commit 7a68d725e4 upstream.
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
> Call Trace:
> <IRQ>
> cdc_ncm_fill_tx_frame+0x83a/0x970 [cdc_ncm]
> cdc_mbim_tx_fixup+0x1d9/0x240 [cdc_mbim]
> usbnet_start_xmit+0x5d/0x720 [usbnet]
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Fixes: 4a0e3e989d ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
[jks@iki.fi: backport to 4.4.y, 4.9.y]
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59b4a8fa27 ]
The cdc_ncm driver passes network connection notifications up to
usbnet_link_change(), which is the right place for any logging.
Remove the netdev_info() duplicating this from the driver itself.
This stops devices such as my "TRENDnet USB 10/100/1G/2.5G LAN"
(ID 20f4:e02b) adapter from spamming the kernel log with
cdc_ncm 2-2:2.0 enp0s2u2c2: network connection: connected
messages every 60 msec or so.
Signed-off-by: Roland Dreier <roland@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201224032116.2453938-1-roland@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f33d9e2b48 ]
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi>
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/
Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038
Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4202c9fdf0 ]
Some WinCE devices face connectivity issues via the NDIS interface. They
fail to register, resulting in -110 timeout errors and failures during the
probe procedure.
In this kind of WinCE devices, the Windows-side ndis driver needs quite
more time to be loaded and configured, so that the linux rndis host queries
to them fail to be responded correctly on time.
More specifically, when INIT is called on the WinCE side - no other
requests can be served by the Client and this results in a failed QUERY
afterwards.
The increase of the waiting time on the side of the linux rndis host in
the command-response loop leaves the INIT process to complete and respond
to a QUERY, which comes afterwards. The WinCE devices with this special
"feature" in their ndis driver are satisfied by this fix.
Signed-off-by: Olympia Giannou <olympia.giannou@leica-geosystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a092b7233f upstream.
The buffer size is 2 Bytes and we expect to receive the same amount of
data. But sometimes we receive less data and run into uninit-was-stored
issue upon read. Hence modify the error check on the return value to match
with the buffer size as a prevention.
Reported-and-tested by: syzbot+a7e220df5a81d1ab400e@syzkaller.appspotmail.com
Signed-off-by: Himadri Pandya <himadrispandya@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 60cfe1eacc ]
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14cf4a771b ]
Telit LE920A4 uses the same pid 0x1201 of LE920, but modem
implementation is different, since it requires DTR to be set for
answering to qmi messages.
This patch replaces QMI_FIXED_INTF with QMI_QUIRK_SET_DTR: tests on
LE920 have been performed in order to verify backward compatibility.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea060b3526 ]
Drop the bogus endpoint-lookup helper which could end up accepting
interfaces based on endpoints belonging to unrelated altsettings.
Note that the returned bulk pipes and interrupt endpoint descriptor
were never actually used. Instead the bulk-endpoint numbers are
hardcoded to 1 and 2 (matching the specification), while the interrupt-
endpoint descriptor was assumed to be the third descriptor created by
USB core.
Try to bring some order to this by dropping the bogus lookup helper and
adding the missing endpoint sanity checks while keeping the interrupt-
descriptor assumption for now.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e0484010ec ]
On sparc32, tcflag_t is "unsigned long", unlike on all other
architectures, where it is "unsigned int":
drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’:
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
^~~~~~~
As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t
parameters to "unsigned int".
While at it, use "%u" to format unsigned numbers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d8e95fd6d ]
Add the missing endpoint sanity check to prevent a NULL-pointer
dereference should a malicious device lack the expected endpoints.
Note that the driver has a broken endpoint-lookup helper,
lan78xx_get_endpoints(), which can end up accepting interfaces in an
altsetting without endpoints as long as *some* altsetting has a bulk-in
and a bulk-out endpoint.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ed58f96a7 ]
In a case where the ID_REV register read is failed, the memory for a
private data structure has to be freed before returning error from the
function smsc95xx_bind.
Fixes: bbd9f9ee69 ("smsc95xx: add wol support for more frame types")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c8b1e855f ]
The return value of the function smsc95xx_reset() must be checked
to avoid returning false success from the function smsc95xx_bind().
