This patch adds support for ColdFire mcf5441x-family edma
module.
The ColdFire edma module is slightly different from fsl-edma,
so a new driver is added. But most of the code is common
between fsl-edma and mcf-edma so it has been collected into a
separate common module fsl-edma-common (patch 1/3).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merge tag 'gvt-next-2018-09-04'
drm-intel-next-2018-09-06-1:
UAPI Changes:
- GGTT coherency GETPARAM: GGTT has turned out to be non-coherent for some
platforms, which we've failed to communicate to userspace so far. SNA was
modified to do extra flushing on non-coherent GGTT access, while Mesa will
mitigate by always requiring WC mapping (which is non-coherent anyway).
- Neuter Resource Streamer uAPI: There never really were users for the feature,
so neuter it while keeping the interface bits for compatibility. This is a
long due item from past.
Cross-subsystem Changes:
- Backmerge of branch drm-next-4.19 for DP_DPCD_REV_14 changes
Core Changes:
- None
Driver Changes:
- A load of Icelake (ICL) enabling patches (Paulo, Manasi)
- Enabled full PPGTT for IVB,VLV and HSW (Chris)
- Bugzilla #107113: Distribute DDB based on display resolutions (Mahesh)
- Bugzillas #100023,#107476,#94921: Support limited range DP displays (Jani)
- Bugzilla #107503: Increase LSPCON timeout (Fredrik)
- Avoid boosting GPU due to an occasional stall in interactive workloads (Chris)
- Apply GGTT coherency W/A only for affected systems instead of all (Chris)
- Fix for infinite link training loop for faulty USB-C MST hubs (Nathan)
- Keep KMS functional on Gen4 and earlier when GPU is wedged (Chris)
- Stop holding ppGTT reference from closed VMAs (Chris)
- Clear error registers after error capture (Lionel)
- Various Icelake fixes (Anusha, Jyoti, Ville, Tvrtko)
- Add missing Coffeelake (CFL) PCI IDs (Rodrigo)
- Flush execlists tasklet directly from reset-finish (Chris)
- Fix LPE audio runtime PM (Chris)
- Fix detection of out of range surface positions (GLK/CNL) (Ville)
- Remove wait-for-idle for PSR2 (Dhinakaran)
- Power down existing display hardware resources when display is disabled (Chris)
- Don't allow runtime power management if RC6 doesn't exist (Chris)
- Add debugging checks for runtime power management paths (Imre)
- Increase symmetry in display power init/fini paths (Imre)
- Isolate GVT specific macros from i915_reg.h (Lucas)
- Increase symmetry in power management enable/disable paths (Chris)
- Increase IP disable timeout to 100 ms to avoid DRM_ERROR (Imre)
- Fix memory leak from HDMI HDCP write function (Brian, Rodrigo)
- Reject Y/Yf tiling on interlaced modes (Ville)
- Use a cached mapping for the physical HWS on older gens (Chris)
- Force slow path of writing relocations to buffer if unable to write to userspace (Chris)
- Do a full device reset after being wedged (Chris)
- Keep forcewake counts over reset (in case of debugfs user) (Imre, Chris)
- Avoid false-positive errors from power wells during init (Imre)
- Reset engines forcibly in exchange of declaring whole device wedged (Mika)
- Reduce context HW ID lifetime in preparation for Icelake (Chris)
- Attempt to recover from module load failures (Chris)
- Keep select interrupts over a reset to avoid missing/losing them (Chris)
- GuC submission backend improvements (Jakub)
- Terminate context images with BB_END (Chris, Lionel)
- Make GCC evaluate GGTT view struct size assertions again (Ville)
- Add selftest to exercise suspend/hibernate code-paths for GEM (Chris)
- Use a full emulation of a user ppgtt context in selftests (Chris)
- Exercise resetting in the middle of a wait-on-fence in selftests (Chris)
- Fix coherency issues on selftests for Baytrail (Chris)
- Various other GEM fixes / self-test updates (Chris, Matt)
- GuC doorbell self-tests (Daniele)
- PSR mode control through debugfs for IGTs (Maarten)
- Degrade expected WM latency errors to DRM_DEBUG_KMS (Chris)
- Cope with errors better in MST link training (Dhinakaran)
- Fix WARN on KBL external displays (Azhar)
- Power well code cleanups (Imre)
- Fixes to PSR debugging (Dhinakaran)
- Make forcewake errors louder for easier catching in CI (WARNs) (Chris)
- Fortify tiling code against programmer errors (Chris)
- Bunch of fixes for CI exposed corner cases (multiple authors, mostly Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907105446.GA22860@jlahtine-desk.ger.corp.intel.com
Change flower in_hw_count type to fixed-size u32 and dump it as
TCA_FLOWER_IN_HW_COUNT. This change is necessary to properly test shared
blocks and re-offload functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It documents what is happening, and eliminates the spurious list
pointer poisoning.
