commit c2b71462d2 upstream.
The syzkaller fuzzer reported a bug in the USB hub driver which turned
out to be caused by a negative runtime-PM usage counter. This allowed
a hub to be runtime suspended at a time when the driver did not expect
it. The symptom is a WARNING issued because the hub's status URB is
submitted while it is already active:
URB 0000000031fb463e submitted while active
WARNING: CPU: 0 PID: 2917 at drivers/usb/core/urb.c:363
The negative runtime-PM usage count was caused by an unfortunate
design decision made when runtime PM was first implemented for USB.
At that time, USB class drivers were allowed to unbind from their
interfaces without balancing the usage counter (i.e., leaving it with
a positive count). The core code would take care of setting the
counter back to 0 before allowing another driver to bind to the
interface.
Later on when runtime PM was implemented for the entire kernel, the
opposite decision was made: Drivers were required to balance their
runtime-PM get and put calls. In order to maintain backward
compatibility, however, the USB subsystem adapted to the new
implementation by keeping an independent usage counter for each
interface and using it to automatically adjust the normal usage
counter back to 0 whenever a driver was unbound.
This approach involves duplicating information, but what is worse, it
doesn't work properly in cases where a USB class driver delays
decrementing the usage counter until after the driver's disconnect()
routine has returned and the counter has been adjusted back to 0.
Doing so would cause the usage counter to become negative. There's
even a warning about this in the USB power management documentation!
As it happens, this is exactly what the hub driver does. The
kick_hub_wq() routine increments the runtime-PM usage counter, and the
corresponding decrement is carried out by hub_event() in the context
of the hub_wq work-queue thread. This work routine may sometimes run
after the driver has been unbound from its interface, and when it does
it causes the usage counter to go negative.
It is not possible for hub_disconnect() to wait for a pending
hub_event() call to finish, because hub_disconnect() is called with
the device lock held and hub_event() acquires that lock. The only
feasible fix is to reverse the original design decision: remove the
duplicate interface-specific usage counter and require USB drivers to
balance their runtime PM gets and puts. As far as I know, all
existing drivers currently do this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+7634edaea4d0b341c625@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27da0d2ef9 ]
A bugfix just broke compilation of appletalk when CONFIG_SYSCTL
is disabled:
In file included from net/appletalk/ddp.c:65:
net/appletalk/ddp.c: In function 'atalk_init':
include/linux/atalk.h:164:34: error: expected expression before 'do'
#define atalk_register_sysctl() do { } while(0)
^~
net/appletalk/ddp.c:1934:7: note: in expansion of macro 'atalk_register_sysctl'
rc = atalk_register_sysctl();
This is easier to avoid by using conventional inline functions
as stubs rather than macros. The header already has inline
functions for other purposes, so I'm changing over all the
macros for consistency.
Fixes: 6377f787ae ("appletalk: Fix use-after-free in atalk_proc_exit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4046c06be ]
Use offsetof() to calculate offset of a field to take advantage of
compiler built-in version when possible, and avoid UBSAN warning when
compiling with Clang:
UBSAN: Undefined behaviour in mm/swapfile.c:3010:38
member access within null pointer of type 'union swap_header'
CPU: 6 PID: 1833 Comm: swapon Tainted: G S 4.19.23 #43
Call trace:
dump_backtrace+0x0/0x194
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0x70/0x94
ubsan_epilogue+0x14/0x44
ubsan_type_mismatch_common+0xf4/0xfc
__ubsan_handle_type_mismatch_v1+0x34/0x54
__se_sys_swapon+0x654/0x1084
__arm64_sys_swapon+0x1c/0x24
el0_svc_common+0xa8/0x150
el0_svc_compat_handler+0x2c/0x38
el0_svc_compat+0x8/0x18
Link: http://lkml.kernel.org/r/20190312081902.223764-1-pihsun@chromium.org
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6147e136ff upstream.
clang points out with hundreds of warnings that the bitrev macros have a
problem with constant input:
drivers/hwmon/sht15.c:187:11: error: variable '__x' is uninitialized when used within its own initialization
[-Werror,-Wuninitialized]
u8 crc = bitrev8(data->val_status & 0x0F);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/bitrev.h:102:21: note: expanded from macro 'bitrev8'
__constant_bitrev8(__x) : \
~~~~~~~~~~~~~~~~~~~^~~~
include/linux/bitrev.h:67:11: note: expanded from macro '__constant_bitrev8'
u8 __x = x; \
~~~ ^
Both the bitrev and the __constant_bitrev macros use an internal
variable named __x, which goes horribly wrong when passing one to the
other.
