commit 5d5323a6f3 upstream.
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b77d2a0a22 ]
Some integrated OHCI controller hubs do not expose all ports of the hub
to pins on the SoC. In some cases the unconnected ports generate
spurious over-current events. For example the Broadcom 56060/Ranger 2 SoC
contains a nominally 3 port hub but only the first port is wired.
Default behaviour for ohci-platform driver is to use global over-current
protection mode (AKA "ganged"). This leads to the spurious over-current
events affecting all ports in the hub.
We now alter the default to use per-port over-current protection.
This patch results in the following configuration changes depending
on quirks:
- For quirk OHCI_QUIRK_SUPERIO no changes. These systems remain set up
for ganged power switching and no over-current protection.
- For quirk OHCI_QUIRK_AMD756 or OHCI_QUIRK_HUB_POWER power switching
remains at none, while over-current protection is now guaranteed to be
set to per-port rather than the previous behaviour where it was either
none or global over-current protection depending on the value at
function entry.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200910212512.16670-1-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7f40c233a ]
The comparison of hcd->irq to less than zero for an error check will
never be true because hcd->irq is an unsigned int. Fix this by
assigning the int retval to the return of platform_get_irq and checking
this for the -ve error condition and assigning hcd->irq to retval.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: c856b4b0fd ("USB: EHCI: ehci-mv: fix error handling in mv_ehci_probe()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200515165453.104028-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 29231826f3 upstream.
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.
Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:
struct foo;
int bar(struct foo *arg)
{
/* Do work ... */
}
EXPORT_SYMBOL_GPL(bar);
/* This contains struct foo's definition */
#include "foo.h"
int baz(struct foo *arg)
{
/* Do more work ... */
}
EXPORT_SYMBOL_GPL(baz);
Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.
The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.
In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 904df64a5f upstream.
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[ 176.496485] usb 2-4: Waited 2000ms for CONNECT
[ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[ 176.497103] usb 2-4: can't resume, status -19
[ 176.497438] usb usb2-port4: logical disconnect
Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.
So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 104592a523.
Eugeniu Rosca writes:
On Thu, Jul 09, 2020 at 09:00:23AM +0200, Eugeniu Rosca wrote:
>After integrating v4.14.186 commit 5410d158ca2a50 ("usb/ehci-platform:
>Set PM runtime as active on resume") into downstream v4.14.x, we started
>to consistently experience below panic [1] on every second s2ram of
>R-Car H3 Salvator-X Renesas reference board.
>
>After some investigations, we concluded the following:
> - the issue does not exist in vanilla v5.8-rc4+
> - [bisecting shows that] the panic on v4.14.186 is caused by the lack
> of v5.6-rc1 commit 987351e1ea ("phy: core: Add consumer device
> link support"). Getting evidence for that is easy. Reverting
> 987351e1ea in vanilla leads to a similar backtrace [2].
>
>Questions:
> - Backporting 987351e1ea ("phy: core: Add consumer device
> link support") to v4.14.187 looks challenging enough, so probably not
> worth it. Anybody to contradict this?
> - Assuming no plans to backport the missing mainline commit to v4.14.x,
> should the following three v4.14.186 commits be reverted on v4.14.x?
> * baef809ea497a4 ("usb/ohci-platform: Fix a warning when hibernating")
> * 9f33eff4958885 ("usb/xhci-plat: Set PM runtime as active on resume")
> * 5410d158ca2a50 ("usb/ehci-platform: Set PM runtime as active on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 9e148a5e5e.
Eugeniu Rosca writes:
On Thu, Jul 09, 2020 at 09:00:23AM +0200, Eugeniu Rosca wrote:
>After integrating v4.14.186 commit 5410d158ca2a50 ("usb/ehci-platform:
>Set PM runtime as active on resume") into downstream v4.14.x, we started
>to consistently experience below panic [1] on every second s2ram of
>R-Car H3 Salvator-X Renesas reference board.
