Pull md fixes from Shaohua Li:
"Some MD fixes.
The notable one is a raid5-cache deadlock bug with dm-raid, others are
not significant"
* tag 'md/4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid1/10: add missed blk plug
md: limit mdstat resync progress to max_sectors
md/r5cache: move mddev_lock() out of r5c_journal_mode_set()
md/raid5: correct degraded calculation in raid5_error
Pull DeviceTree fixes from Rob Herring:
"Another set of DT fixes:
- Fixes from overlay code rework. A trifecta of fixes to the locking,
an out of bounds access, and a memory leak in of_overlay_apply()
- Clean-up at25 eeprom binding document
- Remove leading '0x' in unit-addresses from binding docs"
* tag 'devicetree-fixes-for-4.15-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: overlay: Make node skipping in init_overlay_changeset() clearer
of: overlay: Fix out-of-bounds write in init_overlay_changeset()
of: overlay: Fix (un)locking in of_overlay_apply()
of: overlay: Fix memory leak in of_overlay_apply() error path
dt-bindings: eeprom: at25: Document device-specific compatible values
dt-bindings: eeprom: at25: Grammar s/are can/can/
dt-bindings: Remove leading 0x from bindings notation
of: overlay: Remove else after goto
of: Spelling s/changset/changeset/
of: unittest: Remove bogus overlay mutex release from overlay_data_add()
Pull virtio bugfixes from Michael Tsirkin:
"A couple of minor bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: fix return value check in receive_mergeable()
virtio_mmio: add cleanup for virtio_mmio_remove
virtio_mmio: add cleanup for virtio_mmio_probe
Pull xen fixes from Juergen Gross:
"Just two small fixes for the new pvcalls frontend driver"
* tag 'for-linus-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvcalls: Fix a check in pvcalls_front_remove()
xen/pvcalls: check for xenbus_read() errors
Remove CLK_IGNORE_UNUSED from mmc clocks. This was only needed while the
mmc driver incorrectly used the xtal as source instead of the mmc
clock. Now, the driver takes the correct clock, CCF is aware that the
clock is being used and we can remove this flag.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Marc Kleine-Budde says:
====================
pull-request: can 2017-12-08
this is a pull request of 6 patches for net/master.
Martin Kelly provides 5 patches for various USB based CAN drivers, that
properly cancel the URBs on adapter unplug, so that the driver doesn't
end up in an endless loop. Stephane Grosjean provides a patch to restart
the tx queue if zero length packages are transmitted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
Second set of fixes for 4.15. This time a lot of iwlwifi patches and
two brcmfmac patches. Most important here are the MIC and IVC fixes
for iwlwifi to unbreak 9000 series.
iwlwifi
* fix rate-scaling to not start lowest possible rate
* fix the TX queue hang detection for AP/GO modes
* fix the TX queue hang timeout in monitor interfaces
* fix packet injection
* remove a wrong error message when dumping PCI registers
* fix race condition with RF-kill
* tell mac80211 when the MIC has been stripped (9000 series)
* tell mac80211 when the IVC has been stripped (9000 series)
* add 2 new PCI IDs, one for 9000 and one for 22000
* fix a queue hang due during a P2P Remain-on-Channel operation
brcmfmac
* fix a race which sometimes caused a crash during sdio unbind
* fix a kernel-doc related build error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The first and only parameter of sl_alloc() is unused, so remove it.
Fixes: 5342b77c41 slip: ("Clean up create and destroy")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.
Fixes: 1d7d15d79f ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use meminfo to identify the egress and ingress context regions and
fetch all valid contexts from those regions. Also flush all contexts
before attempting collection to prevent stale information.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect memory layout of various on-chip memory regions. Move code
for collecting on-chip memory information to cudbg_lib.c and update
cxgb4_debugfs.c to use the common function. Also include
cudbg_entity.h before cudbg_lib.h to avoid adding cudbg entity
structure forward declarations in cudbg_lib.h.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When new veth is created, and GSO values have been configured
on one device, clone those values to the peer.
For example:
# ip link add dev vm1 gso_max_size 65530 type veth peer name vm2
This should create vm1 <--> vm2 with both having GSO maximum
size set to 65530.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing that says that number of TX queues == number of RX
queues. E.g. the ARTPEC-6 SoC has 2 TX queues and 1 RX queue.
This code is obviously wrong:
for (chan = 0; chan < tx_channel_count; chan++) {
struct stmmac_rx_queue *rx_q = &priv->rx_queue[chan];
priv->rx_queue has size MTL_MAX_RX_QUEUES, so this will send an
uninitialized napi_struct to __napi_schedule(), causing us to
crash in net_rx_action(), because napi_struct->poll is zero.
