commit b21a142fd2 upstream.
Currently we can get a warning on systems with eDP backlights like so:
nv_backlight: invalid backlight type
WARNING: CPU: 4 PID: 454 at drivers/video/backlight/backlight.c:420
backlight_device_register+0x226/0x250
This happens as a result of us not filling out props.type for the eDP
backlight, even though we do it for all other backlight types.
Since nothing in our driver uses anything but BACKLIGHT_RAW, let's take the
props\.type assignments out of the codepaths for individual backlight types
and just set it unconditionally to prevent this from happening again.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 6eca310e89 ("drm/nouveau/kms/nv50-: Add basic DPCD backlight support for nouveau")
Cc: <stable@vger.kernel.org> # v5.15+
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204193319.451119-1-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 028a73e107 upstream.
On some servers with MGA G200_SE_A (rev 42), booting with Legacy BIOS,
the hardware hangs when using kdump and kexec into the kdump kernel.
This happens when the uncompress code tries to write "Decompressing Linux"
to the VGA Console.
It can be reproduced by writing to the VGA console (0xB8000) after
booting to graphic mode, it generates the following error:
kernel:NMI: PCI system error (SERR) for reason a0 on CPU 0.
kernel:Dazed and confused, but trying to continue
The root cause is the configuration of the MGA GCTL6 register
According to the GCTL6 register documentation:
bit 0 is gcgrmode:
0: Enables alpha mode, and the character generator addressing system is
activated.
1: Enables graphics mode, and the character addressing system is not
used.
bit 1 is chainodd even:
0: The A0 signal of the memory address bus is used during system memory
addressing.
1: Allows A0 to be replaced by either the A16 signal of the system
address (ifmemmapsl is ‘00’), or by the hpgoddev (MISC<5>, odd/even
page select) field, described on page 3-294).
bit 3-2 are memmapsl:
Memory map select bits 1 and 0. VGA.
These bits select where the video memory is mapped, as shown below:
00 => A0000h - BFFFFh
01 => A0000h - AFFFFh
10 => B0000h - B7FFFh
11 => B8000h - BFFFFh
bit 7-4 are reserved.
Current code set it to 0x05 => memmapsl to b01 => 0xa0000 (graphic mode)
But on x86, the VGA console is at 0xb8000 (text mode)
In arch/x86/boot/compressed/misc.c debug strings are written to 0xb8000
As the driver doesn't use this mapping at 0xa0000, it is safe to set it to
0xb8000 instead, to avoid kernel hang on G200_SE_A rev42, with kexec/kdump.
Thus changing the value 0x05 to 0x0d
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119102905.1194787-1-jfalempe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94fa115f7b upstream.
Some devices use e.g. a portrait panel in a standard laptop casing made
for landscape panels. efifb calls drm_get_panel_orientation_quirk() and
sets fb_info.fbcon_rotate_hint to make fbcon rotate the console so that
it shows up-right instead of on its side.
When switching to simpledrm the fbcon renders on its side. Call the
drm_connector_set_panel_orientation_with_quirk() helper to add
a "panel orientation" property on devices listed in the quirk table,
to make the fbcon (and aware userspace apps) rotate the image to
display properly.
Cc: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221220045.11958-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c3384050d ]
Fix a number of undefined references to drm_kms_helper.ko in
drm_dp_helper.ko:
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_duplicate_state':
drm_dp_mst_topology.c:(.text+0x2df0): undefined reference to `__drm_atomic_helper_private_obj_duplicate_state'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_delayed_destroy_work':
drm_dp_mst_topology.c:(.text+0x370c): undefined reference to `drm_kms_helper_hotplug_event'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_up_req_work':
drm_dp_mst_topology.c:(.text+0x7938): undefined reference to `drm_kms_helper_hotplug_event'
arm-suse-linux-gnueabi-ld: drivers/gpu/drm/dp/drm_dp_mst_topology.o: in function `drm_dp_mst_link_probe_work':
drm_dp_mst_topology.c:(.text+0x82e0): undefined reference to `drm_kms_helper_hotplug_event'
This happens if panel-edp.ko has been configured with
DRM_PANEL_EDP=y
DRM_DP_HELPER=y
DRM_KMS_HELPER=m
which builds DP helpers into the kernel and KMS helpers sa a module.
