Pull RAS/CMCI storm code fix from Tony Luck:
"Fix the code to tell when a CMCI storm ends by actually
looking at the machine check banks when we poll while
interrupts are disabled."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A change introduced with commit 60283df7ac
("x86/apic: Read Error Status Register correctly") removed a read from the
APIC ESR register made before writing to same required to retrieve the
correct error status on Pentium systems affected by the 3AP erratum[1]:
"3AP. Writes to Error Register Clears Register
PROBLEM: The APIC Error register is intended to only be read.
If there is a write to this register the data in the APIC Error
register will be cleared and lost.
IMPLICATION: There is a possibility of clearing the Error
register status since the write to the register is not
specifically blocked.
WORKAROUND: Writes should not occur to the Pentium processor
APIC Error register.
STATUS: For the steppings affected see the Summary Table of
Changes at the beginning of this section."
The steppings affected are actually: B1, B3 and B5.
To avoid this information loss this change avoids the write to
ESR on all Pentium systems where it is actually never needed;
in Pentium processor documentation ESR was noted read-only and
the write only required for future architectural
compatibility[2].
The approach taken is the same as in lapic_setup_esr().
References:
[1] "Pentium Processor Family Developer's Manual", Intel Corporation,
1997, order number 241428-005, Appendix A "Errata and S-Specs for the
Pentium Processor Family", p. A-92,
[2] "Pentium Processor Family Developer's Manual, Volume 3: Architecture
and Programming Manual", Intel Corporation, 1995, order number
241430-004, Section 19.3.3. "Error Handling In APIC", p. 19-33.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Richard Weinberger <richard@nod.at>
Link: http://lkml.kernel.org/r/alpine.LFD.2.11.1404011300010.27402@eddie.linux-mips.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The table is never modified and all OF functions that use it take a
const struct of_device_id *.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This reverts commit 8468949cdd.
The OF match table dummy for non-OF configurations cannot be removed
because it is still used by the pxa_pwm_get_id_dt() function.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a device tree match table. This serves to make the driver's support
of device tree more explicit. Perhaps the fallback for DT matching to
using the i2c_device_id table will go away one day, since it fails in
face of devices from different vendors with the same name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
alc5632_probe() returns ret, yet it is not initialized or set anywhere.
This ends up causing the function to appear to fail, and audio not to
work on the Toshiba AC100, with my compiler at least.
This function used to set ret in all cases, but recent cleanup removed
that.
Fixes: 5d6be5aa6b ("ASoC: codec: Simplify ASoC probe code.")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a timeout option for queued requests and introduces
sclp_sync_request_timeout() to use this timer. With this, blocking the
system too long, e.g. during an SE reboot, can be avoided in critical
situations like CPU and memory hotplug.
Since there is no way to cancel a running request, this timeout only
applies to queued requests that have not yet been started.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It need to add curly braces because the inner for "if" has
two statements.
coccicheck says:
drivers/base/regmap/regmap.c:765:2-44:
code aligned with following code on line 766
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As time goes, the code changes a lot, and this leads to that
some old-days comments scatter around , which instead of faciliating
understanding, but make more confusion. So this patch cleans up them.
Also, this patch unifies some variables naming.
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jianyu Zhan <nasa4836@gmail.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
commit 'slab: restrict the number of objects in a slab' uses
__builtin_constant_p() on #if macro. It is wrong usage of builtin
function, but it is compiled on x86 without any problem, so I can't
find it before 0 day build system find it.
This commit fixes the situation by using KMALLOC_MIN_SIZE, instead of
KMALLOC_SHIFT_LOW. KMALLOC_SHIFT_LOW is parsed to ilog2() on some
architecture and this ilog2() uses __builtin_constant_p() and results in
the problem. This problem would disappear by using KMALLOC_MIN_SIZE,
since it is just constant.
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
There is no point to toggle the RX led for every packet. Especially if
we have a full FIFO we want to avoid everything we can.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function loads the message object from the hardware to get the
payload length. The previous patch stores that information in an
array, so we can avoid the hardware access.
