Pull char/misc driver fixes from Greg KH:
"Here are three small driver fixes for reported issues for 3.19-rc5.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mcb: mcb-pci: Only remap the 1st 0x200 bytes of BAR 0
mei: add ABI documentation for fw_status exported through sysfs
mei: clean reset bit before reset
Pull driver core fix from Greg KH:
"Here is one kernfs fix for a reported issue for 3.19-rc5.
It has been in linux-next for a while"
* tag 'driver-core-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: Fix kernfs_name_compare
Pull tty/serial driver fixes from Greg KH:
"Here are some tty and serial driver fixes for 3.19-rc5 that resolve
some reported issues, and add a new device id to the 8250 serial port
driver.
All have been in linux-next with no reported problems"
* tag 'tty-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: samsung: Add the support for Exynos5433 SoC
Revert "tty: Fix pty master poll() after slave closes v2"
tty: Prevent hw state corruption in exclusive mode reopen
tty: Add support for the WCH384 4S multi-IO card
serial: fix parisc boot hang
Pull staging driver fixes from Greg KH:
"Here are 6 staging driver fixes for 3.19-rc5.
They fix some reported issues with some IIO drivers, as well as some
issues with the vt6655 wireless driver.
All have been in linux-next for a while"
* tag 'staging-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: fix sparse warning: argument type
staging: vt6655: Fix loss of distant/weak access points on channel change.
staging: vt6655: vnt_tx_packet Fix corrupted tx packets.
staging: vt6655: fix sparse warnings: incorrect argument type
iio: iio: Fix iio_channel_read return if channel havn't info
iio: ad799x: Fix ad7991/ad7995/ad7999 config setup
Pull USB fixes from Greg KH:
"Here is a bunch of USB fixes for 3.19-rc5.
Most of these are gadget driver fixes, along with the xhci driver fix
that we both reported having problems with, as well as some new device
ids and other tiny fixes.
All have been in linux-next with no problems"
* tag 'usb-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
usb: dwc3: gadget: Stop TRB preparation after limit is reached
usb: dwc3: gadget: Fix TRB preparation during SG
usb: phy: mv-usb: fix usb_phy build errors
usb: serial: handle -ENODEV quietly in generic_submit_read_urb
usb: serial: silence all non-critical read errors
USB: console: fix potential use after free
USB: console: fix uninitialised ldisc semaphore
usb: gadget: udc: atmel: fix possible oops when unloading module
usb: gadget: gadgetfs: fix an oops in ep_write()
usb: phy: Fix deferred probing
OHCI: add a quirk for ULi M5237 blocking on reset
uas: Add US_FL_NO_ATA_1X for 2 more Seagate disk enclosures
uas: Do not blacklist ASM1153 disk enclosures
usb: gadget: udc: avoid dereference before NULL check in ep_queue
usb: host: ehci-tegra: request deferred probe when failing to get phy
uas: disable UAS on Apricorn SATA dongles
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS566 with usb-id 0bc2:a013
uas: Add US_FL_NO_ATA_1X for Seagate devices with usb-id 0bc2:a013
xhci: Add broken-streams quirk for Fresco Logic FL1000G xhci controllers
USB: EHCI: adjust error return code
...
Pull arm64 fixes from Will Deacon:
- Wire up compat_sys_execveat for compat (AArch32) tasks
- Revert 421520ba98, as this breaks our side of the boot protocol
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: partially revert "ARM: 8167/1: extend the reserved memory for initrd to be page aligned"
arm64: compat: wire up compat_sys_execveat
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Stable fix for a NFSv3/lockd race
- Fixes for several NFSv4.1 client id trunking bugs
- Remove an incorrect test when checking for delegated opens"
* tag 'nfs-for-3.19-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Remove incorrect check in can_open_delegated()
NFS: Ignore transport protocol when detecting server trunking
NFSv4/v4.1: Verify the client owner id during trunking detection
NFSv4: Cache the NFSv4/v4.1 client owner_id in the struct nfs_client
NFSv4.1: Fix client id trunking on Linux
LOCKD: Fix a race when initialising nlmsvc_timeout
Pull ftrace fixes from Steven Rostedt:
"This holds a few fixes to the ftrace infrastructure as well as the
mixture of function graph tracing and kprobes.
