[ Upstream commit 75c1edf23b ]
Same trigger condition as commit 86434744. When setsockopt runs
in parallel to a connect(), and switch the socket into fallback
mode. Then the sk_refcnt is incremented in smc_connect(), but
its state stay in SMC_INIT (NOT SMC_ACTIVE). This cause the
corresponding sk_refcnt decrement in __smc_release() will not be
performed.
Fixes: 86434744fe ("net/smc: add fallback check to connect()")
Signed-off-by: liuyacan <liuyacan@corp.netease.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a3dedcf18 ]
Fix the decision on when to generate an IDLE ACK by keeping a count of the
number of packets we've received, but not yet soft-ACK'd, and the number of
packets we've processed, but not yet hard-ACK'd, rather than trying to keep
track of which DATA sequence numbers correspond to those points.
We then generate an ACK when either counter exceeds 2. The counters are
both cleared when we transcribe the information into any sort of ACK packet
for transmission. IDLE and DELAY ACKs are skipped if both counters are 0
(ie. no change).
Fixes: 805b21b929 ("rxrpc: Send an ACK after every few DATA packets we receive")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81524b6312 ]
The previousPacket field in the rx ACK packet should never go backwards -
it's now the highest DATA sequence number received, not the last on
received (it used to be used for out of sequence detection).
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8940ba3cfe ]
Fix accidental overlapping of Rx-phase ACK accounting with Tx-phase ACK
accounting through variables shared between the two. call->acks_* members
refer to ACKs received in the Tx phase and call->ackr_* members to ACKs
sent/to be sent during the Rx phase.
Fixes: 1a2391c30c ("rxrpc: Fix detection of out of order acks")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 114af61f88 ]
rxrpc has a timer to trigger resending of unacked data packets in a call.
This is not cancelled when a client call switches to the receive phase on
the basis that most calls don't last long enough for it to ever expire.
However, if it *does* expire after we've started to receive the reply, we
shouldn't then go into trying to retransmit or pinging the server to find
out if an ack got lost.
Fix this by skipping the resend code if we're into receiving the reply to a
client call.
Fixes: 17926a7932 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88e2215975 ]
AF_RXRPC's listen() handler lets you set the backlog up to 32 (if you bump
up the sysctl), but whilst the preallocation circular buffers have 32 slots
in them, one of them has to be a dead slot because we're using CIRC_CNT().
This means that listen(rxrpc_sock, 32) will cause an oops when the socket
is closed because rxrpc_service_prealloc_one() allocated one too many calls
and rxrpc_discard_prealloc() won't then be able to get rid of them because
it'll think the ring is empty. rxrpc_release_calls_on_socket() then tries
to abort them, but oopses because call->peer isn't yet set.
Fix this by setting the maximum backlog to RXRPC_BACKLOG_MAX - 1 to match
the ring capacity.
BUG: kernel NULL pointer dereference, address: 0000000000000086
...