Remove the hardware access and move the led toggle outside of the
spinlocked region. Toggle the led only once when at least one packet
has been received.
Binary size shrinks along with the code
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We can avoid the HW access in TX cleanup path for retrieving the DLC
of the sent package if we store the DLC in a private array.
Ideally this should be handled in the can_echo_skb functions, but I
leave that exercise to the CAN folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
commit 4ce78a838c (can: c_can: Speed up rx_poll function) hyped a
performance improvement by reducing the access to the interrupt
pending register from a dual 16 bit to a single 16 bit access. Wow!
Thereby it crippled the driver to cast the 16 msg objects in stone,
which is completly braindead as contemporary hardware has up to 128
message objects. Supporting larger object buffers is a major surgery,
but it'd be definitely worth it especially as the driver does not
support HW message filtering ....
The logic of the "FIFO" implementation is to split the FIFO in half.
For the lower half we read the buffers and clear the interrupt pending
bit, but keep the newdat bit set, so the HW will queue above those
buffers.
When we read out the last low buffer then we reenable all the low half
buffers by clearing the newdat bit.
The upper half buffers clear the newdat and the interrupt pending bit
right away as we know that the lower half bits are clear and give us a
headstart against the hardware.
Now the implementation is:
transfer_message_object()
read_object_and_put_into_skb();
if (obj < END_OF_LOW_BUF)
clear_intpending(obj)
else if (obj > END_OF_LOW_BUF)
clear_intpending_and_newdat(obj)
else if (obj == END_OF_LOW_BUF)
clear_newdat_of_all_low_objects()
The hardware allows to avoid most of the mess simply because we can
tell the transfer_message_object() function to clear bits right away.
So we can be clever and do:
if (obj <= END_OF_LOW_BUF)
ctrl = TRANSFER_MSG | CLEAR_INTPND;
else
ctrl = TRANSFER_MSG | CLEAR_INTPND | CLEAR_NEWDAT;
transfer_message_object(ctrl)
read_object_and_put_into_skb();
if (obj == END_OF_LOW_BUF)
clear_newdat_of_all_low_objects()
So we save a complete control operation on all message objects except
the one which is the end of the low buffer. That's a few micro seconds
per object.
I'm not adding a boasting profile to that, simply because it's self
explaining.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If every other line contains line breaks, that's a clear sign for
indentation level madness. Split out the inner loop and move the code
to a separate function. gcc creates slightly worse code for that, but
we'll fix that in the next step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The network core does not serialize the access to the hardware. The
xmit related code lets the following happen:
CPU0 CPU1
interrupt()
do_poll()
c_can_do_tx()
Fiddle with HW and xmit()
internal data Fiddle with HW and
internal data
due the complete lack of serialization.
Add proper locking.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The rx_poll code has the following gem:
if (msg_ctrl_save & IF_MCONT_EOB)
return num_rx_pkts;
The EOB bit is the indicator for the hardware that this is the last
configured FIFO object. But this object can contain valid data, if we
manage to free up objects before the overrun case hits.
Now if the code exits due to the EOB bit set, then this buffer is
stale and the interrupt bit and NewDat bit of the buffer are still
set. Results in a nice interrupt storm unless we come into an overrun
situation where the MSGLST bit gets set.
ksoftirqd/0-3 [000] ..s. 79.124101: c_can_poll: rx_poll: val: 00008001 pend 00008001
ksoftirqd/0-3 [000] ..s. 79.124176: c_can_poll: rx_poll: val: 00008000 pend 00008000
ksoftirqd/0-3 [000] ..s. 79.124187: c_can_poll: rx_poll: val: 00008002 pend 00008002
ksoftirqd/0-3 [000] ..s. 79.124256: c_can_poll: rx_poll: val: 00008000 pend 00008000
ksoftirqd/0-3 [000] ..s. 79.124267: c_can_poll: rx_poll: val: 00008000 pend 00008000
The amazing thing is that the check of the MSGLST (aka overrun bit)
used to be after the check of the EOB bit. That was "fixed" in commit
5d0f801a2c(can: c_can: Fix RX message handling, handle lost message
before EOB). But the author of this "fix" did not even understand that
the EOB check is broken as well.
