Pull irq fix from Thomas Gleixner:
"A single commit to handle an erratum in Cavium ThunderX to prevent
access to GIC registers which are broken in the implementation"
* tag 'irq-urgent-2020-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Workaround Cavium erratum 38539 when reading GICD_TYPER2
Pull EFI fixes from Thomas Gleixner:
"Two EFI fixes:
- Prevent a race and buffer overflow in the sysfs efivars interface
which causes kernel memory corruption.
- Add the missing NULL pointer checks in efivar_store_raw()"
* tag 'efi-urgent-2020-03-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Add a sanity check to efivar_store_raw()
efi: Fix a race and a buffer overflow while reading efivars via sysfs
Pull IOMMU fixes from Joerg Roedel:
- Intel VT-d fixes:
- RCU list handling fixes
- Replace WARN_TAINT with pr_warn + add_taint for reporting firmware
issues
- DebugFS fixes
- Fix for hugepage handling in iova_to_phys implementation
- Fix for handling VMD devices, which have a domain number which
doesn't fit into 16 bits
- Warning message fix
- MSI allocation fix for iommu-dma code
- Sign-extension fix for io page-table code
- Fix for AMD-Vi to properly update the is-running bit when AVIC is
used
* tag 'iommu-fixes-v5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Populate debugfs if IOMMUs are detected
iommu/amd: Fix IOMMU AVIC not properly update the is_run bit in IRTE
iommu/vt-d: Ignore devices with out-of-spec domain number
iommu/vt-d: Fix the wrong printing in RHSA parsing
iommu/vt-d: Fix debugfs register reads
iommu/vt-d: quirk_ioat_snb_local_iommu: replace WARN_TAINT with pr_warn + add_taint
iommu/vt-d: dmar_parse_one_rmrr: replace WARN_TAINT with pr_warn + add_taint
iommu/vt-d: dmar: replace WARN_TAINT with pr_warn + add_taint
iommu/vt-d: Silence RCU-list debugging warnings
iommu/vt-d: Fix RCU-list bugs in intel_iommu_init()
iommu/dma: Fix MSI reservation allocation
iommu/io-pgtable-arm: Fix IOVA validation for 32-bit
iommu/vt-d: Fix a bug in intel_iommu_iova_to_phys() for huge page
iommu/vt-d: Fix RCU list debugging warnings
Pull i2c fixes from Wolfram Sang:
"I2C has quite some regression fixes this time.
One is also related to watchdogs, we have proper acks from Guenter for
them"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: acpi: put device when verifying client fails
misc: eeprom: at24: fix regulator underflow
i2c: gpio: suppress error on probe defer
macintosh: windfarm: fix MODINFO regression
i2c: designware-pci: Fix BUG_ON during device removal
i2c: i801: Do not add ICH_RES_IO_SMI for the iTCO_wdt device
watchdog: iTCO_wdt: Make ICH_RES_IO_SMI optional
watchdog: iTCO_wdt: Export vendorsupport
Currently, the intel iommu debugfs directory(/sys/kernel/debug/iommu/intel)
gets populated only when DMA remapping is enabled (dmar_disabled = 0)
irrespective of whether interrupt remapping is enabled or not.
Instead, populate the intel iommu debugfs directory if any IOMMUs are
detected.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: ee2636b867 ("iommu/vt-d: Enable base Intel IOMMU debugfs support")
Signed-off-by: Megha Dey <megha.dey@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull clk fixes from Stephen Boyd:
"A small collection of fixes. I'll make another sweep soon to look for
more fixes for this -rc series.