RIP: 0010:rxrpc_send_abort_packet+0x73/0x240 [rxrpc]
Call Trace:
<TASK>
? __wake_up_common_lock+0x7a/0x90
? rxrpc_notify_socket+0x8e/0x140 [rxrpc]
? rxrpc_abort_call+0x4c/0x60 [rxrpc]
rxrpc_release_calls_on_socket+0x107/0x1a0 [rxrpc]
rxrpc_release+0xc9/0x1c0 [rxrpc]
__sock_release+0x37/0xa0
sock_close+0x11/0x20
__fput+0x89/0x240
task_work_run+0x59/0x90
do_exit+0x319/0xaa0
Fixes: 00e907127e ("rxrpc: Preallocate peers, conns and calls for incoming service requests")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Link: https://lists.infradead.org/pipermail/linux-afs/2022-March/005079.html
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aa1e7d15f ]
Connecting the same socket twice consecutively in sco_sock_connect()
could lead to a race condition where two sco_conn objects are created
but only one is associated with the socket. If the socket is closed
before the SCO connection is established, the timer associated with the
dangling sco_conn object won't be canceled. As the sock object is being
freed, the use-after-free problem happens when the timer callback
function sco_sock_timeout() accesses the socket. Here's the call trace:
dump_stack+0x107/0x163
? refcount_inc+0x1c/
print_address_description.constprop.0+0x1c/0x47e
? refcount_inc+0x1c/0x7b
kasan_report+0x13a/0x173
? refcount_inc+0x1c/0x7b
check_memory_region+0x132/0x139
refcount_inc+0x1c/0x7b
sco_sock_timeout+0xb2/0x1ba
process_one_work+0x739/0xbd1
? cancel_delayed_work+0x13f/0x13f
? __raw_spin_lock_init+0xf0/0xf0
? to_kthread+0x59/0x85
worker_thread+0x593/0x70e
kthread+0x346/0x35a
? drain_workqueue+0x31a/0x31a
? kthread_bind+0x4b/0x4b
ret_from_fork+0x1f/0x30
Link: https://syzkaller.appspot.com/bug?extid=2bef95d3ab4daa10155b
Reported-by: syzbot+2bef95d3ab4daa10155b@syzkaller.appspotmail.com
Fixes: e1dee2c1de ("Bluetooth: fix repeated calls to sco_sock_kill")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Reviewed-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ba68c5192 ]
If at the end of rxrpc sendmsg() or rxrpc_kernel_send_data() the call that
was being given data was aborted remotely or otherwise failed, return an
error rather than returning the amount of data buffered for transmission.
The call (presumably) did not complete, so there's not much point
continuing with it. AF_RXRPC considers it "complete" and so will be
unwilling to do anything else with it - and won't send a notification for
it, deeming the return from sendmsg sufficient.
Not returning an error causes afs to incorrectly handle a StoreData
operation that gets interrupted by a change of address due to NAT
reconfiguration.
This doesn't normally affect most operations since their request parameters
tend to fit into a single UDP packet and afs_make_call() returns before the
server responds; StoreData is different as it involves transmission of a
lot of data.
This can be triggered on a client by doing something like:
dd if=/dev/zero of=/afs/example.com/foo bs=1M count=512
at one prompt, and then changing the network address at another prompt,
e.g.:
ifconfig enp6s0 inet 192.168.6.2 && route add 192.168.6.1 dev enp6s0
Tracing packets on an Auristor fileserver looks something like:
192.168.6.1 -> 192.168.6.3 RX 107 ACK Idle Seq: 0 Call: 4 Source Port: 7000 Destination Port: 7001
192.168.6.3 -> 192.168.6.1 AFS (RX) 1482 FS Request: Unknown(64538) (64538)
192.168.6.3 -> 192.168.6.1 AFS (RX) 1482 FS Request: Unknown(64538) (64538)
192.168.6.1 -> 192.168.6.3 RX 107 ACK Idle Seq: 0 Call: 4 Source Port: 7000 Destination Port: 7001
<ARP exchange for 192.168.6.2>
192.168.6.2 -> 192.168.6.1 AFS (RX) 1482 FS Request: Unknown(0) (0)
192.168.6.2 -> 192.168.6.1 AFS (RX) 1482 FS Request: Unknown(0) (0)
192.168.6.1 -> 192.168.6.2 RX 107 ACK Exceeds Window Seq: 0 Call: 4 Source Port: 7000 Destination Port: 7001
192.168.6.1 -> 192.168.6.2 RX 74 ABORT Seq: 0 Call: 4 Source Port: 7000 Destination Port: 7001
192.168.6.1 -> 192.168.6.2 RX 74 ABORT Seq: 29321 Call: 4 Source Port: 7000 Destination Port: 7001
The Auristor fileserver logs code -453 (RXGEN_SS_UNMARSHAL), but the abort
code received by kafs is -5 (RX_PROTOCOL_ERROR) as the rx layer sees the
condition and generates an abort first and the unmarshal error is a
consequence of that at the application layer.
