Since 6 GHz band has around 60 channels and more strict rules for
active probing. Reduced neighbor report can be used to reduce the
channels we scan and get specific target BSS info to probe for.
Declare flag WIPHY_FLAG_SPLIT_SCAN_6GHZ so the scan request could be
divided into two portions: legacy bands and 6 GHz bands. So RNR
information from legacy bands could later be used when 6 GHz scan.
When the scan flag NL80211_SCAN_FLAG_COLOCATED_6GHZ is set, cfg80211
will pass down a reduced channel set which contains PSCs and non-PSC
with RNR info received in the 2 GHz/5 GHz band. This reduces the
scan duration by allowing us to only scan for channels in which APs
are currently operating.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230217120007.8835-1-pkshih@realtek.com
Convert gfs2_page_add_databufs() to folios and rename it to
gfs2_trans_add_databufs().
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
The ->writepage() and ->writepages() operations are supposed to write
entire pages. However, on filesystems with a block size smaller than
PAGE_SIZE, __gfs2_jdata_writepage() only adds the first block to the
current transaction instead of adding the entire page. Fix that.
Fixes: 18ec7d5c3f ("[GFS2] Make journaled data files identical to normal files on disk")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Most but not all PWMs drive the PWM pin to its inactive state when
disabled. However if there is no enable_gpio and no regulator the PWM
must drive the inactive state to actually disable the backlight.
So keep the PWM on in this case.
Note that to determine if there is a regulator some effort is required
because it might happen that there isn't actually one but the regulator
core gave us a dummy. (A nice side effect is that this makes the
regulator actually optional even on fully constrained systems.)
This fixes backlight disabling e.g. on i.MX6 when an inverted PWM is
used.
Hint for the future: If this change results in a regression, the bug is
in the lowlevel PWM driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230120120018.161103-3-u.kleine-koenig@pengutronix.de
When the function pwm_backlight_update_status() was called with
brightness > 0, pwm_get_state() was called twice (once directly and once
in compute_duty_cycle). Also pwm_apply_state() was called twice (once in
pwm_backlight_power_on() and once directly).
Optimize this to do both calls only once.
Note that with this affects the order of regulator and PWM setup. It's
not expected to have a relevant effect on hardware. The rationale for
this is that the regulator (and the GPIO) are reasonable to switch in
pwm_backlight_power_on()/pwm_backlight_power_off() but the PWM has
nothing to do with power. (The post_pwm_on_delay and pwm_off_delay are
still there though.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230120120018.161103-2-u.kleine-koenig@pengutronix.de
Correct the struct name and add a short struct description to fix the
kernel-doc notation.
Prevents this kernel-doc warning:
drivers/video/backlight/sky81452-backlight.c:64: warning: expecting prototype for struct sky81452_platform_data. Prototype was for struct sky81452_bl_platform_data instead
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230113064118.30169-1-rdunlap@infradead.org
When ath11k runs into internal errors upon suspend,
it returns an error code to pci_pm_suspend, which
aborts the entire system suspend.
The driver should not abort system suspend, but should
keep its internal errors to itself, and allow the system
to suspend. Otherwise, a user can suspend a laptop
by closing the lid and sealing it into a case, assuming
that is will suspend, rather than heating up and draining
the battery when in transit.
In practice, the ath11k device seems to have plenty of transient
errors, and subsequent suspend cycles after this failure
often succeed.
https://bugzilla.kernel.org/show_bug.cgi?id=216968
Fixes: d1b0c33850 ("ath11k: implement suspend for QCA6390 PCI devices")
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230201183201.14431-1-len.brown@intel.com
Fix sleep in atomic context warning detected by Smatch static checker
analyzer.
Following the locking pattern for peer_rhash_add lock tbl_mtx_lock mutex
always even if sta is not transitioning to another band.
This is peer_add function and a more secure locking should not cause
performance regression.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: d673cb6fe6 ("wifi: ath11k: fix peer addition/deletion error on sta band migration")
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230209222622.1751-1-ansuelsmth@gmail.com
NAPI poll can be done in threaded context along with soft irq
context. Threaded context can be scheduled efficiently, thus
creating less of bottleneck during Rx processing. This patch is
to enable threaded NAPI on ath10k driver.
Based on testing, it was observed that on WCN3990, the CPU0 reaches
100% utilization when napi runs in softirq context. At the same
time the other CPUs are at low consumption percentage. This
does not allow device to reach its maximum throughput potential.
After enabling threaded napi, CPU load is balanced across all CPUs
and following improvments were observed:
- UDP_RX increase by ~22-25%
- TCP_RX increase by ~15%
Here are some of the additional raw data with and without threaded napi:
==================================================
udp_rx(Without threaded NAPI)
435.98+-5.16 : Channel 44
439.06+-0.66 : Channel 157
udp_rx(With threaded NAPI)
509.73+-41.03 : Channel 44
549.97+-7.62 : Channel 157
===================================================
udp_tx(Without threaded NAPI)
461.31+-0.69 : Channel 44
461.46+-0.78 : Channel 157
udp_tx(With threaded NAPI)
459.20+-0.77 : Channel 44
459.78+-1.08 : Channel 157
===================================================
tcp_rx(Without threaded NAPI)
472.63+-2.35 : Channel 44
469.29+-6.31 : Channel 157
tcp_rx(With threaded NAPI)
498.49+-2.44 : Channel 44
541.14+-40.65 : Channel 157
===================================================
tcp_tx(Without threaded NAPI)
317.34+-2.37 : Channel 44
317.01+-2.56 : Channel 157
tcp_tx(With threaded NAPI)
371.34+-2.36 : Channel 44
376.95+-9.40 : Channel 157
===================================================
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2-00696-QCAHLSWMTPL-1
Signed-off-by: Abhishek Kumar <kuabhs@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230203000116.v2.1.I5bb9c164a2d2025655dee810b983e01ecd81c14e@changeid
This loop checks that i < max at the start of loop but then it does
i++ which could put it past the end of the array. It's harmless to
check again and prevent a potential out of bounds.
