[ Upstream commit b58262396f ]
The LVDS signal integrity is only guaranteed when the correct enable
sequence (first IPU DI, then LDB) is used. If the LDB display output was
active before the imx-drm driver is loaded (like when a bootsplash was
active) the DI will be disabled by the full IPU reset we do when loading
the driver. The LDB control registers are not part of the IPU range and
thus will remain unchanged.
This leads to the LDB still being active when the DI is getting enabled,
effectively reversing the required enable sequence. Fix this by also
disabling the LDB on driver bind.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd209ef809 ]
Fix following issues related to planar YUV pixel format configuration:
- NV16/61 modes were incorrectly programmed as NV12/21,
- YVU420 was programmed as YUV420 on source,
- YVU420 and YUV422 were programmed as YUV420 on output.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 89610dc2c2 ]
In the situation that DE and SE aren’t shared the same interrupt number,
the Global SE interrupts mask bit MASK_IRQ_EN in MASKIRQ must be set, or
else other mask bits will not work and no SE interrupt will occur. This
patch enables MASK_IRQ_EN for SE to fix this problem.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a47f20eb1 ]
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99ec9e7751 upstream.
The displaylink hardware has such a peculiarity that it doesn't render a
command until next command is received. This produces occasional
corruption, such as when setting 22x11 font on the console, only the first
line of the cursor will be blinking if the cursor is located at some
specific columns.
When we end up with a repeating pixel, the driver has a bug that it leaves
one uninitialized byte after the command (and this byte is enough to flush
the command and render it - thus it fixes the screen corruption), however
whe we end up with a non-repeating pixel, there is no byte appended and
this results in temporary screen corruption.
This patch fixes the screen corruption by always appending a byte 0xAF at
the end of URB. It also removes the uninitialized byte.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76ef6b28ea upstream.
Since we have the ttm and gem vma managers using a subset
of the file address space for objects, and these start at
0x100000000 they will overflow the new mmap checks.
I've checked all the mmap routines I could see for any
bad behaviour but overall most people use GEM/TTM VMA
managers even the legacy drivers have a hashtable.
Reported-and-Tested-by: Arthur Marsh (amarsh04 on #radeon)
Fixes: be83bbf806 (mmap: introduce sane default mmap limits)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6a055b92de ]
Right now the vblank event completion is racing with the atomic update,
which is especially bad when the PRE is in use, as one of the hardware
issue workaround might extend the atomic commit for quite some time.
If the vblank IRQ happens to trigger during that time, we will prematurely
signal the atomic commit completion to userspace, which causes tearing
when userspace re-uses a framebuffer we haven't managed to flip away from
yet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a588a8bb7b ]
The exynos DRM driver uses real-time 'struct timeval' values
for exporting its timestamps to user space. This has multiple
problems:
1. signed seconds overflow in y2038
2. the 'struct timeval' definition is deprecated in the kernel
3. time may jump or go backwards after a 'settimeofday()' syscall
4. other DRM timestamps are in CLOCK_MONOTONIC domain, so they
can't be compared
5. exporting microseconds requires a division by 1000, which may
be slow on some architectures.
The code existed in two places before, but the IPP portion was
removed in 8ded59413c ("drm/exynos: ipp: Remove Exynos DRM
IPP subsystem"), so we no longer need to worry about it.
Ideally timestamps should just use 64-bit nanoseconds instead, but
of course we can't change that now. Instead, this tries to address
the first four points above by using monotonic 'timespec' values.
According to Tobias Jakobi, user space doesn't care about the
timestamp at the moment, so we can change the format. Even if
there is something looking at them, it will work just fine with
monotonic times as long as the application only looks at the
relative values between two events.
Link: https://patchwork.kernel.org/patch/10038593/
Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe9748b7b4 ]
Fixes failure to compile with recent envyas as a result of the 'movw'
alias being removed for v5.
A bit of history:
v3 only has a 16-bit sign-extended immediate mov op. In order to set
the high bits, there's a separate 'sethi' op. envyas validates that
the value passed to mov(imm) is between -0x8000 and 0x7fff. In order
to simplify macros that load both the low and high word, a 'movw'
alias was added which takes an unsigned 16-bit immediate. However the
actual hardware op still sign extends.
v5 has a full 32-bit immediate mov op. The v3 16-bit immediate mov op
is gone (loads 0 into the dst reg). However due to a bug in envyas,
the movw alias still existed, and selected the no-longer-present v3
16-bit immediate mov op. As a result usage of movw on v5 is the same
as mov with a 0x0 argument.
