[ Upstream commit a66998e0fb ]
The if statement:
if (port >= DSAF_GE_NUM)
return;
limits the value of port less than DSAF_GE_NUM (i.e., 8).
However, if the value of port is 6 or 7, an array overflow could occur:
port_rst_off = dsaf_dev->mac_cb[port]->port_rst_off;
because the length of dsaf_dev->mac_cb is DSAF_MAX_PORT_NUM (i.e., 6).
To fix this possible array overflow, we first check port and if it is
greater than or equal to DSAF_MAX_PORT_NUM, the function returns.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1527f69204 ]
AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.
commit b1a9585cc3 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix. Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0c2f8b670 ]
We can race where iscsi_session_recovery_timedout() has woken up the error
handler thread and it's now setting the devices to offline, and
session_recovery_timedout()'s call to scsi_target_unblock() is also trying
to set the device's state to transport-offline. We can then get a mix of
states.
For the case where we can't relogin we want the devices to be in
transport-offline so when we have repaired the connection
__iscsi_unblock_session() can set the state back to running.
Set the device state then call into libiscsi to wake up the error handler.
Link: https://lore.kernel.org/r/20211105221048.6541-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99b63316c3 ]
During the suspend is in process, thermal_zone_device_update bails out
thermal zone re-evaluation for any sensor trip violation without
setting next valid trip to that sensor. It assumes during resume
it will re-evaluate same thermal zone and update trip. But when it is
in suspend temperature goes down and on resume path while updating
thermal zone if temperature is less than previously violated trip,
thermal zone set trip function evaluates the same previous high and
previous low trip as new high and low trip. Since there is no change
in high/low trip, it bails out from thermal zone set trip API without
setting any trip. It leads to a case where sensor high trip or low
trip is disabled forever even though thermal zone has a valid high
or low trip.
During thermal zone device init, reset thermal zone previous high
and low trip. It resolves above mentioned scenario.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a91cf0ffbc ]
When a disk has write caching disabled, we skip submission of a bio with
flush and sync requests before writing the superblock, since it's not
needed. However when the integrity checker is enabled, this results in
reports that there are metadata blocks referred by a superblock that
were not properly flushed. So don't skip the bio submission only when
the integrity checker is enabled for the sake of simplicity, since this
is a debug tool and not meant for use in non-debug builds.
fstests/btrfs/220 trigger a check-integrity warning like the following
when CONFIG_BTRFS_FS_CHECK_INTEGRITY=y and the disk with WCE=0.
btrfs: attempt to write superblock which references block M @5242880 (sdb2/5242880/0) which is not flushed out of disk's write cache (block flush_gen=1, dev->flush_gen=0)!
------------[ cut here ]------------
WARNING: CPU: 28 PID: 843680 at fs/btrfs/check-integrity.c:2196 btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
CPU: 28 PID: 843680 Comm: umount Not tainted 5.15.0-0.rc5.39.el8.x86_64 #1
Hardware name: Dell Inc. Precision T7610/0NK70N, BIOS A18 09/11/2019
RIP: 0010:btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
RSP: 0018:ffffb642afb47940 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: 00000000ffffffff RSI: ffff8b722fc97d00 RDI: ffff8b722fc97d00
RBP: ffff8b5601c00000 R08: 0000000000000000 R09: c0000000ffff7fff
R10: 0000000000000001 R11: ffffb642afb476f8 R12: ffffffffffffffff
R13: ffffb642afb47974 R14: ffff8b5499254c00 R15: 0000000000000003
FS: 00007f00a06d4080(0000) GS:ffff8b722fc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fff5cff5ff0 CR3: 00000001c0c2a006 CR4: 00000000001706e0
Call Trace:
btrfsic_process_written_block+0x2f7/0x850 [btrfs]
__btrfsic_submit_bio.part.19+0x310/0x330 [btrfs]
? bio_associate_blkg_from_css+0xa4/0x2c0
btrfsic_submit_bio+0x18/0x30 [btrfs]
write_dev_supers+0x81/0x2a0 [btrfs]