- Mark device node const in of_clk_get_parent APIs to ease landing
changes in users later
- Fix flag for Qualcomm SC7180 video clocks where we thought it would
never turn off but actually hardware takes care of it
- Remove disp_cc_mdss_rscc_ahb_clk on Qualcomm SC7180 SoCs because
this clk is always on anyway
- Correct some bad dt-binding numbers for i.MX8MN SoCs"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx8mn: Fix incorrect clock defines
clk: qcom: dispcc: Remove support of disp_cc_mdss_rscc_ahb_clk
clk: qcom: videocc: Update the clock flag for video_cc_vcodec0_core_clk
of: clk: Make of_clk_get_parent_{count,name}() parameter const
Commit b9c6ff94e4 ("iommu/amd: Re-factor guest virtual APIC
(de-)activation code") accidentally left out the ir_data pointer when
calling modity_irte_ga(), which causes the function amd_iommu_update_ga()
to return prematurely due to struct amd_ir_data.ref is NULL and
the "is_run" bit of IRTE does not get updated properly.
This results in bad I/O performance since IOMMU AVIC always generate GA Log
entry and notify IOMMU driver and KVM when it receives interrupt from the
PCI pass-through device instead of directly inject interrupt to the vCPU.
Fixes by passing ir_data when calling modify_irte_ga() as done previously.
Fixes: b9c6ff94e4 ("iommu/amd: Re-factor guest virtual APIC (de-)activation code")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
VMD subdevices are created with a PCI domain ID of 0x10000 or
higher.
These subdevices are also handled like all other PCI devices by
dmar_pci_bus_notifier().
However, when dmar_alloc_pci_notify_info() take records of such devices,
it will truncate the domain ID to a u16 value (in info->seg).
The device at (e.g.) 10000:00:02.0 is then treated by the DMAR code as if
it is 0000:00:02.0.
In the unlucky event that a real device also exists at 0000:00:02.0 and
also has a device-specific entry in the DMAR table,
dmar_insert_dev_scope() will crash on:
BUG_ON(i >= devices_cnt);
That's basically a sanity check that only one PCI device matches a
single DMAR entry; in this case we seem to have two matching devices.
Fix this by ignoring devices that have a domain number higher than
what can be looked up in the DMAR table.
This problem was carefully diagnosed by Jian-Hong Pan.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Fixes: 59ce0515cd ("iommu/vt-d: Update DRHD/RMRR/ATSR device scope caches when PCI hotplug happens")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When base address in RHSA structure doesn't match base address in
each DRHD structure, the base address in last DRHD is printed out.
This doesn't make sense when there are multiple DRHD units, fix it
by printing the buggy RHSA's base address.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Fixes: fd0c889489 ("intel-iommu: Set a more specific taint flag for invalid BIOS DMAR tables")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Pull SCSI fixes from James Bottomley:
"Two small fixes, both in drivers: ipr and ufs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ipr: Fix softlockup when rescanning devices in petitboot
scsi: ufs: Fix possible unclocked access to auto hibern8 timer register
Pull block fixes from Jens Axboe:
"A few fixes that should go into this release. This contains:
- Fix for a corruption issue with the s390 dasd driver (Stefan)
- Fixup/improvement for the flush insertion change that we had in
this series (Ming)
- Fix for the partition suppor for host aware zoned devices
(Shin'ichiro)
- Fix incorrect blk-iocost comparison (Tejun)
The diffstat looks large, but that's a) mostly dasd, and b) the flush
fix from Ming adds a big comment"
* tag 'block-5.6-2020-03-13' of git://git.kernel.dk/linux-block:
block: Fix partition support for host aware zoned block devices
blk-mq: insert flush request to the front of dispatch queue
s390/dasd: fix data corruption for thin provisioned devices
blk-iocost: fix incorrect vtime comparison in iocg_is_idle()
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix HW busy detection support for host controllers requiring the
MMC_RSP_BUSY response flag (R1B) to be set for the command. In
particular for CMD6 (eMMC), erase/trim/discard (SD/eMMC) and CMD5
(eMMC sleep).
