This standard is not properly documented, but its settings are at
the tda18271dd driver, and are somewhat obvious, as they follow
the same logic as DVB-T 7MHz.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a bug on mxl5005s logic: when the bandwidth changes, but using
the same delivery system, the code discard the set_params()
reconfiguration request.
This was happening because, in the previous coding, the bandwidth
calculus were after the check for delivery system changes.
The previous patch changed the logic to estimate the bandwidth to
happend together with the changes at the delivery system.
So, with a one-statement change, it is possible to make the tuner to
reconfigure, in order to adjust to bandwidth changes. this will
likely fix issues on countries that use 7MHz/8MHz DVB-T channels.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver implements a fake get_bandwidth() callback. In
reallity, the tuner driver won't adjust its low-pass
filter based on a bandwidth, and were just providing a fake
method for demods to read whatever was "set".
This code is useless, as none of the drivers that use
this tuner seems to require a get_bandwidth() callback.
While here, convert set_params to use the DVBv5 way to pass
parameters to tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver implements a fake get_bandwidth() callback. In
reallity, the tuner driver won't adjust its low-pass
filter based on a bandwidth, and were just providing a fake
method for demods to read whatever was "set".
This code is useless, as none of the drivers that use
this tuner seems to require a get_bandwidth() callback.
While here, convert set_params to use the DVBv5 way to pass
parameters to tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver implements a fake get_bandwidth() callback. In
reallity, the tuner driver won't adjust its low-pass
filter based on a bandwidth, and were just providing a fake
method for demods to read whatever was "set".
This code is useless, as none of the drivers that use
this tuner seems to require a get_bandwidth() callback.
While here, convert set_params to use the DVBv5 way to pass
parameters to tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of just estimating the bandwidth for DVB-C annex A/C,
also fill it at the core for ATSC and DVB-C annex B. This
simplifies the logic inside the tuners, as all non-satellite
tuners can just use c->bandwidth_hz for all supported
delivery systems.
It could make sense to latter use it also for satellite
systems, as several DVB-S drivers have their own calculus.
However, on DVB-S2 the bw estimation is a little more complex,
and the existing drivers have some optimized calculus for
bandwidth. So, let's not touch on it for now.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SYS_DVBC_ANNEX_AC is an alias for SYS_DVBC_ANNEX_A. However,
the first one is incorrect, as not all devices support both.
So, replace its occurrences by the proper value (either
SYS_DVBC_ANNEX_A or both SYS_DVBC_ANNEX_A and SYS_DVBC_ANNEX_C).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restore skge hardware registers for multicast filtering to their
appropriate values after system resume and after hardware restarts
that are done when changing certain settings.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent suspend testing on !SMP build discovers that the __CPUINIT
annotation for v7_invalidate_l1 should not be there, as the function
is called by resume path for not only SMP but also !SMP build.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Several protocol initialization routines can fail after they set up
psmouse methods, such as reconnect and disconnect. This may lead to
these stale methods used with different protocol that they were
intended to be used for and may cause unpredictavle behavior and/or
crashes.
Make sure we start with a clean slate before executing each and every
protocol detection and/or initialization routine.
Reported-by: Paul Fox <pgf@laptop.org>
Acked-by: Tai-hwa Liang <avatar@sentelic.com>
Acked-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If there is a full packet in the buffer, and we overflow that buffer
right after checking for that condition, it would have been possible
for us to block indefinitely (rather, until the next full packet) even if
the file was marked as O_NONBLOCK.
Cc: Jeff Brown <jeffbrown@android.com>
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Without this, it was possible for the reader to get ahead of packet_head.
If the input device generated a partial packet *right* after the reader
got ahead, then we can get into a situation where the device is marked
readable, but read always returns 0 until the next packet is finished
(i.e a SYN is generated by the input driver).
This situation can also happen if we overflow the buffer while a reader
is trying to read an event out.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
be2net gets an async link status notification from the FW when it creates
an MCC queue. There are some cases in which this gratuitous notification
is not received from FW. To cover this explicitly query the link status
in be_open().
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) fix be_vlan_add/rem_vid to return proper status
2) perform appropriate housekeeping if firmware command succeeds.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 10f6dfcfde (Revert "sch_netem: Remove classful functionality")
reintroduced classful functionality to netem, but broke basic netem
behavior :
netem uses an t(ime)fifo queue, and store timestamps in skb->cb[]
If qdisc is changed, time constraints are not respected and other qdisc
can destroy skb->cb[] and block netem at dequeue time.
