There is nothing architecture-specific about scs_overflow_check() as
it's just a trivial wrapper around scs_corrupted().
For parity with task_stack_end_corrupted(), rename scs_corrupted() to
task_scs_end_corrupted() and call it from schedule_debug() when
CONFIG_SCHED_STACK_END_CHECK_is enabled, which better reflects its
purpose as a debug feature to catch inadvertent overflow of the SCS.
Finally, remove the unused scs_overflow_check() function entirely.
This has absolutely no impact on architectures that do not support SCS
(currently arm64 only).
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
x18 holds the SCS stack pointer value, so introduce a register alias to
make this easier to read in assembly code.
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Storing the SCS information in thread_info as a {base,offset} pair
introduces an additional load instruction on the ret-to-user path,
since the SCS stack pointer in x18 has to be converted back to an offset
by subtracting the base.
Replace the offset with the absolute SCS stack pointer value instead
and avoid the redundant load.
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The common LED binding wants the LED node names to start with led- and
then have just a single number.
Changing the naming for the 8 user LEDs from using user<x> to led-<x>.
Also there is no default-trigger named "mmc0" in the kernel, so use the
more generic "disk-activity".
Link: https://lore.kernel.org/r/20200513103016.130417-18-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
With Book3s DAWR, ptrace and perf watchpoints on powerpc behaves
differently. Ptrace watchpoint works in one-shot mode and generates
signal before executing instruction. It's ptrace user's job to
single-step the instruction and re-enable the watchpoint. OTOH, in
case of perf watchpoint, kernel emulates/single-steps the instruction
and then generates event. If perf and ptrace creates two events with
same or overlapping address ranges, it's ambiguous to decide who
should single-step the instruction. Because of this issue, don't
allow perf and ptrace watchpoint at the same time if their address
range overlaps.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-15-ravi.bangoria@linux.ibm.com
Currently we assume that we have only one watchpoint supported by hw.
Get rid of that assumption and use dynamic loop instead. This should
make supporting more watchpoints very easy.
With more than one watchpoint, exception handler needs to know which
DAWR caused the exception, and hw currently does not provide it. So
we need sw logic for the same. To figure out which DAWR caused the
exception, check all different combinations of user specified range,
DAWR address range, actual access range and DAWRX constrains. For ex,
if user specified range and actual access range overlaps but DAWRX is
configured for readonly watchpoint and the instruction is store, this
DAWR must not have caused exception.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Michael Neuling <mikey@neuling.org>
[mpe: Unsplit multi-line printk() strings, fix some sparse warnings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200514111741.97993-14-ravi.bangoria@linux.ibm.com
So far we had only one watchpoint, so we have hardcoded HBP_NUM to 1.
But Power10 is introducing 2nd DAWR and thus kernel should be able to
dynamically find actual number of watchpoints supported by hw it's
running on. Introduce function for the same. Also convert HBP_NUM macro
to HBP_NUM_MAX, which will now represent maximum number of watchpoints
supported by Powerpc.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Link: https://lore.kernel.org/r/20200514111741.97993-4-ravi.bangoria@linux.ibm.com
This adds emulation support for the following prefixed integer
load/stores:
* Prefixed Load Byte and Zero (plbz)
* Prefixed Load Halfword and Zero (plhz)
* Prefixed Load Halfword Algebraic (plha)
* Prefixed Load Word and Zero (plwz)
* Prefixed Load Word Algebraic (plwa)
* Prefixed Load Doubleword (pld)
* Prefixed Store Byte (pstb)
* Prefixed Store Halfword (psth)
* Prefixed Store Word (pstw)
* Prefixed Store Doubleword (pstd)
* Prefixed Load Quadword (plq)
* Prefixed Store Quadword (pstq)
the follow prefixed floating-point load/stores:
* Prefixed Load Floating-Point Single (plfs)
* Prefixed Load Floating-Point Double (plfd)
* Prefixed Store Floating-Point Single (pstfs)
* Prefixed Store Floating-Point Double (pstfd)
and for the following prefixed VSX load/stores:
* Prefixed Load VSX Scalar Doubleword (plxsd)
* Prefixed Load VSX Scalar Single-Precision (plxssp)
* Prefixed Load VSX Vector [0|1] (plxv, plxv0, plxv1)
* Prefixed Store VSX Scalar Doubleword (pstxsd)
* Prefixed Store VSX Scalar Single-Precision (pstxssp)
* Prefixed Store VSX Vector [0|1] (pstxv, pstxv0, pstxv1)
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Balamuruhan S <bala24@linux.ibm.com>
[mpe: Use CONFIG_PPC64 not __powerpc64__, use get_op()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-30-jniethe5@gmail.com
If a prefixed instruction results in an alignment exception, the
SRR1_PREFIXED bit is set. The handler attempts to emulate the
responsible instruction and then increment the NIP past it. Use
SRR1_PREFIXED to determine by how much the NIP should be incremented.
