Certain SoCs need to map the MSI address in raise_irq.
To map an address, you first need to call pci_epc_mem_alloc_addr(),
however, pci_epc_mem_alloc_addr() calls ioremap() (which can sleep).
Since raise_irq is only called from atomic context, we can't call
pci_epc_mem_alloc_addr() from raise_irq.
Pre-allocate a page in dw_pcie_ep_init(), so that this page can later
be used to map/unmap the MSI address in raise_irq.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Certain registers that pcie-designware-ep tries to write to are read-only
registers. However, these registers can become read/write if we first
enable the DBI_RO_WR_EN bit. Set/unset the DBI_RO_WR_EN bit before/after
writing these registers.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Previously, dw_pcie_ep_set_msi() wrote all bits in the Message Control
register, thus overwriting the PCI_MSI_FLAGS_64BIT bit.
By clearing the PCI_MSI_FLAGS_64BIT bit, we break MSI
on systems where the RC has set a 64 bit MSI address.
Fix dw_pcie_ep_set_msi() so that it only sets MMC bits.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Use the DMA-API to get the MSI address. This address will be written to
our PCI config space and to the register which determines which AXI
address the DWC IP will spoof for incoming MSI irqs.
Since it is a PCIe endpoint device, rather than the CPU, that is supposed
to write to the MSI address, the proper way to get the MSI address is by
using the DMA API, not by using virt_to_phys().
Using virt_to_phys() might work on some systems, but using the DMA API
should work on all systems.
This is essentially the same thing as allocating a buffer in a driver
to which the endpoint will write to. To do this, we use the DMA API.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
There are dependent clock jpgdec/audio in scpsys on MT2712,
and will exist three dependent clocks on MT2712 VDEC.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MT2712 add "set/clear" bus control register to each control register set
instead of providing only one "enable" control register, we could avoid
the read-modify-write racing by declaring "bus_prot_reg_update" as "false"
in scp_soc_data or declaring as "true" to use the legacy update method.
By improving the mtk-infracfg bus protection implementation to
support set/clear bus protection control method by IC configuration.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We added support for EXTPROC back in 2010 in commit 26df6d1340 ("tty:
Add EXTPROC support for LINEMODE") and the intent was to allow it to
override some (all?) ICANON behavior. Quoting from that original commit
message:
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
but the problem turns out that "several aspects of the terminal driver
are disabled" is a bit ambiguous, and you can really confuse the n_tty
layer by setting EXTPROC and then causing some of the ICANON invariants
to no longer be maintained.
This fixes at least one such case (TIOCINQ) becoming unhappy because of
the confusion over whether ICANON really means ICANON when EXTPROC is set.
This basically makes TIOCINQ match the case of read: if EXTPROC is set,
we ignore ICANON. Also, make sure to reset the ICANON state ie EXTPROC
changes, not just if ICANON changes.
Fixes: 26df6d1340 ("tty: Add EXTPROC support for LINEMODE")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use only 4 KiB space from the available 1 GiB PCIe aperture to access
endpoint configuration space by dynamically moving the AFI_FPCI_BAR base
address. This frees more space for mapping endpoint device BARs on some
Tegra platforms.
The ->add_bus() and ->remove_bus() callbacks are now no longer needed,
so they can be removed.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[treding@nvidia.com: various cleanups, update commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Replace the specification of data structures by variable references
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit an extra message for a memory allocation failure in these functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Patch bd36d3bab2 fixed a deadlock in the
failure path of drm_lease_create. This made the partially initialized
lease object visible for a short window of time.
To avoid having the lessee state appear transiently, I've rearranged
the code so that the lessor fields are not filled in until the
parameters are all validated and the function will succeed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171221065424.1304-1-keithp@keithp.com
Debugfs file reset_stats is created with S_IRUSR permissions,
but ocrdma_dbgfs_ops_read() doesn't support OCRDMA_RESET_STATS,
whereas ocrdma_dbgfs_ops_write() supports only OCRDMA_RESET_STATS.
The patch fixes misstype with permissions.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Prior patch mixed up what argument in the macro was what, so min value
was placed as the "default" argument, and the default value was placed
as the "min" argument. Thus, when the default was applied, it looked
like the default was smaller than the allowed min.
Swap argument postions to correct.
[mkp: fixed checkpatch warning]
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an I/O is returned with an srb_status of SRB_STATUS_INVALID_LUN
which has zero good_bytes it must be assigned an error. Otherwise the
I/O will be continuously requeued and will cause a deadlock in the case
where disks are being hot added and removed. sd_probe_async will wait
forever for its I/O to complete while holding scsi_sd_probe_domain.