? find_get_pages_range_tag+0x219/0x280
? pagevec_lookup_range_tag+0x24/0x30
? __filemap_fdatawait_range+0x6d/0xf0
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
? find_first_extent_bit+0x9b/0x160 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
write_all_supers+0x1b3/0xa70 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
btrfs_commit_transaction+0x59d/0xac0 [btrfs]
close_ctree+0x11d/0x339 [btrfs]
generic_shutdown_super+0x71/0x110
kill_anon_super+0x14/0x30
btrfs_kill_super+0x12/0x20 [btrfs]
deactivate_locked_super+0x31/0x70
cleanup_mnt+0xb8/0x140
task_work_run+0x6d/0xb0
exit_to_user_mode_prepare+0x1f0/0x200
syscall_exit_to_user_mode+0x12/0x30
do_syscall_64+0x46/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f009f711dfb
RSP: 002b:00007fff5cff7928 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
RAX: 0000000000000000 RBX: 000055b68c6c9970 RCX: 00007f009f711dfb
RDX: 0000000000000001 RSI: 0000000000000000 RDI: 000055b68c6c9b50
RBP: 0000000000000000 R08: 000055b68c6ca900 R09: 00007f009f795580
R10: 0000000000000000 R11: 0000000000000246 R12: 000055b68c6c9b50
R13: 00007f00a04bf184 R14: 0000000000000000 R15: 00000000ffffffff
---[ end trace 2c4b82abcef9eec4 ]---
S-65536(sdb2/65536/1)
-->
M-1064960(sdb2/1064960/1)
Reviewed-by: Filipe Manana <fdmanana@gmail.com>
Signed-off-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dbc4cb466 ]
There is a difference in how architectures treat "mem=" option. For some
that is an amount of online memory, for s390 and x86 this is the limiting
max address. Some memblock api like memblock_enforce_memory_limit()
take limit argument and explicitly treat it as the size of online memory,
and use __find_max_addr to convert it to an actual max address. Current
s390 usage:
memblock_enforce_memory_limit(memblock_end_of_DRAM());
yields different results depending on presence of memory holes (offline
memory blocks in between online memory). If there are no memory holes
limit == max_addr in memblock_enforce_memory_limit() and it does trim
online memory and reserved memory regions. With memory holes present it
actually does nothing.
Since we already use memblock_remove() explicitly to trim online memory
regions to potential limit (think mem=, kdump, addressing limits, etc.)
drop the usage of memblock_enforce_memory_limit() altogether. Trimming
reserved regions should not be required, since we now use
memblock_set_current_limit() to limit allocations and any explicit memory
reservations above the limit is an actual problem we should not hide.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39f5329218 ]
When WWAN device wake from S3 deep, under thinkpad platform,
WWAN would be disabled. This disable status could be checked
by command 'nmcli r wwan' or 'rfkill list'.
Issue analysis as below:
When host resume from S3 deep, thinkpad_acpi driver would
call hotkey_resume() function. Finnaly, it will use
wan_get_status to check the current status of WWAN device.
During this resume progress, wan_get_status would always
return off even WWAN boot up completely.
In patch V2, Hans said 'sw_state should be unchanged
after a suspend/resume. It's better to drop the
tpacpi_rfk_update_swstate call all together from the
resume path'.
And it's confimed by Lenovo that GWAN is no longer
available from WHL generation because the design does not
match with current pin control.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20211108060648.8212-1-slark_xiao@163.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6def480181 ]
When kmemdup called failed and register_net_sysctl return NULL, should
return ENOMEM instead of ENOBUFS
Signed-off-by: liuguoqiang <liuguoqiang@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b922f62259 ]
This bug report shows up when running our research tools. The
reports is SOOB read, but it seems SOOB write is also possible
a few lines below.
In details, fw.len and sw.len are inputs coming from io. A len
over the size of self->rpc triggers SOOB. The patch fixes the
bugs by adding sanity checks.
The bugs are triggerable with compromised/malfunctioning devices.
They are potentially exploitable given they first leak up to
0xffff bytes and able to overwrite the region later.
