v5.16-rc1 + 20211207114003.100693-2-vkoul@kernel.org
The immutable branch contains DT binding and in defines for the global
clock controller registers used the the Qualcomm SM8450 dtsi.
Currently Soundcard has 1 rx device for headset and SoundWire Speaker Playback.
This setup has issues, ex if we try to play on headset the audio stream is
also sent to SoundWire Speakers and we will hear sound in both headsets and speakers.
Make a separate device for Speakers and Headset so that the streams are
different and handled properly.
Fixes: 45021d35fc ("arm64: dts: qcom: c630: Enable audio support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211209175342.20386-2-srinivas.kandagatla@linaro.org
The TPS68470 PMIC provides Clocks, GPIOs and Regulators. At present in
the kernel the Regulators and Clocks are controlled by an OpRegion
driver designed to work with power control methods defined in ACPI, but
some platforms lack those methods, meaning drivers need to be able to
consume the resources of these chips through the usual frameworks.
This commit adds a driver for the regulators provided by the tps68470,
and is designed to bind to the platform_device registered by the
intel_skl_int3472 module.
This is based on this out of tree driver written by Intel:
https://github.com/intel/linux-intel-lts/blob/4.14/base/drivers/regulator/tps68470-regulator.c
with various cleanups added.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed tag for the immutable platform-drivers-x86-int3472 branch
This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches.
Signed tag for the immutable platform-drivers-x86-int3472 branch
This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches required so that the tps68570 regulator
driver can be applied.
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d4 ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c6 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73 ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db72727 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 25058d1c72 ("dm integrity: use bvec_kmap_local in
__journal_read_write") didn't account for __journal_read_write() later
adding the biovec's bv_offset. As such using bvec_kmap_local() caused
the start of the biovec to be skipped.
Trivial test that illustrates data corruption:
# integritysetup format /dev/pmem0
# integritysetup open /dev/pmem0 integrityroot
# mkfs.xfs /dev/mapper/integrityroot
...
bad magic number
bad magic number
Metadata corruption detected at xfs_sb block 0x0/0x1000
libxfs_writebufr: write verifer failed on xfs_sb bno 0x0/0x1000
releasing dirty buffer (bulk) to free list!
Fix this by using kmap_local_page() instead of bvec_kmap_local() in
__journal_read_write().
Fixes: 25058d1c72 ("dm integrity: use bvec_kmap_local in __journal_read_write")
Reported-by: Tony Asleson <tasleson@redhat.com>
Reviewed-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
https://sourceforge.net/p/e1000/mailman/message/37106269/
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665ea ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
Fixes: 707abf0695 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
The KASAN logs are as follows:
[ 35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[ 35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[ 35.128360]
[ 35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[ 35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[ 35.131749] Call Trace:
[ 35.132199] dump_stack_lvl+0x59/0x7b
[ 35.132865] print_address_description+0x7c/0x3b0
[ 35.133707] ? free_netdev+0x1fd/0x450
[ 35.134378] __kasan_report+0x160/0x1c0
[ 35.135063] ? free_netdev+0x1fd/0x450
[ 35.135738] kasan_report+0x4b/0x70
[ 35.136367] free_netdev+0x1fd/0x450
[ 35.137006] igbvf_probe+0x121d/0x1a10 [igbvf]
[ 35.137808] ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[ 35.138751] local_pci_probe+0x13c/0x1f0
[ 35.139461] pci_device_probe+0x37e/0x6c0
[ 35.165526]
[ 35.165806] Allocated by task 366:
[ 35.166414] ____kasan_kmalloc+0xc4/0xf0
[ 35.167117] foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[ 35.168078] igbvf_probe+0x9c5/0x1a10 [igbvf]
[ 35.168866] local_pci_probe+0x13c/0x1f0
[ 35.169565] pci_device_probe+0x37e/0x6c0
[ 35.179713]
[ 35.179993] Freed by task 366:
[ 35.180539] kasan_set_track+0x4c/0x80
[ 35.181211] kasan_set_free_info+0x1f/0x40
[ 35.181942] ____kasan_slab_free+0x103/0x140
[ 35.182703] kfree+0xe3/0x250
[ 35.183239] igbvf_probe+0x1173/0x1a10 [igbvf]
[ 35.184040] local_pci_probe+0x13c/0x1f0
Fixes: d4e0fe01a3 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
Fixes: 1b8b062a99 ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Pull ceph fixes from Ilya Dryomov:
"An SGID directory handling fix (marked for stable), a metrics
accounting fix and two fixups to appease static checkers"
* tag 'ceph-for-5.16-rc6' of git://github.com/ceph/ceph-client:
ceph: fix up non-directory creation in SGID directories
ceph: initialize pathlen variable in reconnect_caps_cb
ceph: initialize i_size variable in ceph_sync_read
ceph: fix duplicate increment of opened_inodes metric
Pull s390 fixes from Heiko Carstens:
- Add missing handling of R_390_PLT32DBL relocation type in
arch_kexec_apply_relocations_add(). Clang and the upcoming gcc 11.3
generate such relocation entries, which our relocation code silently
ignores, and which finally will result in an endless loop within the
purgatory code in case of kexec.