When jprobes and function graph tracing is enabled at the same time it
will crash the system:
# modprobe jprobe_example
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
After the first fork (jprobe_example probes it), the system will
crash.
This is due to the way jprobes copies the stack frame and does not do
a normal function return. This messes up with the function graph
tracing accounting which hijacks the return address from the stack and
replaces it with a hook function. It saves the return addresses in a
separate stack to put back the correct return address when done. But
because the jprobe functions do not do a normal return, their stack
addresses are not put back until the function they probe is called,
which means that the probed function will get the return address of
the jprobe handler instead of its own.
The simple fix here was to disable function graph tracing while the
jprobe handler is being called.
While debugging this I found two minor bugs with the function graph
tracing.
The first was about the function graph tracer sharing its function
hash with the function tracer (they both get filtered by the same
input). The changing of the set_ftrace_filter would not sync the
function recording records after a change if the function tracer was
disabled but the function graph tracer was enabled. This was due to
the update only checking one of the ops instead of the shared ops to
see if they were enabled and should perform the sync. This caused the
ftrace accounting to break and a ftrace_bug() would be triggered,
disabling ftrace until a reboot.
The second was that the check to update records only checked one of
the filter hashes. It needs to test both the "filter" and "notrace"
hashes. The "filter" hash determines what functions to trace where as
the "notrace" hash determines what functions not to trace (trace all
but these). Both hashes need to be passed to the update code to find
out what change is being done during the update. This also broke the
ftrace record accounting and triggered a ftrace_bug().
This patch set also include two more fixes that were reported
separately from the kprobe issue.
One was that init_ftrace_syscalls() was called twice at boot up. This
is not a major bug, but that call performed a rather large kmalloc
(NR_syscalls * sizeof(*syscalls_metadata)). The second call made the
first one a memory leak, and wastes memory.
The other fix is a regression caused by an update in the v3.19 merge
window. The moving to enable events early, moved the enabling before
PID 1 was created. The syscall events require setting the
TIF_SYSCALL_TRACEPOINT for all tasks. But for_each_process_thread()
does not include the swapper task (PID 0), and ended up being a nop.
A suggested fix was to add the init_task() to have its flag set, but I
didn't really want to mess with PID 0 for this minor bug. Instead I
disable and re-enable events again at early_initcall() where it use to
be enabled. This also handles any other event that might have its own
reg function that could break at early boot up"
* tag 'trace-fixes-v3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix enabling of syscall events on the command line
tracing: Remove extra call to init_ftrace_syscalls()
ftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing
ftrace: Check both notrace and filter for old hash
ftrace: Fix updating of filters for shared global_ops filters
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: "James E.J. Bottomley" <jejb@parisc-linux.org>
CC: Helge Deller <deller@gmx.de>
CC: linux-parisc@vger.kernel.org
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Michal Simek <monstr@monstr.eu>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: David Howells <dhowells@redhat.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
Add pci_claim_bridge_resource() to claim a PCI-PCI bridge window. This is
like regular pci_claim_resource(), except that if we fail to claim the
window, we check to see if we can reduce the size of the window and try
again.
This is for scenarios like this:
pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff]
pci 0000:00:01.0: bridge window [mem 0xbdf00000-0xddefffff 64bit pref]
pci 0000:01:00.0: reg 0x10: [mem 0xc0000000-0xcfffffff pref]
The 00:01.0 window is illegal: it starts before the host bridge window, so
we have to assume the [0xbdf00000-0xbfffffff] region is inaccessible. We
can make it legal by clipping it to [mem 0xc0000000-0xddefffff 64bit pref].
Previously we discarded the 00:01.0 window and tried to reassign that part
of the hierarchy from scratch. That is a problem because Linux doesn't
always assign things optimally. For example, in this case, BIOS put the
01:00.0 device in a prefetchable window below 4GB, but after 5b28541552,
Linux puts the prefetchable window above 4GB where the 32-bit 01:00.0
device can't use it.