In the long term, in order to get proper list head debugging, we
might want to use the list poison value as the indicator that
an SKB is a singleton and not on a list.
Signed-off-by: David S. Miller <davem@davemloft.net>
An SKB is not on a list if skb->next is NULL.
Codify this convention into a helper function and use it
where we are dequeueing an SKB and need to mark it as such.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, adjust __qdisc_enqueue_tail() such that HTB can use it
instead.
The only other caller of __qdisc_enqueue_tail() is
qdisc_enqueue_tail() so we can move the backlog and return value
handling (which HTB doesn't need/want) to the latter.
Signed-off-by: David S. Miller <davem@davemloft.net>
After the conversion to fib6_info, rt6i_prefsrc has a single user that
reads the value and otherwise it is only set. The one reader can be
converted to use rt->from so rt6i_prefsrc can be removed, reducing
rt6_info by another 20 bytes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCMI protocol can be used to get power estimates from firmware
corresponding to each performance state of a device. Although these power
costs are already managed by the SCMI firmware driver, they are not
exposed to any external subsystem yet.
Fix this by adding a new get_power() interface to the exisiting perf_ops
defined for the SCMI protocol.
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit 1c892e38ce ("regulator: da9063: Handle less LDOs on DA9063L")
reordered the da9063_regulator_info[] array, but not the DA9063_ID_*
regulator ids and not the da9063_matches[] array, because ids are used
as indices in the array initializer. This mismatch between regulator id
and da9063_regulator_info[] array index causes the driver probe to fail
because constraints from DT are not applied to the correct regulator:
da9063 0-0058: Device detected (chip-ID: 0x61, var-ID: 0x50)
DA9063_BMEM: Bringing 900000uV into 3300000-3300000uV
DA9063_LDO9: Bringing 3300000uV into 2500000-2500000uV
DA9063_LDO1: Bringing 900000uV into 3300000-3300000uV
DA9063_LDO1: failed to apply 3300000-3300000uV constraint(-22)
This patch reorders the DA9063_ID_* as apparently intended, and with
them the entries in the da90630_matches[] array.
Fixes: 1c892e38ce ("regulator: da9063: Handle less LDOs on DA9063L")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Put the pointer to struct regmap_irq_chip_data into the parent
mfd structure so that the child irqchip driver does not need
a trivial private structure to store only this pointer. As
the irqchip child driver already has a pointer to the parent
struct madera it can use that to store the pointer. This also
means that the irqchip driver does not need a double-indirection
from its local struct to get at the parent struct madera.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There would be useful to have in future the similar API in platform
core, as we have, for example, for PCI subsystem, to check if device
belongs to it.
Thus, split out conditional to a macro dev_is_platform() for wide use.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, when a reader acquires a lock, it only sets the
RWSEM_READER_OWNED bit in the owner field. The other bits are simply
not used. When debugging hanging cases involving rwsems and readers,
the owner value does not provide much useful information at all.
