Pull SCSI fixes from James Bottomley:
- a couple of serious fixes: use after free and blacklist for WRITE
SAME
- one error leg fix: write_pending failure
- one user experience problem: do not override max_sectors_kb
- one minor unused function removal
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvscsis: Fix write_pending failure path
scsi: libiscsi: Remove iscsi_destroy_session
scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
scsi: sd: Do not override max_sectors_kb sysfs setting
scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP
Pull i2c fixes from Wolfram Sang:
"I2C has three driver fixes for the newly introduced drivers and one ID
addition for the i801 driver"
* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: make structure stm32f7_setup static const
i2c: ensure termination of *_device_id tables
i2c: i801: Add support for Intel Cedar Fork
i2c: stm32f7: fix setup structure
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
Now acking of edge irqs happens the following way:
- omap_gpio_irq_handler
- "isr" = read irq status
- omap_clear_gpio_irqbank(bank, isr_saved & ~level_mask);
^ clear edge status, so irq can be accepted
- loop while "isr"
generic_handle_irq()
- handle_edge_irq()
- desc->irq_data.chip->irq_ack(&desc->irq_data);
- omap_gpio_ack_irq()
it might be that at this moment edge IRQ was triggered again and it will be
cleared and IRQ will be lost.
Use handle_simple_irq and clear edge interrupts early without disabling them in
omap_gpio_irq_handler to avoid loosing interrupts.
[1] https://marc.info/?l=linux-omap&m=149004465313534&w=2
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The choice containing the CC_OPTIMIZE_FOR_PERFORMANCE symbol
accidentally added a "CONFIG_" prefix when trying to make it the
default, selecting an undefined symbol as the default.
The mistake is harmless here: Since the default symbol is not visible,
the choice falls back on using the visible symbol as the default
instead, which is CC_OPTIMIZE_FOR_PERFORMANCE, as intended.
A patch that makes Kconfig print a warning in this case has been
submitted separately:
http://www.spinics.net/lists/linux-kbuild/msg15566.html
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 040fcc819a ("kbuild: improved modversioning
support for external modules"), symverfile has been replaced
with kernelsymfile and modulesymfile.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I thought commit 8e9b466799 ("kbuild: use $(abspath ...) instead of
$(shell cd ... && /bin/pwd)") was a safe conversion, but it changed
the behavior.
$(abspath ...) / $(realpath ...) does not expand shell special
characters, such as '~'.
Here is a simple Makefile example:
---------------->8----------------
$(info /bin/pwd: $(shell cd ~/; /bin/pwd))
$(info abspath: $(abspath ~/))
$(info realpath: $(realpath ~/))
all:
@:
---------------->8----------------
$ make
/bin/pwd: /home/masahiro
abspath: /home/masahiro/workspace/~
realpath:
This can be a real problem if 'make O=~/foo' is invoked from another
Makefile or primitive shell like dash.
This commit partially reverts 8e9b466799.
Fixes: 8e9b466799 ("kbuild: use $(abspath ...) instead of $(shell cd ... && /bin/pwd)")
Reported-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Julien Grall <julien.grall@arm.com>
The skcipher walk interface doesn't handle zero-length input
properly as the old blkcipher walk interface did. This is due
to the fact that the length check is done too late.
This patch moves the length check forward so that it does the
right thing.
Fixes: b286d8b1a6 ("crypto: skcipher - Add skcipher walk...")
Cc: <stable@vger.kernel.org>
Reported-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SCTP program may sleep under a spinlock, and the function call path is:
sctp_generate_t3_rtx_event (acquire the spinlock)
sctp_do_sm
sctp_side_effects
sctp_cmd_interpreter
sctp_make_init_ack
sctp_pack_cookie
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
For the same reason, the orinoco driver may sleep in interrupt handler,
and the function call path is:
orinoco_rx_isr_tasklet
orinoco_rx
orinoco_mic
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool and my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
All error handling paths 'goto err_drop_spawn' except this one.