>
>After some investigations, we concluded the following:
> - the issue does not exist in vanilla v5.8-rc4+
> - [bisecting shows that] the panic on v4.14.186 is caused by the lack
> of v5.6-rc1 commit 987351e1ea ("phy: core: Add consumer device
> link support"). Getting evidence for that is easy. Reverting
> 987351e1ea in vanilla leads to a similar backtrace [2].
>
>Questions:
> - Backporting 987351e1ea ("phy: core: Add consumer device
> link support") to v4.14.187 looks challenging enough, so probably not
> worth it. Anybody to contradict this?
> - Assuming no plans to backport the missing mainline commit to v4.14.x,
> should the following three v4.14.186 commits be reverted on v4.14.x?
> * baef809ea497a4 ("usb/ohci-platform: Fix a warning when hibernating")
> * 9f33eff4958885 ("usb/xhci-plat: Set PM runtime as active on resume")
> * 5410d158ca2a50 ("usb/ehci-platform: Set PM runtime as active on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 5365fc3132.
Eugeniu Rosca writes:
On Thu, Jul 09, 2020 at 09:00:23AM +0200, Eugeniu Rosca wrote:
>After integrating v4.14.186 commit 5410d158ca2a50 ("usb/ehci-platform:
>Set PM runtime as active on resume") into downstream v4.14.x, we started
>to consistently experience below panic [1] on every second s2ram of
>R-Car H3 Salvator-X Renesas reference board.
>
>After some investigations, we concluded the following:
> - the issue does not exist in vanilla v5.8-rc4+
> - [bisecting shows that] the panic on v4.14.186 is caused by the lack
> of v5.6-rc1 commit 987351e1ea ("phy: core: Add consumer device
> link support"). Getting evidence for that is easy. Reverting
> 987351e1ea in vanilla leads to a similar backtrace [2].
>
>Questions:
> - Backporting 987351e1ea ("phy: core: Add consumer device
> link support") to v4.14.187 looks challenging enough, so probably not
> worth it. Anybody to contradict this?
> - Assuming no plans to backport the missing mainline commit to v4.14.x,
> should the following three v4.14.186 commits be reverted on v4.14.x?
> * baef809ea497a4 ("usb/ohci-platform: Fix a warning when hibernating")
> * 9f33eff4958885 ("usb/xhci-plat: Set PM runtime as active on resume")
> * 5410d158ca2a50 ("usb/ehci-platform: Set PM runtime as active on resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3d71abd13 ]
USB2 devices with LPM enabled may interrupt the system suspend:
[ 932.510475] usb 1-7: usb suspend, wakeup 0
[ 932.510549] hub 1-0:1.0: hub_suspend
[ 932.510581] usb usb1: bus suspend, wakeup 0
[ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended
[ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended
..
[ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03
..
[ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
[ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
[ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16
During system suspend, USB core will let HC suspends the device if it
doesn't have remote wakeup enabled and doesn't have any children.
However, from the log above we can see that the usb 1-7 doesn't get bus
suspended due to not in U0. After a while the port finished U2 -> U0
transition, interrupts the suspend process.
The observation is that after disabling LPM, port doesn't transit to U0
immediately and can linger in U2. xHCI spec 4.23.5.2 states that the
maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for
the affected device is advertised as 400us, which is still not enough
based on my testing result.
So let's use the maximum permitted latency, 10000, to poll for U0
status to solve the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a73d9d9cfc upstream.
Unable to complete the enumeration of a USB TV Tuner device.
Per XHCI spec (4.6.5), the EP state field of the input context shall
be cleared for a set address command. In the special case of an FS
device that has "MaxPacketSize0 = 8", the Linux XHCI driver does
not do this before evaluating the context. With an XHCI controller
that checks the EP state field for parameter context error this
causes a problem in cases such as the device getting reset again
after enumeration.