This patch modifies the current behavior to always store the task_struct
pointer of the last rwsem-acquiring reader in a reader-owned rwsem. This
may be useful in debugging rwsem hanging cases especially if only one
reader is involved. However, the task in the owner field may not the
real owner or one of the real owners at all when the owner value is
examined, for example, in a crash dump. So it is just an additional
hint about the past history.
If CONFIG_DEBUG_RWSEMS=y is enabled, the owner field will be checked at
unlock time too to make sure the task pointer value is valid. That does
have a slight performance cost and so is only enabled as part of that
debug option.
From the performance point of view, it is expected that the changes
shouldn't have any noticeable performance impact. A rwsem microbenchmark
(with 48 worker threads and 1:1 reader/writer ratio) was ran on a
2-socket 24-core 48-thread Haswell system. The locking rates on a
4.19-rc1 based kernel were as follows:
1) Unpatched kernel: 543.3 kops/s
2) Patched kernel: 549.2 kops/s
3) Patched kernel (CONFIG_DEBUG_RWSEMS on): 546.6 kops/s
There was actually a slight increase in performance (1.1%) in this
particular case. Maybe it was caused by the elimination of a branch or
just a testing noise. Turning on the CONFIG_DEBUG_RWSEMS option also
had less than the expected impact on performance.
The least significant 2 bits of the owner value are now used to designate
the rwsem is readers owned and the owners are anonymous.
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/1536265114-10842-1-git-send-email-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The SD_ASYM_CPUCAPACITY sched_domain flag is supposed to mark the
sched_domain in the hierarchy where all CPU capacities are visible for
any CPU's point of view on asymmetric CPU capacity systems. The
scheduler can then take to take capacity asymmetry into account when
balancing at this level. It also serves as an indicator for how wide
task placement heuristics have to search to consider all available CPU
capacities as asymmetric systems might often appear symmetric at
smallest level(s) of the sched_domain hierarchy.
The flag has been around for while but so far only been set by
out-of-tree code in Android kernels. One solution is to let each
architecture provide the flag through a custom sched_domain topology
array and associated mask and flag functions. However,
SD_ASYM_CPUCAPACITY is special in the sense that it depends on the
capacity and presence of all CPUs in the system, i.e. when hotplugging
all CPUs out except those with one particular CPU capacity the flag
should disappear even if the sched_domains don't collapse. Similarly,
the flag is affected by cpusets where load-balancing is turned off.
Detecting when the flags should be set therefore depends not only on
topology information but also the cpuset configuration and hotplug
state. The arch code doesn't have easy access to the cpuset
configuration.
Instead, this patch implements the flag detection in generic code where
cpusets and hotplug state is already taken care of. All the arch is
responsible for is to implement arch_scale_cpu_capacity() and force a
full rebuild of the sched_domain hierarchy if capacities are updated,
e.g. later in the boot process when cpufreq has initialized.
Signed-off-by: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dietmar.eggemann@arm.com
Cc: valentin.schneider@arm.com
Cc: vincent.guittot@linaro.org
Link: http://lkml.kernel.org/r/1532093554-30504-2-git-send-email-morten.rasmussen@arm.com
[ Fixed 'CPU' capitalization. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When using the gpiolib irqchip helpers install irq_enable/disable
hooks for the irqchip to ensure that gpiolib knows when the irq
is enabled or disabled, allowing drivers to disable the irq and then
use it as an output pin, and later switch the direction to input and
re-enable the irq.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO drivers call gpiochip_(un)lock_as_irq whenever they want to use a gpio
as an interrupt. This is done when the irq is requested and it marks the
gpio as in use by an interrupt.
This is problematic for cases where a gpio pin is used as an interrupt
pin, then, after the irq is disabled, is used as a regular gpio pin.
Currently it is not possible to do this other than by first freeing
the interrupt so gpiochip_unlock_as_irq is called, since an attempt to
switch the gpio direction for output will fail since gpiolib believes
that the gpio is in use for an interrupt and it does not know that it
the irq is actually disabled.
