Use fcoe_ddp_xid from netdev as this is correctly set for different
device IDs to avoid DDP skip error on X550 as "xid=0x20b out-of-range"
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently credit_refill and credit_max could be zero for a TC and that
is causing Tx hang for CEE mode configuration, so to fix that have at
min credit assigned to a TC and that is as what IEEE mode already does.
Change-ID: If652c133093a21e530f4e9eab09097976f57fb12
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have done unclaimed register access check in normal
(mmio_debug=0) mode once per write. This adds probability
of finding the exact sequence where we did the bad access, but
also adds burden to each write.
As we have mmio_debug available for more fine grained analysis,
give up accuracy of detecting correct spot at the first occurrence
by doing the one shot detection and arming of mmio_debug in hangcheck
and in modeset. This removes the write path performance burden.
v2: Remove gratuitous DRM_DEBUG and return value, comments (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450250808-14864-1-git-send-email-mika.kuoppala@intel.com
If something, the usual suspect being bios, access hw
behind our back, don't let it slide into situation where
normal register access will detect this and spit out
a warn on into dmesg. On some bdw bioses this happens
during igt/bat run always and as there is not much we can
do about it, its better just to detect and flush this
explicitly on resume and only print a debug message.
v2: use DRM_DEBUG_DRIVER (Chris)
v3: s/access/mmio, s/prior/prior to, s/dev/dev_priv
Testcase: igt/pm_rpm/basic-rte
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[Mika: fixed merge conflict]
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450189512-30360-3-git-send-email-mika.kuoppala@intel.com
Currently interrupt code is the only place checking
for the unclaimed register access prior to actual register
macros using the same functionality. Rename the function
and make it return bool so that the possible error message
context is clear in the caller side. The motivation is to allow
usage of unclaimed detection on arbitrary places.
v2: rebase, s/access/mmio, s/dev/dev_priv
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450189512-30360-2-git-send-email-mika.kuoppala@intel.com
Access the unclaimed reg detection register through
one helper which also does cleanup. Note that we now access
the register only if the platform has the actual non claimed
access bit. This prevents reading the register with gens that
doesn't have the register or the unclaimed bit,
when debug_mmio > 0.
Note that we post after clearing the bit. This makes sure
that the next unclaimed write access would get detected
also if it happened right after clearing, and not fold
into the previous detection.
v2: s/unclaimed_reg_access/check_for_unclaimed_mmio (Chris)
debug log on unclaimed detection on uncore init (Joonas)
v3: remove posting read (Ville)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450200287-24080-1-git-send-email-mika.kuoppala@intel.com
If head seems stuck and engine in question is rcs,
inspect subunit state transitions from undone to done,
before deciding that this really is a hang instead of limited
progress. Only account the transitions of subunits from
undone to done once, to prevent unstable subunit states
to keep us falsely active.
As this adds one extra steps to hangcheck heuristics,
before hang is declared, it adds 1500ms to to detect hang
for render ring to a total of 7500ms. We could sample
the subunit states on first head stuck condition but
decide not to do so only in order to mimic old behaviour. This
way the check order of promotion from seqno > atchd > instdone
is consistently done.
v2: Deal with unstable done states (Arun)
Clear instdone progress on head and seqno movement (Chris)
Report raw and accumulated instdone's in in debugfs (Chris)
Return HANGCHECK_ACTIVE on undone->done
References: https://bugs.freedesktop.org/show_bug.cgi?id=93029
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448985372-19535-1-git-send-email-mika.kuoppala@intel.com
To make multi_v7_defconfig really "multi", let's add virtio drivers
to allow booting a default kernel as a KVM/QEMU guest.
MACH_VIRT is already defined, so we just add VIRTIO_BLK, VIRTIO_NET
and VIRTIO_CONSOLE to actually make this kernel useful in a guest.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The device tree version of Versatile AP/PB never had LED support
so we are missing LEDs from our hardware boards. Add this as
syscon LEDs like we did for Integrator and Juno. We need to
spawn devices in the syscon with "simple-mfd" for this to work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Versatile now only has device tree boot support, and the
device tree version does not support CONFIG_LEDS_VERSATILE.
Instead select CONFIG_LEDS_SYSCON and MFD_SYSCON, so we can
get LEDs support from the same generic driver that drives
most other ARM reference boards.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a defconfig covering all known pxa board, ie. all selectable machine
files in arch/arm/mach-pxa/*.c.