In order to avoid some resources leak, we should do it as well here.
Fixes: f1c131b454 ("crypto: xts - Convert to skcipher")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
gcc warns that the length for the extra unaligned data in the hash
function may be used unaligned. In theory this could happen if
we pass a zero-length sg_list, or if sg_is_last() was never true:
In file included from drivers/crypto/stm32/stm32-hash.c:23:
drivers/crypto/stm32/stm32-hash.c: In function 'stm32_hash_one_request':
include/uapi/linux/kernel.h:12:49: error: 'ncp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
#define __KERNEL_DIV_ROUND_UP(n, d) (((n) + (d) - 1) / (d))
Neither of these can happen in practice, so the warning is harmless.
However while trying to suppress the warning, I noticed multiple
problems with that code:
- On big-endian kernels, we byte-swap the data like we do for
register accesses, however this is a data stream and almost
certainly needs to use a single writesl() instead of series
of writel() to give the correct hash.
- If the length is not a multiple of four bytes, we skip the
last word entirely, since we write the truncated length
using stm32_hash_set_nblw().
- If we change the code to round the length up rather than
down, the last bytes contain stale data, so it needs some
form of padding.
This tries to address all four problems, by correctly
initializing the length to zero, using endian-safe copy
functions, adding zero-padding and passing the padded length.
I have done no testing on this patch, so please review
carefully and if possible test with an unaligned length
and big-endian kernel builds.
Fixes: 8a1012d3f2 ("crypto: stm32 - Support for STM32 HASH module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull hwmon fix from Guenter Roeck:
"Fix up error path in xgene driver"
* tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (xgene) Fix up error handling path mixup in 'xgene_hwmon_probe()'
Pull clk fixes from Stephen Boyd:
- build fix to export the clk_bulk_prepare() symbol
- suspend fix for Samsung Exynos SoCs where we need to keep clks on
across suspend
- two critical clk markings for clks that shouldn't ever turn off on
Rockchip SoCs
- a fix for a copy-paste mistake on Rockchip rk3128 causing some clks
to touch the same bit and trample over one another
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
clk: Export clk_bulk_prepare()
clk: rockchip: add sclk_timer5 as critical clock on rk3128
clk: rockchip: fix up rk3128 pvtm and mipi_24m gate regs error
clk: rockchip: add pclk_pmu as critical clock on rk3128
Pull ARC udpates from Vineet Gupta:
- updates for various platforms
- boot log updates for upcoming HS48 family of cores (dual issue)
* tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-hsdk]: Add reset controller node to manage ethernet reset
ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHz
ARC: fix allnoconfig build warning
ARCv2: boot log: identify HS48 cores (dual issue)
ARC: boot log: decontaminate ARCv2 ISA_CONFIG register
arc: remove redundant UTS_MACHINE define in arch/arc/Makefile
ARC: [plat-eznps] Update platform maintainer as Noam left
ARC: [plat-hsdk] use actual clk driver to manage cpu clk
ARC: [*defconfig] Reenable soft lock-up detector
ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequency
ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequency
ARC: [plat-axs103] Add temporary quirk to reset ethernet IP
Pull xfs fixes from Darrick Wong:
- fix a race between overlapping copy on write aio
- fix cow fork swapping when we defragment reflinked files
* tag 'xfs-4.14-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: handle racy AIO in xfs_reflink_end_cow
xfs: always swap the cow forks when swapping extents
This pull request brings in a fix for default serial console setup on
RPi3, so it now comes up with no config.txt/cmdline.txt settings in
the firmware.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Contrary to other RPi devices, RPi3 uses uart0 to communicate with
the BCM43438 bluetooth controller. uart1 is then used for the console.
Today, the console configuration is inherited from the bcm283x dtsi
(bootargs) which is not the correct one for the RPi3. This leads to
routing issue and confuses the Bluetooth controller with unexpected
data.
This patch introduces chosen/stdout path to configure console to uart0
on bcm283x family and overwrite it to uart1 in the RPi3 dts.
