[ Upstream commit cc1a267986 ]
Since struct _mic_vring_info and vring are allocated together and follow
vring, if the vring_size() is not four bytes aligned, which will cause
the start address of struct _mic_vring_info is not four byte aligned.
For example, when vring entries is 128, the vring_size() will be 5126
bytes. The _mic_vring_info struct layout in ddr looks like:
0x90002400: 00000000 00390000 EE010000 0000C0FF
Here 0x39 is the avail_idx member, and 0xC0FFEE01 is the magic member.
When EP use ioread32(magic) to reads the magic in RC's share memory, it
will cause kernel panic on ARM64 platform due to the cross-byte io read.
Here read magic in user space use le32toh(vr0->info->magic) will meet
the same issue.
So add round_up(x,4) for vring_size, then the struct _mic_vring_info
will store in this way:
0x90002400: 00000000 00000000 00000039 C0FFEE01
Which will avoid kernel panic when read magic in struct _mic_vring_info.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929091106.24624-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90ca6333fd ]
In a couple of places in qp_host_get_user_memory(),
get_user_pages_fast() is called without properly checking for errors. If
e.g. -EFAULT is returned, this negative value will then be passed on to
qp_release_pages(), which expects a u64 as input.
Fix this by only calling qp_release_pages() when we have a positive
number returned.
Fixes: 06164d2b72 ("VMCI: queue pairs implementation.")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200825164522.412392-1-alex.dewar90@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bb04b1923 ]
TI's AM654x PCIe EP has a restriction that BAR_0 is mapped to
application registers. "PCIe Inbound Address Translation" section in
AM65x Sitara Processors TRM (SPRUID7 – April 2018) describes BAR0 as
reserved.
Configure pci_endpoint_test to use BAR_2 instead.
Also set alignment to 64K since "PCIe Subsystem Address Translation"
section in TRM indicates minimum ATU window size is 64K.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7a839dbab1 upstream.
DMA transfers to and from the SD card stall for 10 seconds and run into
timeout on RTS5260 card readers after ASPM was enabled.
Adding a short msleep after disabling ASPM fixes the issue on several
Dell Precision 7530/7540 systems I tested.
This function is only called when waking up after the chip went into
power-save after not transferring data for a few seconds. The added
msleep does therefore not change anything in data transfer speed or
induce any excessive waiting while data transfers are running, or the
chip is sleeping. Only the transition from sleep to active is affected.
Signed-off-by: Klaus Doth <kdlnx@doth.eu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/4434eaa7-2ee3-a560-faee-6cee63ebd6d4@doth.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 85dc2c65e6 ]
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/misc/echo/echo.c:384:27: warning: equality comparison with
extraneous parentheses [-Wparentheses-equality]
if ((ec->nonupdate_dwell == 0)) {
~~~~~~~~~~~~~~~~~~~~^~~~
drivers/misc/echo/echo.c:384:27: note: remove extraneous parentheses
around the comparison to silence this warning
if ((ec->nonupdate_dwell == 0)) {
~ ^ ~
drivers/misc/echo/echo.c:384:27: note: use '=' to turn this equality
comparison into an assignment
if ((ec->nonupdate_dwell == 0)) {
^~
=
1 warning generated.
Remove them and while we're at it, simplify the zero check as '!var' is
used more than 'var == 0'.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b2ba9225e0 upstream.
commit e03327122e ("pci_endpoint_test: Add 2 ioctl commands")
uses module parameter 'irqtype' in pci_endpoint_test_set_irq()
to check if IRQ vectors of a particular type (MSI or MSI-X or
LEGACY) is already allocated. However with multi-function devices,
'irqtype' will not correctly reflect the IRQ type of the PCI device.
Fix it here by adding 'irqtype' for each PCI device to show the
IRQ type of a particular PCI device.
Fixes: e03327122e ("pci_endpoint_test: Add 2 ioctl commands")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b443e5c80 upstream.
Adding more than 10 pci-endpoint-test devices results in
"kobject_add_internal failed for pci-endpoint-test.1 with -EEXIST, don't
try to register things with the same name in the same directory". This
is because commit 2c156ac71c ("misc: Add host side PCI driver for PCI
test function device") limited the length of the "name" to 20 characters.