MMC host:
- sdhci-omap|tegra: Fix support for HW busy detection"
* tag 'mmc-v5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Respect MMC_CAP_NEED_RSP_BUSY for eMMC sleep command
mmc: sdhci-tegra: Fix busy detection by enabling MMC_CAP_NEED_RSP_BUSY
mmc: sdhci-omap: Fix busy detection by enabling MMC_CAP_NEED_RSP_BUSY
mmc: core: Respect MMC_CAP_NEED_RSP_BUSY for erase/trim/discard
mmc: core: Allow host controllers to require R1B for CMD6
Quoting from the comment describing the WARN functions in
include/asm-generic/bug.h:
* WARN(), WARN_ON(), WARN_ON_ONCE, and so on can be used to report
* significant kernel issues that need prompt attention if they should ever
* appear at runtime.
*
* Do not use these macros when checking for invalid external inputs
The (buggy) firmware tables which the dmar code was calling WARN_TAINT
for really are invalid external inputs. They are not under the kernel's
control and the issues in them cannot be fixed by a kernel update.
So logging a backtrace, which invites bug reports to be filed about this,
is not helpful.
Fixes: 556ab45f9a ("ioat2: catch and recover from broken vtd configurations v6")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200309182510.373875-1-hdegoede@redhat.com
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=701847
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Quoting from the comment describing the WARN functions in
include/asm-generic/bug.h:
* WARN(), WARN_ON(), WARN_ON_ONCE, and so on can be used to report
* significant kernel issues that need prompt attention if they should ever
* appear at runtime.
*
* Do not use these macros when checking for invalid external inputs
The (buggy) firmware tables which the dmar code was calling WARN_TAINT
for really are invalid external inputs. They are not under the kernel's
control and the issues in them cannot be fixed by a kernel update.
So logging a backtrace, which invites bug reports to be filed about this,
is not helpful.
Some distros, e.g. Fedora, have tools watching for the kernel backtraces
logged by the WARN macros and offer the user an option to file a bug for
this when these are encountered. The WARN_TAINT in dmar_parse_one_rmrr
+ another iommu WARN_TAINT, addressed in another patch, have lead to over
a 100 bugs being filed this way.
This commit replaces the WARN_TAINT("...") call, with a
pr_warn(FW_BUG "...") + add_taint(TAINT_FIRMWARE_WORKAROUND, ...) call
avoiding the backtrace and thus also avoiding bug-reports being filed
about this against the kernel.
Fixes: f5a68bb075 ("iommu/vt-d: Mark firmware tainted if RMRR fails sanity check")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Cc: Barret Rhoden <brho@google.com>
Link: https://lore.kernel.org/r/20200309140138.3753-3-hdegoede@redhat.com
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1808874
Quoting from the comment describing the WARN functions in
include/asm-generic/bug.h:
* WARN(), WARN_ON(), WARN_ON_ONCE, and so on can be used to report
* significant kernel issues that need prompt attention if they should ever
* appear at runtime.
*
* Do not use these macros when checking for invalid external inputs
The (buggy) firmware tables which the dmar code was calling WARN_TAINT
for really are invalid external inputs. They are not under the kernel's
control and the issues in them cannot be fixed by a kernel update.
So logging a backtrace, which invites bug reports to be filed about this,
is not helpful.
Some distros, e.g. Fedora, have tools watching for the kernel backtraces
logged by the WARN macros and offer the user an option to file a bug for
this when these are encountered. The WARN_TAINT in warn_invalid_dmar()
+ another iommu WARN_TAINT, addressed in another patch, have lead to over
a 100 bugs being filed this way.
This commit replaces the WARN_TAINT("...") calls, with
pr_warn(FW_BUG "...") + add_taint(TAINT_FIRMWARE_WORKAROUND, ...) calls
avoiding the backtrace and thus also avoiding bug-reports being filed
about this against the kernel.
Fixes: fd0c889489 ("intel-iommu: Set a more specific taint flag for invalid BIOS DMAR tables")
Fixes: e625b4a95d ("iommu/vt-d: Parse ANDD records")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200309140138.3753-2-hdegoede@redhat.com
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1564895
Pull drm fixes from Dave Airlie:
"It's a bit quieter, probably not as much as it could be.