- Add proper handling of errors and print error messages when applying
relocations
- Fix duplicate tracking of irq nesting level in entry code
- Let recordmcount.pl also look for jgnop mnemonic. Starting with
binutils 2.37 objdump emits a jgnop mnemonic instead of brcl, which
breaks mcount location detection. This is only a problem if used with
compilers older than gcc 9, since with gcc 9 and newer compilers
recordmcount.pl is not used anymore.
- Remove preempt_disable()/preempt_enable() pair in
kprobe_ftrace_handler() which was done for all architectures except
for s390.
- Update defconfig
* tag 's390-5.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
recordmcount.pl: look for jgnop instruction as well as bcrl on s390
s390/entry: fix duplicate tracking of irq nesting level
s390: enable switchdev support in defconfig
s390/kexec: handle R_390_PLT32DBL rela in arch_kexec_apply_relocations_add()
s390/ftrace: remove preempt_disable()/preempt_enable() pair
s390/kexec_file: fix error handling when applying relocations
s390/kexec_file: print some more error messages
If I created a kunitconfig file that was incomplete, then
$ ./tools/testing/kunit/kunit.py build --kunitconfig=my_kunitconfig
would silently drop all the options with unmet dependencies!
This is because it doesn't do the config check that `kunit.py config`
does.
So if I want to safely build a kernel for testing, I have to do
$ ./tools/testing/kunit/kunit.py config <flags>
$ ./tools/testing/kunit/kunit.py build <flags, again>
It seems unlikely that any user of kunit.py would want the current
`build` semantics.
So make it effectively do `kunit.py config` + `kunit.py build`.
Signed-off-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The `log` field is unused, and the `status` field is accessible via
`test.status`.
So it's simpler to just return the main `Test` object directly.
And since we're no longer returning a namedtuple, which has no type
annotations, this hopefully means typecheckers are better equipped to
find any errors.
Signed-off-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
namedtuple is a terse way of defining a collection of fields.
However, it does not allow us to annotate the type of these fields.
It also doesn't let us have any sort of inheritance between types.
Since commit df4b0807ca ("kunit: tool: Assert the version
requirement"), kunit.py has asserted that it's running on python >=3.7.
So in that case use a 3.7 feature, dataclasses, to replace these.
Changes in detail:
* Make KunitExecRequest contain all the fields needed for exec_tests
* Use inheritance to dedupe fields
* also allows us to e.g. pass a KUnitRequest in as a KUnitParseRequest
* this has changed around the order of some fields
* Use named arguments when constructing all request objects in kunit.py
* This is to prevent accidentally mixing up fields, etc.