Change the length of the name to 24 in order to support upto 10000
pci-endpoint-test devices.
Fixes: 2c156ac71c ("misc: Add host side PCI driver for PCI test function device")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3745488e9d ]
altera_get_note is called from altera_init, where key is kzalloc(33).
When the allocation functions are annotated to allow the compiler to see
the sizes of objects, and with FORTIFY_SOURCE, we see:
In file included from drivers/misc/altera-stapl/altera.c:14:0:
In function ‘strlcpy’,
inlined from ‘altera_init’ at drivers/misc/altera-stapl/altera.c:2189:5:
include/linux/string.h:378:4: error: call to ‘__write_overflow’ declared with attribute error: detected write beyond size of object passed as 1st parameter
__write_overflow();
^~~~~~~~~~~~~~~~~~
That refers to this code in altera_get_note:
if (key != NULL)
strlcpy(key, &p[note_strings +
get_unaligned_be32(
&p[note_table + (8 * i)])],
length);
The error triggers because the length of 'key' is 33, but the copy
uses length supplied as the 'length' parameter, which is always
256. Split the size parameter into key_len and val_len, and use the
appropriate length depending on what is being copied.
Detected by compiler error, only compile-tested.
Cc: "Igor M. Liplianin" <liplianin@netup.ru>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Link: https://lore.kernel.org/r/20200120074344.504-2-dja@axtens.net
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/202002251042.D898E67AC@keescook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc83f79bd2 ]
Generally, declaring a platform device as a static variable is
a bad idea and can cause all kinds of problems, in particular
with the DMA configuration and lifetime rules.
A specific problem we hit here is from a bug in clang that warns
about certain (otherwise valid) macros when used in static variables:
drivers/misc/mic/card/mic_x100.c:285:27: warning: shift count >= width of type [-Wshift-count-overflow]
static u64 mic_dma_mask = DMA_BIT_MASK(64);
^~~~~~~~~~~~~~~~
include/linux/dma-mapping.h:141:54: note: expanded from macro 'DMA_BIT_MASK'
#define DMA_BIT_MASK(n) (((n) == 64) ? ~0ULL : ((1ULL<<(n))-1))
^ ~~~
A slightly better way here is to create the platform device dynamically
and set the dma mask in the probe function.
This avoids the warning and some other problems, but is still not ideal
because the device creation should really be separated from the driver,
and the fact that the device has no parent means we have to force
the dma mask rather than having it set up from the bus that the device
is actually on.
Fixes: dd8d8d44df ("misc: mic: MIC card driver specific changes to enable SCIF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190712092426.872625-1-arnd@arndb.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0576f9ecb ]
Clang warns:
drivers/misc/sgi-xp/xpc_partition.c:73:14: warning: variable 'buf' is
uninitialized when used within its own initialization [-Wuninitialized]
void *buf = buf;
~~~ ^~~
1 warning generated.
Arnd's explanation during review:
/*
* Returns the physical address of the partition's reserved page through
* an iterative number of calls.
*
* On first call, 'cookie' and 'len' should be set to 0, and 'addr'
* set to the nasid of the partition whose reserved page's address is
* being sought.
* On subsequent calls, pass the values, that were passed back on the
* previous call.
*
* While the return status equals SALRET_MORE_PASSES, keep calling
* this function after first copying 'len' bytes starting at 'addr'
* into 'buf'. Once the return status equals SALRET_OK, 'addr' will
* be the physical address of the partition's reserved page. If the
* return status equals neither of these, an error as occurred.
*/
static inline s64
sn_partition_reserved_page_pa(u64 buf, u64 *cookie, u64 *addr, u64 *len)
so *len is set to zero on the first call and tells the bios how many
bytes are accessible at 'buf', and it does get updated by the BIOS to
tell us how many bytes it needs, and then we allocate that and try again.