There is on large regression fix in here from Lyude for displayport
bandwidth calculations, there've been reports of multi-monitor in
docks not working since -rc1 and this has been tested to fix those.
Otherwise it's a bunch of i915 (with some GVT fixes), a set of amdgpu
watermark + bios fixes, and an exynos iommu cleanup fix.
core:
- DP MST bandwidth regression fix.
i915:
- hard lockup fix
- GVT fixes
- 32-bit alignment issue fix
- timeline wait fixes
- cacheline_retire and free
amdgpu:
- Update the display watermark bounding box for navi14
- Fix fetching vbios directly from rom on vega20/arcturus
- Navi and renoir watermark fixes
exynos:
- iommu object cleanup fix"
`
* tag 'drm-fixes-2020-03-13' of git://anongit.freedesktop.org/drm/drm:
drm/dp_mst: Rewrite and fix bandwidth limit checks
drm/dp_mst: Reprobe path resources in CSN handler
drm/dp_mst: Use full_pbn instead of available_pbn for bandwidth checks
drm/dp_mst: Rename drm_dp_mst_is_dp_mst_end_device() to be less redundant
drm/i915: Defer semaphore priority bumping to a workqueue
drm/i915/gt: Close race between cacheline_retire and free
drm/i915/execlists: Enable timeslice on partial virtual engine dequeue
drm/i915: be more solid in checking the alignment
drm/i915/gvt: Fix dma-buf display blur issue on CFL
drm/i915: Return early for await_start on same timeline
drm/i915: Actually emit the await_start
drm/amdgpu/powerplay: nv1x, renior copy dcn clock settings of watermark to smu during boot up
drm/exynos: Fix cleanup of IOMMU related objects
drm/amdgpu: correct ROM_INDEX/DATA offset for VEGA20
drm/amd/display: update soc bb for nv14
drm/i915/gvt: Fix emulated vbt size issue
drm/i915/gvt: Fix unnecessary schedule timer when no vGPU exits
UAPI Changes: None
Cross-subsystem Changes: None
Core Changes: Fixed regressions introduced by commit cd82d82cbc
("drm/dp_mst: Add branch bandwidth validation to MST atomic check"),
which would cause us to:
* Calculate the available bandwidth on an MST topology incorrectly, and
as a result reject most display configurations that would try to enable
more then one sink on a topology
* Occasionally expose MST connectors to userspace before finishing
probing their PBN capabilities, resulting in us rejecting display
configurations because we assumed briefly that no bandwidth was
available
Driver Changes: None
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bf16ee577567beed91c86b7d9cda3ec2e8c50a71.camel@redhat.com
Pull networking fixes from David Miller:
"It looks like a decent sized set of fixes, but a lot of these are one
liner off-by-one and similar type changes:
1) Fix netlink header pointer to calcular bad attribute offset
reported to user. From Pablo Neira Ayuso.
2) Don't double clear PHY interrupts when ->did_interrupt is set,
from Heiner Kallweit.
3) Add missing validation of various (devlink, nl802154, fib, etc.)
attributes, from Jakub Kicinski.
4) Missing *pos increments in various netfilter seq_next ops, from
Vasily Averin.
5) Missing break in of_mdiobus_register() loop, from Dajun Jin.
6) Don't double bump tx_dropped in veth driver, from Jiang Lidong.
7) Work around FMAN erratum A050385, from Madalin Bucur.
8) Make sure ARP header is pulled early enough in bonding driver,
from Eric Dumazet.
9) Do a cond_resched() during multicast processing of ipvlan and
macvlan, from Mahesh Bandewar.
10) Don't attach cgroups to unrelated sockets when in interrupt
context, from Shakeel Butt.
11) Fix tpacket ring state management when encountering unknown GSO
types. From Willem de Bruijn.
