Just take copy_from_user() out of do_insn_ioctl() into the caller and
have compat_insn() build a native version and pass it to do_insn_ioctl()
directly.
One difference from the previous commits is that the helper used to
convert 32bit variant to native has two users - compat_insn() and
compat_insnlist(). The latter will be converted in next commit;
for now we simply split the helper in two variants - "userland 32bit
to kernel native" and "userland 32bit to userland native". The latter
is renamed old get_compat_insn(); it will be gone in the next commit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Warm reboot can not reset controller qca6390 due to
lack of controllable power supply, so causes firmware
download failure during enable.
Fixed by sending VSC EDL_SOC_RESET to reset qca6390
within added device shutdown implementation.
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Tested-by: Zijun Hu <zijuhu@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Hi!
This patchset is another attempt to fix the regulator coupling on
Exynos5800/5422 SoCs. Here are links to the previous attempts:
https://lore.kernel.org/linux-samsung-soc/20191008101709.qVNy8eijBi0LynOteWFMnTg4GUwKG599n6OyYoX1Abs@z/https://lore.kernel.org/lkml/20191017102758.8104-1-m.szyprowski@samsung.com/https://lore.kernel.org/linux-pm/cover.1589528491.git.viresh.kumar@linaro.org/https://lore.kernel.org/linux-pm/20200528131130.17984-1-m.szyprowski@samsung.com/
The problem is with "vdd_int" regulator coupled with "vdd_arm" on Odroid
XU3/XU4 boards family. "vdd_arm" is handled by CPUfreq. "vdd_int" is
handled by devfreq. CPUfreq initialized quite early during boot and it
starts changing OPPs and "vdd_arm" value. Sometimes CPU activity during
boot goes down and some low-frequency OPPs are selected, what in turn
causes lowering "vdd_arm". This happens before devfreq applies its
requirements on "vdd_int". Regulator balancing code reduces "vdd_arm"
voltage value, what in turn causes lowering "vdd_int" value to the lowest
possible value. This is much below the operation point of the wcore bus,
which still runs at the highest frequency.
The issue was hard to notice because in the most cases the board managed
to boot properly, even when the regulator was set to lowest value allowed
by the regulator constraints. However, it caused some random issues,
which can be observed as "Unhandled prefetch abort" or low USB stability.
Adding more and more special cases to the generic code has been rejected,
so the only way to ensure the desired behavior on Exynos5800-based SoCs
is to make a custom regulator coupler driver.
Best regards,
Marek Szyprowski
Patch summary:
Marek Szyprowski (2):
regulator: extract voltage balancing code to separate function
soc: samsung: Add simple voltage coupler for Exynos5800
arch/arm/mach-exynos/Kconfig | 1 +
drivers/regulator/core.c | 49 ++++++++-------
drivers/soc/samsung/Kconfig | 3 +
drivers/soc/samsung/Makefile | 1 +
.../soc/samsung/exynos-regulator-coupler.c | 59 +++++++++++++++++++
include/linux/regulator/coupler.h | 8 +++
6 files changed, 101 insertions(+), 20 deletions(-)
create mode 100644 drivers/soc/samsung/exynos-regulator-coupler.c
--
2.17.1
base-commit: 8f3d9f3542
Sub-devices of a real DMA device might exist on a separate segment than
the real DMA device and its IOMMU. These devices should still have a
valid device_domain_info, but the current dma alias model won't
allocate info for the subdevice.
This patch adds a segment member to struct device_domain_info and uses
the sub-device's BDF so that these sub-devices won't alias to other
devices.
Fixes: 2b0140c696 ("iommu/vt-d: Use pci_real_dma_dev() for mapping")
Cc: stable@vger.kernel.org # v5.6+
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200527165617.297470-3-jonathan.derrick@intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Domain context mapping can encounter issues with sub-devices of a real
DMA device. A sub-device cannot have a valid context entry due to it
potentially aliasing another device's 16-bit ID. It's expected that
sub-devices of the real DMA device uses the real DMA device's requester
when context mapping.
This is an issue when a sub-device is removed where the context entry is
cleared for all aliases. Other sub-devices are still valid, resulting in
those sub-devices being stranded without valid context entries.
