The hibernation mode of Atheros AR803x PHYs defaults to be
enabled after hardware reset. When the cable is unplugged,
the PHY will enter hibernation mode after about 10 seconds
and the PHY clocks will be stopped to save power.
However, some MACs need the phy output clock for proper
functioning of their logic. For instance, stmmac needs the
RX_CLK of PHY for software reset to complete.
Therefore, add a DT property to configure the PHY to disable
this hardware hibernation mode.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 451ef36bd2 ("ip_tunnels: Add new flow flags field to ip_tunnel_key")
added a "flow_flags" member to struct ip_tunnel_key which was later used by
the commit in the fixes tag to avoid dropping packets with sources that
aren't locally configured when set in bpf_set_tunnel_key().
VXLAN and GENEVE were made to respect this flag, ip tunnels like IPIP and GRE
were not.
This commit fixes this omission by making ip_tunnel_init_flow() receive
the flow flags from the tunnel key in the relevant collect_md paths.
Fixes: b8fff74852 ("bpf: Set flow flag to allow any source IP in bpf_tunnel_key")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Paul Chaignon <paul@isovalent.com>
Link: https://lore.kernel.org/bpf/20220818074118.726639-1-eyal.birger@gmail.com
This device does not remember its MAC address, so add a possibility
to get it from the platform. If it fails, generate a random address.
This will provide a MAC address early during boot without user space
being involved.
Also remove extra calls to is_valid_ether_addr().
Made after suggestions by Andrew Lunn:
1) Use eth_hw_addr_random() to assign a random MAC address during probe.
2) Remove is_valid_ether_addr() from moxart_mac_open()
3) Add a call to platform_get_ethdev_address() during probe
4) Remove is_valid_ether_addr() from moxart_set_mac_address(). The core does this
v1 -> v2:
Handle EPROBE_DEFER returned from platform_get_ethdev_address().
Move MAC reading code to the beginning of the probe function.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
CC: Yang Yingliang <yangyingliang@huawei.com>
CC: Pavel Skripkin <paskripkin@gmail.com>
CC: Guobin Huang <huangguobin4@huawei.com>
CC: Yang Wei <yang.wei9@zte.com.cn>
CC: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220818092317.529557-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cong Wang says:
====================
tcp: some bug fixes for tcp_read_skb()
This patchset contains 3 bug fixes and 1 minor refactor patch for
tcp_read_skb(). V1 only had the first patch, as Eric prefers to fix all
of them together, I have to group them together.
====================
Link: https://lore.kernel.org/r/20220817195445.151609-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When skb->len==0, the recv_actor() returns 0 too, but we also use 0
for error conditions. This patch amends this by propagating the errors
to tcp_read_skb() so that we can distinguish skb->len==0 case from
error cases.
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp_cleanup_rbuf() retrieves the skb from sk_receive_queue, it
assumes the skb is not yet dequeued. This is no longer true for
tcp_read_skb() case where we dequeue the skb first.
Fix this by introducing a helper __tcp_cleanup_rbuf() which does
not require any skb and calling it in tcp_read_skb().
Fixes: 04919bed94 ("tcp: Introduce tcp_read_skb()")
Cc: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Before commit 965b57b469 ("net: Introduce a new proto_ops
->read_skb()"), skb was not dequeued from receive queue hence
when we close TCP socket skb can be just flushed synchronously.
After this commit, we have to uncharge skb immediately after being
dequeued, otherwise it is still charged in the original sock. And we
still need to retain skb->sk, as eBPF programs may extract sock
information from skb->sk. Therefore, we have to call
skb_set_owner_sk_safe() here.
Fixes: 965b57b469 ("net: Introduce a new proto_ops ->read_skb()")
Reported-and-tested-by: syzbot+a0e6f8738b58f7654417@syzkaller.appspotmail.com
Tested-by: Stanislav Fomichev <sdf@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit c23d92b80e ("igb: Teardown SR-IOV before
unregister_netdev()") places the unregister_netdev() call after the
igb_disable_sriov() call to avoid functionality issue.
However, it introduces several race conditions when detaching a device.
For example, when .remove() is called, the below interleaving leads to
use-after-free.
(FREE from device detaching) | (USE from netdev core)
igb_remove | igb_ndo_get_vf_config
igb_disable_sriov | vf >= adapter->vfs_allocated_count?
kfree(adapter->vf_data) |
adapter->vfs_allocated_count = 0 |
| memcpy(... adapter->vf_data[vf]
Moreover, the igb_disable_sriov() also suffers from data race with the
requests from VF driver.