When that field is cleared, the problem does not occur.
This was found and fixed by Sasi Kumar.
Cc: stable@vger.kernel.org
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ddcb71a3e upstream.
A Synopsys USB2.0 core used in Huawei Kunpeng920 SoC has a bug which
might cause the host controller not issuing ping.
Bug description:
After indicating an Interrupt on Async Advance, the software uses the
doorbell mechanism to delete the Next Link queue head of the last
executed queue head. At this time, the host controller still references
the removed queue head(the queue head is NULL). NULL reference causes
the host controller to lose the USB device.
Solution:
After deleting the Next Link queue head, when has_synopsys_hc_bug set
to 1，the software can write one of the valid queue head addresses to
the ASYNCLISTADDR register to allow the host controller to get
the valid queue head. in order to solve that problem, this patch set
the flag for Huawei Kunpeng920
There are detailed instructions and solutions in this patch:
commit 2f7ac6c199 ("USB: ehci: add workaround for Synopsys HC bug")
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1591588019-44284-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c6f8cb92c upstream.
On platforms with IOMMU enabled, multiple SGs can be coalesced into one
by the IOMMU driver. In that case the SG list processing as part of the
completion of a urb on a bulk endpoint can result into a NULL pointer
dereference with the below stack dump.
<6> Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<6> pgd = c0004000
<6> [0000000c] *pgd=00000000
<6> Internal error: Oops: 5 [#1] PREEMPT SMP ARM
<2> PC is at xhci_queue_bulk_tx+0x454/0x80c
<2> LR is at xhci_queue_bulk_tx+0x44c/0x80c
<2> pc : [<c08907c4>] lr : [<c08907bc>] psr: 000000d3
<2> sp : ca337c80 ip : 00000000 fp : ffffffff
<2> r10: 00000000 r9 : 50037000 r8 : 00004000
<2> r7 : 00000000 r6 : 00004000 r5 : 00000000 r4 : 00000000
<2> r3 : 00000000 r2 : 00000082 r1 : c2c1a200 r0 : 00000000
<2> Flags: nzcv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none
<2> Control: 10c0383d Table: b412c06a DAC: 00000051
<6> Process usb-storage (pid: 5961, stack limit = 0xca336210)
<snip>
<2> [<c08907c4>] (xhci_queue_bulk_tx)
<2> [<c0881b3c>] (xhci_urb_enqueue)
<2> [<c0831068>] (usb_hcd_submit_urb)
<2> [<c08350b4>] (usb_sg_wait)
<2> [<c089f384>] (usb_stor_bulk_transfer_sglist)
<2> [<c089f2c0>] (usb_stor_bulk_srb)
<2> [<c089fe38>] (usb_stor_Bulk_transport)
<2> [<c089f468>] (usb_stor_invoke_transport)
<2> [<c08a11b4>] (usb_stor_control_thread)
<2> [<c014a534>] (kthread)
The above NULL pointer dereference is the result of block_len and the
sent_len set to zero after the first SG of the list when IOMMU driver
is enabled. Because of this the loop of processing the SGs has run
more than num_sgs which resulted in a sg_next on the last SG of the
list which has SG_END set.
Fix this by check for the sg before any attributes of the sg are
accessed.
[modified reason for null pointer dereference in commit message subject -Mathias]
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: stable@vger.kernel.org
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200514110432.25564-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f148b9f402 upstream.
A Full-speed bulk USB audio device (DJ-Tech CTRL) with a invalid Maximum
Packet Size of 4 causes a xHC "Parameter Error" at enumeration.
This is because valid Maximum packet sizes for Full-speed bulk endpoints
are 8, 16, 32 and 64 bytes. Hosts are not required to support other values
than these. See usb 2 specs section 5.8.3 for details.
The device starts working after forcing the maximum packet size to 8.
This is most likely the case with other devices as well, so force the
maximum packet size to a valid range.