The correct approach is to use the real DMA device when programming the
context entries. The insertion path is correct because device_to_iommu()
will return the bus and devfn of the real DMA device. The removal path
needs to only operate on the real DMA device, otherwise the entire
context entry would be cleared for all sub-devices of the real DMA
device.
This patch also adds a helper to determine if a struct device is a
sub-device of a real DMA device.
Fixes: 2b0140c696 ("iommu/vt-d: Use pci_real_dma_dev() for mapping")
Cc: stable@vger.kernel.org # v5.6+
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200527165617.297470-2-jonathan.derrick@intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Bartosz Golaszewski <bgolaszewski@baylibre.com>:
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
I noticed that oftentimes I use regmap_update_bits() for simple bit
setting or clearing. In this case the fourth argument is superfluous as
it's always 0 or equal to the mask argument.
This series proposes to add simple bit operations for setting, clearing
and testing specific bits with regmap.
The second patch uses all three in a driver that got recently picked into
the net-next tree.
The patches obviously target different trees so - if you're ok with
the change itself - I propose you pick the first one into your regmap
tree for v5.8 and then I'll resend the second patch to add the first
user for these macros for v5.9.
v1 -> v2:
- convert the new macros to static inline functions
v2 -> v3:
- drop unneeded ternary operator
Bartosz Golaszewski (2):
regmap: provide helpers for simple bit operations
net: ethernet: mtk-star-emac: use regmap bitops
drivers/base/regmap/regmap.c | 22 +++++
drivers/net/ethernet/mediatek/mtk_star_emac.c | 80 ++++++++-----------
include/linux/regmap.h | 36 +++++++++
3 files changed, 93 insertions(+), 45 deletions(-)
base-commit: 8f3d9f3542
--
2.26.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
In many instances regmap_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200528154503.26304-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
After binding a device to an mm, device drivers currently need to
register a mm_exit handler. This function is called when the mm exits,
to gracefully stop DMA targeting the address space and flush page faults
to the IOMMU.
This is deemed too complex for the MMU release() notifier, which may be
triggered by any mmput() invocation, from about 120 callsites [1]. The
upcoming SVA module has an example of such complexity: the I/O Page
Fault handler would need to call mmput_async() instead of mmput() after
handling an IOPF, to avoid triggering the release() notifier which would
in turn drain the IOPF queue and lock up.
Another concern is the DMA stop function taking too long, up to several
minutes [2]. For some mmput() callers this may disturb other users. For
example, if the OOM killer picks the mm bound to a device as the victim
and that mm's memory is locked, if the release() takes too long, it
might choose additional innocent victims to kill.
To simplify the MMU release notifier, don't forward the notification to
device drivers. Since they don't stop DMA on mm exit anymore, the PASID
lifetime is extended:
(1) The device driver calls bind(). A PASID is allocated.
Here any DMA fault is handled by mm, and on error we don't print
anything to dmesg. Userspace can easily trigger errors by issuing DMA
on unmapped buffers.
(2) exit_mmap(), for example the process took a SIGKILL. This step
doesn't happen during normal operations. Remove the pgd from the
PASID table, since the page tables are about to be freed. Invalidate
the IOTLBs.
Here the device may still perform DMA on the address space. Incoming
transactions are aborted but faults aren't printed out. ATS
Translation Requests return Successful Translation Completions with
R=W=0. PRI Page Requests return with Invalid Request.
(3) The device driver stops DMA, possibly following release of a fd, and
calls unbind(). PASID table is cleared, IOTLB invalidated if
necessary. The page fault queues are drained, and the PASID is
freed.
If DMA for that PASID is still running here, something went seriously
wrong and errors should be reported.
For now remove iommu_sva_ops entirely. We might need to re-introduce
them at some point, for example to notify device drivers of unhandled
IOPF.