Also returning the default error of DID_TARGET_FAILURE causes multipath
to not retry the I/O resulting in applications receiving I/O errors
before a failover can occur.
Signed-off-by: Cathy Avery <cavery@redhat.com>
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes following warnings reported by smatch:
drivers/scsi/qla2xxx/qla_mid.c:586 qla25xx_delete_req_que()
error: we previously assumed 'req' could be null (see line 580)
drivers/scsi/qla2xxx/qla_mid.c:602 qla25xx_delete_rsp_que()
error: we previously assumed 'rsp' could be null (see line 596)
Fixes: 7867b98dce ("scsi: qla2xxx: Fix memory leak in dual/target mode")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver may sleep under a spinlock.
The function call path is:
qedi_cpu_offline (acquire the spinlock)
qedi_fp_process_cqes
qedi_mtask_completion
qedi_process_tmf_resp
kzalloc(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool(DSAC) and checked by my
code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simplify all arcmsr_hbaX_get_config routine by call a new
get_adapter_config function.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Waiting for iop firmware ready before issue get_config command to iop
for adapter type A and D.
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If log verbose in not turned on, its hard to tell when certain error
paths get hit. Add stats counters and corresponding logic to
debugfs/sysfs to aid understanding what paths were traversed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unregistering a remote port the lpfc driver would eventually wait
for the remoteport_unreg done callback. But the driver never completed
the io aborts that would allow the connections to terminate thus the
unreg done callback was never issued. Turns out the coding style of the
driver allowed for the wait to occur on the same cpu that the deferred
isr is called on. The blocking for the wait, blocked the isr, and as the
isr didn't run, the io aborts wouldn't finish.
Turns out there was never a good reason to block waiting for the unreg
done in the first place. The driver can continue execution and the ref
counting within the driver will do the right thing.
Resolve by removing the wait and patching up a few cases where the ref
counting didn't look right - mainly cases where the remote port comes
back before the aborts had completed and the unreg done had been
called. Additionally, a few places which used pointer values to guide
driver actions weren't protected by lock, so correct those.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lpfc discovery engine, when as a nvme target, where the driver
was performing mailbox io with the adapter for port login when a NVME
PRLI is received from the host. Rather than queue and eventually get
back to sending a response after the mailbox traffic, the driver
rejected the io with an error response.
Turns out this particular initiator didn't like the rejection values
(unable to process command/command in progress) so it never attempted a
retry of the PRLI. Thus the host never established nvme connectivity
with the lpfc target.
By changing the rejection values (to Logical Busy/nothing more), the
initiator accepted the response and would retry the PRLI, resulting in
nvme connectivity.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When enabled for both SCSI and NVME support, and connected pt2pt to a
SCSI only target, the driver nodelist entry for the remote port is left
in PRLI_ISSUE state and no SCSI LUNs are discovered. Works fine if only
configured for SCSI support.
Error was due to some of the prli points still reflecting the need to
send only 1 PRLI. On a lot of fabric configs, targets were NVME only,
which meant the fabric-reported protocol attributes were only telling
the driver one protocol or the other. Thus things worked fine. With
pt2pt, the driver must send a PRLI for both protocols as there are no
hints on what the target supports. Thus pt2pt targets were hitting the
multiple PRLI issues.
Complete the dual PRLI support. Track explicitly whether scsi (fcp) or
nvme prli's have been sent. Accurately track protocol support detected
on each node as reported by the fabric or probed by PRLI traffic.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increased the sizes of the SCSI WQ's and CQ's so that SCSI operation is
similar to that used by NVME. However, size increase restricted only to
those newer adapters that can support the larger WQE size, thus bigger
queue sizes.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Handling a rcv'ed PRLI incorrectly can cause the ndlp to end up in the
wrong state or the driver to ACC and PRLI when it should send LS_RJT.
The cause was due to the driver not properly looking at the PRLI type
and taking the multiple protocol support into consideration.
Resolved by adding checks in the various PRLI receive points to validate
PRLI type and reject if not valid for the enabled protocols and mode
(host vs target).
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is all set to handle the defer_rcv api for the nvmet_fc
transport, yet didn't properly recognize the return status when the
defer_rcv occurred. The driver treated it simply as an error and aborted
the io. Several residual issues occurred at that point.