Fixes: 2f7ca802bd ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b835a71ef6 ]
Syzbot reports an use-after-free in workqueue context:
BUG: KASAN: use-after-free in mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
mutex_unlock+0x19/0x40 kernel/locking/mutex.c:737
__smsc95xx_mdio_read drivers/net/usb/smsc95xx.c:217 [inline]
smsc95xx_mdio_read+0x583/0x870 drivers/net/usb/smsc95xx.c:278
check_carrier+0xd1/0x2e0 drivers/net/usb/smsc95xx.c:644
process_one_work+0x777/0xf90 kernel/workqueue.c:2274
worker_thread+0xa8f/0x1430 kernel/workqueue.c:2420
kthread+0x2df/0x300 kernel/kthread.c:255
It looks like that smsc95xx_unbind() is freeing the structures that are
still in use by the concurrently running workqueue callback. Thus switch
to using cancel_delayed_work_sync() to ensure the work callback really
is no longer active.
Reported-by: syzbot+29dc7d4ae19b703ff947@syzkaller.appspotmail.com
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e869e7a177 ]
Using a AX88179 device (0b95:1790), I see two bytes of appended data on
every RX packet. For example, this 48-byte ping, using 0xff as a
payload byte:
04:20:22.528472 IP 192.168.1.1 > 192.168.1.2: ICMP echo request, id 2447, seq 1, length 64
0x0000: 000a cd35 ea50 000a cd35 ea4f 0800 4500
0x0010: 0054 c116 4000 4001 f63e c0a8 0101 c0a8
0x0020: 0102 0800 b633 098f 0001 87ea cd5e 0000
0x0030: 0000 dcf2 0600 0000 0000 ffff ffff ffff
0x0040: ffff ffff ffff ffff ffff ffff ffff ffff
0x0050: ffff ffff ffff ffff ffff ffff ffff ffff
0x0060: ffff 961f
Those last two bytes - 96 1f - aren't part of the original packet.
In the ax88179 RX path, the usbnet rx_fixup function trims a 2-byte
'alignment pseudo header' from the start of the packet, and sets the
length from a per-packet field populated by hardware. It looks like that
length field *includes* the 2-byte header; the current driver assumes
that it's excluded.
This change trims the 2-byte alignment header after we've set the packet
length, so the resulting packet length is correct. While we're moving
the comment around, this also fixes the spelling of 'pseudo'.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d64c7a0803 ]
Dell USB Type C docking WD19/WD19DC attaches additional peripherals as:
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
|__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M
|__ Port 4: Dev 13, If 0, Class=Vendor Specific Class,
Driver=r8152, 5000M
where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock.
When hotplugging such dock with additional usb devices already attached on
it, the probing process may reset usb 2.1 port, therefore r8152 ethernet
device is also reset. However, during r8152 device init there are several
for-loops that, when it's unable to retrieve hardware registers due to
being disconnected from USB, may take up to 14 seconds each in practice,
and that has to be completed before USB may re-enumerate devices on the
bus. As a result, devices attached to the dock will only be available
after nearly 1 minute after the dock was plugged in:
[ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface
[ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id
[ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready
[ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr
[ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail
This happens in, for example, r8153_init:
static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size,
void *data, u16 type)
{
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return -ENODEV;
...
}
static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index)
{
u32 data;
...
generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen);
data = __le32_to_cpu(tmp);
...
return (u16)data;
}
static void r8153_init(struct r8152 *tp)
{
...
if (test_bit(RTL8152_UNPLUG, &tp->flags))
return;
for (i = 0; i < 500; i++) {
if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) &
AUTOLOAD_DONE)
break;
msleep(20);
}
...
}
Since ocp_read_word() doesn't check the return status of
generic_ocp_read(), and the only exit condition for the loop is to have
a match in the returned value, such loops will only ends after exceeding
its maximum runs when the device has been marked as disconnected, which
takes 500 * 20ms = 10 seconds in theory, 14 in practice.
To solve this long latency another test to RTL8152_UNPLUG flag should be
added after those 20ms sleep to skip unnecessary loops, so that the device
probe can complete early and proceed to parent port reset/reprobe process.
This can be reproduced on all kernel versions up to latest v5.6-rc2, but
after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less
while it was around 1/2.
Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 88bf54603f ]
Commit f25e1392fd removed the support for the pre-production variant
of the Dell DW5821e to avoid probing another USB interface unnecessarily.
However, the pre-production samples are found in the wild, and this lack
of support is causing problems for users of such samples. It is therefore
necessary to support both variants.
Matching on both interfaces 0 and 1 is not expected to cause any problem
with either variant, as only the QMI function will be probed successfully
on either. Interface 1 will be rejected based on the HID class for the
production variant:
T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev=03.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
And interface 0 will be rejected based on too few endpoints for the
pre-production variant:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2
P: Vendor=413c ProdID=81d7 Rev= 3.18
S: Manufacturer=DELL
S: Product=DW5821e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Fixes: f25e1392fd ("qmi_wwan: fix interface number for DW5821e production firmware")
Link: https://whrl.pl/Rf0vNk
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9583a3638d ]
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce896476c6 ]
As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f8d7408a4d ]
lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.
