There are 2 ways in which a DSA user port may become handled by 2 CPU
ports in a LAG:
(1) its current DSA master joins a LAG
ip link del bond0 && ip link add bond0 type bond mode 802.3ad
ip link set eno2 master bond0
When this happens, all user ports with "eno2" as DSA master get
automatically migrated to "bond0" as DSA master.
(2) it is explicitly configured as such by the user
# Before, the DSA master was eno3
ip link set swp0 type dsa master bond0
The design of this configuration is that the LAG device dynamically
becomes a DSA master through dsa_master_setup() when the first physical
DSA master becomes a LAG slave, and stops being so through
dsa_master_teardown() when the last physical DSA master leaves.
A LAG interface is considered as a valid DSA master only if it contains
existing DSA masters, and no other lower interfaces. Therefore, we
mainly rely on method (1) to enter this configuration.
Each physical DSA master (LAG slave) retains its dev->dsa_ptr for when
it becomes a standalone DSA master again. But the LAG master also has a
dev->dsa_ptr, and this is actually duplicated from one of the physical
LAG slaves, and therefore needs to be balanced when LAG slaves come and
go.
To the switch driver, putting DSA masters in a LAG is seen as putting
their associated CPU ports in a LAG.
We need to prepare cross-chip host FDB notifiers for CPU ports in a LAG,
by calling the driver's ->lag_fdb_add method rather than ->port_fdb_add.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drivers could refuse to offload a LAG configuration for a variety of
reasons, mainly having to do with its TX type. Additionally, since DSA
masters may now also be LAG interfaces, and this will translate into a
call to port_lag_join on the CPU ports, there may be extra restrictions
there. Propagate the netlink extack to this DSA method in order for
drivers to give a meaningful error message back to the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some DSA switches have multiple CPU ports, which can be used to improve
CPU termination throughput, but DSA, through dsa_tree_setup_cpu_ports(),
sets up only the first one, leading to suboptimal use of hardware.
The desire is to not change the default configuration but to permit the
user to create a dynamic mapping between individual user ports and the
CPU port that they are served by, configurable through rtnetlink. It is
also intended to permit load balancing between CPU ports, and in that
case, the foreseen model is for the DSA master to be a bonding interface
whose lowers are the physical DSA masters.
To that end, we create a struct rtnl_link_ops for DSA user ports with
the "dsa" kind. We expose the IFLA_DSA_MASTER link attribute that
contains the ifindex of the newly desired DSA master.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There is a desire to support for DSA masters in a LAG.
That configuration is intended to work by simply enslaving the master to
a bonding/team device. But the physical DSA master (the LAG slave) still
has a dev->dsa_ptr, and that cpu_dp still corresponds to the physical
CPU port.
However, we would like to be able to retrieve the LAG that's the upper
of the physical DSA master. In preparation for that, introduce a helper
called dsa_port_get_master() that replaces all occurrences of the
dp->cpu_dp->master pattern. The distinction between LAG and non-LAG will
be made later within the helper itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Allow to offload L2TPv3 filters by adding flow_rule_match_l2tpv3.
Drivers can extract L2TPv3 specific fields from now on.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Allow to dissect L2TPv3 specific field which is:
- session ID (32 bits)
L2TPv3 might be transported over IP or over UDP,
this implementation is only about L2TPv3 over IP.
IP protocol carries L2TPv3 when ip_proto is
IPPROTO_L2TP (115).
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Each tc action module has a corresponding net_id, so put net_id directly
into the structure tc_action_ops.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
The following set contains changes for your *net-next* tree:
- make conntrack ignore packets that are delayed (containing
data already acked). The current behaviour to flag them as INVALID
causes more harm than good, let them pass so peer can send an
immediate ACK for the most recent sequence number.
- make conntrack recognize when both peers have sent 'invalid' FINs:
This helps cleaning out stale connections faster for those cases where
conntrack is no longer in sync with the actual connection state.
- Now that DECNET is gone, we don't need to reserve space for DECNET
related information.
- compact common 'find a free port number for the new inbound
connection' code and move it to a helper, then cap number of tries
the new helper will make until it gives up.
- replace various instances of strlcpy with strscpy, from Wolfram Sang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Almost all nat helpers reserve an expecation port the same way:
Try the port inidcated by the peer, then move to next port if that
port is already in use.