The obvious fix is to rename one of the variables, so this adds an extra
'_'.
It seems we got away with this because
- there are only a few drivers using bitrev macros
- usually there are no constant arguments to those
- when they are constant, they tend to be either 0 or (unsigned)-1
(drivers/isdn/i4l/isdnhdlc.o, drivers/iio/amplifiers/ad8366.c) and
give the correct result by pure chance.
In fact, the only driver that I could find that gets different results
with this is drivers/net/wan/slic_ds26522.c, which in turn is a driver
for fairly rare hardware (adding the maintainer to Cc for testing).
Link: http://lkml.kernel.org/r/20190322140503.123580-1-arnd@arndb.de
Fixes: 556d2f055b ("ARM: 8187/1: add CONFIG_HAVE_ARCH_BITREVERSE to support rbit instruction")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Cc: Yalin Wang <yalin.wang@sonymobile.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 355b985537 ]
net_hash_mix() currently uses kernel address of a struct net,
and is used in many places that could be used to reveal this
address to a patient attacker, thus defeating KASLR, for
the typical case (initial net namespace, &init_net is
not dynamically allocated)
I believe the original implementation tried to avoid spending
too many cycles in this function, but security comes first.
Also provide entropy regardless of CONFIG_NET_NS.
Fixes: 0b4419162a ("netns: introduce the net_hash_mix "salt" for hashes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8e2f311a68 ]
Following command:
iptables -D FORWARD -m physdev ...
causes connectivity loss in some setups.
Reason is that iptables userspace will probe kernel for the module revision
of the physdev patch, and physdev has an artificial dependency on
br_netfilter (xt_physdev use makes no sense unless a br_netfilter module
is loaded).
This causes the "phydev" module to be loaded, which in turn enables the
"call-iptables" infrastructure.
bridged packets might then get dropped by the iptables ruleset.
The better fix would be to change the "call-iptables" defaults to 0 and
enforce explicit setting to 1, but that breaks backwards compatibility.
This does the next best thing: add a request_module call to checkentry.
This was a stray '-D ... -m physdev' won't activate br_netfilter
anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31b265b3ba ]
As reported back in 2016-11 [1], the "ftdump" kdb command triggers a
BUG for "sleeping function called from invalid context".
kdb's "ftdump" command wants to call ring_buffer_read_prepare() in
atomic context. A very simple solution for this is to add allocation
flags to ring_buffer_read_prepare() so kdb can call it without
triggering the allocation error. This patch does that.
Note that in the original email thread about this, it was suggested
that perhaps the solution for kdb was to either preallocate the buffer
ahead of time or create our own iterator. I'm hoping that this
alternative of adding allocation flags to ring_buffer_read_prepare()
can be considered since it means I don't need to duplicate more of the
core trace code into "trace_kdb.c" (for either creating my own
iterator or re-preparing a ring allocator whose memory was already
allocated).
NOTE: another option for kdb is to actually figure out how to make it
reuse the existing ftrace_dump() function and totally eliminate the
duplication. This sounds very appealing and actually works (the "sr
z" command can be seen to properly dump the ftrace buffer). The
downside here is that ftrace_dump() fully consumes the trace buffer.
Unless that is changed I'd rather not use it because it means "ftdump
| grep xyz" won't be very useful to search the ftrace buffer since it
will throw away the whole trace on the first grep. A future patch to
dump only the last few lines of the buffer will also be hard to
implement.
[1] https://lkml.kernel.org/r/20161117191605.GA21459@google.com
Link: http://lkml.kernel.org/r/20190308193205.213659-1-dianders@chromium.org
Reported-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 273160ffc6 ]
sctp_hdr(skb) only works when skb->transport_header is set properly.
But in Netfilter, skb->transport_header for ipv6 is not guaranteed
to be right value for sctphdr. It would cause to fail to check the
checksum for sctp packets.
So fix it by using offset, which is always right in all places.
v1->v2:
- Fix the changelog.
Fixes: e6d8b64b34 ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a4dc6a4915 ]
When using fanouts with AF_PACKET, the demux functions such as
fanout_demux_cpu will return an index in the fanout socket array, which
corresponds to the selected socket.