The patch is tested with QEMU emulater.
This is NOT tested with a real device.
Attached is the log we found by fuzzing.
BUG: KASAN: slab-out-of-bounds in
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
Read of size 4 at addr ffff888016260b08 by task modprobe/213
CPU: 0 PID: 213 Comm: modprobe Not tainted 5.6.0 #1
Call Trace:
dump_stack+0x76/0xa0
print_address_description.constprop.0+0x16/0x200
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
__kasan_report.cold+0x37/0x7c
? aq_hw_read_reg_bit+0x60/0x70 [atlantic]
? hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
kasan_report+0xe/0x20
hw_atl_utils_fw_upload_dwords+0x393/0x3c0 [atlantic]
hw_atl_utils_fw_rpc_call+0x95/0x130 [atlantic]
hw_atl_utils_fw_rpc_wait+0x176/0x210 [atlantic]
hw_atl_utils_mpi_create+0x229/0x2e0 [atlantic]
? hw_atl_utils_fw_rpc_wait+0x210/0x210 [atlantic]
? hw_atl_utils_initfw+0x9f/0x1c8 [atlantic]
hw_atl_utils_initfw+0x12a/0x1c8 [atlantic]
aq_nic_ndev_register+0x88/0x650 [atlantic]
? aq_nic_ndev_init+0x235/0x3c0 [atlantic]
aq_pci_probe+0x731/0x9b0 [atlantic]
? aq_pci_func_init+0xc0/0xc0 [atlantic]
local_pci_probe+0xd3/0x160
pci_device_probe+0x23f/0x3e0
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3506eee81 ]
Fix the length of holes reported at the end of a file: the length is
relative to the beginning of the extent, not the seek position which is
rounded down to the filesystem block size.
This bug went unnoticed for some time, but is now caught by the
following assertion in iomap_iter_done():
WARN_ON_ONCE(iter->iomap.offset + iter->iomap.length <= iter->pos)
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5df867145f upstream.
Depending on include order:
include/linux/of_clk.h:11:45: warning: ‘struct device_node’ declared inside parameter list will not be visible outside of this definition or declaration
unsigned int of_clk_get_parent_count(struct device_node *np);
^~~~~~~~~~~
include/linux/of_clk.h:12:43: warning: ‘struct device_node’ declared inside parameter list will not be visible outside of this definition or declaration
const char *of_clk_get_parent_name(struct device_node *np, int index);
^~~~~~~~~~~
include/linux/of_clk.h:13:31: warning: ‘struct of_device_id’ declared inside parameter list will not be visible outside of this definition or declaration
void of_clk_init(const struct of_device_id *matches);
^~~~~~~~~~~~
Fix this by adding forward declarations for struct device_node and
struct of_device_id.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lkml.kernel.org/r/20200205194649.31309-1-geert+renesas@glider.be
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f015d89a4 upstream.
The mechanism in use to allow the client to see the results of COPY/CLONE
is to drop those pages from the pagecache. This forces the client to read
those pages once more from the server. However, truncate_pagecache_range()
zeros out partial pages instead of dropping them. Let us instead use
invalidate_inode_pages2_range() with full-page offsets to ensure the client
properly sees the results of COPY/CLONE operations.
Cc: <stable@vger.kernel.org> # v4.7+
Fixes: 2e72448b07 ("NFS: Add COPY nfs operation")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85b6d24646 upstream.
Currently, the exit_shm() function not designed to work properly when
task->sysvshm.shm_clist holds shm objects from different IPC namespaces.
This is a real pain when sysctl kernel.shm_rmid_forced = 1, because it
leads to use-after-free (reproducer exists).
This is an attempt to fix the problem by extending exit_shm mechanism to
handle shm's destroy from several IPC ns'es.
To achieve that we do several things:
1. add a namespace (non-refcounted) pointer to the struct shmid_kernel
2. during new shm object creation (newseg()/shmget syscall) we
initialize this pointer by current task IPC ns
3. exit_shm() fully reworked such that it traverses over all shp's in
task->sysvshm.shm_clist and gets IPC namespace not from current task
as it was before but from shp's object itself, then call
shm_destroy(shp, ns).