Fixes: 1048643ea9 ("ath5k: Clean up eeprom parsing and add missing calibration data")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/Y+D9hPQrHfWBJhXz@kili
As of commit a1a2b7125e ("of/platform: Drop static setup of IRQ
resource from DT core"), we need to use platform_get_irq() instead of
platform_get_resource() to get our IRQs because
platform_get_resource() simply won't get them anymore.
This was already fixed in several other Atheros WiFi drivers,
apparently in response to Zeal Robot reports. An example of another
fix is commit 9503a1fc12 ("ath9k: Use platform_get_irq() to get the
interrupt"). ath5k seems to have been missed in this effort, though.
Fixes: a1a2b7125e ("of/platform: Drop static setup of IRQ resource from DT core")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230201084131.v2.2.Ic4f8542b0588d7eb4bc6e322d4af3d2064e84ff0@changeid
As of commit a1a2b7125e ("of/platform: Drop static setup of IRQ
resource from DT core"), we need to use platform_get_irq() instead of
platform_get_resource() to get our IRQs because
platform_get_resource() simply won't get them anymore.
This was already fixed in several other Atheros WiFi drivers,
apparently in response to Zeal Robot reports. An example of another
fix is commit 9503a1fc12 ("ath9k: Use platform_get_irq() to get the
interrupt"). ath11k seems to have been missed in this effort, though.
Without this change, WiFi wasn't coming up on my Qualcomm sc7280-based
hardware. Specifically, "platform_get_resource(pdev, IORESOURCE_IRQ,
i)" was failing even for i=0.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: a1a2b7125e ("of/platform: Drop static setup of IRQ resource from DT core")
Fixes: 00402f49d2 ("ath11k: Add support for WCN6750 device")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jun Yu <junyuu@chromium.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230201084131.v2.1.I69cf3d56c97098287fe3a70084ee515098390b70@changeid
Wakeup/release MHI is not needed before pci_read/write for QCN9274.
Since wakeup & release MHI is enabled for all QCN9274 and
WCN7850, below MHI assert is seen in QCN9274
[ 784.906613] BUG: sleeping function called from invalid context at drivers/bus/mhi/host/pm.c:989
[ 784.906633] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 0, name: swapper/3
[ 784.906637] preempt_count: 503, expected: 0
[ 784.906641] RCU nest depth: 0, expected: 0
[ 784.906644] 2 locks held by swapper/3/0:
[ 784.906646] #0: ffff8ed348e429e0 (&ab->ce.ce_lock){+.-.}-{2:2}, at: ath12k_ce_recv_process_cb+0xb3/0x2f0 [ath12k]
[ 784.906664] #1: ffff8ed348e491f0 (&srng->lock_key#3){+.-.}-{2:2}, at: ath12k_ce_recv_process_cb+0xfb/0x2f0 [ath12k]
[ 784.906678] Preemption disabled at:
[ 784.906680] [<0000000000000000>] 0x0
[ 784.906686] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G W O 6.1.0-rc2+ #3
[ 784.906688] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0056.2019.0506.1527 05/06/2019
[ 784.906690] Call Trace:
[ 784.906691] <IRQ>
[ 784.906693] dump_stack_lvl+0x56/0x7b
[ 784.906698] __might_resched+0x21c/0x270
[ 784.906704] __mhi_device_get_sync+0x7d/0x1c0 [mhi]
[ 784.906714] mhi_device_get_sync+0xd/0x20 [mhi]
[ 784.906719] ath12k_pci_write32+0x75/0x170 [ath12k]
[ 784.906729] ath12k_hal_srng_access_end+0x55/0xc0 [ath12k]
[ 784.906737] ath12k_ce_recv_process_cb+0x1f3/0x2f0 [ath12k]
[ 784.906776] ? ath12k_pci_ce_tasklet+0x11/0x30 [ath12k]
[ 784.906788] ath12k_pci_ce_tasklet+0x11/0x30 [ath12k]
[ 784.906813] tasklet_action_common.isra.18+0xb7/0xe0
[ 784.906820] __do_softirq+0xd0/0x4c9
[ 784.906826] irq_exit_rcu+0x88/0xe0
[ 784.906828] common_interrupt+0xa5/0xc0
[ 784.906831] </IRQ>
[ 784.906832] <TASK>
Adding function callbacks for MHI wakeup and release operations.
QCN9274 does not need wakeup/release, function callbacks are initialized
to NULL. In case of WCN7850, shadow registers are used to access rings.
Since, shadow register's offset is less than ACCESS_ALWAYS_OFF,
mhi_device_get_sync() or mhi_device_put() to wakeup
and release mhi will not be called during service ring accesses.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-03171-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230123095141.5310-1-quic_rgnanase@quicinc.com
Initial support of HID-BPF (Benjamin Tissoires)
The history is a little long for this series, as it was intended to be
sent for v6.2. However some last minute issues forced us to postpone it
to v6.3.
Conflicts:
* drivers/hid/i2c-hid/Kconfig:
commit bf7660dab3 ("HID: stop drivers from selecting CONFIG_HID")
conflicts with commit 2afac81dd1 ("HID: fix I2C_HID not selected
when I2C_HID_OF_ELAN is")
the resolution is simple enough: just drop the "default" and "select"
lines as the new commit from Arnd is doing