Again a simple solution: Remove
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The lost message handling is broken in several ways.
1) Clearing the message lost flag is done by writing 0 to the
message control register of the object.
#define IF_MCONT_CLR_MSGLST (0 << 14)
That clears the object buffer configuration in the worst case,
which results in a loss of the EOB flag. That leaves the FIFO chain
without a limit and causes a complete lockup of the HW
2) In case that the error skb allocation fails, the code happily
claims that it handed down a packet. Just an accounting bug, but ....
3) The code adds a lot of pointless overhead to that error case, where
we need to get stuff done as fast as possible to avoid more packet
loss.
- printk an annoying error message
- reread the object buffer for nothing
Fix is simple again:
- Use the already known MSGCTRL content and only clear the MSGLST bit
- Fix the buffer accounting by adding a proper return code
- Remove the pointless operations
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The buffer handling of c_can has been broken forever. That leads to
message reordering:
ksoftirqd/0-3 [000] ..s. 79.123776: c_can_poll: rx_poll: val: 00007fff
ksoftirqd/0-3 [000] ..s. 79.124101: c_can_poll: rx_poll: val: 00008001
What happens is:
CPU HW
queue new packet into obj 16 (0-15 are busy)
read obj 1-15
return because pending is 0
set pending obj 16 -> pending reg 8000
queue new packet into obj 1
set pending obj 1 -> pending reg 8001
So the current algorithmus reads the newest message first, which
violates the ordering rules of CAN.
Add proper handling of that situation by analyzing the contents of the
pending register for gaps.
This does NOT fix the message object corruption which can lead to
interrupt storms. Thats addressed in the next patches.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The hardware has two message control interfaces, but the code only uses the
first one. So on SMP the following can be observed:
CPU0 CPU1
rx_poll()
write IF1 xmit()
write IF1
write IF1
That results in corrupted message object configurations. The TX/RX is not
globally serialized it's only serialized on a core.
Simple solution: Let RX use IF1 and TX use IF2 and all is good.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function is broken in several ways:
- The function does not wait for the init to complete.
That can take quite some microseconds.
- No protection against being called for two chips at the same
time. SMP is such a new thing, right?
Clear the start and the init done bit unconditionally and wait for both bits to
be clear.
In the enable path set the init bit and wait for the init done bit.
Add proper locking.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
According to the documentation the CPU must wait for CONTROL_INIT to
be cleared before writing to the baudrate registers.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the name of the parameter to configure the sample point used
in iproute2's ip command. The correct writing is "sample-point" not
"sample_point".
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixed a memory leak when an error occurred in the transmit function. In the
error handling the urb wasn't freed before returning. There was also a call to
the usb_unanchor_urb() function but the urb wasn't anchored.
Signed-off-by: Bjorn Van Tilt <bjorn.vantilt@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In f2fs_setxattr we have limit this attribute name length, so we should also
check it in f2fs_getxattr to avoid useless lookup caused by invalid name length.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch introduce is_merged_page() to check whether current page is merged
in f2fs bio cache. When page is not in cache, we can avoid submitting bio cache,
resulting in having more chance to merge pages.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The GHASH setkey() function uses SSE registers but fails to call
kernel_fpu_begin()/kernel_fpu_end(). Instead of adding these calls, and
then having to deal with the restriction that they cannot be called from
interrupt context, move the setkey() implementation to the C domain.
Note that setkey() does not use any particular SSE features and is not
expected to become a performance bottleneck.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Fixes: 0e1227d356 (crypto: ghash - Add PCLMULQDQ accelerated implementation)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The commit ec3fadd64b (kbuild: docbook: use $(obj) and $(src) rather
than specific path) replaces the specific path with $(src). But when
executing "make help", the $(src) is null and then causes an include
error. Fix it by restoring the specific path.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
During the cleaing of node segments, F2FS can get errored node blocks due to
data race between node page lock and its valid bitmap operations.