Finish the defer_rcv support: recognize the return status when the io
request is being handled in a deferred style. This stops the rogue
aborts; Replenish the async cmd rcv buffer in the deferred receive if
needed.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NVME targets appear to randomly disconnect from the initiator when
running heavy IO.
The error is due to the host aggregate (across all controllers) io load
was beyond the maximum exchange count for nvme on the adapter. The
driver was properly returning a resource busy status, but the io load
was so great heartbeat commands would be bounced and not have a
successful retry within the fuzz amount for the nvme heartbeat (yes, a
very high io load!). Thus the target was terminating the controller due
to a keep alive failure.
Resolve by reserving a few exchanges (by counters) which can be used
when the adapter is out of normal exchanges and the command is a NVME
heartbeat command. As counters are used, while the reserved command is
outstanding, as soon as any other exchange completes, the counters are
adjusted and the reserved count is replenished. The heartbeat completes
execution in a normal fashion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw SAS, it supports configuring power state from D0 to D3 for entering
Low Power status and power state from D3 to D0 for quit Low Power status.
When power state from D0 to D3, HW will send FLR to clear the registers of
ECAM and BAR space, and when power state from D3 to D0, it will clear the
registers of ECAM space only.
So when suspend, need to do like controller reset (including disable
interrupts/DQ/PHY/BUS), and also release slots after FLR. When resume,
re-config the registers of BAR space.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function sas_suspend_devices(), it requires callback lldd_port_deformed
callback to be implemented if lldd_port_deformed is implemented.
So add a stub for lldd_port_deformed.
Callback lldd_port_deformed was not required as the port deformation is done
elsewhere in the LLDD.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fix SAS_QUEUE_FULL problem. The test situation is close port while
running IO.
In sas_eh_handle_sas_errors(), SCSI EH will free sas_task of the device if
lldd_I_T_nexus_reset() return TMF_RESP_FUNC_COMPLETE or -ENODEV. But in our
SAS driver, we only free slots of the device when the return value is
TMF_RESP_FUNC_COMPLETE. So if the return value is -ENODEV, the slot resource
will not free any more.
As an solution, we should also free slots of the device in
lldd_I_T_nexus_reset() if the return value is -ENODEV.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Being called during early_initcall() is early enough that it occurs
before SMP initialization, which is all we care about for the Bus
Interface Unit configuration.
This solves lack of BIU initialization on ARM64 platforms where we do
not have an anchor where to put the BIU initialization (since there are
no machine descriptors).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We may need access to family_id and product_id fairly early on boot for
other parts of the code (e.g: biuctrl.c), so split the initialization
between an early_init() and an arch_initcall() which allows us to do
that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In order to achieve expected MCP bus throughput on 3 particular chips:
7268, 7271 and 7278, do the appropriate programming of the MCP
interface: increase number of MCP write credits, turn on write-back
throttling when present.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add definitions for B53 systems register: CPU_MCP_FLOW_REG and
CPU_WRITEBACK_CTRL_REG. These register will be saved and restored
accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In preparation for saving/restoring additional registers required on
some newer platforms (7268, 7271, 7278), migrate the code to use enums
and helper functions to access registers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
On Broadcom Brahma-B53 CPUs, the CPU_CREDIT_REG offset got moved to
0x0b0 instead of 0x184, correct this such that we correcty
enable/disable write-pairing for these chips.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In preparation for fixing and changing values in the CPU_CREDIT_REG
register for B53-based systems, make the offset parameterized.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux: (171 commits)
drm/amdgpu: fix test for shadow page tables
drm/amd/display: Expose dpp1_set_cursor_attributes
drm/amd/display: Update FMT and OPPBUF functions
drm/amd/display: check for null before calling is_blanked
drm/amd/display: dal 3.1.27
drm/amd/display: Fix unused variable warnings.
drm/amd/display: Only blank DCN when we have set_blank implementation
drm/amd/display: Put dcn_mi_registers with other structs
drm/amd/display: hubp refactor
drm/amd/display: integrating optc pseudocode
drm/amd/display: Call validate_fbc should_enable_fbc
drm/amd/display: Clean up DCN cursor code
drm/amd/display: fix 180 full screen pipe split
drm/amd/display: reprogram surface config on scaling change
drm/amd/display: Remove dwbc from pipe_ctx
drm/amd/display: Use the maximum link setting which EDP reported.
drm/amd/display: Add hdr_supported flag
drm/amd/display: fix global sync param retrieval when not pipe splitting
drm/amd/display: Update HUBP
drm/amd/display: fix rotated surface scaling
...