The proper fix throughout is to only ever use the 'movw' alias in
combination with 'sethi'. Anything else should get the sign-extended
validation to ensure that the intended value ends up in the
destination register.
Changes in fuc3 binaries is the result of a different encoding being
selected for a mov with an 8-bit value.
v2: added commit message written by Ilia, thanks for that!
v3: messed up rebasing, now it should apply
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 938ae7259c upstream.
Depending on whether the kernel is compiled with frame-pointer or not,
the temporary memory location used for the bp parameter in these macros
is referenced relative to the stack pointer or the frame pointer.
Hence we can never reference that parameter when we've modified either
the stack pointer or the frame pointer, because then the compiler would
generate an incorrect stack reference.
Fix this by pushing the temporary memory parameter on a known location on
the stack before modifying the stack- and frame pointers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8f48f96db upstream.
Fix `[drm:intel_enable_lvds] *ERROR* timed out waiting for panel to
power on` in kernel log at boot time.
Toshiba Satellite Z930 laptops needs between 1 and 2 seconds to power
on its screen during Intel i915 DRM initialization. This currently
results in a `[drm:intel_enable_lvds] *ERROR* timed out waiting for
panel to power on` message appearing in the kernel log during boot
time and when stopping the machine.
This change increases the timeout of the `intel_enable_lvds` function
from 1 to 5 seconds, letting enough time for the Satellite 930 LCD
screen to power on, and suppressing the error message from the kernel
log.
This patch has been successfully tested on Linux 4.14 running on a
Toshiba Satellite Z930.
[vsyrjala: bump the timeout from 2 to 5 seconds to match the DP
code and properly cover the max hw timeout of ~4 seconds, and
drop the comment about the specific machine since this is not
a particulary surprising issue, nor specific to that one machine]
Signed-off-by: Florent Flament <contact@florentflament.com>
Cc: stable@vger.kernel.org
Cc: Pavel Petrovic <ppetrovic@acm.org>
Cc: Sérgio M. Basto <sergio@serjux.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103414
References: https://bugzilla.kernel.org/show_bug.cgi?id=57591
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180419160700.19828-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 280b54ade5)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75569c182e upstream.
Otherwise, the SQ may skip some of the register writes, or shader waves may
be allocated where we don't expect them, so that as a result we don't actually
reset all of the register SRAMs. This can lead to spurious ECC errors later on
if a shader uses an uninitialized register.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e1df40f40 upstream.
Currently we see sporadic timeouts during CDCLK changing both on BXT and
GLK as reported by the Bugzilla: ticket. It's easy to reproduce this by
changing the frequency in a tight loop after blanking the display. The
upper bound for the completion time is 800us based on my tests, so
increase it from the current 500us to 2ms; with that I couldn't trigger
the problem either on BXT or GLK.
Note that timeouts happened during both the change notification and the
voltage level setting PCODE request. (For the latter one BSpec doesn't
require us to wait for completion before further HW programming.)
This issue is similar to
commit 2c7d0602c8 ("drm/i915/gen9: Fix PCODE polling during CDCLK
change notification")
but there the PCODE request does complete (as shown by the mbox
busy flag), only the reply we get from PCODE indicates a failure.
So there we keep resending the request until a success reply, here we
just have to increase the timeout for the one PCODE request we send.
v2:
- s/snb_pcode_request/sandybridge_pcode_write_timeout/ (Ville)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.9
Acked-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103326
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130142939.17983-1-imre.deak@intel.com
(cherry picked from commit e76019a819)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(Rebased for v4.9 stable tree due to upstream intel_cdclk.c, cdclk_state and pcu_lock change)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7eb2c4dd54 upstream.
LSPCON adapters in low-power state may ignore the first I2C write during
TMDS output buffer enabling, resulting in a blank screen even with an
otherwise enabled pipe. Fix this by reading back and validating the
written value a few times.
The problem was noticed on GLK machines with an onboard LSPCON adapter
after entering/exiting DC5 power state. Doing an I2C read of the adapter
ID as the first transaction - instead of the I2C write to enable the
TMDS buffers - returns the correct value. Based on this we assume that
the transaction itself is sent properly, it's only the adapter that is
not ready for some reason to accept this first write after waking from
low-power state. In my case the second I2C write attempt always
succeeded.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105854
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180416155309.11100-1-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85e290d92b upstream.
Two years ago I tried an AMD Radeon E8860 embedded GPU with the drm driver.