Fixes: 2792902946 ("[IA64-SGI] cleanup the way XPC locates the reserved page")
Link: https://github.com/ClangBuiltLinux/linux/issues/466
Suggested-by: Stephen Hines <srhines@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03b2cbb6ea ]
Looks like during merging the bulk POLL* -> EPOLL* replacement
missed the patch
'commit af336cabe0 ("mei: limit the number of queued writes")'
Fix sparse warning:
drivers/misc/mei/main.c:602:13: warning: restricted __poll_t degrades to integer
drivers/misc/mei/main.c:605:30: warning: invalid assignment: |=
drivers/misc/mei/main.c:605:30: left side has type restricted __poll_t
drivers/misc/mei/main.c:605:30: right side has type int
Fixes: af336cabe0 ("mei: limit the number of queued writes")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 529244bd1a upstream.
Doing an add/remove/add on a SCSI device in an enclosure leads to an oops
caused by poisoned values in the enclosure device list pointers. The
reason is because we are keeping the enclosure device across the enclosed
device add/remove/add but the current code is doing a
device_add/device_del/device_add on it. This is the wrong thing to do in
sysfs, so fix it by not doing a device_del on the enclosure device simply
because of a hot remove of the drive in the slot.
[mkp: added missing email addresses]
Fixes: 43d8eb9cfd ("[SCSI] ses: add support for enclosure component hot removal")
Link: https://lore.kernel.org/r/1578532892.3852.10.camel@HansenPartnership.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reported-by: Luo Jiaxing <luojiaxing@huawei.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ccb645683 ]
Currently the null check on key is occurring after the strcasecmp on
the key, hence there is a potential null pointer dereference on key.
Fix this by checking if key is null first. Also replace the == 0
check on strcasecmp with just the ! operator.
Detected by CoverityScan, CID#1248787 ("Dereference before null check")
Fixes: fa766c9be5 ("[media] Altera FPGA firmware download module")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b995f4eec ]
In _scif_prog_signal(), the boolean variable 'x100' is used to indicate
whether the MIC Coprocessor is X100. If 'x100' is true, the status
descriptor will be used to write the value to the destination. Otherwise, a
DMA pool will be allocated for this purpose. Specifically, if the DMA pool
is allocated successfully, two memory addresses will be returned. One is
for the CPU and the other is for the device to access the DMA pool. The
former is stored to the variable 'status' and the latter is stored to the
variable 'src'. After the allocation, the address in 'src' is saved to
'status->src_dma_addr', which is actually in the DMA pool, and 'src' is
then modified.
Later on, if an error occurs, the execution flow will transfer to the label
'dma_fail', which will check 'x100' and free up the allocated DMA pool if
'x100' is false. The point here is that 'status->src_dma_addr' is used for
freeing up the DMA pool. As mentioned before, 'status->src_dma_addr' is in
the DMA pool. And thus, the device is able to modify this data. This can
potentially cause failures when freeing up the DMA pool because of the
modified device address.
This patch avoids the above issue by using the variable 'src' (with
necessary calculation) to free up the DMA pool.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02241995b0 ]
The function should return -EFAULT when copy_from_user fails. Even
though the caller does not distinguish them. but we should keep backward
compatibility.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa0218ef73 ]
kgdbts current fails when compiled with restrict:
drivers/misc/kgdbts.c: In function ‘configure_kgdbts’:
drivers/misc/kgdbts.c:1070:2: error: ‘strcpy’ source argument is the same as destination [-Werror=restrict]
strcpy(config, opt);
^~~~~~~~~~~~~~~~~~~
As the error says, config is being used in both the source and destination.
Refactor the code to avoid the extra copy and put the parsing closer to
the actual location.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ba03a9bbd1 upstream.
Francois reported that VMware balloon gets stuck after a balloon reset,
when the VMCI doorbell is removed. A similar error can occur when the
balloon driver is removed with the following splat:
[ 1088.622000] INFO: task modprobe:3565 blocked for more than 120 seconds.