[1] https://lore.kernel.org/linux-iommu/20200306174239.GM31668@ziepe.ca/
[2] https://lore.kernel.org/linux-iommu/4d68da96-0ad5-b412-5987-2f7a6aa796c3@amd.com/
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200423125329.782066-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This currently generates a warning:
drivers/i2c/busses/i2c-sh_mobile.c: In function 'sh_mobile_i2c_isr':
drivers/i2c/busses/i2c-sh_mobile.c:399:26: warning: 'data' may be used uninitialized in this function [-Wmaybe-uninitialized]
Though the code looks okay and shouldn't ever use the variable
uninitialized. Fix the warning by moving the code around and getting rid
of 'data'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: minor updates to commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To support BT use case over UART at baud rate of 3.2 Mbps,
we need SE clocks to run at 51.2MHz frequency. Previously this
frequency was not available in clk src, so, we were requesting
for 102.4 MHz and dividing it internally by 2 to get 51.2MHz.
As now 51.2MHz frequency is made available in clk src,
adding this frequency to UART frequency table.
We will save significant amount of power, if 51.2 is used
because it belongs to LowSVS range whereas 102.4 fall into
Nominal category.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/1590747282-5487-1-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calls of the functions clk_disable_unprepare() and hci_free_dev()
were missing for the exception handling.
Thus add the missed function calls together with corresponding
jump targets.
Fixes: 055825614c ("Bluetooth: btmtkuart: add an implementation for clock osc property")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
@dev parameter of qca_suspend()/qca_resume() represents
serdev_device, but it is mistook for hci_dev and causes
succedent unexpected memory access.
Fix by taking @dev as serdev_device.
Fixes: 41d5b25fed ("Bluetooth: hci_qca: add PM support")
Signed-off-by: Zijun Hu <zijuhu@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The AGTIM flag must be cleared explicitly, otherwise the IRQ handler
will be called in an endless loop.
Fortunately, this issue currently doesn't affect mainline kernels in
practice, as the the RX FIFO trigger level is set to 1 in UFCR. When
setting the trigger level to a higher number, the issue is trivially
reproducible by any RX without DMA that doesn't fill the FIFO up to the
configured level.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200528154747.14201-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call the function to instantiate SPD EEPROMs automatically on the
main SMBus controller.
Multiplexed SMBus systems are excluded for now as they are more
complex to handle.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In simple cases we can instantiate SPD EEPROMs on the SMBus
automatically. Start with just DDR2, DDR3 and DDR4 on x86 for now,
and only for systems with no more than 4 memory slots. These
limitations may be lifted later.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
[wsa: minor change for new API]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit e8759ad17d ("serial: uapi: Add support for bus termination")
introduced the ability to enable rs485 bus termination from user space.
So far the feature is only used by a single driver, 8250_exar.c, using a
hardcoded GPIO pin specific to Siemens IOT2040 products.
Provide for a more generic solution by allowing specification of an
rs485 bus termination GPIO pin in the device tree: Amend the serial
core to retrieve the GPIO from the device tree (or ACPI table) and amend
the default ->rs485_config() callback for 8250 drivers to change the
GPIO on request from user space.
Perhaps 8250_exar.c can be converted to the generic approach in a
follow-up patch.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/94c6c800d1ca9fa04766dd1d43a8272c5ad4bedd.1589811297.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device/vendor ids from Common CIS (Card Information Structure) may be
different as device/vendor ids from CIS on particular SDIO function.
Kernel currently exports only device/vendor ids from SDIO functions and not
"main" device/vendor ids from Common CIS.
This patch exports "main" device/vendor ids for SDIO and SD combo cards at
top level mmc device in sysfs hierarchy.
Userspace can use e.g. udev rules to correctly match whole SDIO card based
on Common CIS device/vendor id and not only one particular SDIO function.
Having this information in userspace also helps developers to debug whole
SDIO card as e.g. kernel mmc quirks use device/vendor ids from Common CIS
and not from particular SDIO function. Also it allows to write userspace
applications which list all connected SDIO cards based on CIS ids.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Link: https://lore.kernel.org/r/20200527110858.17504-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1590488522-9292-2-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
WARNING: CPU: 1 PID: 85 at kernel/dma/debug.c:1302
debug_dma_map_sg+0x2a0/0x3cc mmci-pl18x 58005000.sdmmc: DMA-API: mapping sg
segment longer than device claims to support [len=126976] [max=65536]
dma api debug checks and compares the segment size to dma_get_max_seg_size
(dev->dma_parms->max_segment_size), the sdmmc variant has an internal DMA
and should define its max_segment_size constraint to avoid this warning.