Cc: stable@vger.kernel.org
Reported-by: Rene D Obermueller <cmdrrdo@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64cc3f12d1 upstream.
When disconnecting a USB hub that has some child device(s) connected to it
(such as a USB mouse), then the stack tries to clear halt and
reset device(s) which are _already_ physically disconnected.
The issue has been reproduced with:
CPU: IMX6D5EYM10AD or MCIMX6D5EYM10AE.
SW: U-Boot 2019.07 and kernel 4.19.40.
CPU: HP Proliant Microserver Gen8.
SW: Linux version 4.2.3-300.fc23.x86_64
In this situation there will be error bit for MMF active yet the
CERR equals EHCI_TUNE_CERR + halt. Existing implementation
interprets this as a stall [1] (chapter 8.4.5).
The possible conditions when the MMF will be active + halt
can be found from [2] (Table 4-13).
Fix for the issue is to check whether MMF is active and PID Code is
IN before checking for the stall. If these conditions are true then
it is not a stall.
What happens after the fix is that when disconnecting a hub with
attached device(s) the situation is not interpret as a stall.
[1] [https://www.usb.org/document-library/usb-20-specification, usb_20.pdf]
[2] [https://www.intel.com/content/dam/www/public/us/en/documents/
technical-specifications/ehci-specification-for-usb.pdf]
Signed-off-by: Erkka Talvitie <erkka.talvitie@vincit.fi>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ef70941d5f349767f19c0ed26b0dd9eed8ad81bb.1576050523.git.erkka.talvitie@vincit.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 057d476fff upstream.
A race in xhci USB3 remote wake handling may force device back to suspend
after it initiated resume siganaling, causing a missed resume event or warm
reset of device.
When a USB3 link completes resume signaling and goes to enabled (UO)
state a interrupt is issued and the interrupt handler will clear the
bus_state->port_remote_wakeup resume flag, allowing bus suspend.
If the USB3 roothub thread just finished reading port status before
the interrupt, finding ports still in suspended (U3) state, but hasn't
yet started suspending the hub, then the xhci interrupt handler will clear
the flag that prevented roothub suspend and allow bus to suspend, forcing
all port links back to suspended (U3) state.
Example case:
usb_runtime_suspend() # because all ports still show suspended U3
usb_suspend_both()
hub_suspend(); # successful as hub->wakeup_bits not set yet
==> INTERRUPT
xhci_irq()
handle_port_status()
clear bus_state->port_remote_wakeup
usb_wakeup_notification()
sets hub->wakeup_bits;
kick_hub_wq()
<== END INTERRUPT
hcd_bus_suspend()
xhci_bus_suspend() # success as port_remote_wakeup bits cleared
Fix this by increasing roothub usage count during port resume to prevent
roothub autosuspend, and by making sure bus_state->port_remote_wakeup
flag is only cleared after resume completion is visible, i.e.
after xhci roothub returned U0 or other non-U3 link state link on a
get port status request.
Issue rootcaused by Chiasheng Lee
Cc: <stable@vger.kernel.org>
Cc: Lee, Hou-hsun <hou-hsun.lee@intel.com>
Reported-by: Lee, Chiasheng <chiasheng.lee@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bd82873f23 ]
spin_unlock_irqrestore() might be called with stale flags after
reading port status, possibly restoring interrupts to a incorrect
state.
If a usb2 port just finished resuming while the port status is read
the spin lock will be temporary released and re-acquired in a separate
function. The flags parameter is passed as value instead of a pointer,
not updating flags properly before the final spin_unlock_irqrestore()
is called.
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 8b3d45705e ("usb: Fix xHCI host issues on remote wakeup.")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c03101ff4f upstream.
The check printing out the "WARN Wrong bounce buffer write length:"
uses incorrect values when comparing bytes written from scatterlist
to bounce buffer. Actual copied lengths are fine.