We can squash this into a helper.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
As Eric reported, the 'reason' field is not presented when trace the
kfree_skb event by perf:
$ perf record -e skb:kfree_skb -a sleep 10
$ perf script
ip_defrag 14605 [021] 221.614303: skb:kfree_skb:
skbaddr=0xffff9d2851242700 protocol=34525 location=0xffffffffa39346b1
reason:
The cause seems to be passing kernel address directly to TP_printk(),
which is not right. As the enum 'skb_drop_reason' is not exported to
user space through TRACE_DEFINE_ENUM(), perf can't get the drop reason
string from the 'reason' field, which is a number.
Therefore, we introduce the macro DEFINE_DROP_REASON(), which is used
to define the trace enum by TRACE_DEFINE_ENUM(). With the help of
DEFINE_DROP_REASON(), now we can remove the auto-generate that we
introduced in the commit ec43908dd5
("net: skb: use auto-generation to convert skb drop reason to string"),
and define the string array 'drop_reasons'.
Hmmmm...now we come back to the situation that have to maintain drop
reasons in both enum skb_drop_reason and DEFINE_DROP_REASON. But they
are both in dropreason.h, which makes it easier.
After this commit, now the format of kfree_skb is like this:
$ cat /tracing/events/skb/kfree_skb/format
name: kfree_skb
ID: 1524
format:
field:unsigned short common_type; offset:0; size:2; signed:0;
field:unsigned char common_flags; offset:2; size:1; signed:0;
field:unsigned char common_preempt_count; offset:3; size:1; signed:0;
field:int common_pid; offset:4; size:4; signed:1;
field:void * skbaddr; offset:8; size:8; signed:0;
field:void * location; offset:16; size:8; signed:0;
field:unsigned short protocol; offset:24; size:2; signed:0;
field:enum skb_drop_reason reason; offset:28; size:4; signed:0;
print fmt: "skbaddr=%p protocol=%u location=%p reason: %s", REC->skbaddr, REC->protocol, REC->location, __print_symbolic(REC->reason, { 1, "NOT_SPECIFIED" }, { 2, "NO_SOCKET" } ......
Fixes: ec43908dd5 ("net: skb: use auto-generation to convert skb drop reason to string")
Link: https://lore.kernel.org/netdev/CANn89i+bx0ybvE55iMYf5GJM48WwV1HNpdm9Q6t-HaEstqpCSA@mail.gmail.com/
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move some MACsec infrastructure like defines and functions,
in order to avoid code duplication for future drivers which
implements MACsec offload.
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ben Ben-Ishay <benishay@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current MACsec offload implementation, MACsec interfaces shares
the same MAC address by default.
Therefore, HW can't distinguish from which MACsec interface the traffic
originated from.
MACsec stack will use skb_metadata_dst to store the SCI value, which is
unique per Macsec interface, skb_metadat_dst will be used by the
offloading device driver to associate the SKB with the corresponding
offloaded interface (SCI).
Signed-off-by: Lior Nahmanson <liorna@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink allows to specify allowed ranges for integer types.
Unfortunately, nfnetlink passes integers in big endian, so the existing
NLA_POLICY_MAX() cannot be used.
At the moment, nfnetlink users, such as nf_tables, need to resort to
programmatic checking via helpers such as nft_parse_u32_check().
This is both cumbersome and error prone. This adds NLA_POLICY_MAX_BE
which adds range check support for BE16, BE32 and BE64 integers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-09-05
The following pull-request contains BPF updates for your *net-next* tree.
We've added 106 non-merge commits during the last 18 day(s) which contain
a total of 159 files changed, 5225 insertions(+), 1358 deletions(-).
There are two small merge conflicts, resolve them as follows:
1) tools/testing/selftests/bpf/DENYLIST.s390x
Commit 27e23836ce ("selftests/bpf: Add lru_bug to s390x deny list") in
bpf tree was needed to get BPF CI green on s390x, but it conflicted with
newly added tests on bpf-next. Resolve by adding both hunks, result:
[...]
lru_bug # prog 'printk': failed to auto-attach: -524
setget_sockopt # attach unexpected error: -524 (trampoline)
cb_refs # expected error message unexpected error: -524 (trampoline)
cgroup_hierarchical_stats # JIT does not support calling kernel function (kfunc)
htab_update # failed to attach: ERROR: strerror_r(-524)=22 (trampoline)
[...]