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Link: http://lists.infradead.org/pipermail/linux-afs/2021-December/004810.html # v1
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51454ea42c ]
idev->addr_list needs to be protected by idev->lock. However, it is not
always possible to do so while iterating and performing actions on
inet6_ifaddr instances. For example, multiple functions (like
addrconf_{join,leave}_anycast) eventually call down to other functions
that acquire the idev->lock. The current code temporarily unlocked the
idev->lock during the loops, which can cause race conditions. Moving the
locks up is also not an appropriate solution as the ordering of lock
acquisition will be inconsistent with for example mc_lock.
This solution adds an additional field to inet6_ifaddr that is used
to temporarily add the instances to a temporary list while holding
idev->lock. The temporary list can then be traversed without holding
idev->lock. This change was done in two places. In addrconf_ifdown, the
list_for_each_entry_safe variant of the list loop is also no longer
necessary as there is no deletion within that specific loop.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220403231523.45843-1-dossche.niels@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015c44d7bf ]
Since the recent introduction supporting the SM3 and SM4 hash algos for IPsec, the kernel
produces invalid pfkey acquire messages, when these encryption modules are disabled. This
happens because the availability of the algos wasn't checked in all necessary functions.
This patch adds these checks.
Signed-off-by: Thomas Bartschies <thomas.bartschies@cvk.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b2d057560b upstream.
SipHash replaced MD5 in secure_ipv{4,6}_port_ephemeral() via commit
7cd23e5300 ("secure_seq: use SipHash in place of MD5"), but the output
remained truncated to 32-bit only. In order to exploit more bits from the
hash, let's make the functions return the full 64-bit of siphash_3u32().
We also make sure the port offset calculation in __inet_hash_connect()
remains done on 32-bit to avoid the need for div_u64_rem() and an extra
cost on 32-bit systems.
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Moshe Kol <moshe.kol@mail.huji.ac.il>
Cc: Yossi Gilad <yossi.gilad@mail.huji.ac.il>
Cc: Amit Klein <aksecurity@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[SG: Adjusted context]
Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 190cc82489 upstream.
RFC 6056 (Recommendations for Transport-Protocol Port Randomization)
provides good summary of why source selection needs extra care.
David Dworken reminded us that linux implements Algorithm 3
as described in RFC 6056 3.3.3
Quoting David :
In the context of the web, this creates an interesting info leak where
websites can count how many TCP connections a user's computer is
establishing over time. For example, this allows a website to count
exactly how many subresources a third party website loaded.
This also allows:
- Distinguishing between different users behind a VPN based on
distinct source port ranges.
- Tracking users over time across multiple networks.
- Covert communication channels between different browsers/browser
profiles running on the same computer
- Tracking what applications are running on a computer based on
the pattern of how fast source ports are getting incremented.
Section 3.3.4 describes an enhancement, that reduces
attackers ability to use the basic information currently
stored into the shared 'u32 hint'.
This change also decreases collision rate when
multiple applications need to connect() to
different destinations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fbb3abdf22 ]
It is possible to stack bridges on top of each other. Consider the
following which makes use of an Ethernet switch:
br1
/ \
/ \
/ \
br0.11 wlan0
|
br0
/ | \
p1 p2 p3
br0 is offloaded to the switch. Above br0 is a vlan interface, for
vlan 11. This vlan interface is then a slave of br1. br1 also has a
wireless interface as a slave. This setup trunks wireless lan traffic
over the copper network inside a VLAN.
A frame received on p1 which is passed up to the bridge has the
skb->offload_fwd_mark flag set to true, indicating that the switch has
dealt with forwarding the frame out ports p2 and p3 as needed. This
flag instructs the software bridge it does not need to pass the frame
back down again. However, the flag is not getting reset when the frame
is passed upwards. As a result br1 sees the flag, wrongly interprets
it, and fails to forward the frame to wlan0.
When passing a frame upwards, clear the flag. This is the Rx
equivalent of br_switchdev_frame_unmark() in br_dev_xmit().