(FREE from device detaching) | (USE from requests)
igb_remove | igb_msix_other
igb_disable_sriov | igb_msg_task
kfree(adapter->vf_data) | vf < adapter->vfs_allocated_count
adapter->vfs_allocated_count = 0 |
To this end, this commit first eliminates the data races from netdev
core by using rtnl_lock (similar to commit 7194792308 ("dpaa2-eth: add
MAC/PHY support through phylink")). And then adds a spinlock to
eliminate races from driver requests. (similar to commit 1e53834ce5
("ixgbe: Add locking to prevent panic when setting sriov_numvfs to zero")
Fixes: c23d92b80e ("igb: Teardown SR-IOV before unregister_netdev()")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220817184921.735244-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-17 (ice)
This series contains updates to ice driver only.
Grzegorz prevents modifications to VLAN 0 when setting VLAN promiscuous
as it will already be set. He also ignores -EEXIST error when attempting
to set promiscuous and ensures promiscuous mode is properly cleared from
the hardware when being removed.
Benjamin ignores additional -EEXIST errors when setting promiscuous mode
since the existing mode is the desired mode.
Sylwester fixes VFs to allow sending of tagged traffic when no VLAN filters
exist.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix VF not able to send tagged traffic with no VLAN filters
ice: Ignore error message when setting same promiscuous mode
ice: Fix clearing of promisc mode with bridge over bond
ice: Ignore EEXIST when setting promisc mode
ice: Fix double VLAN error when entering promisc mode
====================
Link: https://lore.kernel.org/r/20220817171329.65285-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On distros whose texlive packaging is fine-grained, texlive-xecjk
can be installed/removed independently of other texlive packages.
Conditionally loading xeCJK depending only on the existence of the
"Noto Sans CJK SC" font might end up in xelatex error of
"xeCJK.sty not found!".
Improve the situation by testing existence of xeCJK.sty before
loading it.
This is useful on RHEL 9 and its clone distros where texlive-xecjk
doesn't work at the moment due to a missing dependency [1].
"make pdfdocs" for non-CJK contents should work after removing
texlive-xecjk.
Link: [1] https://bugzilla.redhat.com/show_bug.cgi?id=2086254
Fixes: 398f7abdcb ("docs: pdfdocs: Pull LaTeX preamble part out of conf.py")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lore.kernel.org/r/c24c2a87-70b2-5342-bcc9-de467940466e@gmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Commit 09f012e64e ("stmmac: intel: Fix clock handling on error and remove
paths") removed this clk_disable_unprepare()
This was partly revert by commit ac322f86b5 ("net: stmmac: Fix clock
handling on remove path") which removed this clk_disable_unprepare()
because:
"
While unloading the dwmac-intel driver, clk_disable_unprepare() is
being called twice in stmmac_dvr_remove() and
intel_eth_pci_remove(). This causes kernel panic on the second call.
"
However later on, commit 5ec5582343 ("net: stmmac: add clocks management
for gmac driver") has updated stmmac_dvr_remove() which do not call
clk_disable_unprepare() anymore.
So this call should now be called from intel_eth_pci_remove().
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/d7c8c1dadf40df3a7c9e643f76ffadd0ccc1ad1b.1660659689.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With special lengths supplied by user space, register_shm_helper() has
an integer overflow when calculating the number of pages covered by a
supplied user space memory region.
This causes internal_get_user_pages_fast() a helper function of
pin_user_pages_fast() to do a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
Modules linked in:
CPU: 1 PID: 173 Comm: optee_example_a Not tainted 5.19.0 #11
Hardware name: QEMU QEMU Virtual Machine, BIOS 0.0.0 02/06/2015
pc : internal_get_user_pages_fast+0x474/0xa80
Call trace:
internal_get_user_pages_fast+0x474/0xa80
pin_user_pages_fast+0x24/0x4c
register_shm_helper+0x194/0x330
tee_shm_register_user_buf+0x78/0x120
tee_ioctl+0xd0/0x11a0
__arm64_sys_ioctl+0xa8/0xec
invoke_syscall+0x48/0x114
Fix this by adding an an explicit call to access_ok() in
tee_shm_register_user_buf() to catch an invalid user space address
early.