Signed-off-by: Daniel Latypov <dlatypov@google.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Pull hyperv fix from Wei Liu:
"Build fix from Randy Dunlap"
* tag 'hyperv-fixes-signed-20211214' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: utils: add PTP_1588_CLOCK to Kconfig to fix build
Downstream patch will use this bit in order to know whether the device
supports changing of max_uc_list.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
If the audit daemon were ever to get stuck in a stopped state the
kernel's kauditd_thread() could get blocked attempting to send audit
records to the userspace audit daemon. With the kernel thread
blocked it is possible that the audit queue could grow unbounded as
certain audit record generating events must be exempt from the queue
limits else the system enter a deadlock state.
This patch resolves this problem by lowering the kernel thread's
socket sending timeout from MAX_SCHEDULE_TIMEOUT to HZ/10 and tweaks
the kauditd_send_queue() function to better manage the various audit
queues when connection problems occur between the kernel and the
audit daemon. With this patch, the backlog may temporarily grow
beyond the defined limits when the audit daemon is stopped and the
system is under heavy audit pressure, but kauditd_thread() will
continue to make progress and drain the queues as it would for other
connection problems. For example, with the audit daemon put into a
stopped state and the system configured to audit every syscall it
was still possible to shutdown the system without a kernel panic,
deadlock, etc.; granted, the system was slow to shutdown but that is
to be expected given the extreme pressure of recording every syscall.
The timeout value of HZ/10 was chosen primarily through
experimentation and this developer's "gut feeling". There is likely
no one perfect value, but as this scenario is limited in scope (root
privileges would be needed to send SIGSTOP to the audit daemon), it
is likely not worth exposing this as a tunable at present. This can
always be done at a later date if it proves necessary.
Cc: stable@vger.kernel.org
Fixes: 5b52330bbf ("audit: fix auditd/kernel connection state tracking")
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Due to the audit control mutex necessary for serializing audit
userspace messages we haven't been able to block/penalize userspace
processes that attempt to send audit records while the system is
under audit pressure. The result is that privileged userspace
applications have a priority boost with respect to audit as they are
not bound by the same audit queue throttling as the other tasks on
the system.
This patch attempts to restore some balance to the system when under
audit pressure by blocking these privileged userspace tasks after
they have finished their audit processing, and dropped the audit
control mutex, but before they return to userspace.
Reported-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Tested-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11 ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Fix that up by only checking the single bit.
Fixes: 153a2d7e33 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel gained a new interface for drivers to use to combine tail
bump (doorbell) and BQL updates, attempt to use those new interfaces.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver had comments to the effect of: This flag should be set before
calling this function. While reviewing code it was found that there were
several violations of this policy, which could introduce hard to find
bugs or races.
Fix the violations of the "VSI DOWN state must be set before calling
ice_down" and make checking the state into code with a WARN_ON.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The kernel provides some prefetch mechanisms to speed up commonly
cold cache line accesses during receive processing. Since these are
software structures it helps to have these strategically placed
prefetches.
Be careful to call BQL prefetch complete only for non XDP queues.
Co-developed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
During probe and device reset, the ice driver reads some data from the
NVM image as part of ice_init_nvm. Part of this data includes a section
of the Option ROM which contains version information.
The function ice_get_orom_civd_data is used to locate the '$CIV' data
section of the Option ROM.
Timing of ice_probe and ice_rebuild indicate that the
ice_get_orom_civd_data function takes about 10 seconds to finish
executing.
The function locates the section by scanning the Option ROM every 512
bytes. This requires a significant number of NVM read accesses, since
the Option ROM bank is 500KB. In the worst case it would take about 1000
reads. Worse, all PFs serialize this operation during reload because of
acquiring the NVM semaphore.
The CIVD section is located at the end of the Option ROM image data.
Unfortunately, the driver has no easy method to determine the offset
manually. Practical experiments have shown that the data could be at
a variety of locations, so simply reversing the scanning order is not
sufficient to reduce the overall read time.
Instead, copy the entire contents of the Option ROM into memory. This
allows reading the data using 4Kb pages instead of 512 bytes at a time.
This reduces the total number of firmware commands by a factor of 8. In
addition, reading the whole section together at once allows better
indication to firmware of when we're "done".