[ 1088.622035] Tainted: G W 5.2.0 #4
[ 1088.622087] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1088.622205] modprobe D 0 3565 1450 0x00000000
[ 1088.622210] Call Trace:
[ 1088.622246] __schedule+0x2a8/0x690
[ 1088.622248] schedule+0x2d/0x90
[ 1088.622250] schedule_timeout+0x1d3/0x2f0
[ 1088.622252] wait_for_completion+0xba/0x140
[ 1088.622320] ? wake_up_q+0x80/0x80
[ 1088.622370] vmci_resource_remove+0xb9/0xc0 [vmw_vmci]
[ 1088.622373] vmci_doorbell_destroy+0x9e/0xd0 [vmw_vmci]
[ 1088.622379] vmballoon_vmci_cleanup+0x6e/0xf0 [vmw_balloon]
[ 1088.622381] vmballoon_exit+0x18/0xcc8 [vmw_balloon]
[ 1088.622394] __x64_sys_delete_module+0x146/0x280
[ 1088.622408] do_syscall_64+0x5a/0x130
[ 1088.622410] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1088.622415] RIP: 0033:0x7f54f62791b7
[ 1088.622421] Code: Bad RIP value.
[ 1088.622421] RSP: 002b:00007fff2a949008 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ 1088.622426] RAX: ffffffffffffffda RBX: 000055dff8b55d00 RCX: 00007f54f62791b7
[ 1088.622426] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 000055dff8b55d68
[ 1088.622427] RBP: 000055dff8b55d00 R08: 00007fff2a947fb1 R09: 0000000000000000
[ 1088.622427] R10: 00007f54f62f5cc0 R11: 0000000000000206 R12: 000055dff8b55d68
[ 1088.622428] R13: 0000000000000001 R14: 000055dff8b55d68 R15: 00007fff2a94a3f0
The cause for the bug is that when the "delayed" doorbell is invoked, it
takes a reference on the doorbell entry and schedules work that is
supposed to run the appropriate code and drop the doorbell entry
reference. The code ignores the fact that if the work is already queued,
it will not be scheduled to run one more time. As a result one of the
references would not be dropped. When the code waits for the reference
to get to zero, during balloon reset or module removal, it gets stuck.
Fix it. Drop the reference if schedule_work() indicates that the work is
already queued.
Note that this bug got more apparent (or apparent at all) due to
commit ce664331b2 ("vmw_balloon: VMCI_DOORBELL_SET does not check status").
Fixes: 83e2ec765b ("VMCI: doorbell implementation.")
Reported-by: Francois Rigault <rigault.francois@gmail.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: Adit Ranadive <aditr@vmware.com>
Cc: Alexios Zavras <alexios.zavras@intel.com>
Cc: Vishnu DASA <vdasa@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20190820202638.49003-1-namit@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c2eb5b285 upstream.
The VMCI handle array has an integer overflow in
vmci_handle_arr_append_entry when it tries to expand the array. This can be
triggered from a guest, since the doorbell link hypercall doesn't impose a
limit on the number of doorbell handles that a VM can create in the
hypervisor, and these handles are stored in a handle array.
In this change, we introduce a mandatory max capacity for handle
arrays/lists to avoid excessive memory usage.
Signed-off-by: Vishnu Dasa <vdasa@vmware.com>
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9e08a0738 upstream.
With CONFIG_LKDTM=y and make OBJCOPY=llvm-objcopy, llvm-objcopy errors:
llvm-objcopy: error: --set-section-flags=.text conflicts with
--rename-section=.text=.rodata
Rather than support setting flags then renaming sections vs renaming
then setting flags, it's simpler to just change both at the same time
via --rename-section. Adding the load flag is required for GNU objcopy
to mark .rodata Type as PROGBITS after the rename.
This can be verified with:
$ readelf -S drivers/misc/lkdtm/rodata_objcopy.o
...
Section Headers:
[Nr] Name Type Address Offset
Size EntSize Flags Link Info Align
...
[ 1] .rodata PROGBITS 0000000000000000 00000040
0000000000000004 0000000000000000 A 0 0 4
...
Which shows that .text is now renamed .rodata, the alloc flag A is set,
the type is PROGBITS, and the section is not flagged as writeable W.