Note: We need to be really careful here, because as it was said before
(1), our pointer to IPC ns non-refcnt'ed. To be on the safe side we
using special helper get_ipc_ns_not_zero() which allows to get IPC ns
refcounter only if IPC ns not in the "state of destruction".
Q/A
Q: Why can we access shp->ns memory using non-refcounted pointer?
A: Because shp object lifetime is always shorther than IPC namespace
lifetime, so, if we get shp object from the task->sysvshm.shm_clist
while holding task_lock(task) nobody can steal our namespace.
Q: Does this patch change semantics of unshare/setns/clone syscalls?
A: No. It's just fixes non-covered case when process may leave IPC
namespace without getting task->sysvshm.shm_clist list cleaned up.
Link: https://lkml.kernel.org/r/67bb03e5-f79c-1815-e2bf-949c67047418@colorfullife.com
Link: https://lkml.kernel.org/r/20211109151501.4921-1-manfred@colorfullife.com
Fixes: ab602f7991 ("shm: make exit_shm work proportional to task activity")
Co-developed-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Andrei Vagin <avagin@gmail.com>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Vasily Averin <vvs@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a884daa61a upstream.
Today netfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Note that only the tx queue needs special id handling, as for the rx
queue the id is equal to the index in the ring page.
Introduce a new indicator for the device whether it is broken and let
the device stop working when it is set. Set this indicator in case the
backend sets any weird data.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21631d2d74 upstream.
The tx_skb_freelist elements are in a single linked list with the
request id used as link reference. The per element link field is in a
union with the skb pointer of an in use request.
Move the link reference out of the union in order to enable a later
reuse of it for requests which need a populated skb pointer.
Rename add_id_to_freelist() and get_id_from_freelist() to
add_id_to_list() and get_id_from_list() in order to prepare using
those for other lists as well. Define ~0 as value to indicate the end
of a list and place that value into the link for a request not being
on the list.
When freeing a skb zero the skb pointer in the request. Use a NULL
value of the skb pointer instead of skb_entry_is_link() for deciding
whether a request has a skb linked to it.
Remove skb_entry_set_link() and open code it instead as it is really
trivial now.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 162081ec33 upstream.
In order to avoid a malicious backend being able to influence the local
processing of a request build the request locally first and then copy
it to the ring page. Any reading from the request influencing the
processing in the frontend needs to be done on the local instance.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8446066bf8 upstream.
In order to avoid problems in case the backend is modifying a response
on the ring page while the frontend has already seen it, just read the
response into a local buffer in one go and then operate on that buffer
only.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b94e4b147f upstream.
Today blkfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Introduce a new state of the ring BLKIF_STATE_ERROR which will be
switched to in case an inconsistency is being detected. Recovering from
this state is possible only via removing and adding the virtual device
again (e.g. via a suspend/resume cycle).
Make all warning messages issued due to valid error responses rate
limited in order to avoid message floods being triggered by a malicious
backend.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Link: https://lore.kernel.org/r/20210730103854.12681-4-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 629a5d87e2 upstream.
Sync include/xen/interface/io/ring.h with Xen's newest version in
order to get the RING_COPY_RESPONSE() and RING_RESPONSE_PROD_OVERFLOW()
macros.
Note that this will correct the wrong license info by adding the
missing original copyright notice.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 473441720c upstream.
Checking buf->flags should be done before the pipe_buf_release() is called
on the pipe buffer, since releasing the buffer might modify the flags.
This is exactly what page_cache_pipe_buf_release() does, and which results
in the same VM_BUG_ON_PAGE(PageLRU(page)) that the original patch was
trying to fix.
Reported-by: Justin Forbes <jmforbes@linuxtx.org>
Fixes: 712a951025 ("fuse: fix page stealing")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48b71a9e66 upstream.
There are two sites that calls queue_work() after the
destroy_workqueue() and lead to possible UAF.