2) net/core/filter.c
Commit 1227c1771d ("net: Fix data-races around sysctl_[rw]mem_(max|default).")
from net tree conflicts with commit 29003875bd ("bpf: Change bpf_setsockopt(SOL_SOCKET)
to reuse sk_setsockopt()") from bpf-next tree. Take the code as it is from
bpf-next tree, result:
[...]
if (getopt) {
if (optname == SO_BINDTODEVICE)
return -EINVAL;
return sk_getsockopt(sk, SOL_SOCKET, optname,
KERNEL_SOCKPTR(optval),
KERNEL_SOCKPTR(optlen));
}
return sk_setsockopt(sk, SOL_SOCKET, optname,
KERNEL_SOCKPTR(optval), *optlen);
[...]
The main changes are:
1) Add any-context BPF specific memory allocator which is useful in particular for BPF
tracing with bonus of performance equal to full prealloc, from Alexei Starovoitov.
2) Big batch to remove duplicated code from bpf_{get,set}sockopt() helpers as an effort
to reuse the existing core socket code as much as possible, from Martin KaFai Lau.
3) Extend BPF flow dissector for BPF programs to just augment the in-kernel dissector
with custom logic. In other words, allow for partial replacement, from Shmulik Ladkani.
4) Add a new cgroup iterator to BPF with different traversal options, from Hao Luo.
5) Support for BPF to collect hierarchical cgroup statistics efficiently through BPF
integration with the rstat framework, from Yosry Ahmed.
6) Support bpf_{g,s}et_retval() under more BPF cgroup hooks, from Stanislav Fomichev.
7) BPF hash table and local storages fixes under fully preemptible kernel, from Hou Tao.
8) Add various improvements to BPF selftests and libbpf for compilation with gcc BPF
backend, from James Hilliard.
9) Fix verifier helper permissions and reference state management for synchronous
callbacks, from Kumar Kartikeya Dwivedi.
10) Add support for BPF selftest's xskxceiver to also be used against real devices that
support MAC loopback, from Maciej Fijalkowski.
11) Various fixes to the bpf-helpers(7) man page generation script, from Quentin Monnet.
12) Document BPF verifier's tnum_in(tnum_range(), ...) gotchas, from Shung-Hsi Yu.
13) Various minor misc improvements all over the place.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (106 commits)
bpf: Optimize rcu_barrier usage between hash map and bpf_mem_alloc.
bpf: Remove usage of kmem_cache from bpf_mem_cache.
bpf: Remove prealloc-only restriction for sleepable bpf programs.
bpf: Prepare bpf_mem_alloc to be used by sleepable bpf programs.
bpf: Remove tracing program restriction on map types
bpf: Convert percpu hash map to per-cpu bpf_mem_alloc.
bpf: Add percpu allocation support to bpf_mem_alloc.
bpf: Batch call_rcu callbacks instead of SLAB_TYPESAFE_BY_RCU.
bpf: Adjust low/high watermarks in bpf_mem_cache
bpf: Optimize call_rcu in non-preallocated hash map.
bpf: Optimize element count in non-preallocated hash map.
bpf: Relax the requirement to use preallocated hash maps in tracing progs.
samples/bpf: Reduce syscall overhead in map_perf_test.
selftests/bpf: Improve test coverage of test_maps
bpf: Convert hash map to bpf_mem_alloc.
bpf: Introduce any context BPF specific memory allocator.
selftest/bpf: Add test for bpf_getsockopt()
bpf: Change bpf_getsockopt(SOL_IPV6) to reuse do_ipv6_getsockopt()
bpf: Change bpf_getsockopt(SOL_IP) to reuse do_ip_getsockopt()
bpf: Change bpf_getsockopt(SOL_TCP) to reuse do_tcp_getsockopt()
...
====================
Link: https://lore.kernel.org/r/20220905161136.9150-1-daniel@iogearbox.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch changes bpf_getsockopt(SOL_IPV6) to reuse
do_ipv6_getsockopt(). It removes the duplicated code from
bpf_getsockopt(SOL_IPV6).