This Patch defines the dev->dma_parms->max_segment_size with the constraint
already set for mmc core (host->mmc->max_seg_size).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200526155103.12514-3-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning:
WARNING: CPU: 1 PID: 20 at kernel/dma/debug.c:500 add_dma_entry+0x16c/0x17c
DMA-API: exceeded 7 overlapping mappings of cacheline 0x031d2645
Modules linked in:
CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.5.0-rc2-00021-gdeda30999c2b-dirty #49
Hardware name: STM32 (Device Tree Support)
Workqueue: events_freezable mmc_rescan
[<c03138c0>] (unwind_backtrace) from [<c030d760>] (show_stack+0x10/0x14)
[<c030d760>] (show_stack) from [<c0f2eb28>] (dump_stack+0xc0/0xd4)
[<c0f2eb28>] (dump_stack) from [<c034a14c>] (__warn+0xd0/0xf8)
[<c034a14c>] (__warn) from [<c034a530>] (warn_slowpath_fmt+0x94/0xb8)
[<c034a530>] (warn_slowpath_fmt) from [<c03bca0c>] (add_dma_entry+0x16c/0x17c)
[<c03bca0c>] (add_dma_entry) from [<c03bdf54>] (debug_dma_map_sg+0xe4/0x3d4)
[<c03bdf54>] (debug_dma_map_sg) from [<c0d09244>] (sdmmc_idma_prep_data+0x94/0xf8)
[<c0d09244>] (sdmmc_idma_prep_data) from [<c0d05a2c>] (mmci_prep_data+0x2c/0xb0)
[<c0d05a2c>] (mmci_prep_data) from [<c0d073ec>] (mmci_start_data+0x134/0x2f0)
[<c0d073ec>] (mmci_start_data) from [<c0d078d0>] (mmci_request+0xe8/0x154)
[<c0d078d0>] (mmci_request) from [<c0cecb44>] (mmc_start_request+0x94/0xbc)
DMA api debug brings to light leaking dma-mappings, dma_map_sg and
dma_unmap_sg are not correctly balanced.
If a request is prepared, the dma_map/unmap are done in asynchronous call
pre_req (prep_data) and post_req (unprep_data). In this case the
dma-mapping is right balanced.
But if the request was not prepared, the data->host_cookie is define to
zero and the dma_map/unmap must be done in the request. The dma_map is
called by mmci_dma_start (prep_data), but there is no dma_unmap in this
case.
This patch adds dma_unmap_sg when the dma is finalized and the data cookie
is zero (request not prepared).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200526155103.12514-2-ludovic.barre@st.com
Fixes: 46b723dd86 ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Accordingly to Cadence documentation, PHY write procedure is:
1. Software sets the PHY Register Address (HRS04[5:0]) and the
PHY Write Data (HRS04[15:8]) fields.
2. Software sets the PHY Write Transaction Request (HRS04[24]) field to 1.
3. Software waits as the PHY Write Transaction Acknowledge (HRS04[26])
field is equal to 0.
4. Hardware performs the write transaction to PHY register where
HRS04[15:8] is a data written to register under HRS04[5:0] address.
5. Hardware sets the PHY Transaction Acknowledge (HRS04[26]) to 1 when
transaction is completed.
6. Software clears the PHY Write Transaction Request (HRS04[24]) to 1
after noticing that the PHY Write Transaction Acknowledge (HRS04[26])
field is equal to 1.
7. Software waits for the PHY Acknowledge Register (HRS04[26]) field is
equal to 0.
Add missing steps 3 and 7. Lack of these steps causes
integrity errors detested by hardware.
Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Link: https://lore.kernel.org/r/20200525074053.7309-1-vladimir.kondratiev@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All macro names for SDIO device IDs are prefixed by vendor name to which
device ID belongs. So for consistency add Broadcom string vendor prefix to
all Cypress macro names as they belong to SDIO Broadcom vendor ID.
Change also Cypress 43012 value from decimal do hexadecimal notation to be
consistent with all other values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-11-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