Fixes: 033ddf12bc ("tee: add register user memory")
Cc: stable@vger.kernel.org
Reported-by: Nimish Mishra <neelam.nimish@gmail.com>
Reported-by: Anirban Chakraborty <ch.anirban00727@gmail.com>
Reported-by: Debdeep Mukhopadhyay <debdeep.mukhopadhyay@gmail.com>
Suggested-by: Jerome Forissier <jerome.forissier@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pages allocated with GFP_ATOMIC cannot come from Highmem. This is why
there is no need to call kmap() on them.
Therefore, don't call kmap() on rx_buffer->page() and instead use a
plain page_address() to get the kernel address.
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove non-inclusive language from the driver where
possible; replace "master" with "primary"; replace
"slave" with "secondary".
Signed-off-by: Mikael Barsehyan <mikael.barsehyan@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove ucast_shared as it was always true. Remove the code depending on
ucast_shared from ice_add_mac and ice_remove_mac.
Remove ice_find_ucast_rule_entry function as it was only
used when ucast_shared was set to false.
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current code tries to handle the case where CONFIG_PM isn't selected
by first calling our runtime_resume implementation and then properly
report the power state to the runtime_pm core.
This allows to have a functionning device even if pm_runtime_get_*
functions are nops.
However, the device power state if CONFIG_PM is enabled is
RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls
in the runtime_pm hooks will now report a warning since the device might
not be properly powered.
Even more so, we need CONFIG_PM enabled since the previous RaspberryPi
have a power domain that needs to be powered up for the HDMI controller
to be usable.
The previous patch has created a dependency on CONFIG_PM, now we can
just assume it's there and only call pm_runtime_resume_and_get() to make
sure our device is powered in bind.
Link: https://lore.kernel.org/r/20220629123510.1915022-39-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
(cherry picked from commit 53565c28e6)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Make sure that only the valid combinations of FCS/CRC stripping and
VLAN stripping offloads are allowed.
You cannot have FCS/CRC stripping disabled while VLAN stripping is
enabled - this breaks the correctness of the FCS/CRC.
If administrator tries to enable VLAN stripping when FCS/CRC stripping is
disabled, the request should be rejected.
If administrator tries to disable FCS/CRC stripping when VLAN stripping
is enabled, the request should be rejected if VLANs are configured. If
there is no VLAN configured, then both FCS/CRC and VLAN stripping should
be disabled.
Testing Hints:
The default settings after driver load are:
- VLAN C-Tag offloads are enabled
- VLAN S-Tag offloads are disabled
- FCS/CRC stripping is enabled
Restore the default settings before each test with the command:
ethtool -K eth0 rx-fcs off rxvlan on txvlan on rx-vlan-stag-hw-parse off
tx-vlan-stag-hw-insert off
Test 1:
Disable FCS/CRC and VLAN stripping:
ethtool -K eth0 rx-fcs on rxvlan off
Try to enable VLAN stripping:
ethtool -K eth0 rxvlan on
Expected: VLAN stripping request is rejected
Test 2:
Try to disable FCS/CRC stripping:
ethtool -K eth0 rx-fcs on
Expected: VLAN stripping is also disabled, as there are no VLAN
configured
Test 3:
Add a VLAN:
ip link add link eth0 eth0.42 type vlan id 42
ip link set eth0 up
Try to disable FCS/CRC stripping:
ethtool -K eth0 rx-fcs on
Expected: FCS/CRC stripping request is rejected
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver can allow the user to configure whether the CRC aka the FCS
(Frame Check Sequence) is DMA'd to the host as part of the receive
buffer. The driver usually wants this feature disabled so that the
hardware checks the FCS and strips it in order to save PCI bandwidth.
Control the reception of FCS to the host using the command:
ethtool -K eth0 rx-fcs <on|off>
The default shown in ethtool -k eth0 | grep fcs; should be "off", as the
hardware will drop any frame with a bad checksum, and DMA of the
checksum is useless overhead especially for small packets.
Testing Hints:
test the FCS/CRC arrives with received packets using
tcpdump -nnpi eth0 -xxxx
and it should show crc data as the last 4 bytes of the packet. Can also
use wireshark to turn on CRC checking and check the data is correct.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Co-developed-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We do test on a virtio scsi device (/dev/sda) and the default mq
scheduler is 'none'. We found a IO hung as following:
blk_finish_plug
blk_mq_plug_issue_direct
scsi_mq_get_budget
//get budget_token fail and sdev->restarts=1
scsi_end_request
scsi_run_queue_async
//sdev->restart=0 and run queue
blk_mq_request_bypass_insert
//add request to hctx->dispatch list
//continue to dispath plug list
blk_mq_dispatch_plug_list
blk_mq_try_issue_list_directly
//success issue all requests from plug list
After .get_budget fail, scsi_mq_get_budget will increase 'restarts'.