This also makes bpf_getsockopt(SOL_IPV6) supporting the same
set of optnames as in bpf_setsockopt(SOL_IPV6). In particular,
this adds IPV6_AUTOFLOWLABEL support to bpf_getsockopt(SOL_IPV6).
ipv6 could be compiled as a module. Like how other code solved it
with stubs in ipv6_stubs.h, this patch adds the do_ipv6_getsockopt
to the ipv6_bpf_stub.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20220902002931.2896218-1-kafai@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch changes bpf_getsockopt(SOL_TCP) to reuse
do_tcp_getsockopt(). It removes the duplicated code from
bpf_getsockopt(SOL_TCP).
Before this patch, there were some optnames available to
bpf_setsockopt(SOL_TCP) but missing in bpf_getsockopt(SOL_TCP).
For example, TCP_NODELAY, TCP_MAXSEG, TCP_KEEPIDLE, TCP_KEEPINTVL,
and a few more. It surprises users from time to time. This patch
automatically closes this gap without duplicating more code.
bpf_getsockopt(TCP_SAVED_SYN) does not free the saved_syn,
so it stays in sol_tcp_sockopt().
For string name value like TCP_CONGESTION, bpf expects it
is always null terminated, so sol_tcp_sockopt() decrements
optlen by one before calling do_tcp_getsockopt() and
the 'if (optlen < saved_optlen) memset(..,0,..);'
in __bpf_getsockopt() will always do a null termination.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20220902002918.2894511-1-kafai@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch changes bpf_getsockopt(SOL_SOCKET) to reuse
sk_getsockopt(). It removes all duplicated code from
bpf_getsockopt(SOL_SOCKET).
Before this patch, there were some optnames available to
bpf_setsockopt(SOL_SOCKET) but missing in bpf_getsockopt(SOL_SOCKET).
It surprises users from time to time. For example, SO_REUSEADDR,
SO_KEEPALIVE, SO_RCVLOWAT, and SO_MAX_PACING_RATE. This patch
automatically closes this gap without duplicating more code.
The only exception is SO_BINDTODEVICE because it needs to acquire a
blocking lock. Thus, SO_BINDTODEVICE is not supported.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20220902002912.2894040-1-kafai@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Similar to the earlier patch that changes sk_getsockopt() to
take the sockptr_t argument . This patch also changes
do_ipv6_getsockopt() to take the sockptr_t argument such that
a latter patch can make bpf_getsockopt(SOL_IPV6) to reuse
do_ipv6_getsockopt().
Note on the change in ip6_mc_msfget(). This function is to
return an array of sockaddr_storage in optval. This function
is shared between ipv6_get_msfilter() and compat_ipv6_get_msfilter().
However, the sockaddr_storage is stored at different offset of the
optval because of the difference between group_filter and
compat_group_filter. Thus, a new 'ss_offset' argument is
added to ip6_mc_msfget().
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20220902002853.2892532-1-kafai@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When CONFIG_IEEE802154_NL802154_EXPERIMENTAL is disabled,
NL802154_CMD_DEL_SEC_LEVEL is undefined and results in a compilation
error:
net/ieee802154/nl802154.c:2503:19: error: 'NL802154_CMD_DEL_SEC_LEVEL' undeclared here (not in a function); did you mean 'NL802154_CMD_SET_CCA_ED_LEVEL'?
2503 | .resv_start_op = NL802154_CMD_DEL_SEC_LEVEL + 1,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| NL802154_CMD_SET_CCA_ED_LEVEL
Unhide the experimental commands, having them defined in an enum
makes no difference.
Fixes: 9c5d03d362 ("genetlink: start to validate reserved header bytes")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20220902030620.2737091-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal says:
====================
netfilter: bug fixes for net
1. Fix IP address check in irc DCC conntrack helper, this should check
the opposite direction rather than the destination address of the
packets' direction, from David Leadbeater.
2. bridge netfilter needs to drop dst references, from Harsh Modi.
This was fine back in the day the code was originally written,
but nowadays various tunnels can pre-set metadata dsts on packets.
3. Remove nf_conntrack_helper sysctl and the modparam toggle, users
need to explicitily assign the helpers to use via nftables or
iptables. Conntrack helpers, by design, may be used to add dynamic
port redirections to internal machines, so its necessary to restrict
which hosts/peers are allowed to use them.