Create serial0/1 aliases referring to uart0 and uart1 paths.
Remove unneeded earlyprintk.
Fixes: 4188ea2aeb ("ARM: bcm283x: Define UART pinmuxing on board level")
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Pull block fixes from Jens Axboe:
"A collection of fixes for this series. This contains:
- NVMe pull request from Christoph, one uuid attribute fix, and one
fix for the controller memory buffer address for remapped BARs.
- use-after-free fix for bsg, from Benjamin Block.
- bcache race/use-after-free fix for a list traversal, fixing a
regression in this merge window. From Coly Li.
- null_blk change configfs dependency change from a 'depends' to a
'select'. This is a change from this merge window as well. From me.
- nbd signal fix from Josef, fixing a regression introduced with the
status code changes.
- nbd MAINTAINERS mailing list entry update.
- blk-throttle stall fix from Joseph Qi.
- blk-mq-debugfs fix from Omar, fixing an issue where we don't
register the IO scheduler debugfs directory, if the driver is
loaded with it. Only shows up if you switch through the sysfs
interface"
* 'for-linus' of git://git.kernel.dk/linux-block:
bsg-lib: fix use-after-free under memory-pressure
nvme-pci: Use PCI bus address for data/queues in CMB
blk-mq-debugfs: fix device sched directory for default scheduler
null_blk: change configfs dependency to select
blk-throttle: fix possible io stall when upgrade to max
MAINTAINERS: update list for NBD
nbd: fix -ERESTARTSYS handling
nvme: fix visibility of "uuid" ns attribute
bcache: use llist_for_each_entry_safe() in __closure_wake_up()
Pull PCI fixes from Bjorn Helgaas:
"Fix legacy IDE probe issues exposed by recent PCI core IRQ mapping
changes (Bartlomiej Zolnierkiewicz, Lorenzo Pieralisi)"
* tag 'pci-v4.14-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ide: fix IRQ assignment for PCI bus order probing
ide: pci: free PCI BARs on initialization failure
ide: free hwif->portdev on hwif_init() failure
In places like fc_rport_recv_plogi_req and fcoe_ctlr_vn_add we always
take the lport disc_mutex lock before the rports mutex
(rp_mutex) lock. Gaurding list_del_rcu(&rdata->peers) with
disc.disc_mutex in fc_rport_work is correct but the rp_mutex lock
can and should to be dropped before taking that lock else results
in a deadlock.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling rmmod() on a FC driver will results in warnings like
WARNING: CPU: 60 PID: 14640 at fs/sysfs/group.c:237 device_del+0x54/0x240()
sysfs group ffffffff81eff140 not found for kobject '3:0:0:3'
The problem here is that during scsi_remove_target() we will iterate
over all devices, but fail to remove any of those as the call to
scsi_device_get() fails the check to module_is_live(). Hence the
devices will not be removed at this point, but all intermediate
structures like fc rport etc. will be. Later on during
scsi_forget_host() the devices are removed for real, but the device
parent is already removed and causes this warning.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Kyle Fortin <kyle.fortin@oracle.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull arm64 fixes from Catalin Marinas:
- Bring initialisation of user space undefined instruction handling
early (core_initcall) since late_initcall() happens after modprobe in
initramfs is invoked. Similar fix for fpsimd initialisation
- Increase the kernel stack when KASAN is enabled
- Bring the PCI ACS enabling earlier via the
iort_init_platform_devices()
- Fix misleading data abort address printing (decimal vs hex)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Ensure fpsimd support is ready before userspace is active
arm64: Ensure the instruction emulation is ready for userspace
arm64: Use larger stacks when KASAN is selected
ACPI/IORT: Fix PCI ACS enablement
arm64: fix misleading data abort decoding
Pull KVM fixes from Radim Krčmář:
- fix PPC XIVE interrupt delivery
- fix x86 RCU breakage from asynchronous page faults when built without
PREEMPT_COUNT
- fix x86 build with -frecord-gcc-switches
- fix x86 build without X86_LOCAL_APIC
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: add X86_LOCAL_APIC dependency
x86/kvm: Move kvm_fastop_exception to .fixup section
kvm/x86: Avoid async PF preempting the kernel incorrectly
KVM: PPC: Book3S: Fix server always zero from kvmppc_xive_get_xive()
Pull rdma fixes from Doug Ledford:
"This is a pretty small pull request. Only 6 patches in total. There
are no outstanding -rc patches on the mailing list after this pull
request, so only if some new issues are discovered in the remainder of
the rc cycles will you hear from me again.
