using MSI-X IRQs: sp 62 fp[0] 64 ... fp[7] 71
This has been successfully tested with bnx2x, qlcnic and netxen network
cards as slaves in a bond interface. Turning LRO on or off on the master
also turns it on or off on each of the slaves, new slaves are added with
LRO in the same state as the master, and LRO can't be toggled on the
slaves.
Also, this should largely remove the need for dev_disable_lro(), and most,
if not all, of its call sites can be replaced by simply making sure
NETIF_F_LRO isn't included in the relevant device's feature flags.
Note that this patch is driven by bug reports from users saying it was
confusing that bonds and slaves had different settings for the same
features, and while it won't be 100% in sync if a lower device doesn't
support a feature like LRO, I think this is a good step in the right
direction.
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Nikolay Aleksandrov <razor@blackwall.org>
CC: Michal Kubecek <mkubecek@suse.cz>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
While transitioning to netdev based vport we broke OVS
feature which allows user to retrieve tunnel packet egress
information for lwtunnel devices. Following patch fixes it
by introducing ndo operation to get the tunnel egress info.
Same ndo operation can be used for lwtunnel devices and compat
ovs-tnl-vport devices. So after adding such device operation
we can remove similar operation from ovs-vport.
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This newly introduced netdevice notifier is called before actual change
upper happens. That provides a possibility for notifier handlers to
know upper change will happen and react to it, including possibility to
forbid the change. That is valuable for drivers which can check if the
upper device linkage is supported and forbid that in case it is not.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYN_RECV & TIMEWAIT sockets are not full blown, they do not have a
sk_dst_cache pointer.
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
The __netdev_find_adj() helper does not use its first argument, only the
device to find and list to walk through.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers might call napi_disable while not holding the napi instance poll_lock.
In those instances, its possible for a race condition to exist between
poll_one_napi and napi_disable. That is to say, poll_one_napi only tests the
NAPI_STATE_SCHED bit to see if there is work to do during a poll, and as such
the following may happen:
CPU0 CPU1
ndo_tx_timeout napi_poll_dev
napi_disable poll_one_napi
test_and_set_bit (ret 0)
test_bit (ret 1)
reset adapter napi_poll_routine
If the adapter gets a tx timeout without a napi instance scheduled, its possible
for the adapter to think it has exclusive access to the hardware (as the napi
instance is now scheduled via the napi_disable call), while the netpoll code
thinks there is simply work to do. The result is parallel hardware access
leading to corrupt data structures in the driver, and a crash.
Additionaly, there is another, more critical race between netpoll and
napi_disable. The disabled napi state is actually identical to the scheduled
state for a given napi instance. The implication being that, if a napi instance
is disabled, a netconsole instance would see the napi state of the device as
having been scheduled, and poll it, likely while the driver was dong something
requiring exclusive access. In the case above, its fairly clear that not having
the rings in a state ready to be polled will cause any number of crashes.
The fix should be pretty easy. netpoll uses its own bit to indicate that that
the napi instance is in a state of being serviced by netpoll (NAPI_STATE_NPSVC).
We can just gate disabling on that bit as well as the sched bit. That should
prevent netpoll from conducting a napi poll if we convert its set bit to a
test_and_set_bit operation to provide mutual exclusion
Change notes:
V2)
Remove a trailing whtiespace
Resubmit with proper subject prefix
V3)
Clean up spacing nits
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: jmaxwell@redhat.com
Tested-by: jmaxwell@redhat.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing bpf_clone_redirect() helper clones skb before redirecting
it to RX or TX of destination netdev.
Introduce bpf_redirect() helper that does that without cloning.
Benchmarked with two hosts using 10G ixgbe NICs.
One host is doing line rate pktgen.
Another host is configured as:
$ tc qdisc add dev $dev ingress
$ tc filter add dev $dev root pref 10 u32 match u32 0 0 flowid 1:2 \
action bpf run object-file tcbpf1_kern.o section clone_redirect_xmit drop
so it receives the packet on $dev and immediately xmits it on $dev + 1
The section 'clone_redirect_xmit' in tcbpf1_kern.o file has the program
that does bpf_clone_redirect() and performance is 2.0 Mpps
$ tc filter add dev $dev root pref 10 u32 match u32 0 0 flowid 1:2 \
action bpf run object-file tcbpf1_kern.o section redirect_xmit drop
which is using bpf_redirect() - 2.4 Mpps
and using cls_bpf with integrated actions as:
$ tc filter add dev $dev root pref 10 \
bpf run object-file tcbpf1_kern.o section redirect_xmit integ_act classid 1
performance is 2.5 Mpps
To summarize:
u32+act_bpf using clone_redirect - 2.0 Mpps
u32+act_bpf using redirect - 2.4 Mpps
cls_bpf using redirect - 2.5 Mpps
For comparison linux bridge in this setup is doing 2.1 Mpps
and ixgbe rx + drop in ip_rcv - 7.8 Mpps
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is immediately motivated by the bridge code that chains functions that
call into netfilter. Without passing net into the okfns the bridge code would
need to guess about the best expression for the network namespace to process
packets in.
As net is frequently one of the first things computed in continuation functions
after netfilter has done it's job passing in the desired network namespace is in
many cases a code simplification.
To support this change the function dst_output_okfn is introduced to
simplify passing dst_output as an okfn. For the moment dst_output_okfn
just silently drops the struct net.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_receive_skb_sk is only called once in the bridge code, replace
it with a bridge specific function that calls netif_receive_skb.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A function with weird arguments that it will never use to accomdate a
netfilter callback prototype is absolutely in the core of the
networking stack. Frankly it does not make sense and it causes a lot
of confusion as to why arguments that are never used are being passed
to the function.
As I am preparing to make a second change to arguments to the okfn even
the names stops making sense.
As I have removed the two callers of this function remove this confusion
from the networking stack.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing a warning in alloc_netdev_mqs() if tx_queue_len is zero and
IFF_NO_QUEUE not set is not appropriate since drivers may use one of the
alloc_netdev* macros instead of alloc_etherdev*, thereby not
intentionally leaving tx_queue_len uninitialized. Instead check here if
tx_queue_len is zero and set IFF_NO_QUEUE, so the value of tx_queue_len
can be ignored in net/sched_generic.c.
Fixes: 906470c ("net: warn if drivers set tx_queue_len = 0")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add info that is passed along with NETDEV_CHANGEUPPER event.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For classifiers getting invoked via tc_classify(), we always need an
extra function call into tc_classify_compat(), as both are being
exported as symbols and tc_classify() itself doesn't do much except
handling of reclassifications when tp->classify() returned with
TC_ACT_RECLASSIFY.
CBQ and ATM are the only qdiscs that directly call into tc_classify_compat(),
all others use tc_classify(). When tc actions are being configured
out in the kernel, tc_classify() effectively does nothing besides
delegating.
We could spare this layer and consolidate both functions. pktgen on
single CPU constantly pushing skbs directly into the netif_receive_skb()
path with a dummy classifier on ingress qdisc attached, improves
slightly from 22.3Mpps to 23.1Mpps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the introduction of IFF_NO_QUEUE, there is a better way for
drivers to indicate that no qdisc should be attached by default. Though,
the old convention can't be dropped since ignoring that setting would
break drivers still using it. Instead, add a warning so out-of-tree
driver maintainers get a chance to adjust their code before we finally
get rid of any special handling of tx_queue_len == 0.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following typo
- unchainged -> unchanged
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