The used seg->bounce_len will be set to equal new_buf_len a few lines later
in the code, but is incorrect when doing the comparison.
The patch which added this false warning was backported to 4.8+ kernels
so this should be backported as far as well.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 597c56e372 ("xhci: update bounce buffer with correct sg num")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a349b95d7c upstream.
This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.
[ 34.851754] usb 2-1: USB disconnect, device number 2
[ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[ 35.187886] Workqueue: usb_hub_wq hub_event
[ 35.192063] Call trace:
[ 35.194509] dump_backtrace+0x0/0x150
[ 35.198165] show_stack+0x14/0x20
[ 35.201475] dump_stack+0xa0/0xc4
[ 35.204785] __report_bad_irq+0x34/0xe8
[ 35.208614] note_interrupt+0x2cc/0x318
[ 35.212446] handle_irq_event_percpu+0x5c/0x88
[ 35.216883] handle_irq_event+0x48/0x78
[ 35.220712] handle_fasteoi_irq+0xb4/0x188
[ 35.224802] generic_handle_irq+0x24/0x38
[ 35.228804] __handle_domain_irq+0x5c/0xb0
[ 35.232893] gic_handle_irq+0x58/0xa8
[ 35.236548] el1_irq+0xb8/0x180
[ 35.239681] __do_softirq+0x94/0x23c
[ 35.243253] irq_exit+0xd0/0xd8
[ 35.246387] __handle_domain_irq+0x60/0xb0
[ 35.250475] gic_handle_irq+0x58/0xa8
[ 35.254130] el1_irq+0xb8/0x180
[ 35.257268] kernfs_find_ns+0x5c/0x120
[ 35.261010] kernfs_find_and_get_ns+0x3c/0x60
[ 35.265361] sysfs_unmerge_group+0x20/0x68
[ 35.269454] dpm_sysfs_remove+0x2c/0x68
[ 35.273284] device_del+0x80/0x370
[ 35.276683] hid_destroy_device+0x28/0x60
[ 35.280686] usbhid_disconnect+0x4c/0x80
[ 35.284602] usb_unbind_interface+0x6c/0x268
[ 35.288867] device_release_driver_internal+0xe4/0x1b0
[ 35.293998] device_release_driver+0x14/0x20
[ 35.298261] bus_remove_device+0x110/0x128
[ 35.302350] device_del+0x148/0x370
[ 35.305832] usb_disable_device+0x8c/0x1d0
[ 35.309921] usb_disconnect+0xc8/0x2d0
[ 35.313663] hub_event+0x6e0/0x1128
[ 35.317146] process_one_work+0x1e0/0x320
[ 35.321148] worker_thread+0x40/0x450
[ 35.324805] kthread+0x124/0x128
[ 35.328027] ret_from_fork+0x10/0x18
[ 35.331594] handlers:
[ 35.333862] [<0000000079300c1d>] usb_hcd_irq
[ 35.338126] [<0000000079300c1d>] usb_hcd_irq
[ 35.342389] Disabling IRQ #156
ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
ohci_irq()
-> process_done_list()
-> takeback_td()
-> start_ed_unlink()
So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:
/* interrupt for some other device? */
if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
return IRQ_NOTMINE;
To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().
This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3dccdaade upstream.
The AMD PLL USB quirk is incorrectly enabled on newer Ryzen
chipsets. The logic in usb_amd_find_chipset_info currently checks
for unaffected chipsets rather than affected ones. This broke
once a new chipset was added in e788787ef. It makes more sense
to reverse the logic so it won't need to be updated as new
chipsets are added. Note that the core of the workaround in
usb_amd_quirk_pll does correctly check the chipset.
Signed-off-by: Ryan Kennedy <ryan5544@gmail.com>
Fixes: e788787ef4 ("usb:xhci:Add quirk for Certain failing HP keyboard on reset after resume")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20190704153529.9429-2-ryan5544@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