Pierre-Francois reported various hangs when/if TSO is enabled.
For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.
Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Tested-by: RENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86f3f4cd53 ]
Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.
Fixes: 40a82917b1 ("net/usb/r8152: enable interrupt transfer")
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20032b6358 ]
Lan78xx driver accesses the PHY registers through MDIO bus over USB
connection. When performing a suspend/resume, the PHY registers can be
accessed before the USB connection is resumed. This will generate an
error and will prevent the device to resume correctly.
This patch adds the dependency between the MDIO bus and USB device to
allow correct handling of suspend/resume.
Fixes: ce85e13ad6 ("lan78xx: Update to use phylib instead of mii_if_info.")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a56dcc6b45 upstream.
This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.
Fixes: 332f989a3b ("CDC-NCM: handle incomplete transfer of MTU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8353da9fa6 ]
Fix NULL-pointer dereference on tty open due to a failure to handle a
missing interrupt-in endpoint when probing modem ports:
BUG: kernel NULL pointer dereference, address: 0000000000000006
...
RIP: 0010:tiocmget_submit_urb+0x1c/0xe0 [hso]
...
Call Trace:
hso_start_serial_device+0xdc/0x140 [hso]
hso_serial_open+0x118/0x1b0 [hso]
tty_open+0xf1/0x490
Fixes: 542f548236 ("tty: Modem functions for the HSO driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8d3d7c2029 ]
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the drivers more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of these endpoints are used for memory allocations
and as divisors in many usbnet minidrivers. Avoiding zero is therefore
critical.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3fe4b33513 ]
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the driver more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of the out pipe is used as divisor. So this change
fixes a divide-by-zero bug.
Reported-by: syzbot+ce366e2b8296e25d84f5@syzkaller.appspotmail.com
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f53a7ad189 ]
get_registers() blindly copies the memory written to by the
usb_control_msg() call even if the underlying urb failed.
This could lead to junk register values being read by the driver, since
some indirect callers of get_registers() ignore the return values. One
example is:
ocp_read_dword() ignores the return value of generic_ocp_read(), which
calls get_registers().
So, emulate PCI "Master Abort" behavior by setting the buffer to all
0xFFs when usb_control_msg() fails.
This patch is copied from the r8152 driver (v2.12.0) published by
Realtek (www.realtek.com).
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d7ffcf3bf ]
A Mediatek based smartphone owner reports problems with USB
tethering in Linux. The verbose USB listing shows a rndis_host
interface pair (e0/01/03 + 10/00/00), but the driver fails to
bind with
[ 355.960428] usb 1-4: bad CDC descriptors
The problem is a failsafe test intended to filter out ACM serial
functions using the same 02/02/ff class/subclass/protocol as RNDIS.
The serial functions are recognized by their non-zero bmCapabilities.
No RNDIS function with non-zero bmCapabilities were known at the time
this failsafe was added. But it turns out that some Wireless class
RNDIS functions are using the bmCapabilities field. These functions
are uniquely identified as RNDIS by their class/subclass/protocol, so
the failing test can safely be disabled. The same applies to the two
types of Misc class RNDIS functions.
Applying the failsafe to Communication class functions only retains
the original functionality, and fixes the problem for the Mediatek based
smartphone.
Tow examples of CDC functional descriptors with non-zero bmCapabilities
from Wireless class RNDIS functions are:
0e8d:000a Mediatek Crosscall Spider X5 3G Phone
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x0f
connection notifications
sends break
line coding and serial state
get/set/clear comm features
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
and
19d2:1023 ZTE K4201-z
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC Union:
bMasterInterface 0
bSlaveInterface 1
The Mediatek example is believed to apply to most smartphones with
Mediatek firmware. The ZTE example is most likely also part of a larger
family of devices/firmwares.
Suggested-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f1472cb09f ]
In kalmia_init_and_get_ethernet_addr(), 'usb_buf' is allocated through
kmalloc(). In the following execution, if the 'status' returned by
kalmia_send_init_packet() is not 0, 'usb_buf' is not deallocated, leading
to memory leaks. To fix this issue, add the 'out' label to free 'usb_buf'.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1eca92eef1 ]
In cx82310_bind(), 'dev->partial_data' is allocated through kmalloc().
Then, the execution waits for the firmware to become ready. If the firmware
is not ready in time, the execution is terminated. However, the allocated
'dev->partial_data' is not deallocated on this path, leading to a memory
leak bug. To fix this issue, free 'dev->partial_data' before returning the
error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