Cc: stable@vger.kernel.org
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=24554
Link: https://github.com/ClangBuiltLinux/linux/issues/448
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Suggested-by: Alan Modra <amodra@gmail.com>
Suggested-by: Jordan Rupprect <rupprecht@google.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a9e295e7c upstream.
Within at24_loop_until_timeout the timestamp used for timeout checking
is recorded after the I2C transfer and sleep_range(). Under high CPU
load either the execution time for I2C transfer or sleep_range() could
actually be larger than the timeout value. Worst case the I2C transfer
is only tried once because the loop will exit due to the timeout
although the EEPROM is now ready.
To fix this issue the timestamp is recorded at the beginning of each
iteration. That is, before I2C transfer and sleep. Then the timeout
is actually checked against the timestamp of the previous iteration.
This makes sure that even if the timeout is reached, there is still one
more chance to try the I2C transfer in case the EEPROM is ready.
Example:
If you have a system which combines high CPU load with repeated EEPROM
writes you will run into the following scenario.
- System makes a successful regmap_bulk_write() to EEPROM.
- System wants to perform another write to EEPROM but EEPROM is still
busy with the last write.
- Because of high CPU load the usleep_range() will sleep more than
25 ms (at24_write_timeout).
- Within the over-long sleeping the EEPROM finished the previous write
operation and is ready again.
- at24_loop_until_timeout() will detect timeout and won't try to write.
Signed-off-by: Wang Xin <xin.wang7@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b281218ad4 ]
There is an out-of-bounds access to "config[len - 1]" array when the
variable "len" is zero.
See commit dada6a43b0 ("kgdboc: fix KASAN global-out-of-bounds bug
in param_set_kgdboc_var()") for details.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f22066457 ]
commit 834b905199 ("misc: pci_endpoint_test: Add support for
PCI_ENDPOINT_TEST regs to be mapped to any BAR") while adding
test_reg_bar in order to map PCI_ENDPOINT_TEST regs to be mapped to any
BAR failed to update test_reg_bar in pci_endpoint_test, resulting in
test_reg_bar having invalid value when used outside probe.
Fix it.
Fixes: 834b905199 ("misc: pci_endpoint_test: Add support for PCI_ENDPOINT_TEST regs to be mapped to any BAR")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 110080cea0 upstream.
There are a couple potential integer overflows here.
round_up(m->size + (m->addr & ~PAGE_MASK), PAGE_SIZE);
The first thing is that the "m->size + (...)" addition could overflow,
and the second is that round_up() overflows to zero if the result is
within PAGE_SIZE of the type max.
In this code, the "m->size" variable is an u64 but we're saving the
result in "map_size" which is an unsigned long and genwqe_user_vmap()
takes an unsigned long as well. So I have used ULONG_MAX as the upper
bound. From a practical perspective unsigned long is fine/better than
trying to change all the types to u64.
Fixes: eaf4722d46 ("GenWQE Character device and DDCB queue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59a12205d3 ]
Introduce lkdtm tests for NULL pointer dereference: check access or exec
at NULL address, since these errors tend to be reported differently from
the general fault error text. For example from x86:
pr_alert("BUG: unable to handle kernel %s at %px\n",
address < PAGE_SIZE ? "NULL pointer dereference" : "paging request",
(void *)address);
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c411157a4 ]
Today, when doing a lkdtm test before the readiness of the
random generator, (ptrval) is printed instead of the address
at which it perform the fault:
[ 1597.337030] lkdtm: Performing direct entry EXEC_USERSPACE
[ 1597.337142] lkdtm: attempting ok execution at (ptrval)
[ 1597.337398] lkdtm: attempting bad execution at (ptrval)
[ 1597.337460] kernel tried to execute user page (77858000) -exploit attempt? (uid: 0)
[ 1597.344769] Unable to handle kernel paging request for instruction fetch
[ 1597.351392] Faulting instruction address: 0x77858000
[ 1597.356312] Oops: Kernel access of bad area, sig: 11 [#1]
If the lkdtm test is done later on, it prints an hashed address.
In both cases this is pointless. The purpose of the test is to
ensure the kernel generates an Oops at the expected address,
so real addresses needs to be printed. This patch fixes that.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