The ordering of this array depends on the order the sockets were added
to a given fanout group, so for FANOUT_CPU this means sockets are bound
to cpus in the order they are configured, which is OK.
However, when stopping then restarting the interface these sockets are
bound to, the sockets are reassigned to the fanout group in the reverse
order, due to the fact that they were inserted at the head of the
interface's AF_PACKET socket list.
This means that traffic that was directed to the first socket in the
fanout group is now directed to the last one after an interface restart.
In the case of FANOUT_CPU, traffic from CPU0 will be directed to the
socket that used to receive traffic from the last CPU after an interface
restart.
This commit introduces a helper to add a socket at the tail of a list,
then uses it to register AF_PACKET sockets.
Note that this changes the order in which sockets are listed in /proc and
with sock_diag.
Fixes: dc99f60069 ("packet: Add fanout support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1602f49b58 upstream.
[This commit was a merge, but it added hlist_add_tail_rcu(), which is what we
need in this stable tree, so I've changed the subject to be more descriptive
- gregkh]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3694bd7678 ]
Currently __set_fixmap_offset is a macro function which has a local
variable called 'addr'. If a caller passes a 'phys' parameter which is
derived from a variable also called 'addr', the local variable will
shadow this, and the compiler will complain about the use of an
uninitialized variable. To avoid the issue with namespace clashes,
'addr' is prefixed with a liberal sprinkling of underscores.
Turning __set_fixmap_offset into a static inline breaks the build for
several architectures. Fixing this properly requires updates to a number
of architectures to make them agree on the prototype of __set_fixmap (it
could be done as a subsequent patch series).
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
[catalin.marinas@arm.com: squashed the original function patch and macro fixup]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0eb77e9880 ]
Currently the vmstat updater is not deferrable as a result of commit
ba4877b9ca ("vmstat: do not use deferrable delayed work for
vmstat_update"). This in turn can cause multiple interruptions of the
applications because the vmstat updater may run at
Make vmstate_update deferrable again and provide a function that folds
the differentials when the processor is going to idle mode thus
addressing the issue of the above commit in a clean way.
Note that the shepherd thread will continue scanning the differentials
from another processor and will reenable the vmstat workers if it
detects any changes.
Fixes: ba4877b9ca ("vmstat: do not use deferrable delayed work for vmstat_update")
Signed-off-by: Christoph Lameter <cl@linux.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5ea8ea2cb7 upstream.
Per listen(fd, backlog) rules, there is really no point accepting a SYN,
sending a SYNACK, and dropping the following ACK packet if accept queue
is full, because application is not draining accept queue fast enough.
This behavior is fooling TCP clients that believe they established a
flow, while there is nothing at server side. They might then send about
10 MSS (if using IW10) that will be dropped anyway while server is under
stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bdb50c531 upstream.
A dm-raid array with devices larger than 4GB won't assemble on
a 32 bit host since _check_data_dev_sectors() was added in 4.16.
This is because to_sector() treats its argument as an "unsigned long"
which is 32bits (4GB) on a 32bit host. Using "unsigned long long"
is more correct.
Kernels as early as 4.2 can have other problems due to to_sector()
being used on the size of a device.
Fixes: 0cf4503174 ("dm raid: add support for the MD RAID0 personality")
cc: stable@vger.kernel.org (v4.2+)
Reported-and-tested-by: Guillaume Perréal <gperreal@free.fr>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6321aa1975 ]
clang warns about overflowing the data[] member in the struct pnpipehdr:
net/phonet/pep.c:295:8: warning: array index 4 is past the end of the array (which contains 1 element) [-Warray-bounds]
if (hdr->data[4] == PEP_IND_READY)
^ ~
include/net/phonet/pep.h:66:3: note: array 'data' declared here
u8 data[1];
Using a flexible array member at the end of the struct avoids the
warning, but since we cannot have a flexible array member inside
of the union, each index now has to be moved back by one, which
makes it a little uglier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 625c85a62c upstream.
The cpufreq_global_kobject is created using kobject_create_and_add()
helper, which assigns the kobj_type as dynamic_kobj_ktype and show/store
routines are set to kobj_attr_show() and kobj_attr_store().