12) Fix MDIO bus PHY resume by checking mdio_bus_phy_may_suspend()
only in the suspend context. From Heiner Kallweit"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
net: systemport: fix index check to avoid an array out of bounds access
tc-testing: add ETS scheduler to tdc build configuration
net: phy: fix MDIO bus PM PHY resuming
net: hns3: clear port base VLAN when unload PF
net: hns3: fix RMW issue for VLAN filter switch
net: hns3: fix VF VLAN table entries inconsistent issue
net: hns3: fix "tc qdisc del" failed issue
taprio: Fix sending packets without dequeueing them
net: mvmdio: avoid error message for optional IRQ
net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register
net: memcg: fix lockdep splat in inet_csk_accept()
s390/qeth: implement smarter resizing of the RX buffer pool
s390/qeth: refactor buffer pool code
s390/qeth: use page pointers to manage RX buffer pool
seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number
net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed
net/packet: tpacket_rcv: do not increment ring index on drop
sxgbe: Fix off by one in samsung driver strncpy size arg
net: caif: Add lockdep expression to RCU traversal primitive
MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer
...
Sigh, this is mostly my fault for not giving commit cd82d82cbc
("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
enough scrutiny during review. The way we're checking bandwidth
limitations here is mostly wrong:
For starters, drm_dp_mst_atomic_check_bw_limit() determines the
pbn_limit of a branch by simply scanning each port on the current branch
device, then uses the last non-zero full_pbn value that it finds. It
then counts the sum of the PBN used on each branch device for that
level, and compares against the full_pbn value it found before.
This is wrong because ports can and will have different PBN limitations
on many hubs, especially since a number of DisplayPort hubs out there
will be clever and only use the smallest link rate required for each
downstream sink - potentially giving every port a different full_pbn
value depending on what link rate it's trained at. This means with our
current code, which max PBN value we end up with is not well defined.
Additionally, we also need to remember when checking bandwidth
limitations that the top-most device in any MST topology is a branch
device, not a port. This means that the first level of a topology
doesn't technically have a full_pbn value that needs to be checked.
Instead, we should assume that so long as our VCPI allocations fit we're
within the bandwidth limitations of the primary MSTB.
We do however, want to check full_pbn on every port including those of
the primary MSTB. However, it's important to keep in mind that this
value represents the minimum link rate /between a port's sink or mstb,
and the mstb itself/. A quick diagram to explain:
MSTB #1
/ \
/ \
Port #1 Port #2
full_pbn for Port #1 → | | ← full_pbn for Port #2
Sink #1 MSTB #2
|
etc...
Note that in the above diagram, the combined PBN from all VCPI
allocations on said hub should not exceed the full_pbn value of port #2,
and the display configuration on sink #1 should not exceed the full_pbn
value of port #1. However, port #1 and port #2 can otherwise consume as
much bandwidth as they want so long as their VCPI allocations still fit.
And finally - our current bandwidth checking code also makes the mistake
of not checking whether something is an end device or not before trying
to traverse down it.
So, let's fix it by rewriting our bandwidth checking helpers. We split
the function into one part for handling branches which simply adds up
the total PBN on each branch and returns it, and one for checking each
port to ensure we're not going over its PBN limit. Phew.
This should fix regressions seen, where we erroneously reject display
configurations due to thinking they're going over our bandwidth limits
when they're not.
Changes since v1:
* Took an even closer look at how PBN limitations are supposed to be
handled, and did some experimenting with Sean Paul. Ended up rewriting
these helpers again, but this time they should actually be correct!
Changes since v2:
* Small indenting fix
* Fix pbn_used check in drm_dp_mst_atomic_check_port_bw_limit()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Sean Paul <seanpaul@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309210131.1497545-1-lyude@redhat.com
We used to punt off reprobing path resources to the link address probe
work, but now that we handle CSNs asynchronously from the driver's HPD
handling we can do whatever the heck we want from the CSN!
So, reprobe the path resources from drm_dp_mst_handle_conn_stat(). Also,
get rid of the path resource reprobing code in
drm_dp_check_and_send_link_address() since it's needlessly complicated
when we already reprobe path resources from
drm_dp_handle_link_address_port(). And finally, teach
drm_dp_send_enum_path_resources() to return 1 on PBN changes so we know
if we need to send another hotplug or not.