Fixes: f1c2eddf4c ("bridge: switchdev: Use an helper to clear forward mark")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220518005840.771575-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dc2a5a8f6 ]
If skb_clone() returns null pointer, pfkey_broadcast() will
return error.
Therefore, it should be better to check the return value of
pfkey_broadcast() and return error if fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23dd458135 ]
There are sleep in atomic context bugs when the request to secure
element of st-nci is timeout. The root cause is that nci_skb_alloc
with GFP_KERNEL parameter is called in st_nci_se_wt_timeout which is
a timer handler. The call paths that could trigger bugs are shown below:
(interrupt context 1)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_skb_alloc(..., GFP_KERNEL) //may sleep
(interrupt context 2)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_send_data
nci_queue_tx_data_frags
nci_skb_alloc(..., GFP_KERNEL) //may sleep
This patch changes allocation mode of nci_skb_alloc from GFP_KERNEL to
GFP_ATOMIC in order to prevent atomic context sleeping. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
Fixes: ed06aeefda ("nfc: st-nci: Rename st21nfcb to st-nci")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220517012530.75714-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d42d54a7d ]
syzbot was able to trigger an Out-of-Bound on the pedit action:
UBSAN: shift-out-of-bounds in net/sched/act_pedit.c:238:43
shift exponent 1400735974 is too large for 32-bit type 'unsigned int'
CPU: 0 PID: 3606 Comm: syz-executor151 Not tainted 5.18.0-rc5-syzkaller-00165-g810c2f0a3f86 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x50 lib/ubsan.c:151
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x187 lib/ubsan.c:322
tcf_pedit_init.cold+0x1a/0x1f net/sched/act_pedit.c:238
tcf_action_init_1+0x414/0x690 net/sched/act_api.c:1367
tcf_action_init+0x530/0x8d0 net/sched/act_api.c:1432
tcf_action_add+0xf9/0x480 net/sched/act_api.c:1956
tc_ctl_action+0x346/0x470 net/sched/act_api.c:2015
rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5993
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:725
____sys_sendmsg+0x6e2/0x800 net/socket.c:2413
___sys_sendmsg+0xf3/0x170 net/socket.c:2467
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2496
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fe36e9e1b59
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffef796fe88 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fe36e9e1b59
RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000003
RBP: 00007fe36e9a5d00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe36e9a5d90
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
The 'shift' field is not validated, and any value above 31 will
trigger out-of-bounds. The issue predates the git history, but
syzbot was able to trigger it only after the commit mentioned in
the fixes tag, and this change only applies on top of such commit.
Address the issue bounding the 'shift' value to the maximum allowed
by the relevant operator.
Reported-and-tested-by: syzbot+8ed8fc4c57e9dcf23ca6@syzkaller.appspotmail.com
Fixes: 8b796475fd ("net/sched: act_pedit: really ensure the skb is writable")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
From: Trond Myklebust <trond.myklebust@hammerspace.com>
commit f00432063d upstream.
We must ensure that all sockets are closed before we call xprt_free()
and release the reference to the net namespace. The problem is that
calling fput() will defer closing the socket until delayed_fput() gets
called.
Let's fix the situation by allowing rpciod and the transport teardown
code (which runs on the system wq) to call __fput_sync(), and directly
close the socket.
Reported-by: Felix Fu <foyjog@gmail.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Fixes: a73881c96d ("SUNRPC: Fix an Oops in udp_poll()")
Cc: stable@vger.kernel.org # 5.1.x: 3be232f11a: SUNRPC: Prevent immediate close+reconnect
Cc: stable@vger.kernel.org # 5.1.x: 89f42494f9: SUNRPC: Don't call connect() more than once on a TCP socket
Cc: stable@vger.kernel.org # 5.1.x
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
[meenashanmugam: Fix merge conflict in xprt_connect]
Signed-off-by: Meena Shanmugam <meenashanmugam@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Trond Myklebust <trond.myklebust@hammerspace.com>
commit 89f42494f9 upstream.