In that case, it needs to return an error to skip such the obsolete block copy.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We need to reset the usage state of the pages on kexec/kdump,
which use subcode 0 and 1. We will only do the cmma reset in
the kernel, everything else is done in userspace as before.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
del_timer() does not wait for a possible running callback to
complete. So the call side might free request and the associated
objects while on another cpu the timer handler runs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the 3270 device is detached the initial reset device request will
stays pending until the device is operational. A second reset device
call will reuse the same request structure which will cause an oops.
Add a check to see if the reset device request is already pending
and do nothing in this case.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When reworking the bitops and atomic ops I missed that those instructions
that got atomic behaviour only perform a "specific-operand-serialization"
instead of a full "serialization".
The compare-and-swap instruction used before performs a full serialization
before and after the instruction is executed, which means it has full
memory barrier semantics.
In order to give the new bitops and atomic ops functions also full memory
barrier semantics add a "bcr 14,0" before and after each of those new
instructions which performs full serialization as well.
This restores memory barrier semantics for bitops and atomic ops functions
which return values, like e.g. atomic_add_return(), but not for functions
which do not return a value, like e.g. atomic_add().
This is consistent to other architectures and what common code requires.
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently in ext4_fallocate() and ext4_zero_range() we're testing ret
variable along with new_size. However in ext4_fallocate() we just tested
ret before and in ext4_zero_range() if will always be zero when we get
there so there is no need to test it in both cases.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
It uses the unnecessary S_IFREG bit which broke when my
stricter-checking-for-mode patch went in.
Since we're fixing it anyway, the extra level of indirection is
confusing for readers (ROOT_W == rw-r--r-- for example).
Also, many of these are other-writable. Is that really intended?
I'll-queue-this-patch-up-in-a-bit-by: Greg KH <greg@kroah.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains fixes to e1000e, igb, ixgbe, ixgebvf, i40e and
i40evf.
David provides a fix for e1000e to resolve an issue where the device is
capable of transmitting packets but is unable to receive packets until
a previously introduced workaround is called.
Jakub Kicinski provides PTP fixes for ixgbe, which include removing a
redundant if clause and make sure we are not generating both a software and
hardware timestamp. As well as fix a race condition and leaking skbs
when multiple transmit rings try to claim time stamping.
Jean Sacren fixes a function declaration in ixgbe which was introduced
in commit c97506ab0e ("ixgbe: Add check for FW veto bit"). In addition
fixes a function header comment in i40e and fixes the error checking
by binding the check to the pertinent DMA bit mask.
Mark provides several fixes for ixgbe and ixgbevf. Most notably are fixes
to resolve namespace issues and fix ECU warnings induced by LER for ixgbe
and ixgbevf.
Joe Perches fixes up unnecessary casts in i40e and i40evf.
Peter Senna Tschudin fixes igb to use pci_iounmap when the virtual mapping
was done with pci_iomap.
====================# Please enter a commit message to explain why this merge is necessary,
The clock generator for rcar-gen2 has the lb, sdh, sd0 and sd1 clocks
parented to pll1_div2 where the hardware diagram shows these to be
directly fed from pll1.
This fixes the initial rate for sdh0 clock to be 97.5MHz instead of
the reported 48MHz where the manual says the default register values
are for 97.5MHz.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Resolve some rcu warnings produced when LER actions take place.
This appears to be due to not holding the rtnl lock when calling
ixgbe_down, so hold the lock. Also avoid disabling the device
when it is already disabled. This check is necessary because the
callback can be called more than once in some cases.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve some rcu warnings produced when LER actions take place.
This appears to be due to not holding the rtnl lock when calling
ixgbe_down, so hold the lock. Also avoid disabling the device
when it is already disabled. This check is necessary because the
callback can be called more than once in some cases.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