This fixes issues where we've indicated to userspace that a port has
just been connected, before we actually probed it's available PBN -
something that results in unexpected atomic check failures.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-4-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
DisplayPort specifications are fun. For a while, it's been really
unclear to us what available_pbn actually does. There's a somewhat vague
explanation in the DisplayPort spec (starting from 1.2) that partially
explains it:
The minimum payload bandwidth number supported by the path. Each node
updates this number with its available payload bandwidth number if its
payload bandwidth number is less than that in the Message Transaction
reply.
So, it sounds like available_pbn represents the smallest link rate in
use between the source and the branch device. Cool, so full_pbn is just
the highest possible PBN that the branch device supports right?
Well, we assumed that for quite a while until Sean Paul noticed that on
some MST hubs, available_pbn will actually get set to 0 whenever there's
any active payloads on the respective branch device. This caused quite a
bit of confusion since clearing the payload ID table would end up fixing
the available_pbn value.
So, we just went with that until commit cd82d82cbc ("drm/dp_mst: Add
branch bandwidth validation to MST atomic check") started breaking
people's setups due to us getting erroneous available_pbn values. So, we
did some more digging and got confused until we finally looked at the
definition for full_pbn:
The bandwidth of the link at the trained link rate and lane count
between the DP Source device and the DP Sink device with no time slots
allocated to VC Payloads, represented as a Payload Bandwidth Number. As
with the Available_Payload_Bandwidth_Number, this number is determined
by the link with the lowest lane count and link rate.
That's what we get for not reading specs closely enough, hehe. So, since
full_pbn is definitely what we want for doing bandwidth restriction
checks - let's start using that instead and ignore available_pbn
entirely.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-3-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Currently the bounds check on index is off by one and can lead to
an out of bounds access on array priv->filters_loc when index is
RXCHK_BRCM_TAG_MAX.
Fixes: bb9051a2b2 ("net: systemport: Add support for WAKE_FILTER")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c696 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, PF missed to clear the port base VLAN for VF when
unload. In this case, the VLAN id will remain in the VLAN
table. This patch fixes it.
Fixes: 92f11ea177 ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the user manual, the ingress and egress VLAN filter
are configured at the same time. Currently, hclge_init_vlan_config()
and hclge_set_vlan_spoofchk() will both change the VLAN filter
switch. So it's necessary to read the old configuration before
modifying it.
Fixes: 22044f95fa ("net: hns3: add support for spoof check setting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if VF is loaded on the host side, the host doesn't
clear the VF's VLAN table entries when VF removing. In this
case, when doing reset and disabling sriov at the same time the
VLAN device over VF will be removed, but the VLAN table entries
in hardware are remained.
This patch fixes it by asking PF to clear the VLAN table entries for
VF when VF is removing. It also clears the VLAN table full bit
after VF VLAN table entries being cleared.
Fixes: c6075b1934 ("net: hns3: Record VF vlan tables")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS3 driver supports to configure TC numbers and TC to priority
map via "tc" tool. But when delete the rule, will fail, because
the HNS3 driver needs at least one TC, but the "tc" tool sets TC
number to zero when delete.
This patch makes sure that the TC number is at least one.
Fixes: 30d240dfa2 ("net: hns3: Add mqprio hardware offload support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IPMI fix from Corey Minyard:
"Fix a message spew on some system
The call to platform_get_irq() was changed to print a log if the
interrupt was not available, and that was causing bogus messages to
spew out for the IPMI driver. People have requested that this get in
to 5.6 so I'm sending it along"
* tag 'for-linus-5.6-2' of git://github.com/cminyard/linux-ipmi:
ipmi_si: Avoid spurious errors for optional IRQs
Devices are formatted in multiple of tracks.