Avoid socket state races due to repeated calls to ->connect() using the
same socket. If connect() returns 0 due to the connection having
completed, but we are in fact in a closing state, then we may leave the
XPRT_CONNECTING flag set on the transport.
Reported-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Fixes: 3be232f11a ("SUNRPC: Prevent immediate close+reconnect")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
[meenashanmugam: Fix merge conflict in xs_tcp_setup_socket]
Signed-off-by: Meena Shanmugam <meenashanmugam@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1a7ac6f3b upstream.
When ping_group_range is updated, 'ping' uses the DGRAM ICMP socket,
instead of an IP raw socket. In this case, 'ping' is unable to bind its
socket to a local address owned by a vrflite.
Before the patch:
$ sysctl -w net.ipv4.ping_group_range='0 2147483647'
$ ip link add blue type vrf table 10
$ ip link add foo type dummy
$ ip link set foo master blue
$ ip link set foo up
$ ip addr add 192.168.1.1/24 dev foo
$ ip addr add 2001::1/64 dev foo
$ ip vrf exec blue ping -c1 -I 192.168.1.1 192.168.1.2
ping: bind: Cannot assign requested address
$ ip vrf exec blue ping6 -c1 -I 2001::1 2001::2
ping6: bind icmp socket: Cannot assign requested address
CC: stable@vger.kernel.org
Fixes: 1b69c6d0ae ("net: Introduce L3 Master device abstraction")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b796475fd ]
Currently pedit tries to ensure that the accessed skb offset
is writable via skb_unclone(). The action potentially allows
touching any skb bytes, so it may end-up modifying shared data.
The above causes some sporadic MPTCP self-test failures, due to
this code:
tc -n $ns2 filter add dev ns2eth$i egress \
protocol ip prio 1000 \
handle 42 fw \
action pedit munge offset 148 u8 invert \
pipe csum tcp \
index 100
The above modifies a data byte outside the skb head and the skb is
a cloned one, carrying a TCP output packet.
This change addresses the issue by keeping track of a rough
over-estimate highest skb offset accessed by the action and ensuring
such offset is really writable.
Note that this may cause performance regressions in some scenarios,
but hopefully pedit is not in the critical path.
Fixes: db2c24175d ("act_pedit: access skb->data safely")
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/1fcf78e6679d0a287dd61bb0f04730ce33b3255d.1652194627.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5076fe404 ]
netlink_recvmsg() does not need to change transport header.
If transport header was needed, it should have been reset
by the producer (netlink_dump()), not the consumer(s).
The following trace probably happened when multiple threads
were using MSG_PEEK.
BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg
write to 0xffff88811e9f15b2 of 2 bytes by task 32012 on cpu 1:
skb_reset_transport_header include/linux/skbuff.h:2760 [inline]
netlink_recvmsg+0x1de/0x790 net/netlink/af_netlink.c:1978
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
__sys_recvfrom+0x204/0x2c0 net/socket.c:2097
__do_sys_recvfrom net/socket.c:2115 [inline]
__se_sys_recvfrom net/socket.c:2111 [inline]
__x64_sys_recvfrom+0x74/0x90 net/socket.c:2111
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
write to 0xffff88811e9f15b2 of 2 bytes by task 32005 on cpu 0:
skb_reset_transport_header include/linux/skbuff.h:2760 [inline]
netlink_recvmsg+0x1de/0x790 net/netlink/af_netlink.c:1978
____sys_recvmsg+0x162/0x2f0
___sys_recvmsg net/socket.c:2674 [inline]
__sys_recvmsg+0x209/0x3f0 net/socket.c:2704
__do_sys_recvmsg net/socket.c:2714 [inline]
__se_sys_recvmsg net/socket.c:2711 [inline]
__x64_sys_recvmsg+0x42/0x50 net/socket.c:2711
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffff -> 0x0000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 32005 Comm: syz-executor.4 Not tainted 5.18.0-rc1-syzkaller-00328-ge1f700ebd6be-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220505161946.2867638-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86af062f40 ]
Currently MBSSID parameters in struct ieee80211_bss_conf
are not reset upon connection. This could be problematic
with some drivers in a scenario where the device first
connects to a non-transmit BSS and then connects to a
transmit BSS of a Multi BSS AP. The MBSSID parameters
which are set after connecting to a non-transmit BSS will
not be reset and the same parameters will be passed on to
the driver during the subsequent connection to a transmit
BSS of a Multi BSS AP.