These routines pass struct kobj_attribute as an argument to the
show/store callbacks. But all the cpufreq files created using the
cpufreq_global_kobject expect the argument to be of type struct
attribute. Things work fine currently as no one accesses the "attr"
argument. We may not see issues even if the argument is used, as struct
kobj_attribute has struct attribute as its first element and so they
will both get same address.
But this is logically incorrect and we should rather use struct
kobj_attribute instead of struct global_attr in the cpufreq core and
drivers and the show/store callbacks should take struct kobj_attribute
as argument instead.
This bug is caught using CFI CLANG builds in android kernel which
catches mismatch in function prototypes for such callbacks.
Reported-by: Donghee Han <dh.han@samsung.com>
Reported-by: Sangkyu Kim <skwith.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc1780fc42 upstream.
Align the payload of "user" and "logon" keys so that users of the
keyrings service can access it as a struct that requires more than
2-byte alignment. fscrypt currently does this which results in the read
of fscrypt_key::size being misaligned as it needs 4-byte alignment.
Align to __alignof__(u64) rather than __alignof__(long) since in the
future it's conceivable that people would use structs beginning with
u64, which on some platforms would require more than 'long' alignment.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 2aa349f6e3 ("[PATCH] Keys: Export user-defined keyring operations")
Fixes: 88bd6ccdcd ("ext4 crypto: add encryption key management facilities")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c09551c6ff ]
According to the algorithm described in the comment block at the
beginning of ip_rt_send_redirect, the host should try to send
'ip_rt_redirect_number' ICMP redirect packets with an exponential
backoff and then stop sending them at all assuming that the destination
ignores redirects.
If the device has previously sent some ICMP error packets that are
rate-limited (e.g TTL expired) and continues to receive traffic,
the redirect packets will never be transmitted. This happens since
peer->rate_tokens will be typically greater than 'ip_rt_redirect_number'
and so it will never be reset even if the redirect silence timeout
(ip_rt_redirect_silence) has elapsed without receiving any packet
requiring redirects.
Fix it by using a dedicated counter for the number of ICMP redirect
packets that has been sent by the host
I have not been able to identify a given commit that introduced the
issue since ip_rt_send_redirect implements the same rate-limiting
algorithm from commit 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 04c03114be ]
soukjin bae reported a crash in tcp_v4_err() handling
ICMP_DEST_UNREACH after tcp_write_queue_head(sk)
returned a NULL pointer.
Current logic should have prevented this :
if (seq != tp->snd_una || !icsk->icsk_retransmits ||
!icsk->icsk_backoff || fastopen)
break;
Problem is the write queue might have been purged
and icsk_backoff has not been cleared.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: soukjin bae <soukjin.bae@samsung.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3b89ea9c59 ]
The features attribute is of type u64 and stored in the native endianes on
the system. The for_each_set_bit() macro takes a pointer to a 32 bit array
and goes over the bits in this area. On little Endian systems this also
works with an u64 as the most significant bit is on the highest address,
but on big endian the words are swapped. When we expect bit 15 here we get
bit 47 (15 + 32).
This patch converts it more or less to its own for_each_set_bit()
implementation which works on 64 bit integers directly. This is then
completely in host endianness and should work like expected.
Fixes: fd867d51f ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da360299b6 upstream.
This fixes a compile problem of some user space applications by not
including linux/libc-compat.h in uapi/if_ether.h.
linux/libc-compat.h checks which "features" the header files, included
from the libc, provide to make the Linux kernel uapi header files only
provide no conflicting structures and enums. If a user application mixes
kernel headers and libc headers it could happen that linux/libc-compat.h
gets included too early where not all other libc headers are included
yet. Then the linux/libc-compat.h would not prevent all the
redefinitions and we run into compile problems.
This patch removes the include of linux/libc-compat.h from
uapi/if_ether.h to fix the recently introduced case, but not all as this
is more or less impossible.
It is no problem to do the check directly in the if_ether.h file and not
in libc-compat.h as this does not need any fancy glibc header detection
as glibc never provided struct ethhdr and should define
__UAPI_DEF_ETHHDR by them self when they will provide this.
The following test program did not compile correctly any more:
#include <linux/if_ether.h>
#include <netinet/in.h>
#include <linux/in.h>
int main(void)
{
return 0;
}
Fixes: 6926e041a8 ("uapi/if_ether.h: prevent redefinition of struct ethhdr")
Reported-by: Guillaume Nault <g.nault@alphalink.fr>
Cc: <stable@vger.kernel.org> # 4.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6926e041a8 upstream.