Clipping the 00:01.0 window is less intrusive than completely reassigning
things and is sufficient to let us use most of the BIOS configuration. Of
course, it's possible that devices below 00:01.0 will no longer fit. If
that's the case, we'll have to reassign things. But that's a separate
problem.
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
Add pci_bus_clip_resource(). If a PCI-PCI bridge window overlaps an
upstream bridge window but is not completely contained by it, this clips
the downstream window so it fits inside the upstream one.
No functional change (this adds the function but no callers).
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
pci_setup_bridge_io(), pci_setup_bridge_mmio(), and
pci_setup_bridge_mmio_pref() program the windows of PCI-PCI bridges.
Previously they accepted a pointer to the pci_bus of the secondary bus,
then looked up the bridge leading to that bus. Pass the bridge directly,
which will make it more convenient for future callers.
No functional change.
[bhelgaas: changelog, split into separate patch]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.16+
Reports against the TL-WDN4800 card indicate that PCI bus reset of this
Atheros device cause system lock-ups and resets. I've also been able to
confirm this behavior on multiple systems. The device never returns from
reset and attempts to access config space of the device after reset result
in hangs. Blacklist bus reset for the device to avoid this issue.
[bhelgaas: This regression appeared in v3.14. Andreas bisected it to
425c1b223d ("PCI: Add Virtual Channel to save/restore support"), but we
don't understand the mechanism by which that commit affects the reset
path.]
[bhelgaas: changelog, references]
Link: http://lkml.kernel.org/r/20140923210318.498dacbd@dualc.maya.org
Reported-by: Andreas Hartmann <andihartmann@freenet.de>
Tested-by: Andreas Hartmann <andihartmann@freenet.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
Enable a mechanism for devices to quirk that they do not behave when
doing a PCI bus reset. We require a modest level of spec compliant
behavior in order to do a reset, for instance the device should come
out of reset without throwing errors and PCI config space should be
accessible after reset. This is too much to ask for some devices.
Link: http://lkml.kernel.org/r/20140923210318.498dacbd@dualc.maya.org
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
This patch partially reverts commit 421520ba98
(only the arm64 part). There is no guarantee that the boot-loader places other
images like dtb in a different page than initrd start/end, especially when the
kernel is built with 64KB pages. When this happens, such pages must not be
freed. The free_reserved_area() already takes care of rounding up "start" and
rounding down "end" to avoid freeing partially used pages.
Cc: <stable@vger.kernel.org> # 3.17+
Reported-by: Peter Maydell <Peter.Maydell@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If the irq_chip does not define .irq_disable, any call to disable_irq
will defer disabling the IRQ until it fires while marked as disabled.
This assumes that the handler function checks for this condition, which
handle_percpu_irq does not. In this case, calling disable_irq leads to
an IRQ storm, if the interrupt fires while disabled.
This optimization is only useful when disabling the IRQ is slow, which
is not true for the MIPS CPU IRQ.
Disable this optimization by implementing .irq_disable and .irq_enable
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8949/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This commit adds support for multiple hardware chip selects to spi-orion.
Different SoCs support different number of chip selects (up to
8 on some platforms). The driver allows up to this number, and it is up
to the implementer to only use the chip selects that are available.
Signed-off-by: Ken Wilson <ken.wilson@opengear.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 18743d2781 ("irqchip: mips-gic: Stop using per-platform mapping
tables") in v3.19-rc1 changed the routing of IPIs through the GIC to go
to the HW0 IRQ pin along with the rest of the GIC interrupts, rather
than to HW1 and HW2 pins.
This breaks SMP boot using the CMP or MT SMP implementations because HW0
doesn't get unmasked when secondary CPUs are initialised so the IPIs
will never interrupt secondary CPUs (nor any other interrupts routed
through the GIC).
Commit ff1e29ade4 ("MIPS: smp-cps: Enable all hardware interrupts on
secondary CPUs") fixed this in advance for the CPS SMP implementation by
unmasking all hardware interrupt lines for secondary CPUs, so lets do
the same for the CMP and MT implementations.