Normally, it will run hw queue when io complete and set 'restarts'
as 0. But if we run queue before adding request to the dispatch list
and blk_mq_dispatch_plug_list also success issue all requests, then
on one will run queue, and the request will be stall in the dispatch
list and cannot complete forever.
It is wrong to use last request of plug list to decide if run queue is
needed since all the remained requests in plug list may be from other
hctxs. To fix the bug, pass run_queue as true always to
blk_mq_request_bypass_insert().
Fix-suggested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Fixes: dc5fc361d8 ("block: attempt direct issue of plug list")
Link: https://lore.kernel.org/r/20220803023355.3687360-1-yuyufen@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Older Intel CPUs that are not in the affected processor list for MMIO
Stale Data vulnerabilities currently report "Not affected" in sysfs,
which may not be correct. Vulnerability status for these older CPUs is
unknown.
Add known-not-affected CPUs to the whitelist. Report "unknown"
mitigation status for CPUs that are not in blacklist, whitelist and also
don't enumerate MSR ARCH_CAPABILITIES bits that reflect hardware
immunity to MMIO Stale Data vulnerabilities.
Mitigation is not deployed when the status is unknown.
[ bp: Massage, fixup. ]
Fixes: 8d50cdf8b8 ("x86/speculation/mmio: Add sysfs reporting for Processor MMIO Stale Data")
Suggested-by: Andrew Cooper <andrew.cooper3@citrix.com>
Suggested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/a932c154772f2121794a5f2eded1a11013114711.1657846269.git.pawan.kumar.gupta@linux.intel.com
This restores the call to inode_has_no_xattr() in the function
__file_remove_privs(). In case the dentry_meeds_remove_privs() returned
0, the function inode_has_no_xattr() was not called.
Signed-off-by: Stefan Roesch <shr@fb.com>
Fixes: faf99b5635 ("fs: add __remove_file_privs() with flags parameter")
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Link: https://lore.kernel.org/r/20220816153158.1925040-1-shr@fb.com
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
IPsec code relies on valid priv->fs pointer that is the case in NIC
flow, but not correct in uplink. Before commit that mentioned in the
Fixes line, that pointer was valid in all flows as it was allocated
together with priv struct.
In addition, the cleanup representors routine called to that
not-initialized priv->fs pointer and its internals which caused NULL
deference.
So, move FS allocation to be as early as possible.
Fixes: af8bbf7300 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/ae46fa5bed3c67f937bfdfc0370101278f5422f1.1660639564.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
Fixes for Ocelot driver statistics
This series contains bug fixes for the ocelot drivers (both switchdev
and DSA). Some concern the counters exposed to ethtool -S, and others to
the counters exposed to ifconfig. I'm aware that the changes are fairly
large, but I wanted to prioritize on a proper approach to addressing the
issues rather than a quick hack.
Some of the noticed problems:
- bad register offsets for some counters
- unhandled concurrency leading to corrupted counters
- unhandled 32-bit wraparound of ifconfig counters
The issues on the ocelot switchdev driver were noticed through code
inspection, I do not have the hardware to test.
This patch set necessarily converts ocelot->stats_lock from a mutex to a
spinlock. I know this affects Colin Foster's development with the SPI
controlled VSC7512. I have other changes prepared for net-next that
convert this back into a mutex (along with other changes in this area).
====================
Link: https://lore.kernel.org/r/20220816135352.1431497-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than reading the stats64 counters directly from the 32-bit
hardware, it's better to rely on the output produced by the periodic
ocelot_port_update_stats().
It would be even better to call ocelot_port_update_stats() right from
ocelot_get_stats64() to make sure we report the current values rather
than the ones from 2 seconds ago. But we need to export
ocelot_port_update_stats() from the switch lib towards the switchdev
driver for that, and future work will largely undo that.