It was discovered that improper checking in the irc DCC helper makes
it possible to trigger the 'please do dynamic port forward'
from outside by embedding a 'DCC' in a PING request; if the client
echos that back a expectation/port forward gets added.
The auto-assign-for-everything mechanism has been in "please don't do this"
territory since 2012. From Pablo.
4. Fix a memory leak in the netdev hook error unwind path, also from Pablo.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_conntrack_irc: Fix forged IP logic
netfilter: nf_tables: clean up hook list when offload flags check fails
netfilter: br_netfilter: Drop dst references before setting.
netfilter: remove nf_conntrack_helper sysctl and modparam toggles
====================
Link: https://lore.kernel.org/r/20220901071238.3044-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Howells says:
====================
rxrpc fixes
Here are some fixes for AF_RXRPC:
(1) Fix the handling of ICMP/ICMP6 packets. This is a problem due to
rxrpc being switched to acting as a UDP tunnel, thereby allowing it to
steal the packets before they go through the UDP Rx queue. UDP
tunnels can't get ICMP/ICMP6 packets, however. This patch adds an
additional encap hook so that they can.
(2) Fix the encryption routines in rxkad to handle packets that have more
than three parts correctly. The problem is that ->nr_frags doesn't
count the initial fragment, so the sglist ends up too short.
(3) Fix a problem with destruction of the local endpoint potentially
getting repeated.
(4) Fix the calculation of the time at which to resend.
jiffies_to_usecs() gives microseconds, not nanoseconds.
(5) Fix AFS to work out when callback promises and locks expire based on
the time an op was issued rather than the time the first reply packet
arrives. We don't know how long the server took between calculating
the expiry interval and transmitting the reply.
(6) Given (5), rxrpc_get_reply_time() is no longer used, so remove it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rxrpc_get_reply_time() as that is no longer used now that the call
issue time is used instead of the reply time.
Signed-off-by: David Howells <dhowells@redhat.com>
Because rxrpc pretends to be a tunnel on top of a UDP/UDP6 socket, allowing
it to siphon off UDP packets early in the handling of received UDP packets
thereby avoiding the packet going through the UDP receive queue, it doesn't
get ICMP packets through the UDP ->sk_error_report() callback. In fact, it
doesn't appear that there's any usable option for getting hold of ICMP
packets.
Fix this by adding a new UDP encap hook to distribute error messages for
UDP tunnels. If the hook is set, then the tunnel driver will be able to
see ICMP packets. The hook provides the offset into the packet of the UDP
header of the original packet that caused the notification.
An alternative would be to call the ->error_handler() hook - but that
requires that the skbuff be cloned (as ip_icmp_error() or ipv6_cmp_error()
do, though isn't really necessary or desirable in rxrpc's case is we want
to parse them there and then, not queue them).
Changes
=======
ver #3)
- Fixed an uninitialised variable.
ver #2)
- Fixed some missing CONFIG_AF_RXRPC_IPV6 conditionals.
Fixes: 5271953cad ("rxrpc: Use the UDP encap_rcv hook")
Signed-off-by: David Howells <dhowells@redhat.com>
Because per host rate limiting has been proven problematic (side channel
attacks can be based on it), per host rate limiting of challenge acks ideally
should be per netns and turned off by default.
This is a long due followup of following commits:
083ae30828 ("tcp: enable per-socket rate limiting of all 'challenge acks'")
f2b2c582e8 ("tcp: mitigate ACK loops for connections as tcp_sock")
75ff39ccc1 ("tcp: make challenge acks less predictable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason Baron <jbaron@akamai.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable "other" in the struct red_stats is not used. Remove it.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
__nf_ct_try_assign_helper() remains in place but it now requires a
template to configure the helper.
A toggle to disable automatic helper assignment was added by:
a900689264 ("netfilter: nf_ct_helper: allow to disable automatic helper assignment")
in 2012 to address the issues described in "Secure use of iptables and
connection tracking helpers". Automatic conntrack helper assignment was
disabled by:
3bb398d925 ("netfilter: nf_ct_helper: disable automatic helper assignment")
back in 2016.
This patch removes the sysctl and modparam toggles, users now have to
rely on explicit conntrack helper configuration via ruleset.