For example, firmware running on the ath11k device uses the
Multi BSS data for tracking the beacon of a non-transmit BSS
and reports the driver when there is a beacon miss. If we do
not reset the MBSSID parameters during the subsequent
connection to a transmit BSS, then the driver would have
wrong MBSSID data and FW would be looking for an incorrect
BSSID in the MBSSID beacon of a Multi BSS AP and reports
beacon loss leading to an unstable connection.
Reset the MBSSID parameters upon every connection to solve this
problem.
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Link: https://lore.kernel.org/r/20220428052744.27040-1-quic_mpubbise@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a063f2fba3 ]
The receiving interface might have used GRO to receive more fragments than
MAX_SKB_FRAGS fragments. In this case, these will not be stored in
skb_shinfo(skb)->frags but merged into the frag list.
batman-adv relies on the function skb_split to split packets up into
multiple smaller packets which are not larger than the MTU on the outgoing
interface. But this function cannot handle frag_list entries and is only
operating on skb_shinfo(skb)->frags. If it is still trying to split such an
skb and xmit'ing it on an interface without support for NETIF_F_FRAGLIST,
then validate_xmit_skb() will try to linearize it. But this fails due to
inconsistent information. And __pskb_pull_tail will trigger a BUG_ON after
skb_copy_bits() returns an error.
In case of entries in frag_list, just linearize the skb before operating on
it with skb_split().
Reported-by: Felix Kaechele <felix@kaechele.ca>
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Felix Kaechele <felix@kaechele.ca>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 103a2f3255 upstream.
Set a size limit of 8 bytes of the written buffer to "hdev->name"
including the terminating null byte, as the size of "hdev->name" is 8
bytes. If an id value which is greater than 9999 is allocated,
then the "snprintf(hdev->name, sizeof(hdev->name), "hci%d", id)"
function call would lead to a truncation of the id value in decimal
notation.
Set an explicit maximum id parameter in the id allocation function call.
The id allocation function defines the maximum allocated id value as the
maximum id parameter value minus one. Therefore, HCI_MAX_ID is defined
as 10000.
Signed-off-by: Itay Iellin <ieitayie@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9995b408f1 upstream.
There are two reasons for addrconf_notify() to be called with NETDEV_DOWN:
either the network device is actually going down, or IPv6 was disabled
on the interface.
If either of them stays down while the other is toggled, we repeatedly
call the code for NETDEV_DOWN, including ipv6_mc_down(), while never
calling the corresponding ipv6_mc_up() in between. This will cause a
new entry in idev->mc_tomb to be allocated for each multicast group
the interface is subscribed to, which in turn leaks one struct ifmcaddr6
per nontrivial multicast group the interface is subscribed to.
The following reproducer will leak at least $n objects:
ip addr add ff2e::4242/32 dev eth0 autojoin
sysctl -w net.ipv6.conf.eth0.disable_ipv6=1
for i in $(seq 1 $n); do
ip link set up eth0; ip link set down eth0
done
Joining groups with IPV6_ADD_MEMBERSHIP (unprivileged) or setting the
sysctl net.ipv6.conf.eth0.forwarding to 1 (=> subscribing to ff02::2)
can also be used to create a nontrivial idev->mc_list, which will the
leak objects with the right up-down-sequence.
Based on both sources for NETDEV_DOWN events the interface IPv6 state
should be considered:
- not ready if the network interface is not ready OR IPv6 is disabled
for it
- ready if the network interface is ready AND IPv6 is enabled for it
The functions ipv6_mc_up() and ipv6_down() should only be run when this
state changes.