There are more ocelot-based drivers waiting to be introduced, an example
of which is the SPI-controlled VSC7512. In that driver's case, it will
be impossible to call ocelot_port_update_stats() from ndo_get_stats64
context, since the latter is atomic, and reading the stats over SPI is
sleepable. So the compromise taken here, which will also hold going
forward, is to report 64-bit counters to stats64, which are not 100% up
to date.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With so many counter addresses recently discovered as being wrong, it is
desirable to at least have a central database of information, rather
than two: one through the SYS_COUNT_* registers (used for
ndo_get_stats64), and the other through the offset field of struct
ocelot_stat_layout elements (used for ethtool -S).
The strategy will be to keep the SYS_COUNT_* definitions as the single
source of truth, but for that we need to expand our current definitions
to cover all registers. Then we need to convert the ocelot region
creation logic, and stats worker, to the read semantics imposed by going
through SYS_COUNT_* absolute register addresses, rather than offsets
of 32-bit words relative to SYS_COUNT_RX_OCTETS (which should have been
SYS_CNT, by the way).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot counters are 32-bit and require periodic reading, every 2
seconds, by ocelot_port_update_stats(), so that wraparounds are
detected.
Currently, the counters reported by ocelot_get_stats64() come from the
32-bit hardware counters directly, rather than from the 64-bit
accumulated ocelot->stats, and this is a problem for their integrity.
The strategy is to make ocelot_get_stats64() able to cherry-pick
individual stats from ocelot->stats the way in which it currently reads
them out from SYS_COUNT_* registers. But currently it can't, because
ocelot->stats is an opaque u64 array that's used only to feed data into
ethtool -S.
To solve that problem, we need to make ocelot->stats indexable, and
associate each element with an element of struct ocelot_stat_layout used
by ethtool -S.
This makes ocelot_stat_layout a fat (and possibly sparse) array, so we
need to change the way in which we access it. We no longer need
OCELOT_STAT_END as a sentinel, because we know the array's size
(OCELOT_NUM_STATS). We just need to skip the array elements that were
left unpopulated for the switch revision (ocelot, felix, seville).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 2 methods can run concurrently, and one will change the window of
counters (SYS_STAT_CFG_STAT_VIEW) that the other sees. The fix is
similar to what commit 7fbf6795d1 ("net: mscc: ocelot: fix mutex lock
error during ethtool stats read") has done for ethtool -S.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_get_stats64() currently runs unlocked and therefore may collide
with ocelot_port_update_stats() which indirectly accesses the same
counters. However, ocelot_get_stats64() runs in atomic context, and we
cannot simply take the sleepable ocelot->stats_lock mutex. We need to
convert it to an atomic spinlock first. Do that as a preparatory change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This register, used as part of stats->tx_dropped in
ocelot_get_stats64(), has a wrong address. At the address currently
given, there is actually the c_tx_green_prio_6 counter.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reading stats using the SYS_COUNT_* register definitions is only used by
ocelot_get_stats64() from the ocelot switchdev driver, however,
currently the bucket definitions are incorrect.
Separately, on both RX and TX, we have the following problems:
- a 256-1023 bucket which actually tracks the 256-511 packets
- the 1024-1526 bucket actually tracks the 512-1023 packets
- the 1527-max bucket actually tracks the 1024-1526 packets
=> nobody tracks the packets from the real 1527-max bucket
Additionally, the RX_PAUSE, RX_CONTROL, RX_LONGS and RX_CLASSIFIED_DROPS
all track the wrong thing. However this doesn't seem to have any
consequence, since ocelot_get_stats64() doesn't use these.
Even though this problem only manifests itself for the switchdev driver,
we cannot split the fix for ocelot and for DSA, since it requires fixing
the bucket definitions from enum ocelot_reg, which makes us necessarily
adapt the structures from felix and seville as well.
Fixes: 84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
What the driver actually reports as 256-511 is in fact 512-1023, and the
TX packets in the 256-511 bucket are not reported. Fix that.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ds->ops->port_stp_state_set() is, like most DSA methods, optional, and
if absent, the port is supposed to remain in the forwarding state (as
standalone). Such is the case with the mv88e6060 driver, which does not
offload the bridge layer. DSA warns that the STP state can't be changed
to FORWARDING as part of dsa_port_enable_rt(), when in fact it should not.
The error message is also not up to modern standards, so take the
opportunity to make it more descriptive.
Fixes: fd36454131 ("net: dsa: change scope of STP state setter")
Reported-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20220816201445.1809483-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SMB2_ioctl() is always called with is_fsctl = true, so doesn't make any
sense to have it at all.
Thus, always set SMB2_0_IOCTL_IS_FSCTL flag on the request.