Musl provides its own ethhdr struct definition. Add a guard to prevent
its definition of the appropriate musl header has already been included.
glibc does not implement this header, but when glibc will implement this
they can just define __UAPI_DEF_ETHHDR 0 to make it work with the
kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 13054abbaa upstream.
Ring buffer implementation in hid_debug_event() and hid_debug_events_read()
is strange allowing lost or corrupted data. After commit 717adfdaf1
("HID: debug: check length before copy_to_user()") it is possible to enter
an infinite loop in hid_debug_events_read() by providing 0 as count, this
locks up a system. Fix this by rewriting the ring buffer implementation
with kfifo and simplify the code.
This fixes CVE-2019-3819.
v2: fix an execution logic and add a comment
v3: use __set_current_state() instead of set_current_state()
Backport to v4.4: some (tree-wide) patches are missing in v4.4 so
cherry-pick relevant pieces from:
* 6396bb2215 ("treewide: kzalloc() -> kcalloc()")
* a9a08845e9 ("vfs: do bulk POLL* -> EPOLL* replacement")
* 92529623d2 ("HID: debug: improve hid_debug_event()")
* 174cd4b1e5 ("sched/headers: Prepare to move signal wakeup & sigpending
methods from <linux/sched.h> into <linux/sched/signal.h>")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1669187
Cc: stable@vger.kernel.org # v4.18+
Fixes: cd667ce247 ("HID: use debugfs for events/reports dumping")
Fixes: 717adfdaf1 ("HID: debug: check length before copy_to_user()")
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f2ab5e1d1 upstream.
It is normal user behaviour to start, stop, then start a stream
again without closing it. Currently this works for compressed
playback streams but not capture ones.
The states on a compressed capture stream go directly from OPEN to
PREPARED, unlike a playback stream which moves to SETUP and waits
for a write of data before moving to PREPARED. Currently however,
when a stop is sent the state is set to SETUP for both types of
streams. This leaves a capture stream in the situation where a new
start can't be sent as that requires the state to be PREPARED and
a new set_params can't be sent as that requires the state to be
OPEN. The only option being to close the stream, and then reopen.
Correct this issues by allowing snd_compr_drain_notify to set the
state depending on the stream direction, as we already do in
set_params.
Fixes: 49bb6402f1 ("ALSA: compress_core: Add support for capture streams")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08a77676f9 upstream.
e7fd37ba12 ("cgroup: avoid copying strings longer than the buffers")
converted possibly unsafe strncpy() usages in cgroup to strscpy().
However, although the callsites are completely fine with truncated
copied, because strscpy() is marked __must_check, it led to the
following warnings.
kernel/cgroup/cgroup.c: In function ‘cgroup_file_name’:
kernel/cgroup/cgroup.c:1400:10: warning: ignoring return value of ‘strscpy’, declared with attribute warn_unused_result [-Wunused-result]
strscpy(buf, cft->name, CGROUP_FILE_NAME_MAX);
^
To avoid the warnings, 50034ed496 ("cgroup: use strlcpy() instead of
strscpy() to avoid spurious warning") switched them to strlcpy().
strlcpy() is worse than strlcpy() because it unconditionally runs
strlen() on the source string, and the only reason we switched to
strlcpy() here was because it was lacking __must_check, which doesn't
reflect any material differences between the two function. It's just
that someone added __must_check to strscpy() and not to strlcpy().
These basic string copy operations are used in variety of ways, and
one of not-so-uncommon use cases is safely handling truncated copies,
where the caller naturally doesn't care about the return value. The
__must_check doesn't match the actual use cases and forces users to
opt for inferior variants which lack __must_check by happenstance or
spread ugly (void) casts.
Remove __must_check from strscpy() and restore strscpy() usages in
cgroup.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ma Shimiao <mashimiao.fnst@cn.fujitsu.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
[backport only the string.h portion to remove build warnings starting to show up - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a52c5a16cf ]
There are several warnings from Clang about no case statement matching
the constant 0:
In file included from drivers/block/drbd/drbd_receiver.c:48:
In file included from drivers/block/drbd/drbd_int.h:48:
In file included from ./include/linux/drbd_genl_api.h:54:
In file included from ./include/linux/genl_magic_struct.h:236:
./include/linux/drbd_genl.h:321:1: warning: no case matching constant
switch condition '0'
GENL_struct(DRBD_NLA_HELPER, 24, drbd_helper_info,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/genl_magic_struct.h:220:10: note: expanded from macro
'GENL_struct'
switch (0) {
^
Silence this warning by adding a 'case 0:' statement. Additionally,
adjust the alignment of the statements in the ct_assert_unique macro to
avoid a checkpatch warning.