[12846.759880] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[12846.768014] pgd = (ptrval)
[12846.770742] [00000000] *pgd=39ec7831, *pte=00000000, *ppte=00000000
[12846.777023] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[12846.782942] Modules linked in:
[12846.785998] CPU: 0 PID: 161 Comm: dropbear Not tainted 4.15.0-rc2-00285-gf5fb5f2f39a7 #36
[12846.794177] Hardware name: Axis ARTPEC-6 Platform
[12846.798879] task: (ptrval) task.stack: (ptrval)
[12846.803407] PC is at 0x0
[12846.805942] LR is at net_rx_action+0x274/0x43c
[12846.810383] pc : [<00000000>] lr : [<80bff064>] psr: 200e0113
[12846.816648] sp : b90d9ae8 ip : b90d9ae8 fp : b90d9b44
[12846.821871] r10: 00000008 r9 : 0013250e r8 : 00000100
[12846.827094] r7 : 0000012c r6 : 00000000 r5 : 00000001 r4 : bac84900
[12846.833619] r3 : 00000000 r2 : b90d9b08 r1 : 00000000 r0 : bac84900
Since each DMA channel can be used for rx and tx simultaneously,
the current code should probably be rewritten so that napi_struct is
embedded in a new struct stmmac_channel.
That way, stmmac_poll() can call stmmac_tx_clean() on just the tx queue
where we got the IRQ, instead of looping through all tx queues.
This is also how the xgbe driver does it (another driver for this IP).
Fixes: c22a3f48ef ("net: stmmac: adding multiple napi mechanism")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALR table operations are a sequence of related register operations which
should be protected from concurrent access. The alr_cache should also be
protected. Add alr_mutex doing that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After applying 2270bc5da3 ("bnxt_en: Fix netpoll handling") and
903649e718 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
bnxt_poll+0x0/0xd0 exceeded budget in poll
<snip>
Call Trace:
[<ffffffff814be5cd>] dump_stack+0x4d/0x70
[<ffffffff8107e013>] __warn+0xd3/0xf0
[<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
[<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
[<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
[<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
[<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
[<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
[<ffffffff810c9549>] console_unlock+0x339/0x5b0
[<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
[<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
[<ffffffff81173df5>] printk+0x48/0x50
[<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
[<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
[<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
[<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
[<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
[<ffffffff81095f8b>] process_one_work+0x19b/0x480
[<ffffffff810967ca>] worker_thread+0x6a/0x520
[<ffffffff8109c7c4>] kthread+0xe4/0x100
[<ffffffff81884c52>] ret_from_fork+0x22/0x40
This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bytes_compl and pkts_compl pointers passed to efx_dequeue_buffers
cannot be NULL. Add a paranoid warning to check this condition and fix
the one case where they were NULL.
efx_enqueue_unwind() is called very rarely, during error handling.
Without this fix it would fail with a NULL pointer dereference in
efx_dequeue_buffer, with efx_enqueue_skb in the call stack.
Fixes: e9117e5099 ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 39e6c8208d ("net: solve a NAPI race") napi has been able
to be rescheduled within napi_complete_done() even in non-busypoll case,
but virtnet_poll() always enabled interrupts before complete, and when
napi was rescheduled within napi_complete_done() it did not disable
interrupts.
This caused more interrupts when event idx is disabled.
According to commit cbdadbbf0c ("virtio_net: fix race in RX VQ
processing") we cannot place virtqueue_enable_cb_prepare() after
NAPI_STATE_SCHED is cleared, so disable interrupts again if
napi_complete_done() returned false.
Tested with vhost-user of OVS 2.7 on host, which does not have the event
idx feature.
* Before patch:
$ netperf -t UDP_STREAM -H 192.168.150.253 -l 60 -- -m 1472
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.150.253 () port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 1472 60.00 32763206 0 6430.32
212992 60.00 23384299 4589.56
Interrupts on guest: 9872369
Packets/interrupt: 2.37
* After patch
$ netperf -t UDP_STREAM -H 192.168.150.253 -l 60 -- -m 1472
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.150.253 () port 0 AF_INET
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 1472 60.00 32794646 0 6436.49
212992 60.00 32793501 6436.27
Interrupts on guest: 4941299
Packets/interrupt: 6.64
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris requested this backmerge for a reconciliation on
drm_print.h between drm-misc-next and drm-intel-next-queued
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Pull s390 fixes from Martin Schwidefsky:
- three more patches in regard to the SPDX license tags. The missing
tags for the files in arch/s390/kvm will be merged via the KVM tree.
With that all s390 related files should have their SPDX tags.
- a patch to get rid of 'struct timespec' in the DASD driver.