Summary:
- a fix for iwpm netlink usage
- a fix for error unwinding in mlx5
- two fixes to vlan handling in qedr
- a couple small i40iw fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
i40iw: Fix port number for query QP
i40iw: Add missing memory barriers
RDMA/qedr: Parse vlan priority as sl
RDMA/qedr: Parse VLAN ID correctly and ignore the value of zero
IB/mlx5: Fix label order in error path handling
RDMA/iwpm: Properly mark end of NL messages
ppp_release() tries to ensure that netdevices are unregistered before
decrementing the unit refcount and running ppp_destroy_interface().
This is all fine as long as the the device is unregistered by
ppp_release(): the unregister_netdevice() call, followed by
rtnl_unlock(), guarantee that the unregistration process completes
before rtnl_unlock() returns.
However, the device may be unregistered by other means (like
ppp_nl_dellink()). If this happens right before ppp_release() calling
rtnl_lock(), then ppp_release() has to wait for the concurrent
unregistration code to release the lock.
But rtnl_unlock() releases the lock before completing the device
unregistration process. This allows ppp_release() to proceed and
eventually call ppp_destroy_interface() before the unregistration
process completes. Calling free_netdev() on this partially unregistered
device will BUG():
------------[ cut here ]------------
kernel BUG at net/core/dev.c:8141!
invalid opcode: 0000 [#1] SMP
CPU: 1 PID: 1557 Comm: pppd Not tainted 4.14.0-rc2+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
Call Trace:
ppp_destroy_interface+0xd8/0xe0 [ppp_generic]
ppp_disconnect_channel+0xda/0x110 [ppp_generic]
ppp_unregister_channel+0x5e/0x110 [ppp_generic]
pppox_unbind_sock+0x23/0x30 [pppox]
pppoe_connect+0x130/0x440 [pppoe]
SYSC_connect+0x98/0x110
? do_fcntl+0x2c0/0x5d0
SyS_connect+0xe/0x10
entry_SYSCALL_64_fastpath+0x1a/0xa5
RIP: free_netdev+0x107/0x110 RSP: ffffc28a40573d88
---[ end trace ed294ff0cc40eeff ]---
We could set the ->needs_free_netdev flag on PPP devices and move the
ppp_destroy_interface() logic in the ->priv_destructor() callback. But
that'd be quite intrusive as we'd first need to unlink from the other
channels and units that depend on the device (the ones that used the
PPPIOCCONNECT and PPPIOCATTACH ioctls).
Instead, we can just let the netdevice hold a reference on its
ppp_file. This reference is dropped in ->priv_destructor(), at the very
end of the unregistration process, so that neither ppp_release() nor
ppp_disconnect_channel() can call ppp_destroy_interface() in the interim.
Reported-by: Beniamino Galvani <bgalvani@redhat.com>
Fixes: 8cb775bc0a ("ppp: fix device unregistration upon netns deletion")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull btrfs fixes from David Sterba:
"Two more fixes for bugs introduced in 4.13.
The sector_t problem with 32bit architecture and !LBDAF config seems
serious but the number of affected deployments is hopefully low.