The first site is nci_send_cmd(), which can happen after the
nci_close_device as below
nfcmrvl_nci_unregister_dev | nfc_genl_dev_up
nci_close_device |
flush_workqueue |
del_timer_sync |
nci_unregister_device | nfc_get_device
destroy_workqueue | nfc_dev_up
nfc_unregister_device | nci_dev_up
device_del | nci_open_device
| __nci_request
| nci_send_cmd
| queue_work !!!
Another site is nci_cmd_timer, awaked by the nci_cmd_work from the
nci_send_cmd.
... | ...
nci_unregister_device | queue_work
destroy_workqueue |
nfc_unregister_device | ...
device_del | nci_cmd_work
| mod_timer
| ...
| nci_cmd_timer
| queue_work !!!
For the above two UAF, the root cause is that the nfc_dev_up can race
between the nci_unregister_device routine. Therefore, this patch
introduce NCI_UNREG flag to easily eliminate the possible race. In
addition, the mutex_lock in nci_close_device can act as a barrier.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Fixes: 6a2968aaf5 ("NFC: basic NCI protocol implementation")
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211116152732.19238-1-linma@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4a118f2ee upstream.
When __unmap_hugepage_range() calls to huge_pmd_unshare() succeed, a TLB
flush is missing. This TLB flush must be performed before releasing the
i_mmap_rwsem, in order to prevent an unshared PMDs page from being
released and reused before the TLB flush took place.
Arguably, a comprehensive solution would use mmu_gather interface to
batch the TLB flushes and the PMDs page release, however it is not an
easy solution: (1) try_to_unmap_one() and try_to_migrate_one() also call
huge_pmd_unshare() and they cannot use the mmu_gather interface; and (2)
deferring the release of the page reference for the PMDs page until
after i_mmap_rwsem is dropeed can confuse huge_pmd_unshare() into
thinking PMDs are shared when they are not.
Fix __unmap_hugepage_range() by adding the missing TLB flush, and
forcing a flush when unshare is successful.
Fixes: 24669e5847 ("hugetlb: use mmu_gather instead of a temporary linked list for accumulating pages)" # 3.6
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe3d100240 upstream.
We should not walk/touch page tables outside of VMA boundaries when
holding only the mmap sem in read mode. Evil user space can modify the
VMA layout just before this function runs and e.g., trigger races with
page table removal code since commit dd2283f260 ("mm: mmap: zap pages
with read mmap_sem in munmap"). gfn_to_hva() will only translate using
KVM memory regions, but won't validate the VMA.
Further, we should not allocate page tables outside of VMA boundaries: if
evil user space decides to map hugetlbfs to these ranges, bad things will
happen because we suddenly have PTE or PMD page tables where we
shouldn't have them.
Similarly, we have to check if we suddenly find a hugetlbfs VMA, before
calling get_locked_pte().
Fixes: 2d42f94773 ("s390/kvm: Add PGSTE manipulation functions")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20210909162248.14969-4-david@redhat.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cb206508b upstream.
When pid filtering is activated in an instance, all of the events trace
files for that instance has the PID_FILTER flag set. This determines
whether or not pid filtering needs to be done on the event, otherwise the
event is executed as normal.
If pid filtering is enabled when an event is created (via a dynamic event
or modules), its flag is not updated to reflect the current state, and the
events are not filtered properly.
Cc: stable@vger.kernel.org
Fixes: 3fdaf80f4a ("tracing: Implement event pid filtering")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8d2ad993aa ]
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41ce097f71 ]
It hangup when booting Loongson 3A1000 with BOTH
CONFIG_PAGE_SIZE_64KB and CONFIG_MIPS_VA_BITS_48, that it turn
out to use 2-level pgtable instead of 3-level. 64KB page size
with 2-level pgtable only cover 42 bits VA, use 3-level pgtable
to cover all 48 bits VA(55 bits)
Fixes: 1e321fa917 ("MIPS64: Support of at least 48 bits of SEGBITS)
Signed-off-by: Huang Pei <huangpei@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e1fddc98d ]
While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.
It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.
Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.
Ideally these TCP_RR flows should not exit slow start.
Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.
Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.
Tested:
ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests"
Before:
8605
Ip6InReceives 87541 0.0
Ip6OutRequests 129496 0.0
TcpExtTCPHystartTrainDetect 1 0.0
TcpExtTCPHystartTrainCwnd 30 0.0
After:
8760
Ip6InReceives 88514 0.0
Ip6OutRequests 87975 0.0
Fixes: ae27e98a51 ("[TCP] CUBIC v2.3")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cefcf24b4d ]
Commit 39fbef4b0f ("PM: hibernate: Get block device exclusively in
swsusp_check()") changed the opening mode of the block device to
(FMODE_READ | FMODE_EXCL).
In the corresponding calls to swsusp_close(), the mode is still just
FMODE_READ which triggers the warning in blkdev_flush_mapping() on
resume from hibernate.
So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the
device.
Fixes: 39fbef4b0f ("PM: hibernate: Get block device exclusively in swsusp_check()")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 606a63c978 ]
The side that actively closed socket, it's clcsock doesn't enter
TIME_WAIT state, but the passive side does it. It should show the same
behavior as TCP sockets.
Consider this, when client actively closes the socket, the clcsock in
server enters TIME_WAIT state, which means the address is occupied and
won't be reused before TIME_WAIT dismissing. If we restarted server, the
service would be unavailable for a long time.
To solve this issue, shutdown the clcsock in [A], perform the TCP active
close progress first, before the passive closed side closing it. So that
the actively closed side enters TIME_WAIT, not the passive one.
Client | Server
close() // client actively close |
smc_release() |
smc_close_active() // PEERCLOSEWAIT1 |
smc_close_final() // abort or closed = 1|
smc_cdc_get_slot_and_msg_send() |
[A] |
|smc_cdc_msg_recv_action() // ACTIVE
| queue_work(smc_close_wq, &conn->close_work)
| smc_close_passive_work() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_passive_abort_received() // only in abort
|
|close() // server recv zero, close
| smc_release() // PROCESSABORT or APPCLOSEWAIT1
| smc_close_active()
| smc_close_abort() or smc_close_final() // CLOSED
| smc_cdc_get_slot_and_msg_send() // abort or closed = 1
smc_cdc_msg_recv_action() | smc_clcsock_release()
queue_work(smc_close_wq, &conn->close_work) | sock_release(tcp) // actively close clc, enter TIME_WAIT
smc_close_passive_work() // PEERCLOSEWAIT1 | smc_conn_free()
smc_close_passive_abort_received() // CLOSED|
smc_conn_free() |
smc_clcsock_release() |
sock_release(tcp) // passive close clc |
Link: https://www.spinics.net/lists/netdev/msg780407.html
Fixes: b38d732477 ("smc: socket closing and linkgroup cleanup")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ee4ba13e0 ]
While looping over shost's sdev list it is possible that one
of the drives is getting removed and its sas_target object is
freed but its sdev object remains intact.
Consequently, a kernel panic can occur while the driver is trying to access
the sas_address field of sas_target object without also checking the
sas_target object for NULL.
Link: https://lore.kernel.org/r/20211117104909.2069-1-sreekanth.reddy@broadcom.com
Fixes: f92363d123 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS")
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3c45824ad ]
The failure to retrieve post-op attributes has no bearing on whether or
not the clone operation itself was successful. We must therefore ignore
the return value of decode_getfattr() when looking at the success or
failure of nfs4_xdr_dec_clone().
Fixes: 36022770de ("nfs42: add CLONE xdr functions")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 451dc48c80 ]
This patch fixes an issue that an u32 netlink value is handled as a
signed enum value which doesn't fit into the range of u32 netlink type.
If it's handled as -1 value some BIT() evaluation ends in a
shift-out-of-bounds issue. To solve the issue we set the to u32 max which
is s32 "-1" value to keep backwards compatibility and let the followed enum
values start counting at 0. This brings the compiler to never handle the
enum as signed and a check if the value is above NL802154_IFTYPE_MAX should
filter -1 out.