There are currently two drivers that would like to be able to do this:
the tda998x_drv.c driver where a regular gpio pin needs to be temporarily
reconfigured as an interrupt pin during CEC calibration, and the cec-gpio
driver where you want to configure the gpio pin as an interrupt while
waiting for traffic over the CEC bus, or as a regular pin when receiving or
transmitting a CEC message.
The solution is to add a new flag that is set when the irq is enabled,
and have gpiod_direction_output check for that flag.
We also add functions that drivers that do not use GPIOLIB_IRQCHIP
can call when they enable/disable the irq.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO drivers that do not use GPIOLIB_IRQCHIP can hook these into
the irq_request_resource and irq_release_resource callbacks of the
irq_chip so they correctly 'get' the module and lock the gpio line
for IRQ use.
This will simplify driver code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull timekeeping fixes from Thomas Gleixner:
"Two fixes for timekeeping:
- Revert to the previous kthread based update, which is unfortunately
required due to lock ordering issues. The removal caused boot
failures on old Core2 machines. Add a proper comment why the thread
needs to stay to prevent accidental removal in the future.
- Fix a silly typo in a function declaration"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Revert "Remove kthread"
timekeeping: Fix declaration of read_persistent_wall_and_boot_offset()
There is no reason to leave the per-device dma_ops around when
deconfiguring a device, so move this code from arm64 into the
common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
This goes through a lot of hooks just to call arch_teardown_dma_ops.
Replace it with a direct call instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
There is no good reason for this indirection given that the method
always exists.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
To avoid use-after-free(s), use a refcount to keep track of the
usable references to any instantiated struct p9_req_t.
This commit adds p9_req_put(), p9_req_get() and p9_req_try_get() as
wrappers to kref_put(), kref_get() and kref_get_unless_zero().
These are used by the client and the transports to keep track of
valid requests' references.
p9_free_req() is added back and used as callback by kref_put().
Add SLAB_TYPESAFE_BY_RCU as it ensures that the memory freed by
kmem_cache_free() will not be reused for another type until the rcu
synchronisation period is over, so an address gotten under rcu read
lock is safe to inc_ref() without corrupting random memory while
the lock is held.
Link: http://lkml.kernel.org/r/1535626341-20693-1-git-send-email-asmadeus@codewreck.org
Co-developed-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+467050c1ce275af2a5b8@syzkaller.appspotmail.com
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Having a specific cache for the fcall allocations helps speed up
end-to-end latency.
The caches will automatically be merged if there are multiple caches
of items with the same size so we do not need to try to share a cache
between different clients of the same size.
Since the msize is negotiated with the server, only allocate the cache
after that negotiation has happened - previous allocations or
allocations of different sizes (e.g. zero-copy fcall) are made with
kmalloc directly.
Some figures on two beefy VMs with Connect-IB (sriov) / trans=rdma,
with ior running 32 processes in parallel doing small 32 bytes IOs:
- no alloc (4.18-rc7 request cache): 65.4k req/s
- non-power of two alloc, no patch: 61.6k req/s
- power of two alloc, no patch: 62.2k req/s
- non-power of two alloc, with patch: 64.7k req/s
- power of two alloc, with patch: 65.1k req/s
Link: http://lkml.kernel.org/r/1532943263-24378-2-git-send-email-asmadeus@codewreck.org
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Acked-by: Jun Piao <piaojun@huawei.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Greg Kurz <groug@kaod.org>
Only some old OpenFirmware implementations rely on default sizes. Any
FDT and modern implementation should have explicit properties. Make the
OF_ROOT_NODE_*_CELLS_DEFAULT defines private so we don't get any outside
users.
This also gets us one step closer to removing the asm/prom.h dependency on
Sparc.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cros-ec includes inside the MFD subsystem, specially the file
cros_ec_commands.h, has been modified several times and it has grown a
lot, unfortunately, we didn't have care too much about the documentation.