Update tools/testing/selftests/netfilter/nft_conntrack_helper.sh to
check that auto-assignment does not happen anymore.
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Follow-up the removal of unused internal api of port params made by
commit 42ded61aa7 ("devlink: Delete not used port parameters APIs")
and stub the commands and add extack message to tell the user what is
going on.
If later on port params are needed, could be easily re-introduced,
but until then it is a dead code.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220826082730.1399735-1-jiri@resnulli.us
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Being able to check attribute presence and set extack
if not on one line is handy, add helpers.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We had historically not checked that genlmsghdr.reserved
is 0 on input which prevents us from using those precious
bytes in the future.
One use case would be to extend the cmd field, which is
currently just 8 bits wide and 256 is not a lot of commands
for some core families.
To make sure that new families do the right thing by default
put the onus of opting out of validation on existing families.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com> (NetLabel)
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel borkmann says:
====================
The following pull-request contains BPF updates for your *net* tree.
We've added 11 non-merge commits during the last 14 day(s) which contain
a total of 13 files changed, 61 insertions(+), 24 deletions(-).
The main changes are:
1) Fix BPF verifier's precision tracking around BPF ring buffer, from Kumar Kartikeya Dwivedi.
2) Fix regression in tunnel key infra when passing FLOWI_FLAG_ANYSRC, from Eyal Birger.
3) Fix insufficient permissions for bpf_sys_bpf() helper, from YiFei Zhu.
4) Fix splat from hitting BUG when purging effective cgroup programs, from Pu Lehui.
5) Fix range tracking for array poke descriptors, from Daniel Borkmann.
6) Fix corrupted packets for XDP_SHARED_UMEM in aligned mode, from Magnus Karlsson.
7) Fix NULL pointer splat in BPF sockmap sk_msg_recvmsg(), from Liu Jian.
8) Add READ_ONCE() to bpf_jit_limit when reading from sysctl, from Kuniyuki Iwashima.
9) Add BPF selftest lru_bug check to s390x deny list, from Daniel Müller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory allocated by using kzallloc_node and kcalloc has been cleared.
Therefore, the structure members of the new qdisc are 0. So there's no
need to explicitly assign a value of 0.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes berg says:
====================
Various updates:
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit the acceptance of component name passed to cmd_flash_update() to
match one of the versions returned by info_get(), marked by version type.
This makes things clearer and enforces 1:1 mapping between exposed
version and accepted flash component.
Check VERSION_TYPE_COMPONENT version type during cmd_flash_update()
execution by calling info_get() with different "req" context.
That causes info_get() to lookup the component name instead of
filling-up the netlink message.
Remove "UPDATE_COMPONENT" flag which becomes used.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Whenever the driver is called by his info_get() op, it may put multiple
version names and values to the netlink message. Extend by additional
helper devlink_info_version_running/stored_put_ext() that allows to
specify a version type that indicates when particular version name
represents a flash component.
This is going to be used in follow-up patch calling info_get() during
flash update command checking if version with this the version type
exists.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To helper drivers if they e.g. have a lookup of the link_sta
pointer, add the link ID to the link_sta structure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, when the address translation from link to MLD is done
in fw/hw, it is necessary to be able to have some information
on the link on which the frame has been received. Extend the
rx API to include link_id and a valid flag in ieee80211_rx_status.
Also make chanes to mac80211 rx APIs to make use of the reported
link_id after sanity checks.
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Link: https://lore.kernel.org/r/20220817104213.2531-2-quic_vthiagar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement key installation and lookup (on TX and RX)
for MLO, so we can use multiple GTKs/IGTKs/BIGTKs.
Co-authored-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for various key operations on MLD by adding new parameter
link_id. Pass the link_id received from userspace to driver for add_key,
get_key, del_key, set_default_key, set_default_mgmt_key and
set_default_beacon_key to support configuring keys specific to each MLO
link. Userspace must not specify link ID for MLO pairwise key since it
is common for all the MLO links.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20220730052643.1959111-4-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Tx queue parameters are per link, so add the link ID
from nl80211 parameters to the API.
While at it, lock the wdev when calling into the driver
so it (and we) can check the link ID appropriately.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce a simple helper function to replace a common pattern.
When accessing the GRO header, we fetch the pointer from frag0,
then test its validity and fetch it from the skb when necessary.