The clashing status bits could lead to a confusing in-memory state of
the whole-filesystem operations if used with the quota override sysfs
knob"
* 'for-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix overlap of fs_info::flags values
btrfs: avoid overflow when sector_t is 32 bit
Pull ceph fixes from Ilya Dryomov:
"Two fixups for CephFS snapshot-handling patches in -rc1"
* tag 'ceph-for-4.14-rc4' of git://github.com/ceph/ceph-client:
ceph: fix __choose_mds() for LSSNAP request
ceph: properly queue cap snap for newly created snap realm
DW ethernet controller on HSDK hangs sometimes after SW reset, so
add reset node to make possible to reset DW ethernet controller HW.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull overlayfs fixes from Miklos Szeredi:
"Fix a regression in 4.14 and one in 4.13. The latter is a case when
Docker is doing something it really shouldn't and gets away with it.
We now print a warning instead of erroring out.
There are also fixes to several error paths"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix regression caused by exclusive upper/work dir protection
ovl: fix missing unlock_rename() in ovl_do_copy_up()
ovl: fix dentry leak in ovl_indexdir_cleanup()
ovl: fix dput() of ERR_PTR in ovl_cleanup_index()
ovl: fix error value printed in ovl_lookup_index()
ovl: fix may_write_real() for overlayfs directories
Pull powerpc fixes from Michael Ellerman:
"Nine small fixes, really nothing that stands out.
A work-around for a spurious MCE on Power9. A CXL fault handling fix,
some fixes to the new XIVE code, and a fix to the new 32-bit
STRICT_KERNEL_RWX code.
Fixes for old code/stable: an fix to an incorrect TLB flush on boot
but not on any current machines, a compile error on 4xx and a fix to
memory hotplug when using radix (Power9).
Thanks to: Anton Blanchard, Cédric Le Goater, Christian Lamparter,
Christophe Leroy, Christophe Lombard, Guenter Roeck, Jeremy Kerr,
Michael Neuling, Nicholas Piggin"
* tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Increase memory block size to 1GB on radix
powerpc/mm: Call flush_tlb_kernel_range with interrupts enabled
powerpc/xive: Clear XIVE internal structures when a CPU is removed
powerpc/xive: Fix IPI reset
powerpc/4xx: Fix compile error with 64K pages on 40x, 44x
powerpc: Fix action argument for cpufeatures-based TLB flush
cxl: Fix memory page not handled
powerpc: Fix workaround for spurious MCE on POWER9
powerpc: Handle MCE on POWER9 with only DSISR bit 30 set
Pull drm fixes from Dave Airlie:
"Some i915 fixes from the last two weeks (as they were on a strange
base and I just waited for rc3), also a single sun4i hdmi fix"
* tag 'drm-fixes-for-v4.14-rc4' of git://people.freedesktop.org/~airlied/linux:
drm/i915/glk: Fix DMC/DC state idleness calculation
drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
drm/i915: Fix DDI PHY init if it was already on
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
drm/i915/bios: ignore HDMI on port A
drm/i915: remove redundant variable hw_check
drm/i915: always update ELD connector type after get modes
Pull watchddog clean-up and fixes from Thomas Gleixner:
"The watchdog (hard/softlockup detector) code is pretty much broken in
its current state. The patch series addresses this by removing all
duct tape and refactoring it into a workable state.
The reasons why I ask for inclusion that late in the cycle are:
1) The code causes lockdep splats vs. hotplug locking which get
reported over and over. Unfortunately there is no easy fix.
2) The risk of breakage is minimal because it's already broken
3) As 4.14 is a long term stable kernel, I prefer to have working
watchdog code in that and the lockdep issues resolved. I wouldn't
ask you to pull if 4.14 wouldn't be a LTS kernel or if the
solution would be easy to backport.
4) The series was around before the merge window opened, but then got
delayed due to the UP failure caused by the for_each_cpu()
surprise which we discussed recently.
Changes vs. V1:
- Addressed your review points
- Addressed the warning in the powerpc code which was discovered late
- Changed two function names which made sense up to a certain point
in the series. Now they match what they do in the end.