Making DRM_PANEL_EDP select DRM_KMS_HELPER resolves this problem.
To avoid a resulting cyclic dependency with DRM_PANEL_BRIDGE, don't
make the latter depend on DRM_KMS_HELPER and fix the one DRM bridge
drivers that doesn't already select DRM_KMS_HELPER. As KMS helpers
cannot be selected directly by the user, config symbols should avoid
depending on it anyway.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 3755d35ee1 ("drm/panel: Select DRM_DP_HELPER for DRM_PANEL_EDP")
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Brian Masney <bmasney@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Linux Kernel Functional Testing <lkft@linaro.org>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/478296/
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4e6f55120c upstream.
On TGL/RKL the BIOS likes to use some kind of bogus DBUF layout
that doesn't match what the spec recommends. With a single active
pipe that is not going to be a problem, but with multiple pipes
active skl_commit_modeset_enables() goes into an infinite loop
since it can't figure out any order in which it can commit the
pipes without causing DBUF overlaps between the planes.
We'd need some kind of extra DBUF defrag stage in between to
make the transition possible. But that is clearly way too complex
a solution, so in the name of simplicity let's just sanitize the
DBUF state by simply turning off all planes when we detect a
pipe encroaching on its neighbours' DBUF slices. We only have
to disable the primary planes as all other planes should have
already been disabled (if they somehow were enabled) by
earlier sanitization steps.
And for good measure let's also sanitize in case the DBUF
allocations of the pipes already seem to overlap each other.
Cc: <stable@vger.kernel.org> # v5.14+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4762
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit 15512021eb)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e2b993302f ]
vkms leverages common amdgpu framebuffer creation, and
also as it does not support FB modifier, there is no need
to check tiling flags when initing framebuffer when virtual
display is enabled.
This can fix below calltrace:
amdgpu 0000:00:08.0: GFX9+ requires FB check based on format modifier
WARNING: CPU: 0 PID: 1023 at drivers/gpu/drm/amd/amdgpu/amdgpu_display.c:1150 amdgpu_display_framebuffer_init+0x8e7/0xb40 [amdgpu]
v2: check adev->enable_virtual_display instead as vkms can be
enabled in bare metal as well.
Signed-off-by: Leslie Shi <Yuliang.Shi@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d22336f90 ]
Even if PSR is allowed for a present GPU, there might be no eDP link
which supports PSR.
Fixes: 7089784873 ("drm/amdgpu/display: Only set vblank_disable_immediate when PSR is not enabled")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3743e7f6fc ]
[Why]
Found when running igt@kms_atomic.
Userspace attempts to do a TEST_COMMIT when 0 streams which calls
dc_remove_stream_from_ctx. This in turn calls link_enc_unassign
which ends up modifying stream->link = NULL directly, causing the
global link_enc to be removed preventing further link activity
and future link validation from passing.
[How]
We take care of link_enc unassignment at the start of
link_enc_cfg_link_encs_assign so this call is no longer necessary.
Fixes global state from being modified while unlocked.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 808643ea56 ]
[why]
If DCN30 watermark calc is used for DCN301, the calculated values are
wrong due to the data structure mismatch between DCN30 and DCN301.
However, using the original DCN301 watermark values causes underflow.
[how]
- Add DCN21-style watermark calculations
- Adjust DCN301 watermark values to remove the underflow
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e5a14bce2 ]
Older radeon boards (r2xx-r5xx) had secondary PCI functions
which we solely there for supporting multi-head on OSs with
special requirements. Add them to the unsupported list
as well so we don't attempt to bind to them. The driver
would fail to bind to them anyway, but this does so
in a cleaner way that should not confuse the user.
Cc: stable@vger.kernel.org
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdbeb0dde4 ]
Once we claim all 0x1002 PCI display class devices, we will
need to filter out devices owned by radeon.
v2: rename radeon id array to make it more clear that
the devices are not supported by amdgpu.
add r128, mach64 pci ids as well
Acked-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7089784873 ]
[Why]
PSR currently relies on the kernel's delayed vblank on/off mechanism
as an implicit bufferring mechanism to prevent excessive entry/exit.