This leads to the pattern
skb_gro_header_fast -> skb_gro_header_hard -> skb_gro_header_slow
recurring many times throughout GRO code.
This patch replaces these patterns with a single inlined function
call, improving code readability.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220823071034.GA56142@debian
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The current bind hashtable (bhash) is hashed by port only.
In the socket bind path, we have to check for bind conflicts by
traversing the specified port's inet_bind_bucket while holding the
hashbucket's spinlock (see inet_csk_get_port() and
inet_csk_bind_conflict()). In instances where there are tons of
sockets hashed to the same port at different addresses, the bind
conflict check is time-intensive and can cause softirq cpu lockups,
as well as stops new tcp connections since __inet_inherit_port()
also contests for the spinlock.
This patch adds a second bind table, bhash2, that hashes by
port and sk->sk_rcv_saddr (ipv4) and sk->sk_v6_rcv_saddr (ipv6).
Searching the bhash2 table leads to significantly faster conflict
resolution and less time holding the hashbucket spinlock.
Please note a few things:
* There can be the case where the a socket's address changes after it
has been bound. There are two cases where this happens:
1) The case where there is a bind() call on INADDR_ANY (ipv4) or
IPV6_ADDR_ANY (ipv6) and then a connect() call. The kernel will
assign the socket an address when it handles the connect()
2) In inet_sk_reselect_saddr(), which is called when rebuilding the
sk header and a few pre-conditions are met (eg rerouting fails).
In these two cases, we need to update the bhash2 table by removing the
entry for the old address, and add a new entry reflecting the updated
address.
* The bhash2 table must have its own lock, even though concurrent
accesses on the same port are protected by the bhash lock. Bhash2 must
have its own lock to protect against cases where sockets on different
ports hash to different bhash hashbuckets but to the same bhash2
hashbucket.
This brings up a few stipulations:
1) When acquiring both the bhash and the bhash2 lock, the bhash2 lock
will always be acquired after the bhash lock and released before the
bhash lock is released.
2) There are no nested bhash2 hashbucket locks. A bhash2 lock is always
acquired+released before another bhash2 lock is acquired+released.
* The bhash table cannot be superseded by the bhash2 table because for
bind requests on INADDR_ANY (ipv4) or IPV6_ADDR_ANY (ipv6), every socket
bound to that port must be checked for a potential conflict. The bhash
table is the only source of port->socket associations.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Fix crash with malformed ebtables blob which do not provide all
entry points, from Florian Westphal.
2) Fix possible TCP connection clogging up with default 5-days
timeout in conntrack, from Florian.
3) Fix crash in nf_tables tproxy with unsupported chains, also from Florian.
4) Do not allow to update implicit chains.
5) Make table handle allocation per-netns to fix data race.
6) Do not truncated payload length and offset, and checksum offset.
Instead report EINVAl.
7) Enable chain stats update via static key iff no error occurs.
8) Restrict osf expression to ip, ip6 and inet families.
9) Restrict tunnel expression to netdev family.
10) Fix crash when trying to bind again an already bound chain.
11) Flowtable garbage collector might leave behind pending work to
delete entries. This patch comes with a previous preparation patch
as dependency.
12) Allow net.netfilter.nf_conntrack_frag6_high_thresh to be lowered,
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_defrag_ipv6: allow nf_conntrack_frag6_high_thresh increases
netfilter: flowtable: fix stuck flows on cleanup due to pending work
netfilter: flowtable: add function to invoke garbage collection immediately
netfilter: nf_tables: disallow binding to already bound chain
netfilter: nft_tunnel: restrict it to netdev family
netfilter: nft_osf: restrict osf to ipv4, ipv6 and inet families
netfilter: nf_tables: do not leave chain stats enabled on error
netfilter: nft_payload: do not truncate csum_offset and csum_type
netfilter: nft_payload: report ERANGE for too long offset and length
netfilter: nf_tables: make table handle allocation per-netns friendly
netfilter: nf_tables: disallow updates of implicit chain
netfilter: nft_tproxy: restrict to prerouting hook
netfilter: conntrack: work around exceeded receive window
netfilter: ebtables: reject blobs that don't provide all entry points
====================
Link: https://lore.kernel.org/r/20220824220330.64283-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While reading gro_normal_batch, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL skbs")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