- Fixed a 'unused variable' warning, which got not detected by the
intel robot. I triggered it when trying all possible related config
combinations manually. Randconfig testing seems not random enough.
The changes have been tested by and reviewed by Don Zickus and tested
and acked by Micheal Ellerman for powerpc"
* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
watchdog/core: Put softlockup_threads_initialized under ifdef guard
watchdog/core: Rename some softlockup_* functions
powerpc/watchdog: Make use of watchdog_nmi_probe()
watchdog/core, powerpc: Lock cpus across reconfiguration
watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
watchdog/hardlockup/perf: Cure UP damage
watchdog/hardlockup: Clean up hotplug locking mess
watchdog/hardlockup/perf: Simplify deferred event destroy
watchdog/hardlockup/perf: Use new perf CPU enable mechanism
watchdog/hardlockup/perf: Implement CPU enable replacement
watchdog/hardlockup/perf: Implement init time detection of perf
watchdog/hardlockup/perf: Implement init time perf validation
watchdog/core: Get rid of the racy update loop
watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
watchdog/sysctl: Clean up sysctl variable name space
watchdog/sysctl: Get rid of the #ifdeffery
watchdog/core: Clean up header mess
watchdog/core: Further simplify sysctl handling
watchdog/core: Get rid of the thread teardown/setup dance
...
We register the pm/hotplug callbacks for FPSIMD as late_initcall,
which happens after the userspace is active (from initramfs via
populate_rootfs, a rootfs_initcall). Make sure we are ready even
before the userspace could potentially use it, by promoting to
a core_initcall.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We trap and emulate some instructions (e.g, mrs, deprecated instructions)
for the userspace. However the handlers for these are registered as
late_initcalls and the userspace could be up and running from the initramfs
by that time (with populate_rootfs, which is a rootfs_initcall()). This
could cause problems for the early applications ending up in failure
like :
[ 11.152061] modprobe[93]: undefined instruction: pc=0000ffff8ca48ff4
This patch promotes the specific calls to core_initcalls, which are
guaranteed to be completed before we hit userspace.
Cc: stable@vger.kernel.org
Cc: Dave Martin <dave.martin@arm.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: James Morse <james.morse@arm.com>
Reported-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
syzkaller reports an out of bound read in strlcpy(), triggered
by xt_copy_counters_from_user()
Fix this by using memcpy(), then forcing a zero byte at the last position
of the destination, as Florian did for the non COMPAT code.
Fixes: d7591f0c41 ("netfilter: x_tables: introduce and use xt_copy_counters_from_user")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Prior to commit 55b9b50811 ("perf script: Support -F brstack,dso and
brstacksym,dso"), we were printing a space before the brstack data. It
seems that this space was important. Without it, parsing is difficult.
Very sorry for the mistake.
Notice here how the "ip" and "brstack" run together:
$ perf script -F ip,brstack | head -n 1
22e18c40x22e19e2/0x22e190b/P/-/-/0 0x22e19a1/0x22e19d0/P/-/-/0 0x22e195d/0x22e1990/P/-/-/0 0x22e18e9/0x22e1943/P/-/-/0 0x22e1a69/0x22e18c0/P/-/-/0 0x22e19f7/0x22e1a20/P/-/-/0 0x22e1910/0x22e19ee/P/-/-/0 0x22e19e2/0x22e190b/P/-/-/0 0x22e19a1/0x22e19d0/P/-/-/0 0x22e195d/0x22e1990/P/-/-/0 0x22e18e9/0x22e1943/P/-/-/0 0x22e1a69/0x22e18c0/P/-/-/0 0x22e19f7/0x22e1a20/P/-/-/0 0x22e1910/0x22e19ee/P/-/-/0 0x22e19e2/0x22e190b/P/-/-/0 0x22e19a1/0x22e19d0/P/-/-/0
After this diff, sanity is restored:
$ perf script -F ip,brstack | head -n 1