The dmesg output included driver warnings about an invalid PCIe lane width.
Tracking the problem back led to si_set_pcie_lane_width_in_smc().
The calculation of the lane widths via ATOM_PPLIB_PCIE_LINK_WIDTH_MASK and
ATOM_PPLIB_PCIE_LINK_WIDTH_SHIFT macros did not increment the resulting
value, per the comment in pptable.h ("lanes - 1"), and per usage elsewhere.
Applying the increment silenced the warnings.
The code has not changed since, so either my analysis was incorrect or the
bug has gone unnoticed. Hence submitting this as an RFC.
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f9e93fed4 upstream.
Calling request_irq() followed by disable_irq() is usually a bad idea,
specially if the interrupt can be pending, and you're not yet in a
position to handle it.
This is exactly what happens on my kevin system when rebooting in a
second kernel using kexec: Some interrupt is left pending from
the previous kernel, and we take it too early, before disable_irq()
could do anything.
Let's clear the pending interrupts as we initialize the HW, and move
the interrupt request after that point. This ensures that we're in
a sane state when the interrupt is requested.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[adapted to recent rockchip-drm changes]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220130120.5254-2-marc.zyngier@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a20ee0b1f8 upstream.
If these bos are evicted and are in the validated list
things blow up, so do not put them in there. Notably,
that tries to add the bo to the LRU twice, which results
in a BUG_ON in ttm_bo.c.
While for the bo_list an alternative would be to not allow
always valid bos in there, that does not work for the user
fence.
v2: Fixed whitespace issue pointed out by checkpatch.pl
Signed-off-by: Bas Nieuwenhuizen <basni@chromium.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c02216acf4 upstream.
In randconfig testing, we sometimes get this warning:
drivers/gpu/drm/radeon/radeon_object.c: In function 'radeon_bo_create':
drivers/gpu/drm/radeon/radeon_object.c:242:2: error: #warning Please enable CONFIG_MTRR and CONFIG_X86_PAT for better performance thanks to write-combining [-Werror=cpp]
#warning Please enable CONFIG_MTRR and CONFIG_X86_PAT for better performance \
This is rather annoying since almost all other code produces no build-time
output unless we have found a real bug. We already fixed this in the
amdgpu driver in commit 31bb90f1cd ("drm/amdgpu: shut up #warning for
compile testing") by adding a CONFIG_COMPILE_TEST check last year and
agreed to do the same here, but both Michel and I then forgot about it
until I came across the issue again now.
For stable kernels, as this is one of very few remaining randconfig
warnings in 4.14.
Cc: stable@vger.kernel.org
Link: https://patchwork.kernel.org/patch/9550009/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0b1d259a4 ]
If one 'drm_gem_handle_create()' fails, we leak somes handles and some
memory.
In order to fix it:
- move the 'free(bo_state)' at the end of the function so that it is also
called in the eror handling path. This has the side effect to also try
to free it if the first 'kcalloc' fails. This is harmless.
- add a new label, err_delete_handle, in order to delete already
allocated handles in error handling path
- remove the now useless 'err' label
The way the code is now written will also delete the handles if the
'copy_to_user()' call fails.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170512123803.1886-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc8dd7661c ]
omap_gem uses page alignment for buffer stride. The related calculations
are a bit off, though, as byte stride of 4096 gets aligned to 8192,
instead of 4096.
This patch changes the code to use DIV_ROUND_UP(), which fixes those
calculations and makes them more readable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49baeb0747 ]
The generic connectors such as hdmi-connector doesn't have any driver in,
so if they are added to the component list, we will be waiting forever for
a non-existing driver to probe.
Add a list of the connectors we want to ignore when building our component
list.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90dd57de4a ]
Amongst its other duties, msm_gem_new_impl adds the newly created
GEM object to the shared inactive list which may also be actively
modifiying the list during submission. All the paths to modify
the list are protected by the mutex except for the one through
msm_gem_import which can end up causing list corruption.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[add extra WARN_ON(!mutex_is_locked(&dev->struct_mutex))]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73a88250b7 upstream.
When validating legacy surfaces, the backup bo might be destroyed at
surface validate time. However, the kms resource validation code may have
the bo reserved, so we will destroy a locked mutex. While there shouldn't
be any other users of that mutex when it is destroyed, it causes a lock
leak and thus throws a lockdep error.
Fix this by having the kms resource validation code hold a reference to
the bo while we have it reserved. We do this by introducing a validation
context which might come in handy when the kms code is extended to validate
multiple resources or buffers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