Also, as per MS-SMB2 3.3.5.15 "Receiving an SMB2 IOCTL Request", servers
must fail the request if the request flags is zero anyway.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Reviewed-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Andrii Nakryiko says:
====================
bpf-next 2022-08-17
We've added 45 non-merge commits during the last 14 day(s) which contain
a total of 61 files changed, 986 insertions(+), 372 deletions(-).
The main changes are:
1) New bpf_ktime_get_tai_ns() BPF helper to access CLOCK_TAI, from Kurt
Kanzenbach and Jesper Dangaard Brouer.
2) Few clean ups and improvements for libbpf 1.0, from Andrii Nakryiko.
3) Expose crash_kexec() as kfunc for BPF programs, from Artem Savkov.
4) Add ability to define sleepable-only kfuncs, from Benjamin Tissoires.
5) Teach libbpf's bpf_prog_load() and bpf_map_create() to gracefully handle
unsupported names on old kernels, from Hangbin Liu.
6) Allow opting out from auto-attaching BPF programs by libbpf's BPF skeleton,
from Hao Luo.
7) Relax libbpf's requirement for shared libs to be marked executable, from
Henqgi Chen.
8) Improve bpf_iter internals handling of error returns, from Hao Luo.
9) Few accommodations in libbpf to support GCC-BPF quirks, from James Hilliard.
10) Fix BPF verifier logic around tracking dynptr ref_obj_id, from Joanne Koong.
11) bpftool improvements to handle full BPF program names better, from Manu
Bretelle.
12) bpftool fixes around libcap use, from Quentin Monnet.
13) BPF map internals clean ups and improvements around memory allocations,
from Yafang Shao.
14) Allow to use cgroup_get_from_file() on cgroupv1, allowing BPF cgroup
iterator to work on cgroupv1, from Yosry Ahmed.
15) BPF verifier internal clean ups, from Dave Marchevsky and Joanne Koong.
16) Various fixes and clean ups for selftests/bpf and vmtest.sh, from Daniel
Xu, Artem Savkov, Joanne Koong, Andrii Nakryiko, Shibin Koikkara Reeny.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (45 commits)
selftests/bpf: Few fixes for selftests/bpf built in release mode
libbpf: Clean up deprecated and legacy aliases
libbpf: Streamline bpf_attr and perf_event_attr initialization
libbpf: Fix potential NULL dereference when parsing ELF
selftests/bpf: Tests libbpf autoattach APIs
libbpf: Allows disabling auto attach
selftests/bpf: Fix attach point for non-x86 arches in test_progs/lsm
libbpf: Making bpf_prog_load() ignore name if kernel doesn't support
selftests/bpf: Update CI kconfig
selftests/bpf: Add connmark read test
selftests/bpf: Add existing connection bpf_*_ct_lookup() test
bpftool: Clear errno after libcap's checks
bpf: Clear up confusion in bpf_skb_adjust_room()'s documentation
bpftool: Fix a typo in a comment
libbpf: Add names for auxiliary maps
bpf: Use bpf_map_area_alloc consistently on bpf map creation
bpf: Make __GFP_NOWARN consistent in bpf map creation
bpf: Use bpf_map_area_free instread of kvfree
bpf: Remove unneeded memset in queue_stack_map creation
libbpf: preserve errno across pr_warn/pr_info/pr_debug
...
====================
Link: https://lore.kernel.org/r/20220817215656.1180215-1-andrii@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal says:
====================
netfilter: conntrack and nf_tables bug fixes
The following patchset contains netfilter fixes for net.
Broken since 5.19:
A few ancient connection tracking helpers assume TCP packets cannot
exceed 64kb in size, but this isn't the case anymore with 5.19 when
BIG TCP got merged, from myself.
Regressions since 5.19:
1. 'conntrack -E expect' won't display anything because nfnetlink failed
to enable events for expectations, only for normal conntrack events.
2. partially revert change that added resched calls to a function that can
be in atomic context. Both broken and fixed up by myself.
Broken for several releases (up to original merge of nf_tables):
Several fixes for nf_tables control plane, from Pablo.
This fixes up resource leaks in error paths and adds more sanity
checks for mutually exclusive attributes/flags.
Kconfig:
NF_CONNTRACK_PROCFS is very old and doesn't provide all info provided
via ctnetlink, so it should not default to y. From Geert Uytterhoeven.