Implement this by remembering when the IPv6 state is ready, and only
run ipv6_mc_down() if it actually changed from ready to not ready.
The other direction (not ready -> ready) already works correctly, as:
- the interface notification triggered codepath for NETDEV_UP /
NETDEV_CHANGE returns early if ipv6 is disabled, and
- the disable_ipv6=0 triggered codepath skips fully initializing the
interface as long as addrconf_link_ready(dev) returns false
- calling ipv6_mc_up() repeatedly does not leak anything
Fixes: 3ce62a84d5 ("ipv6: exit early in addrconf_notify() if IPv6 is disabled")
Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
[jnixdorf: context updated for bpo to v4.19/v5.4]
Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4071bf121d upstream.
There are sleep in atomic bug that could cause kernel panic during
firmware download process. The root cause is that nlmsg_new with
GFP_KERNEL parameter is called in fw_dnld_timeout which is a timer
handler. The call trace is shown below:
BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265
Call Trace:
kmem_cache_alloc_node
__alloc_skb
nfc_genl_fw_download_done
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
...
The nlmsg_new with GFP_KERNEL parameter may sleep during memory
allocation process, and the timer handler is run as the result of
a "software interrupt" that should not call any other function
that could sleep.
This patch changes allocation mode of netlink message from GFP_KERNEL
to GFP_ATOMIC in order to prevent sleep in atomic bug. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
Fixes: 9674da8759 ("NFC: Add firmware upload netlink command")
Fixes: 9ea7187c53 ("NFC: netlink: Rename CMD_FW_UPLOAD to CMD_FW_DOWNLOAD")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220504055847.38026-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da5c0f1192 upstream.
The device_is_registered() in nfc core is used to check whether
nfc device is registered in netlink related functions such as
nfc_fw_download(), nfc_dev_up() and so on. Although device_is_registered()
is protected by device_lock, there is still a race condition between
device_del() and device_is_registered(). The root cause is that
kobject_del() in device_del() is not protected by device_lock.
(cleanup task) | (netlink task)
|
nfc_unregister_device | nfc_fw_download
device_del | device_lock
... | if (!device_is_registered)//(1)
kobject_del//(2) | ...
... | device_unlock
The device_is_registered() returns the value of state_in_sysfs and
the state_in_sysfs is set to zero in kobject_del(). If we pass check in
position (1), then set zero in position (2). As a result, the check
in position (1) is useless.
This patch uses bool variable instead of device_is_registered() to judge
whether the nfc device is registered, which is well synchronized.
Fixes: 3e256b8f8d ("NFC: add nfc subsystem core")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3d0562d4d upstream.
This reverts commit 7073ea8799.
We must not try to connect the socket while the transport is under
construction, because the mechanisms to safely tear it down are not in
place. As the code stands, we end up leaking the sockets on a connection
error.
Reported-by: wanghai (M) <wanghai38@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 743b83f15d upstream.
Check if the incoming interface is available and NFT_BREAK
in case neither skb->sk nor input device are set.
Because nf_sk_lookup_slow*() assume packet headers are in the
'in' direction, use in postrouting is not going to yield a meaningful
result. Same is true for the forward chain, so restrict the use
to prerouting, input and output.
Use in output work if a socket is already attached to the skb.
Fixes: 554ced0a6e ("netfilter: nf_tables: add support for native socket matching")
Reported-and-tested-by: Topi Miettinen <toiwoton@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a0df71948e ]
Calling tls_append_frag when max_open_record_len == record->len might
add an empty fragment to the TLS record if the call happens to be on the
page boundary. Normally tls_append_frag coalesces the zero-sized
fragment to the previous one, but not if it's on page boundary.
If a resync happens then, the mlx5 driver posts dump WQEs in
tx_post_resync_dump, and the empty fragment may become a data segment
with byte_count == 0, which will confuse the NIC and lead to a CQE
error.