Re-write ice_get_orom_civd_data to allocate virtual memory to store the
Option ROM data. Copy the entire OptionROM contents at once using
ice_read_flash_module. Finally, use this memory copy to scan for the
'$CIV' section.
This change significantly reduces the time to read the Option ROM CIVD
section from ~10 seconds down to ~1 second. This has a significant
impact on the total time to complete a driver rebuild or probe.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_devlink_flash_update function performs a few upfront checks and
then calls ice_flash_pldm_image.
Most if these checks make more sense in the context of code within
ice_flash_pldm_image. Merge ice_devlink_flash_update and
ice_flash_pldm_image into one function, placing it in ice_fw_update.c
Since this is still the entry point for devlink, call the function
ice_devlink_flash_update instead of ice_flash_pldm_image. This leaves a
single function which handles the devlink parameters and then initiates
a PLDM update.
With this change, the ice_devlink_flash_update function in
ice_fw_update.c becomes the main entry point for flash update. It
elimintes some unnecessary boiler plate code between the two previous
functions. The ultimate motivation for this is that it eases supporting
a dry run with the PLDM library in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_devlink_flash_update function performs a few checks and then
calls ice_flash_pldm_image. One of these checks is to call
ice_check_for_pending_update. This function checks if the device has
a pending update, and cancels it if so. This is necessary to allow
a new flash update to proceed.
We want to refactor the ice code to eliminate ice_devlink_flash_update,
moving its checks into ice_flash_pldm_image.
To do this, ice_check_for_pending_update will become static, and only
called by ice_flash_pldm_image. To make this change easier to review,
first just move the function up within the ice_fw_update.c file.
While at it, note that the function has a misleading name. Its primary
action is to cancel a pending update. Using the verb "check" does not
imply this. Rename it to ice_cancel_pending_update.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We have a region for reading the contents of the NVM flash as
a snapshot. This region does not allow reading the Shadow RAM, as it
always passes the FLASH_ONLY bit to the low level firmware interface.
Add a separate shadow-ram region which will allow snapshot of the
current contents of the Shadow RAM. This data is built from the NVM
contents but is distinct as the device builds up the Shadow RAM during
initialization, so being able to snapshot its contents can be useful
when attempting to debug flash related issues.
Fix the comment description of the nvm-flash region which incorrectly
stated that it filled the shadow-ram region, and add a comment
explaining that the nvm-flash region does not actually read the Shadow
RAM.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make Nexus 7 device-tree to use common LVDS bridge description. This makes
device-trees more consistent.
[digetx@gmail.com: factored Nexus7 change into separate patch and wrote commit message]
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
CPU of Nyan Chromebooks is overheating badly because apparently hardware
soctherm controller doesn't work well. Add CPU thermal zones to enable
software thermal control over CPU and fix the overheat trouble.
Tested-by: Thomas Graichen <thomas.graichen@gmail.com> # T124 Nyan Big
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable CPU DFLL node on Nyan Chromebooks. DFLL was previously disabled due
to Linux kernel CPUFreq driver which didn't support suspend-resume. That
problem was fixed years ago, but DFLL was never re-enabled.
Tested-by: Thomas Graichen <thomas.graichen@gmail.com> # T124 Nyan Big
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If an USB port is an OTG port, then we should add the usb-role-switch
property. Otherwise XUSB setup fails and therefore padctl is unable to
set up the ports. This leads to broken USB and PCIe ports. Add the
usb-role-switch properties to Tegra124 device-trees to fix the problem.
The error message shown without this patch is e.g:
usb2-0: usb-role-switch not found for otg mode
[digetx@gmail.com: improved commit message]
Tested-by: Thomas Graichen <thomas.graichen@gmail.com> # T124 Nyan Big
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add dedicated device-tree for 1080p version of Nyan Big in order to
describe display panel properly. FHD panel doesn't support modes other
than 1080p, hence it's wrong to use incompatible lower resolution panel
in device-tree.
Tested-by: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