Fix this by always using internal tfifo, and optionally attach a child
qdisc to netem (or a tree of qdiscs)
Example of use :
DEV=eth3
tc qdisc del dev $DEV root
tc qdisc add dev $DEV root handle 30: est 1sec 8sec netem delay 20ms 10ms
tc qdisc add dev $DEV handle 40:0 parent 30:0 tbf \
burst 20480 limit 20480 mtu 1514 rate 32000bps
qdisc netem 30: root refcnt 18 limit 1000 delay 20.0ms 10.0ms
Sent 190792 bytes 413 pkt (dropped 0, overlimits 0 requeues 0)
rate 18416bit 3pps backlog 0b 0p requeues 0
qdisc tbf 40: parent 30: rate 256000bit burst 20Kb/8 mpu 0b lat 0us
Sent 190792 bytes 413 pkt (dropped 6, overlimits 10 requeues 0)
backlog 0b 5p requeues 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During some debugging I needed to look into how /proc/net/ipv6_route
operated and in my digging I found its calling fib6_clean_all() which uses
"write_lock_bh(&table->tb6_lock)" before doing the walk of the table. I
found this on 2.6.32, but reading the code I believe the same basic idea
exists currently. Looking at the rtnetlink code they are only calling
"read_lock_bh(&table->tb6_lock);" via fib6_dump_table(). While I realize
reading from proc isn't the recommended way of fetching the ipv6 route
table; taking a write lock seems unnecessary and would probably cause
network performance issues.
To verify this I loaded up the ipv6 route table and then ran iperf in 3
cases:
* doing nothing
* reading ipv6 route table via proc
(while :; do cat /proc/net/ipv6_route > /dev/null; done)
* reading ipv6 route table via rtnetlink
(while :; do ip -6 route show table all > /dev/null; done)
* Load the ipv6 route table up with:
* for ((i = 0;i < 4000;i++)); do ip route add unreachable 2000::$i; done
* iperf commands:
* client: iperf -i 1 -V -c <ipv6 addr>
* server: iperf -V -s
* iperf results - 3 runs each (in Mbits/sec)
* nothing: client: 927,927,927 server: 927,927,927
* proc: client: 179,97,96,113 server: 142,112,133
* iproute: client: 928,927,928 server: 927,927,927
lock_stat shows taking the write lock is causing the slowdown. Using this
info I decided to write a version of fib6_clean_all() which replaces
write_lock_bh(&table->tb6_lock) with read_lock_bh(&table->tb6_lock). With
this new function I see the same results as with my rtnetlink iperf test.
Signed-off-by: Josh Hunt <joshhunt00@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it's not too late fix the recently added RQLEN diag extension
to report rqlen and wqlen in the same way as TCP does.
I.e. for listening sockets the ack backlog length (which is the input
queue length for socket) in rqlen and the max ack backlog length in
wqlen, and what the CINQ/OUTQ ioctls do for established.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tcp diag reports rqlen and wqlen values similar to how
the CINQ/COUTQ iotcls do. To make unix diag report these values
in the same way move the respective code into helpers.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ Fix indentation of sock_diag*() calls. -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a routine that dumps memory-related values of a socket.
It's made as an array to make it possible to add more stuff
here later without breaking compatibility.
Since v1: The SK_MEMINFO_ constants are in userspace
visible part of sock_diag.h, the rest is under __KERNEL__.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The headers check complains it should include the linux/types.h
withing, thus add this one.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly toss existing components around the ifdef __KERNEL__
and include the header into the header-y target.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO_wdt.c - problems with newer hardware due to SMI clearing (part 2)
watchdog: hpwdt: Changes to handle NX secure bit in 32bit path
watchdog: sp805: Fix section mismatch in ID table.
watchdog: move coh901327 state holders
dvb_register calls videobuf_dvb_register_bus, but if that returns
a failure the module will be unloaded without clearing the
value of core->gate_ctrl which will cause an oops in macros
called from video_open in cx88-video.c
Signed-off-by: David Fries <David@Fries.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Istvan Varga <istvan_v@mailbox.hu>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stop dual frontend attach in warm state with single devices.
Since this is a no reconnect device this occurs only after a warm system
reboot.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Re: [git:v4l-dvb/for_v3.3] [media] it9135: add support for IT9135 9005 devices
On Sun, 2011-12-11 at 11:55 +0100, Mauro Carvalho Chehab wrote:
> This is an automatic generated email to let you know that the following patch were queued at the
> http://git.linuxtv.org/media_tree.git tree:
>
> Subject: [media] it9135: add support for IT9135 9005 devices
> Author: Malcolm Priestley <tvboxspy@gmail.com>
> Date: Wed Nov 30 17:16:09 2011 -0300
>
> Support add for IT9135 9005 devices
>
> With this patch IT9135 devices now move to using
> dvb-usb-it9135-01.fw firmware
> IT9137 remain on previous firmware.
Hi Mauro,
I have made a small mistake on this patch.
I forgot to increase number of num_device_descs to 4.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