This solution was originally sent by Arnd Bergmann with a default case
statement: https://lore.kernel.org/patchwork/patch/756723/
Link: https://github.com/ClangBuiltLinux/linux/issues/43
Suggested-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 353c9cb360 upstream.
This patch introduces several helper functions/macros that will be
used in the follow-up patch. No runtime changes yet.
The new logic (fully implemented in the second patch) is as follows:
* Nodes in the rb-tree will now contain not single fragments, but lists
of consecutive fragments ("runs").
* At each point in time, the current "active" run at the tail is
maintained/tracked. Fragments that arrive in-order, adjacent
to the previous tail fragment, are added to this tail run without
triggering the re-balancing of the rb-tree.
* If a fragment arrives out of order with the offset _before_ the tail run,
it is inserted into the rb-tree as a single fragment.
* If a fragment arrives after the current tail fragment (with a gap),
it starts a new "tail" run, as is inserted into the rb-tree
at the end as the head of the new run.
skb->cb is used to store additional information
needed here (suggested by Eric Dumazet).
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa0f527358 upstream.
Similar to TCP OOO RX queue, it makes sense to use rb trees to store
IP fragments, so that OOO fragments are inserted faster.
Tested:
- a follow-up patch contains a rather comprehensive ip defrag
self-test (functional)
- ran neper `udp_stream -c -H <host> -F 100 -l 300 -T 20`:
netstat --statistics
Ip:
282078937 total packets received
0 forwarded
0 incoming packets discarded
946760 incoming packets delivered
18743456 requests sent out
101 fragments dropped after timeout
282077129 reassemblies required
944952 packets reassembled ok
262734239 packet reassembles failed
(The numbers/stats above are somewhat better re:
reassemblies vs a kernel without this patchset. More
comprehensive performance testing TBD).
Reported-by: Jann Horn <jannh@google.com>
Reported-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
[bwh: Backported to 4.4:
- Keep using frag_kfree_skb() in inet_frag_destroy()
- Adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88078d98d1 upstream.
After working on IP defragmentation lately, I found that some large
packets defeat CHECKSUM_COMPLETE optimization because of NIC adding
zero paddings on the last (small) fragment.
While removing the padding with pskb_trim_rcsum(), we set skb->ip_summed
to CHECKSUM_NONE, forcing a full csum validation, even if all prior
fragments had CHECKSUM_COMPLETE set.
We can instead compute the checksum of the part we are trimming,
usually smaller than the part we keep.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7969e5c40d upstream.
This behavior is required in IPv6, and there is little need
to tolerate overlapping fragments in IPv4. This change
simplifies the code and eliminates potential DDoS attack vectors.
Tested: ran ip_defrag selftest (not yet available uptream).
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
[bwh: Backported to 4.4:
- s/__IP_INC_STATS/IP_INC_STATS_BH/
- Deleted code is slightly different]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf66337140 upstream.
ip_defrag uses skb->cb[] to store the fragment offset, and unfortunately
this integer is currently in a different cache line than skb->next,
meaning that we use two cache lines per skb when finding the insertion point.
By aliasing skb->ip_defrag_offset and skb->dev, we pack all the fields
in a single cache line and save precious memory bandwidth.
Note that after the fast path added by Changli Gao in commit
d6bebca92c ("fragment: add fast path for in-order fragments")
this change wont help the fast path, since we still need
to access prev->len (2nd cache line), but will show great
benefits when slow path is entered, since we perform
a linear scan of a potentially long list.
Also, note that this potential long list is an attack vector,
we might consider also using an rb-tree there eventually.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2615cf5a7 upstream.
Put the read-mostly fields in a separate cache line
at the beginning of struct netns_frags, to reduce
false sharing noticed in inet_frag_kill()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.4: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5d672a078 upstream.