This commit fixes the described issue by skipping tls_append_frag on
zero size to avoid adding empty fragments. The fix is not in the driver,
because an empty fragment is hardly the desired behavior.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220426154949.159055-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bfe744ff1 ]
I had this bug sitting for too long in my pile, it is time to fix it.
Thanks to Doug Porter for reminding me of it!
We had various attempts in the past, including commit
0cbe6a8f08 ("tcp: remove SOCK_QUEUE_SHRUNK"),
but the issue is that TCP stack currently only generates
EPOLLOUT from input path, when tp->snd_una has advanced
and skb(s) cleaned from rtx queue.
If a flow has a big RTT, and/or receives SACKs, it is possible
that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0
and no more data can be sent until tp->snd_una finally advances.
What is needed is to also check if POLLOUT needs to be generated
whenever tp->snd_nxt is advanced, from output path.
This bug triggers more often after an idle period, as
we do not receive ACK for at least one RTT. tcp_notsent_lowat
could be a fraction of what CWND and pacing rate would allow to
send during this RTT.
In a followup patch, I will remove the bogus call
to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED)
from tcp_check_space(). Fact that we have decided to generate
an EPOLLOUT does not mean the application has immediately
refilled the transmit queue. This optimistic call
might have been the reason the bug seemed not too serious.
Tested:
200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2]
$ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat
$ cat bench_rr.sh
SUM=0
for i in {1..10}
do
V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"`
echo $V
SUM=$(($SUM + $V))
done
echo SUM=$SUM
Before patch:
$ bench_rr.sh
130000000
80000000
140000000
140000000
140000000
140000000
130000000
40000000
90000000
110000000
SUM=1140000000
After patch:
$ bench_rr.sh
430000000
590000000
530000000
450000000
450000000
350000000
450000000
490000000
480000000
460000000
SUM=4680000000 # This is 410 % of the value before patch.
Fixes: c9bee3b7fd ("tcp: TCP_NOTSENT_LOWAT socket option")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Doug Porter <dsp@fb.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff827beb70 ]
For GRE and GRETAP devices, currently o_seqno starts from 1 in native
mode. According to RFC 2890 2.2., "The first datagram is sent with a
sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see gre_fb_xmit(), where tunnel->o_seqno is passed to
gre_build_header() before getting incremented.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e2e65e2e5 ]
In the current implementation, when TCP initiates a connection
to an unavailable [ip,port], ECONNREFUSED will be stored in the
TCP socket, but SMC will not. However, some apps (like curl) use
getsockopt(,,SO_ERROR,,) to get the error information, which makes
them miss the error message and behave strangely.
Fixes: 50717a37db ("net/smc: nonblocking connect rework")
Signed-off-by: liuyacan <liuyacan@corp.netease.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 165e3e17fe ]
A null pointer reference issue can be triggered when the response of a
stream reconf request arrives after the timer is triggered, such as:
send Incoming SSN Reset Request --->
CPU0:
reconf timer is triggered,
go to the handler code before hold sk lock
<--- reply with Outgoing SSN Reset Request
CPU1:
process Outgoing SSN Reset Request,
and set asoc->strreset_chunk to NULL
CPU0:
continue the handler code, hold sk lock,
and try to hold asoc->strreset_chunk, crash!
In Ying Xu's testing, the call trace is:
[ ] BUG: kernel NULL pointer dereference, address: 0000000000000010
[ ] RIP: 0010:sctp_chunk_hold+0xe/0x40 [sctp]
[ ] Call Trace:
[ ] <IRQ>
[ ] sctp_sf_send_reconf+0x2c/0x100 [sctp]
[ ] sctp_do_sm+0xa4/0x220 [sctp]
[ ] sctp_generate_reconf_event+0xbd/0xe0 [sctp]
[ ] call_timer_fn+0x26/0x130
This patch is to fix it by returning from the timer handler if asoc
strreset_chunk is already set to NULL.
Fixes: 7b9438de0c ("sctp: add stream reconf timer")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