Selftests:
rework nft_flowtable.sh: it frequently indicated failure; the way it
tried to detect an offload failure did not work reliably.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
testing: selftests: nft_flowtable.sh: rework test to detect offload failure
testing: selftests: nft_flowtable.sh: use random netns names
netfilter: conntrack: NF_CONNTRACK_PROCFS should no longer default to y
netfilter: nf_tables: check NFT_SET_CONCAT flag if field_count is specified
netfilter: nf_tables: disallow NFT_SET_ELEM_CATCHALL and NFT_SET_ELEM_INTERVAL_END
netfilter: nf_tables: NFTA_SET_ELEM_KEY_END requires concat and interval flags
netfilter: nf_tables: validate NFTA_SET_ELEM_OBJREF based on NFT_SET_OBJECT flag
netfilter: nf_tables: really skip inactive sets when allocating name
netfilter: nfnetlink: re-enable conntrack expectation events
netfilter: nf_tables: fix scheduling-while-atomic splat
netfilter: nf_ct_irc: cap packet search space to 4k
netfilter: nf_ct_ftp: prefer skb_linearize
netfilter: nf_ct_h323: cap packet size at 64k
netfilter: nf_ct_sane: remove pseudo skb linearization
netfilter: nf_tables: possible module reference underflow in error path
netfilter: nf_tables: disallow NFTA_SET_ELEM_KEY_END with NFT_SET_ELEM_INTERVAL_END flag
netfilter: nf_tables: use READ_ONCE and WRITE_ONCE for shared generation id access
====================
Link: https://lore.kernel.org/r/20220817140015.25843-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bpf_sk_reuseport_detach() calls __rcu_dereference_sk_user_data_with_flags()
to obtain the value of sk->sk_user_data, but that function is only usable
if the RCU read lock is held, and neither that function nor any of its
callers hold it.
Fix this by adding a new helper, __locked_read_sk_user_data_with_flags()
that checks to see if sk->sk_callback_lock() is held and use that here
instead.
Alternatively, making __rcu_dereference_sk_user_data_with_flags() use
rcu_dereference_checked() might suffice.
Without this, the following warning can be occasionally observed:
=============================
WARNING: suspicious RCU usage
6.0.0-rc1-build2+ #563 Not tainted
-----------------------------
include/net/sock.h:592 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
5 locks held by locktest/29873:
#0: ffff88812734b550 (&sb->s_type->i_mutex_key#9){+.+.}-{3:3}, at: __sock_release+0x77/0x121
#1: ffff88812f5621b0 (sk_lock-AF_INET){+.+.}-{0:0}, at: tcp_close+0x1c/0x70
#2: ffff88810312f5c8 (&h->lhash2[i].lock){+.+.}-{2:2}, at: inet_unhash+0x76/0x1c0
#3: ffffffff83768bb8 (reuseport_lock){+...}-{2:2}, at: reuseport_detach_sock+0x18/0xdd
#4: ffff88812f562438 (clock-AF_INET){++..}-{2:2}, at: bpf_sk_reuseport_detach+0x24/0xa4
stack backtrace:
CPU: 1 PID: 29873 Comm: locktest Not tainted 6.0.0-rc1-build2+ #563
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Call Trace:
<TASK>
dump_stack_lvl+0x4c/0x5f
bpf_sk_reuseport_detach+0x6d/0xa4
reuseport_detach_sock+0x75/0xdd
inet_unhash+0xa5/0x1c0
tcp_set_state+0x169/0x20f
? lockdep_sock_is_held+0x3a/0x3a
? __lock_release.isra.0+0x13e/0x220
? reacquire_held_locks+0x1bb/0x1bb
? hlock_class+0x31/0x96
? mark_lock+0x9e/0x1af
__tcp_close+0x50/0x4b6
tcp_close+0x28/0x70
inet_release+0x8e/0xa7
__sock_release+0x95/0x121
sock_close+0x14/0x17
__fput+0x20f/0x36a
task_work_run+0xa3/0xcc
exit_to_user_mode_prepare+0x9c/0x14d
syscall_exit_to_user_mode+0x18/0x44
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: cf8c1e9672 ("net: refactor bpf_sk_reuseport_detach()")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Hawkins Jiawei <yin31149@gmail.com>
Link: https://lore.kernel.org/r/166064248071.3502205.10036394558814861778.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This parameter is unused by the called function
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Signed-off-by: Steve French <stfrench@microsoft.com>