For an Extent Space Efficient (ESE) volume we get errors when accessing
unformatted tracks. In this case the driver either formats the track on
the flight for write requests or returns zero data for read requests.
In case a request spans multiple tracks, the indication of an unformatted
track presented for the first track is incorrectly applied to all tracks
covered by the request. As a result, tracks containing data will be handled
as empty, resulting in zero data being returned on read, or overwriting
existing data with zero on write.
Fix by determining the track that gets the NRF error.
For write requests only format the track that is surely not formatted.
For Read requests all tracks before have returned valid data and should not
be touched.
All tracks after the unformatted track might be formatted or not. Those are
returned to the blocklayer to build a new request.
When using alias devices there is a chance that multiple write requests
trigger a format of the same track which might lead to data loss. Ensure
that a track is formatted only once by maintaining a list of currently
processed tracks.
Fixes: 5e2b17e712 ("s390/dasd: Add dynamic formatting support for ESE volumes")
Cc: stable@vger.kernel.org # 5.3+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The busy timeout for the CMD5 to put the eMMC into sleep state, is specific
to the card. Potentially the timeout may exceed the host->max_busy_timeout.
If that becomes the case, mmc_sleep() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200311092036.16084-1-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The at24 driver attempts to read a byte from the device to validate that
it's actually present, and if not, disables the vcc regulator and
returns -ENODEV. However, between the read and the error handling path,
pm_runtime_idle() is called and invokes the driver's suspend callback,
which also disables the vcc regulator. This leads to an underflow of the
regulator enable count if the EEPROM is not present.
Move the pm_runtime_suspend() call to be after the error handling path
to resolve this.
Fixes: cd5676db05 ("misc: eeprom: at24: support pm_runtime control")
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7df ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer pool is allocated in qeth_alloc_qdio_queues().
A subsequent pool resizing is then handled in a very simple way:
first free the current pool, then allocate a new pool of the requested
size.
There's two ways where this can go wrong:
1. if the resize action happens _before_ the initial pool was allocated,
then a subsequent initialization will call qeth_alloc_qdio_queues()
and fill the pool with a second(!) set of pages. We consume twice the
planned amount of memory.
This is easy to fix - just skip the resizing if the queues haven't
been allocated yet.
2. if the initial pool was created by qeth_alloc_qdio_queues() but a
subsequent resizing fails, then the device has no(!) RX buffer pool.
The next initialization will _not_ call qeth_alloc_qdio_queues(), and
attempting to back the RX buffers with pages in
qeth_init_qdio_queues() will fail.
Not very difficult to fix either - instead of re-allocating the whole
pool, just allocate/free as many entries to match the desired size.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for a subsequent fix, split out helpers to allocate/free
individual pool entries.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX buffer elements are always backed with full pages, reflect this
in the pointer type.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an off-by-one error in strncpy size argument in
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c. The issue is that in:
strncmp(opt, "eee_timer:", 6)
the passed string literal: "eee_timer:" has 10 bytes (without the NULL
byte) and the passed size argument is 6. As a result, the logic will
also accept other, malformed strings, e.g. "eee_tiXXX:".
This bug doesn't seem to have any security impact since its present in
module's cmdline parsing code.
Signed-off-by: Dominik Czarnota <dominik.b.czarnota@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_set_coalesce() validates the previously set params
and if they are within range proceeds to apply the new ones.
The new ones, however, are not validated. This seems backwards,
probably a copy-paste error?
Compile tested only.
Fixes: d851b47b22 ("net: fec: add interrupt coalescence feature support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the IRQ assignment in ipmi_si driver is optional,
platform_get_irq() spews error messages unnecessarily:
ipmi_si dmi-ipmi-si.0: IRQ index 0 not found
Fix this by switching to platform_get_irq_optional().
Cc: stable@vger.kernel.org # 5.4.x
Cc: John Donnelly <john.p.donnelly@oracle.com>
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Reported-and-tested-by: Patrick Vo <patrick.vo@hpe.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-Id: <20200205093146.1352-1-tiwai@suse.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