This defconfig was built by doing :
- aggregation of all known defconfigs by cat
am200epdkit_defconfig
cm_x2xx_defconfig
cm_x300_defconfig
colibri_pxa270_defconfig
colibri_pxa300_defconfig
corgi_defconfig
em_x270_defconfig
eseries_pxa_defconfig
ezx_defconfig
h5000_defconfig
imote2_defconfig
lpd270_defconfig
lubbock_defconfig
magician_defconfig
mainstone_defconfig
multi_v7_defconfig
palmz72_defconfig
pcm027_defconfig
pxa255-idp_defconfig
pxa3xx_defconfig
raumfeld_defconfig
spitz_defconfig
trizeps4_defconfig
viper_defconfig
xcep_defconfig
zeus_defconfig
- manual make menuconfig to ensure :
- all pxa implementation were selected
- all drivers were transformed into modules rather than builtin
=> as a consequence this single kernel will rely on an initramfs
=> as kernel size matters on pxa, each machine can take the subset
of modules required for it to work
- all missed configurations are selected verified by :
=> grep -i pxa .config | grep "is not set"
=> this should only show the left on purpose options (either not
selectable or sharpsl exception below)
- CONFIG_PXA_SHARPSL was disabled
This breaks the boot very early on any non Sharp platform, see
head-sharpsl.S
This defconfig was tested as booting up to the login phase on :
- lubbock (pxa25x)
- mainstone (pxa27x)
- zylonite (pxa3xx)
The completion of this work will require to :
- parse manually all the arch/arm/mach-pxa/*c files, look for all
platform devices added, and verify they are all in pxa_defconfig
- do the same to ensure all pxa specific drivers (leds, gpio, ...) are
included
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Amlogic DT changes for 4.5" from Carlo Caione:
This pull request includes the Amlogic Meson8b DTS changes for v4.5
* tag 'meson-for-4.5/dts' of https://github.com/carlocaione/linux-meson:
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
This needs same quirk as applied to other YOGA sensor hubs. Refer to commit
21589ebda6 ("HID: sensor-hub: Add in quirk for Lenovo Yogas with ITE")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There seems to be a new version of the Microchip Pick16F1454 with a
different PID (0xf2f7). This device should also be ignored by the HID
driver. The PID was observed with the second version of the Yepkit Ykush
USB hub.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Somehow an ID that has never been productized is in the
code. There are no plans to use it, so just get
rid of it.
Change-ID: I59117d48ea9ee0360b0fe33833ac8092f8a24b4c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver calls skb_set_hash even with a zero hash, that
indicates to the stack that the hash calculation is offloaded
in hardware. So the Stack doesn't do a SW hash which is required
for load balancing if the user decides to turn of rx-hashing
on our device.
This patch fixes the path so that we do not call skb_set_hash
if the feature is disabled.
Change-ID: Ic4debfa4ff91b5a72e447348a75768ed7a2d3e1b
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Unlike other tablets which are compatible with the wacom_intuos_irq handler,
INTUOSHT2 devices provide pen ID with report ID 8 instead of 5. To ensure
wacom_intuos_schedule_prox_event works as intended for these tablets, we
must be sure it uses the correct report ID in this case.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is the i40e equivalent of commit c762dff24c ("ixgbe: Look up MAC
address in Open Firmware or IDPROM").
As with that fix, attempt to look up the MAC address in Open Firmware
on systems that support it, and use IDPROM on SPARC if no OF address
is found.
In the case of the i40e there is an assumption that the default mac
address has already been set up as the primary mac filter on probe,
so if this filter is obtained from the Open Firmware or IDPROM, an
explicit write is needed via i40e_aq_mac_address_write() and
i40e_aq_add_macvlan() invocation.