While under frags DDOS I noticed unfortunate false sharing between
@nelems and @params.automatic_shrinking
Move @nelems at the end of struct rhashtable so that first cache line
is shared between all cpus, because almost never dirtied.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e67f106f6 upstream.
Some users are willing to provision huge amounts of memory to be able
to perform reassembly reasonnably well under pressure.
Current memory tracking is using one atomic_t and integers.
Switch to atomic_long_t so that 64bit arches can use more than 2GB,
without any cost for 32bit arches.
Note that this patch avoids an overflow error, if high_thresh was set
to ~2GB, since this test in inet_frag_alloc() was never true :
if (... || frag_mem_limit(nf) > nf->high_thresh)
Tested:
$ echo 16000000000 >/proc/sys/net/ipv4/ipfrag_high_thresh
<frag DDOS>
$ grep FRAG /proc/net/sockstat
FRAG: inuse 14705885 memory 16000002880
$ nstat -n ; sleep 1 ; nstat | grep Reas
IpReasmReqds 3317150 0.0
IpReasmFails 3317112 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 399d1404be upstream.
This refactors ip_expire() since one indentation level is removed.
Note: in the future, we should try hard to avoid the skb_clone()
since this is a serious performance cost.
Under DDOS, the ICMP message wont be sent because of rate limits.
Fact that ip6_expire_frag_queue() does not use skb_clone() is
disturbing too. Presumably IPv6 should have the same
issue than the one we fixed in commit ec4fbd6475
("inet: frag: release spinlock before calling icmp_send()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
[bwh: Backported to 4.4: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6befe4a78b upstream.
Remove sum_frag_mem_limit(), ip_frag_mem() & ip6_frag_mem()
Also since we use rhashtable we can bring back the number of fragments
in "grep FRAG /proc/net/sockstat /proc/net/sockstat6" that was
removed in commit 434d305405 ("inet: frag: don't account number
of fragment queues")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 648700f76b upstream.
Some applications still rely on IP fragmentation, and to be fair linux
reassembly unit is not working under any serious load.
It uses static hash tables of 1024 buckets, and up to 128 items per bucket (!!!)
A work queue is supposed to garbage collect items when host is under memory
pressure, and doing a hash rebuild, changing seed used in hash computations.
This work queue blocks softirqs for up to 25 ms when doing a hash rebuild,
occurring every 5 seconds if host is under fire.
Then there is the problem of sharing this hash table for all netns.
It is time to switch to rhashtables, and allocate one of them per netns
to speedup netns dismantle, since this is a critical metric these days.
Lookup is now using RCU. A followup patch will even remove
the refcount hold/release left from prior implementation and save
a couple of atomic operations.
Before this patch, 16 cpus (16 RX queue NIC) could not handle more
than 1 Mpps frags DDOS.
After the patch, I reach 9 Mpps without any tuning, and can use up to 2GB
of storage for the fragments (exact number depends on frags being evicted
after timeout)
$ grep FRAG /proc/net/sockstat
FRAG: inuse 1966916 memory 2140004608
A followup patch will change the limits for 64bit arches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Florian Westphal <fw@strlen.de>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.4: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ca8cc5bf1 upstream.
This patch modifies __rhashtable_insert_fast() so it returns the
existing object that clashes with the one that you want to insert.
In case the object is successfully inserted, NULL is returned.
Otherwise, you get an error via ERR_PTR().
This patch adapts the existing callers of __rhashtable_insert_fast()
so they handle this new logic, and it adds a new
rhashtable_lookup_get_insert_key() interface to fetch this existing
object.
nf_tables needs this change to improve handling of EEXIST cases via
honoring the NLM_F_EXCL flag and by checking if the data part of the
mapping matches what we have.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 093ba72914 upstream.
In order to simplify the API, add a pointer to struct inet_frags.
This will allow us to make things less complex.
These functions no longer have a struct inet_frags parameter :
inet_frag_destroy(struct inet_frag_queue *q /*, struct inet_frags *f */)
inet_frag_put(struct inet_frag_queue *q /*, struct inet_frags *f */)
inet_frag_kill(struct inet_frag_queue *q /*, struct inet_frags *f */)
inet_frags_exit_net(struct netns_frags *nf /*, struct inet_frags *f */)
ip6_expire_frag_queue(struct net *net, struct frag_queue *fq)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.4: inet_frag_{kill,put}() are called in some
different places; update all calls]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