Fixes: 18743d2781 ("irqchip: mips-gic: Stop using per-platform mapping tables")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9025/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cycles:p and cycles:pp do not work on SLM since commit:
86a04461a9 ("perf/x86: Revamp PEBS event selection")
UOPS_RETIRED.ALL is not a PEBS capable event, so it should not be used
to count cycle number.
Actually SLM calls intel_pebs_aliases_core2() which uses INST_RETIRED.ANY_P
to count the number of cycles. It's a PEBS capable event. But inv and
cmask must be set to count cycles.
Considering SLM allows all events as PEBS with no flags, only
INST_RETIRED.ANY_P, inv=1, cmask=16 needs to handled specially.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1421084541-31639-1-git-send-email-kan.liang@intel.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch fixes a problem with the initialization of the
sysfs_show() routine for the RAPL PMU.
The current code was wrongly relying on the EVENT_ATTR_STR()
macro which uses the events_sysfs_show() function in the x86
PMU code. That function itself was relying on the x86_pmu data
structure. Yet RAPL and the core PMU (x86_pmu) have nothing to
do with each other. They should therefore not interact with
each other.
The x86_pmu structure is initialized at boot time based on
the host CPU model. When the host CPU is not supported, the
x86_pmu remains uninitialized and some of the callbacks it
contains are NULL.
The false dependency with x86_pmu could potentially cause crashes
in case the x86_pmu is not initialized while the RAPL PMU is. This
may, for instance, be the case in virtualized environments.
This patch fixes the problem by using a private sysfs_show()
routine for exporting the RAPL PMU events.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20150113225953.GA21525@thinkpad
Cc: vincent.weaver@maine.edu
Cc: jolsa@redhat.com
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The current tiny RCU stall-warning code assumes that the jiffies counter
starts at zero, however, it is sometimes initialized to other values,
for example, -30,000. This commit therefore changes rcu_init() to
invoke reset_cpu_stall_ticks() for both flavors of RCU to initialize
the stall-warning times properly at boot.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The tiny RCU CPU stall detection depends on *rcp->curtail not being
NULL. It is however a tail pointer and thus NULL by definition. Instead we
should check rcp->rcucblist for the presence of pending callbacks which
need to be processed. With this fix INFO about the stall is printed and
jiffies_stall (jiffies at next stall) correctly updated.
Note that the check for pending callback is necessary to avoid spurious
warnings if there are no pendings callbacks.
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
[ paulmck: Fused identical "if" statements, ported to -rcu. ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit adds a message that is printed if the relevant grace-period
kthread has not been able to run for the two seconds preceding the
stall warning. (The two seconds is double the maximum interval between
successive bouts of quiescent-state forcing.)
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Although cond_resched_rcu_qs() only applies to TASKS_RCU, it is used
in places where it would be useful for it to apply to the normal RCU
flavors, rcu_preempt, rcu_sched, and rcu_bh. This is especially the
case for workloads that aggressively overload the system, particularly
those that generate large numbers of RCU updates on systems running
NO_HZ_FULL CPUs. This commit therefore communicates quiescent states
from cond_resched_rcu_qs() to the normal RCU flavors.
Note that it is unfortunately necessary to leave the old ->passed_quiesce
mechanism in place to allow quiescent states that apply to only one
flavor to be recorded. (Yes, we could decrement ->rcu_qs_ctr_snap in
that case, but that is not so good for debugging of RCU internals.)
In addition, if one of the RCU flavor's grace period has stalled, this
will invoke rcu_momentary_dyntick_idle(), resulting in a heavy-weight
quiescent state visible from other CPUs.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: Merge commit from Sasha Levin fixing a bug where __this_cpu()
was used in preemptible code. ]
Recent testing has shown that under heavy load, running RCU's grace-period
kthreads at real-time priority can improve performance (according to 0day
test robot) and reduce the incidence of RCU CPU stall warnings. However,
most systems do just fine with the default non-realtime priorities for
these kthreads, and it does not make sense to expose the entire user
base to any risk stemming from this change, given that this change is
of use only to a few users running extremely heavy workloads.