The I40E_FLAG_PF_MAC flag in the platform-private i40e_pf structure
tracks whether a platform-specific mac address was found, in which
case calls to i40e_aq_mac_address_write() and i40e_aq_add_macvlan()
will be triggered.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow the user to specify a zero MAC address for VFs. This removes the
existing MAC address and allows the VF to use a random address. Libvirt
does this normally when removing a VF from a VM.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VFs are being reset, there is a brief window of time when they
cannot be configured because they don't have a VSI to configure. If
a script is quick, it can fall through that window. To avoid
defenestration, log a useful error message and return -EAGAIN.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes on module reload and reconnect to ibss a deauth from
other station can be received. This is treated as a link down but
for ibss this is wrong. It will close the interface and no data
is possible. Ignore the firmware generated link down events in
ibss mode, as ibss is always teared down by cfg80211.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The btcoex uses a timeout which was in milliseconds and got
converted to jiffies upon using timer api. Instead, convert
it to jiffies and treat it as such further.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead to having macro definition for millisecond timeout have
the definition directly in jiffies. This makes the unit of the
value immediately clear and may result in code that is bit more
compact.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_sdio_wd_timer() has wdtick parameter. However, it
is only called with two values and as such the parameter is replaced
with boolean value indicating the timer should be active or not.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function prototype forward declarations are to be avoided. This
patch shuffles some of the functions so the forward declarations
can be removed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dmi_ver wasn't updated correctly before the dmi_decode method run
to save the uuid.
That resulted in "dmidecode -s system-uuid" and
/sys/class/dmi/id/product_uuid disagreeing. The latter was buggy and
this fixes it.
Reported-by: Federico Simoncelli <fsimonce@redhat.com>
Fixes: 9f9c9cbb60 ("drivers/firmware/dmi_scan.c: fetch dmi version from SMBIOS if it exists")
Fixes: 79bae42d51 ("dmi_scan: refactor dmi_scan_machine(), {smbios,dmi}_present()")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The BSP team noticed that there is spin/mutex lock issue on sh-sci when
CPUFREQ is used. The issue is that the notifier function may call
mutex_lock() while the spinlock is held, which can lead to a BUG().
This may happen if CPUFREQ is changed while another CPU calls
clk_get_rate().
Taking the spinlock was added to the notifier function in commit
e552de2413 ("sh-sci: add platform device private data"), to
protect the list of serial ports against modification during traversal.
At that time the Common Clock Framework didn't exist yet, and
clk_get_rate() just returned clk->rate without taking a mutex.
Note that since commit d535a2305f ("serial: sh-sci: Require a
device per port mapping."), there's no longer a list of serial ports to
traverse, and taking the spinlock became superfluous.
To fix the issue, just remove the cpufreq notifier:
1. The notifier doesn't work correctly: all it does is update stored
clock rates; it does not update the divider in the hardware.
The divider will only be updated when calling sci_set_termios().
I believe this was broken back in 2004, when the old
drivers/char/sh-sci.c driver (where the notifier did update the
divider) was replaced by drivers/serial/sh-sci.c (where the
notifier just updated port->uartclk).
Cfr. full-history-linux commits 6f8deaef2e9675d9 ("[PATCH] sh: port
sh-sci driver to the new API") and 3f73fe878dc9210a ("[PATCH]
Remove old sh-sci driver").
2. On modern SoCs, the sh-sci parent clock rate is no longer related
to the CPU clock rate anyway, so using a cpufreq notifier is
futile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert writes:
Summary:
- Clean up the naming of clocks in the sh-sci driver and its DT bindings,
- Add support for the optional external clock on (H)SCI(F), where this pin
can serve as a clock input,
- Add support for the optional clock sources for the Baud Rate
Generator for External Clock (BRG), as found on some SCIF variants
and on HSCIF.
Another iscsi target that cannot handle large IOs, but does not tell us
a limit.
The Synology iSCSI targets report:
Block limits VPD page (SBC):
Write same no zero (WSNZ): 0
Maximum compare and write length: 0 blocks
Optimal transfer length granularity: 0 blocks
Maximum transfer length: 0 blocks
Optimal transfer length: 0 blocks
Maximum prefetch length: 0 blocks
Maximum unmap LBA count: 0
Maximum unmap block descriptor count: 0
Optimal unmap granularity: 0
Unmap granularity alignment valid: 0
Unmap granularity alignment: 0
Maximum write same length: 0x0 blocks
and the size of the command it can handle seems to depend on how much
memory it can allocate at the time. This results in IO errors when
handling large IOs. This patch just has us use the old 1024 default
sectors for this target by adding it to the scsi blacklist. We do not
have good contacs with this vendors, so I have not been able to try and
fix on their side.
I have posted this a long while back, but it was not merged. This
version just fixes it up for merge/patch failures in the original
version.