Prefixed instructions are not permitted to cross 64-byte boundaries. If
they do the alignment interrupt is invoked with SRR1 BOUNDARY bit set.
If this occurs send a SIGBUS to the offending process if in user mode.
If in kernel mode call bad_page_fault().
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-29-jniethe5@gmail.com
For powerpc64, redefine the ppc_inst type so both word and prefixed
instructions can be represented. On powerpc32 the type will remain the
same. Update places which had assumed instructions to be 4 bytes long.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
[mpe: Rework the get_user_inst() macros to be parameterised, and don't
assign to the dest if an error occurred. Use CONFIG_PPC64 not
__powerpc64__ in a few places. Address other comments from
Christophe. Fix some sparse complaints.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-24-jniethe5@gmail.com
Currently patch_imm32_load_insns() is used to load an instruction to
r4 to be emulated by emulate_step(). For prefixed instructions we
would like to be able to load a 64bit immediate to r4. To prepare for
this make patch_imm64_load_insns() take an argument that decides which
register to load an immediate to - rather than hardcoding r3.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200516115449.4168796-1-mpe@ellerman.id.au
Add the BOUNDARY SRR1 bit definition for when the cause of an
alignment exception is a prefixed instruction that crosses a 64-byte
boundary. Add the PREFIXED SRR1 bit definition for exceptions caused
by prefixed instructions.
Bit 35 of SRR1 is called SRR1_ISI_N_OR_G. This name comes from it
being used to indicate that an ISI was due to the access being no-exec
or guarded. ISA v3.1 adds another purpose. It is also set if there is
an access in a cache-inhibited location for prefixed instruction.
Rename from SRR1_ISI_N_OR_G to SRR1_ISI_N_G_OR_CIP.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-23-jniethe5@gmail.com
Prefix instructions have their own FSCR bit which needs to enabled via
a CPU feature. The kernel will save the FSCR for problem state but it
needs to be enabled initially.
If prefixed instructions are made unavailable by the [H]FSCR, attempting
to use them will cause a facility unavailable exception. Add "PREFIX" to
the facility_strings[].
Currently there are no prefixed instructions that are actually emulated
by emulate_instruction() within facility_unavailable_exception().
However, when caused by a prefixed instructions the SRR1 PREFIXED bit is
set. Prepare for dealing with emulated prefixed instructions by checking
for this bit.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Link: https://lore.kernel.org/r/20200506034050.24806-22-jniethe5@gmail.com
test_translate_branch() uses two pointers to instructions within a
buffer, p and q, to test patch_branch(). The pointer arithmetic done on
them assumes a size of 4. This will not work if the instruction length
changes. Instead do the arithmetic relative to the void * to the buffer.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-21-jniethe5@gmail.com
When a new breakpoint is created, the second instruction of that
breakpoint is patched with a trap instruction. This assumes the length
of the instruction is always the same. In preparation for prefixed
instructions, remove this assumption. Insert the trap instruction at the
same time the first instruction is inserted.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Alistair Popple <alistair@popple.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-20-jniethe5@gmail.com
Currently unsigned ints are used to represent instructions on powerpc.
This has worked well as instructions have always been 4 byte words.
However, ISA v3.1 introduces some changes to instructions that mean
this scheme will no longer work as well. This change is Prefixed
Instructions. A prefixed instruction is made up of a word prefix
followed by a word suffix to make an 8 byte double word instruction.
No matter the endianness of the system the prefix always comes first.
Prefixed instructions are only planned for powerpc64.
Introduce a ppc_inst type to represent both prefixed and word
instructions on powerpc64 while keeping it possible to exclusively
have word instructions on powerpc32.
Signed-off-by: Jordan Niethe <jniethe5@gmail.com>
[mpe: Fix compile error in emulate_spe()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200506034050.24806-12-jniethe5@gmail.com