Without this delay the user experience is impacted since it can take
a few frames to enter/exit.
[How]
Only allow vblank disable immediate for DC when psr is not supported.
Leave a TODO indicating that this support should be extended in the
future to delay independent of the vblank interrupt.
Fixes: 92020e81dd ("drm/amdgpu/display: set vblank_disable_immediate for DC")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abfaf0eee9 ]
As the possible failure of the allocation, kmemdup() may return NULL
pointer.
Therefore, it should be better to check the 'props2' in order to prevent
the dereference of NULL pointer.
Fixes: 3a87177eb1 ("drm/amdkfd: Add topology support for dGPUs")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e630016e ]
Actual hardware state of CRTC is controlled by the member 'active' in
struct drm_crtc_state instead of the member 'enable', according to the
kernel doc of the member 'enable'. In fact, the drm client modeset
and atomic helpers are using the member 'active' to do the control.
Referencing the member 'enable' of new_crtc_state, the function
crtc_needs_disable() may fail to reflect if CRTC needs disable in
self refresh mode, e.g., when the framebuffer emulation will be blanked
through the client modeset helper with the next commit, the member
'enable' of new_crtc_state is still true while the member 'active' is
false, hence the relevant potential encoder and bridges won't be disabled.
So, let's check new_crtc_state->active to determine if CRTC needs disable
in self refresh mode instead of new_crtc_state->enable.
Fixes: 1452c25b0e ("drm: Add helpers to kick off self refresh mode in drivers")
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Rob Clark <robdclark@chromium.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211230040626.646807-1-victor.liu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1a66c3bc4 ]
Workstation application ANSA/META v21.1.4 get this error dmesg when
running CI test suite provided by ANSA/META:
[drm:amdgpu_gem_va_ioctl [amdgpu]] *ERROR* Couldn't update BO_VA (-16)
This is caused by:
1. create a 256MB buffer in invisible VRAM
2. CPU map the buffer and access it causes vm_fault and try to move
it to visible VRAM
3. force visible VRAM space and traverse all VRAM bos to check if
evicting this bo is valuable
4. when checking a VM bo (in invisible VRAM), amdgpu_vm_evictable()
will set amdgpu_vm->evicting, but latter due to not in visible
VRAM, won't really evict it so not add it to amdgpu_vm->evicted
5. before next CS to clear the amdgpu_vm->evicting, user VM ops
ioctl will pass amdgpu_vm_ready() (check amdgpu_vm->evicted)
but fail in amdgpu_vm_bo_update_mapping() (check
amdgpu_vm->evicting) and get this error log
This error won't affect functionality as next CS will finish the
waiting VM ops. But we'd better clear the error log by checking
the amdgpu_vm->evicting flag in amdgpu_vm_ready() to stop calling
amdgpu_vm_bo_update_mapping() later.
Another reason is amdgpu_vm->evicted list holds all BOs (both
user buffer and page table), but only page table BOs' eviction
prevent VM ops. amdgpu_vm->evicting flag is set only for page
table BOs, so we should use evicting flag instead of evicted list
in amdgpu_vm_ready().
The side effect of this change is: previously blocked VM op (user
buffer in "evicted" list but no page table in it) gets done
immediately.
v2: update commit comments.
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Qiang Yu <qiang.yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6764eb690e upstream.
At boot on the BCM2711, if the HDMI controllers are running, the CRTC
driver will disable itself and its associated HDMI controller to work
around a hardware bug that would leave some pixels stuck in a FIFO.
In order to avoid that issue, we need to run some operations in lockstep
between the CRTC and HDMI controller, and we need to make sure the HDMI
controller will be powered properly.
However, since we haven't enabled it through KMS, the runtime_pm state
is off at this point so we need to make sure the device is powered
through pm_runtime_resume_and_get, and once the operations are complete,
we call pm_runtime_put.
However, the HDMI controller will do that itself in its
post_crtc_powerdown, which means we'll end up calling pm_runtime_put for
a single pm_runtime_get, throwing the reference counting off. Let's
remove the pm_runtime_put call in the CRTC code in order to have the
proper counting.
Fixes: bca10db67b ("drm/vc4: crtc: Make sure the HDMI controller is powered when disabling")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203102003.1114673-1-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