Reported-by: Ancoron Luciferis <ancoron.luciferis@googlemail.com>
Reported-by: Michael Meyers <steltek@tcnnet.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org> # 4.1+
Dmitry reported that he was able to reproduce the WARN_ON_ONCE that
fires in locks_free_lock_context when the flc_posix list isn't empty.
The problem turns out to be that we're basically rebuilding the
file_lock from scratch in fcntl_setlk when we discover that the setlk
has raced with a close. If the l_whence field is SEEK_CUR or SEEK_END,
then we may end up with fl_start and fl_end values that differ from
when the lock was initially set, if the file position or length of the
file has changed in the interim.
Fix this by just reusing the same lock request structure, and simply
override fl_type value with F_UNLCK as appropriate. That ensures that
we really are unlocking the lock that was initially set.
While we're there, make sure that we do pop a WARN_ON_ONCE if the
removal ever fails. Also return -EBADF in this event, since that's
what we would have returned if the close had happened earlier.
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Fixes: c293621bbf (stale POSIX lock handling)
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
Commit da1f026b53 ("Keyboard: omap-keypad:
use matrix_keypad.h") switched the driver to use matrix keypad
infrastructure, which made array of keycodes to be unsigned short, and
caused the test for negativity never trigger. This leads to the following
static checker warning:
drivers/input/keyboard/omap-keypad.c:158 omap_kp_tasklet()
warn: 'keycodes[]' is never negative.
Given that we did not care about this check for a few years already let's
simply remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove write to REG_IRQCLR and REG_IRQWAKEUP in interrupt handler for
IRQENB_HW_PEN as the resume handler should and does clear REG_IRQWAKEUP.
IRQENB_HW_PEN bit is set in irqclr so that all interrupts get cleared
later so let IRQENB_HW_PEN be cleared by that.
Without this patch wakeup events from TSC_ADC do not work because pending
interrupts in TSC_ADC were causing HW_PEN interrupt, needed for wake from
suspend modes, to get disabled immediately by IRQ handler after being
enabled and preventing wake from happening.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For large sparse or fragmented files, checking every single entry in
the bmapbt on every operation is prohibitively expensive. Especially
as such checks rarely discover problems during normal operations on
high extent coutn files. Our regression tests don't tend to exercise
files with hundreds of thousands to millions of extents, so mostly
this isn't noticed.
However, trying to run things like xfs_mdrestore of large filesystem
dumps on a debug kernel quickly becomes impossible as the CPU is
completely burnt up repeatedly walking the sparse file bmapbt that
is generated for every allocation that is made.
Hence, if the file has more than 10,000 extents, just don't bother
with walking the tree to check it exhaustively. The btree code has
checks that ensure that the newly inserted/removed/modified record
is correctly ordered, so the entrie tree walk in thses cases has
limited additional value.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
This allows us to see page cache driven readahead in action as it
passes through XFS. This helps to understand buffered read
throughput problems such as readahead IO IO sizes being too small
for the underlying device to reach max throughput.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Have dev_pm_ops.prepare return 1 for USB devices and ports so that USB
devices can remain runtime-suspended when the system goes to a sleep
state, if their wakeup state is correct and they have runtime PM enabled.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a suitable prepare callback cannot be found for a given device and
its driver has no PM callbacks at all, assume that it can go direct to
complete when the system goes to sleep.
The reason for this is that there's lots of devices in a system that do
no PM at all and there's no reason for them to prevent their ancestors
to do direct_complete if they can support it.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds a function that sets the pointer to dev_pm_domain in struct device
and that warns if the device has already finished probing. The reason
why we want to enforce that is because in the general case that can
cause problems and also that we can simplify code quite a bit if we can
always assume that.
This patch also changes all current code that directly sets the
dev.pm_domain pointer.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Adds a function that tells whether a device is already bound to a
driver.
This is needed to warn when there is an attempt to change the PM domain
of a device that has finished probing already. The reason why we want to
enforce that is because in the general case that can cause problems and
also that we can simplify code quite a bit if we can always assume that.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a new notification BUS_NOTIFY_DRIVER_NOT_BOUND that is issued when
driver fails during binding. In such case pm_clk_notify(), when PM_CLK=n,
leaves clocks enabled. Undo operations that have been done in
BUS_NOTIFY_BIND_DRIVER case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The dn->name is expected to be used as a literal, so add the missing
"%s".
Fixes: 263b4c1a64 (ACPI / property: Expose data-only subnodes via sysfs)
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