Fixes: f3ea5e4423 ("ieee802154: add new interface command")
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20211112030916.685793-1-aahringo@redhat.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861afeac79 ]
Stream IDs are reused across multiple BackEnd mixers, do not reset the
stream mixers if they are not already set for that particular FrontEnd.
Ex:
amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1
would set the MultiMedia1 steam for SLIMBUS_0_RX, however doing below
command will reset previously setup MultiMedia1 stream, because both of them
are using MultiMedia1 PCM stream.
amixer cset iface=MIXER,name='SLIMBUS_2_RX Audio Mixer MultiMedia1' 0
reset the FrontEnd Mixers conditionally to fix this issue.
This is more noticeable in desktop setup, where in alsactl tries to restore
the alsa state and overwriting the previous mixer settings.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211116114721.12517-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40f7342f05 ]
The GPIO controller is also an interrupt controller provider and is
currently missing the appropriate 'interrupt-controller' and
'#interrupt-cells' properties to denote that.
Fixes: fb026d3de3 ("ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 754c4050a0 ]
The I2C interrupt controller line is off by 32 because the datasheet
describes interrupt inputs into the GIC which are for Shared Peripheral
Interrupts and are starting at offset 32. The ARM GIC binding expects
the SPI interrupts to be numbered from 0 relative to the SPI base.
Fixes: bb097e3e00 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c95c07836f ]
We are changing expire_nodest_conn to work even for reused connections when
conn_reuse_mode=0, just as what was done with commit dc7b3eb900 ("ipvs:
Fix reuse connection if real server is dead").
For controlled and persistent connections, the new connection will get the
needed real server depending on the rules in ip_vs_check_template().
Fixes: d752c36457 ("ipvs: allow rescheduling of new connections when port reuse is detected")
Co-developed-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: Chuanqi Liu <legend050709@qq.com>
Signed-off-by: yangxingwu <xingwu.yang@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7158780169 upstream.
We found out that we are unable to control the PERST# signal via the
default pin dedicated to be PERST# pin (GPIO2[3] pin) on A3700 SOC when
this pin is in EP_PCIE1_Resetn mode. There is a register in the PCIe
register space called PERSTN_GPIO_EN (D0088004[3]), but changing the
value of this register does not change the pin output when measuring
with voltmeter.
We do not know if this is a bug in the SOC, or if it works only when
PCIe controller is in a certain state.
Commit f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready
before training link") says that when this pin changes pinctrl mode
from EP_PCIE1_Resetn to GPIO, the PERST# signal is asserted for a brief
moment.
So currently the situation is that on A3700 boards the PERST# signal is
asserted in U-Boot (because the code in U-Boot issues reset via this pin
via GPIO mode), and then in Linux by the obscure and undocumented
mechanism described by the above mentioned commit.
We want to issue PERST# signal in a known way, therefore this patch
changes the pcie_reset_pin function from "pcie" to "gpio" and adds the
reset-gpios property to the PCIe node in device tree files of
EspressoBin and Armada 3720 Dev Board (Turris Mox device tree already
has this property and uDPU does not have a PCIe port).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Remi Pommarel <repk@triplefau.lt>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baf8d6899b upstream.
The PWM pins on North Bridge on Armada 37xx can be configured into PWM
or GPIO functions. When in PWM function, each pin can also be configured
to drive low on 0 and tri-state on 1 (LED mode).
The current definitions handle this by declaring two pin groups for each
pin:
- group "pwmN" with functions "pwm" and "gpio"
- group "ledN_od" ("od" for open drain) with functions "led" and "gpio"
This is semantically incorrect. The correct definition for each pin
should be one group with three functions: "pwm", "led" and "gpio".
Change the "pwmN" groups to support "led" function.
Remove "ledN_od" groups. This cannot break backwards compatibility with
older device trees: no device tree uses it since there is no PWM driver
for this SOC yet. Also "ledN_od" groups are not even documented.
Fixes: b835d69530 ("pinctrl: armada-37xx: swap polarity on LED group")
Signed-off-by: Marek Behún <kabel@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210719112938.27594-1-kabel@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