This patch tries to improve the documentation and also fixes all the
issues reported by kerneldoc script.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
The cros-ec-lpc driver lives in drivers/platform because is platform
specific, however there are two includes (cros_ec_lpc_mec.h and
cros_ec_lpc_reg.h) that lives in include/linux/mfd. These two includes
are only used for the platform driver and are not really related to the
MFD subsystem, so move the includes from include/linux/mfd to
drivers/platform/chrome.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
drm-misc-next for 4.20:
UAPI Changes:
- Add userspace dma-buf device to turn memfd regions into dma-bufs (Gerd)
- Add per-plane blend mode property (Lowry)
- Change in drm_fourcc.h is documentation only (Brian)
Cross-subsystem Changes:
- None
Core Changes:
- Remove user logspam and useless lock in vma_offset_mgr destroy (Chris)
- Add get/verify_crc_source for improved crc source selection (Mahesh)
- Add __drm_atomic_helper_plane_reset to reduce copypasta (Alexandru)
Driver Changes:
- various: Replance ref/unref calls with drm_dev_get/put (Thomas)
- bridge: Add driver for TI SN65DSI86 chip (Sandeep)
- rockchip: Add PX30 support (Sandy)
- sun4i: Add support for R40 TCON (Jernej)
- vkms: Continued building out vkms, added gem support (Haneen)Driver Changes:
- various: fbdev: Wrap remove_conflicting_framebuffers with resource_len
accessors to remove a bunch of cargo-cult (Michał)
- rockchip: Add rgb output iface support + fixes (Sandy/Heiko)
- nouveau/amdgpu: Add cec-over-aux support (Hans)
- sun4i: Add support for Allwinner A64 (Jagan)
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905202210.GA95199@art_vandelay
Saeed Mahameed says:
====================
mlx5e-updates-2018-09-05
This series provides updates to mlx5 ethernet driver.
1) Starting with a four patches series to optimize flow counters updates,
From Vlad Buslov:
==============================================
By default mlx5 driver updates cached counters each second. Update function
consumes noticeable amount of CPU resources. The goal of this patch series
is to optimize update function.
Investigation revealed following bottlenecks in fs counters
implementation:
1) Update code(scheduled each second) iterates over all counters twice.
(first for finding and deleting counters that are marked for deletion,
second iteration is for actually updating the counters)
2) Counters are stored in rb tree. Linear iteration over all rb tree
elements(rb_next in profiling data) consumed ~65% of time spent in
update function.
Following optimizations were implemented:
1) Instead of just marking counters for deletion, store them in
standalone list. This removes first iteration over whole counters tree.
2) Store counters in sorted list to optimize traversing them and remove
calls to rb_next.
First implementation of these changes caused degradation of performance,
instead of improving it. Investigation revealed that there first cache
line of struct mlx5_fc is full and adding anything to it causes amount
of cache misses to double. To mitigate that, following refactorings were
implemented:
- Change 'addlist' list type from double linked to single linked. This
allowes to get free space for one additional pointer that is used to
store deletion list(optimization 1)
- Substitute rb tree with idr. Idr is non-intrusive data structure and
doesn't require adding any new members to struct mlx5_fc. Use free
space that became available for double linked sorted list that is used
for traversing all counters. (optimization 2)
Described changes reduced CPU time spent in mlx5_fc_stats_work from 70%
to 44%. (global perf profile mode)
============================================
The rest of the series are misc updates:
2) From Kamal, Move mlx5e_priv_flags into en_ethtool.c, to avoid a
compilation warning.
3) From Roi Dayan, Move Q counters allocation and drop RQ to init_rx profile
function to avoid allocating Q counters when not required.
4) From Shay Agroskin, Replace PTP clock lock from RW lock to seq lock.
Almost double the packet rate when timestamping is active on multiple TX
queues.