- bug fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix compat system call table
s390/mm: fix off-by-one bug in 5-level page table handling
s390: Remove redudant license text
s390: add a few more SPDX identifiers
s390/dasd: prevent prefix I/O error
s390: always save and restore all registers on context switch
s390/dasd: remove 'struct timespec' usage
s390/qdio: restrict target-full handling to IQDIO
s390/qdio: consider ERROR buffers for inbound-full condition
s390/virtio: add BSD license to virtio-ccw
Pull ACPI fix from Rafael Wysocki:
"This fixes an out of bounds warning from KASAN in the ACPI CPPC
driver"
* tag 'acpi-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / CPPC: Fix KASAN global out of bounds warning
Pull power management fix from Rafael Wysocki:
"This fixes an issue in the device runtime PM framework that prevents
customer devices from resuming if runtime PM is disabled for one or
more of their supplier devices (as reflected by device links between
those devices)"
* tag 'pm-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Fix handling of suppliers with disabled runtime PM
For MTK's xHCI 1.0 or latter, TD size is the number of max
packet sized packets remaining in the TD, not including
this TRB (following spec).
For MTK's xHCI 0.96 and older, TD size is the number of max
packet sized packets remaining in the TD, including this TRB
(not following spec).
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid null pointer dereference if some function is walking through the
devs array accessing members of a new virt_dev that is mid allocation.
Add the virt_dev to xhci->devs[i] _after_ the virt_device and all its
members are properly allocated.
issue found by KASAN: null-ptr-deref in xhci_find_slot_id_by_port
"Quick analysis suggests that xhci_alloc_virt_device() is not mutex
protected. If so, there is a time frame where xhci->devs[slot_id] is set
but not fully initialized. Specifically, xhci->devs[i]->udev can be NULL."
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds basic support for BQ27521 battery monitor, used in Nokia N9
and N950. In particular, battery voltage is important to be able to
tell when the battery is almost empty. Emptying battery on N950 is
pretty painful, as flasher needs to be used to recover phone in such case.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Trace the port status of each port of a roothub when
the xhci roothub receives a Get Hub Status request.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tracing showing the port status register content each time
the xhci roothub receives a Get Port Status request.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI driver currently has the IMOD set to 160, which
translates to an IMOD interval of 40,000ns (160 * 250)ns
Commit 0cbd4b34cd ("xhci: mediatek: support MTK xHCI host controller")
introduced a QUIRK for the MTK platform to adjust this interval to 20,
which translates to an IMOD interval of 5,000ns (20 * 250)ns. This is
due to the fact that the MTK controller IMOD interval is 8 times
as much as defined in xHCI spec.
Instead of adding more quirk bits for additional platforms, this patch
introduces the ability for vendors to set the IMOD_INTERVAL as is
optimal for their platform. By using device_property_read_u32() on
"imod-interval-ns", the IMOD INTERVAL can be specified in nano seconds.
If no interval is specified, the default of 40,000ns (IMOD=160) will be
used.
No bounds checking has been implemented due to the fact that a vendor
may have violated the spec and would need to specify a value outside of
the max 8,000 IRQs/second limit specified in the xHCI spec.
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each event segment has been exposed through debugfs. There is no
need to dump ERST content with printk in code. Remove it to make
code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The content of each register has been exposed through debugfs.
There is no need to dump register content with printk in code
lines. Remove them to make code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHCI compatible USB host controllers(i.e. super-speed USB3 controllers)
can be implemented with the Debug Capability(DbC). It presents a debug
device which is fully compliant with the USB framework and provides the
equivalent of a very high performance full-duplex serial link. The debug
capability operation model and registers interface are defined in 7.6.8
of the xHCI specification, revision 1.1.
The DbC debug device shares a root port with the xHCI host. By default,
the debug capability is disabled and the root port is assigned to xHCI.
When the DbC is enabled, the root port will be assigned to the DbC debug
device, and the xHCI sees nothing on this port. This implementation uses
a sysfs node named <dbc> under the xHCI device to manage the enabling
and disabling of the debug capability.
When the debug capability is enabled, it will present a debug device
through the debug port. This debug device is fully compliant with the
USB3 framework, and it can be enumerated by a debug host on the other
end of the USB link. As soon as the debug device is configured, a TTY
serial device named /dev/ttyDBC0 will be created.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes some static functions global to avoid duplications
in different files. These functions can be used in the implementation
of xHCI debug capability. There is no functional change.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commands with input contexts are allocated with the
xhci_alloc_command_with_ctx helper.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a xhci_alloc_command_with_ctx() helper to get rid of
one of the boolean parameters telling if a context should
be allocated with the command.
No functional changes, improves core readability
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the UVC specification, stream error events carry no data.
Fix a buffer overflow (that should be harmless given data alignment)
when reporting the stream error event by removing the data byte from the
message.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