Therefore, this commit allows users to specify realtime priorities
for the grace-period kthreads, but leaves them running SCHED_OTHER
by default. The realtime priority may be specified at build time
via the RCU_KTHREAD_PRIO Kconfig parameter, or at boot time via the
rcutree.kthread_prio parameter. Either way, 0 says to continue the
default SCHED_OTHER behavior and values from 1-99 specify that priority
of SCHED_FIFO behavior. Note that a value of 0 is not permitted when
the RCU_BOOST Kconfig parameter is specified.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
softnet_data.input_pkt_queue is protected by a spinlock that
we must hold when transferring packets from victim queue to an active
one. This is because other cpus could still be trying to enqueue packets
into victim queue.
A second problem is that when we transfert the NAPI poll_list from
victim to current cpu, we absolutely need to special case the percpu
backlog, because we do not want to add complex locking to protect
process_queue : Only owner cpu is allowed to manipulate it, unless cpu
is offline.
Based on initial patch from Prasad Sodagudi & Subash Abhinov
Kasiviswanathan.
This version is better because we do not slow down packet processing,
only make migration safer.
Reported-by: Prasad Sodagudi <psodagud@codeaurora.org>
Reported-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren says:
====================
Fixes for davinci_emac
Here's a repost of the fixes for davinci_emac with patches
updated for comments and acks collected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices like dm816x have the MDIO registers within the first EMAC
instance address space. Let's fix the issue by allowing to pass an
optional second IO range for the EMAC control register area.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like the phy_id is never set up beyond getting the phandle.
Note that we can remove the ifdef for phy_node as there is a stub
for of_phy_connec() if CONFIG_OF is not set.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only use clk_get() to get the frequency, the rest is done by
the runtime PM calls. Let's free the clock too.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ba9738134 ("net: ethernet: davinci_emac: add pm_runtime support")
added support for runtime PM, but it causes issues on omap3 related devices
that actually gate the clocks:
Unhandled fault: external abort on non-linefetch (0x1008)
...
[<c04160f0>] (emac_dev_getnetstats) from [<c04d6a3c>] (dev_get_stats+0x78/0xc8)
[<c04d6a3c>] (dev_get_stats) from [<c04e9ccc>] (rtnl_fill_ifinfo+0x3b8/0x938)
[<c04e9ccc>] (rtnl_fill_ifinfo) from [<c04eade4>] (rtmsg_ifinfo+0x68/0xd8)
[<c04eade4>] (rtmsg_ifinfo) from [<c04dd35c>] (register_netdevice+0x3a0/0x4ec)
[<c04dd35c>] (register_netdevice) from [<c04dd4bc>] (register_netdev+0x14/0x24)
[<c04dd4bc>] (register_netdev) from [<c041755c>] (davinci_emac_probe+0x408/0x5c8)
[<c041755c>] (davinci_emac_probe) from [<c0396d78>] (platform_drv_probe+0x48/0xa4)
Let's fix it by moving the pm_runtime_get() call earlier, and also add it to
the emac_dev_getnetstats(). Also note that we want to use pm_runtime_get_sync()
as we don't want to have deferred_resume happen. And let's also check the
return value for pm_runtime_get_sync() as noted by Felipe Balbi <balbi@ti.com>.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On davinci_emac, we have pulse interrupts. This means that we need to
clear the EOI bits when disabling interrupts as otherwise the interrupts
keep happening. And we also need to not clear the EOI bits again when
enabling the interrupts as otherwise we will get tons of:
unexpected IRQ trap at vector 00
These errors almost certainly mean that the omap-intc.c is signaling
a spurious interrupt with the reserved irq 127 as we've seen earlier
on omap3.
Let's fix the issue by clearing the EOI bits when disabling the
interrupts. Let's also keep the comment for "Rx Threshold and Misc
interrupts are not enabled" for both enable and disable so people
are aware of this when potentially adding more support.
Note that eventually we should handle the RX and TX interrupts
separately like cpsw is now doing. However, so far I have not seen
any issues with this based on my testing, so it seems to behave a
little different compared to the cpsw that had a similar issue.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fuse fixes from Miklos Szeredi:
"This fixes a regression in the latest fuse update plus a fix for a
rather theoretical memory ordering issue"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: add memory barrier to INIT
fuse: fix LOOKUP vs INIT compat handling