5) From: Natali Shechtman, set ECN for received packets using CQE indication.
6) From: Alaa Hleihel, don't set CHECKSUM_COMPLETE on SCTP packets.
CHECKSUM_COMPLETE is not applicable to SCTP protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is pointed that bio_rewind_iter() is one very bad API[1]:
1) bio size may not be restored after rewinding
2) it causes some bogus change, such as 5151842b9d (block: reset
bi_iter.bi_done after splitting bio)
3) rewinding really makes things complicated wrt. bio splitting
4) unnecessary updating of .bi_done in fast path
[1] https://marc.info/?t=153549924200005&r=1&w=2
So this patch takes Kent's suggestion to restore one bio into its original
state via saving bio iterator(struct bvec_iter) in bio_integrity_prep(),
given now bio_rewind_iter() is only used by bio integrity code.
Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Cc: Hannes Reinecke <hare@suse.com>
Suggested-by: Kent Overstreet <kent.overstreet@gmail.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block fixes from Jens Axboe:
"Small collection of fixes that should go into this release. This
contains:
- Small series that fixes a race between blkcg teardown and writeback
(Dennis Zhou)
- Fix disallowing invalid block size settings from the nbd ioctl (me)
- BFQ fix for a use-after-free on last release of a bfqg (Konstantin
Khlebnikov)
- Fix for the "don't warn for flush" fix (Mikulas)"
* tag 'for-linus-20180906' of git://git.kernel.dk/linux-block:
block: bfq: swap puts in bfqg_and_blkg_put
block: don't warn when doing fsync on read-only devices
nbd: don't allow invalid blocksize settings
blkcg: use tryget logic when associating a blkg with a bio
blkcg: delay blkg destruction until after writeback has finished
Revert "blk-throttle: fix race between blkcg_bio_issue_check() and cgroup_rmdir()"
Even though device registration/unregistration and client
registration/unregistration is not a performance path, define the
client_data_lock as rwlock for code clarity.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Pull tracing fixes from Steven Rostedt:
"This fixes two annoying bugs:
- The first one is a side effect caused by using SRCU for rcuidle
tracepoints. It seems that the perf was depending on the rcuidle
tracepoints to make RCU watch when it wasn't.
The real fix will be to have perf use SRCU instead of depending on
RCU watching, but that can't be done until SRCU is safe to use in
NMI context (Paul's working on that).
- The second bug fix is for a bug that's been periodically making my
tests fail randomly for some time. I haven't had time to track it
down, but finally have. It has to do with stressing NMIs (via perf)
while enabling or disabling ftrace function handling with lockdep
enabled.
If an interrupt happens and just as it returns, it sets lockdep
back to "interrupts enabled" but before it returns an NMI is
triggered, and if this happens while printk_nmi_enter has a
breakpoint attached to it (because ftrace is converting it to or
from nop to call fentry), the breakpoint trap also calls into
lockdep, and since returning from the NMI to a interrupt handler,
interrupts were disabled when the NMI went off, lockdep keeps its
state as interrupts disabled when it returns back from the
interrupt handler where interrupts are enabled.
This causes lockdep_assert_irqs_enabled() to trigger a false
positive"
* tag 'trace-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
printk/tracing: Do not trace printk_nmi_enter()
tracing: Add back in rcu_irq_enter/exit_irqson() for rcuidle tracepoints
This patch adds a new qed firmware with fixes and support for new features.
Fixes:
- Fix a rare case of device crash with iWARP, iSCSI or FCoE offload.
- Fix GRE tunneled traffic when iWARP offload is enabled.
- Fix RoCE failure in ib_send_bw when using inline data.
- Fix latency optimization flow for inline WQEs.
- BigBear 100G fix
RDMA:
- Reduce task context size.
- Application page sizes above 2GB support.
- Performance improvements.
ETH:
- Tenant DCB support.
- Replace RSS indirection table update interface.
Misc:
- Debug Tools changes.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