22e18c4 0x22e19e2/0x22e190b/P/-/-/0 0x22e19a1/0x22e19d0/P/-/-/0 0x22e195d/0x22e1990/P/-/-/0 0x22e18e9/0x22e1943/P/-/-/0 0x22e1a69/0x22e18c0/P/-/-/0 0x22e19f7/0x22e1a20/P/-/-/0 0x22e1910/0x22e19ee/P/-/-/0 0x22e19e2/0x22e190b/P/-/-/0 0x22e19a1/0x22e19d0/P/-/-/0 0x22e195d/0x22e1990/P/-/-/0 0x22e18e9/0x22e1943/P/-/-/0 0x22e1a69/0x22e18c0/P/-/-/0 0x22e19f7/0x22e1a20/P/-/-/0 0x22e1910/0x22e19ee/P/-/-/0 0x22e19e2/0x22e190b/P/-/-/0 0x22e19a1/0x22e19d0/P/-/-/0
Signed-off-by: Mark Santaniello <marksan@fb.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: 4.13+ <stable@vger.kernel.org>
Fixes: 55b9b50811 ("perf script: Support -F brstack,dso and brstacksym,dso")
Link: http://lkml.kernel.org/r/20171006080722.3442046-1-marksan@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently it's possible that on returning from the signal handler
through the restore_tm_sigcontexts() code path (e.g. from a signal
caught due to a `trap` instruction executed in the middle of an HTM
block, or a deliberately constructed sigframe) an illegal TM state
(like TS=10 TM=0, i.e. "T0") is set in SRR1 and when `rfid` sets
implicitly the MSR register from SRR1 register on return to userspace
it causes a TM Bad Thing exception.
That illegal state can be set (a) by a malicious user that disables
the TM bit by tweaking the bits in uc_mcontext before returning from
the signal handler or (b) by a sufficient number of context switches
occurring such that the load_tm counter overflows and TM is disabled
whilst in the signal handler.
This commit fixes the illegal TM state by ensuring that TM bit is
always enabled before we return from restore_tm_sigcontexts(). A small
comment correction is made as well.
Fixes: 5d176f751e ("powerpc: tm: Enable transactional memory (TM) lazily for userspace")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When using transactional memory (TM), the CPU can be in one of six
states as far as TM is concerned, encoded in the Machine State
Register (MSR). Certain state transitions are illegal and if attempted
trigger a "TM Bad Thing" type program check exception.
If we ever hit one of these exceptions it's treated as a bug, ie. we
oops, and kill the process and/or panic, depending on configuration.
One case where we can trigger a TM Bad Thing, is when returning to
userspace after a system call or interrupt, using RFID. When this
happens the CPU first restores the user register state, in particular
r1 (the stack pointer) and then attempts to update the MSR. However
the MSR update is not allowed and so we take the program check with
the user register state, but the kernel MSR.
This tricks the exception entry code into thinking we have a bad
kernel stack pointer, because the MSR says we're coming from the
kernel, but r1 is pointing to userspace.
To avoid this we instead always switch to the emergency stack if we
take a TM Bad Thing from the kernel. That way none of the user
register values are used, other than for printing in the oops message.
This is the fix for CVE-2017-1000255.
Fixes: 5d176f751e ("powerpc: tm: Enable transactional memory (TM) lazily for userspace")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Rewrite change log & comments, tweak asm slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The driver currently handles two NVM formats,
one for 7000 family and below, and one for 8000 family and above.
The 3168 series uses something in between,
so currently the driver uses incorrect offsets for it.
Fix the incorrect offsets.
Fixes: c4836b056d ("iwlwifi: Add PCI IDs for the new 3168 series")
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current channel flags printing is very strange and messy,
in LAR we sometimes print the channel number and sometimes the
frequency, in both we print a calculated value (whether ad-hoc
is supported or not) etc.
Unify all this to
* print the channel number, not the frequency
* remove the band print (2.4/5.2 GHz, it's obvious)
* remove the calculated Ad-Hoc print
Doing all of this also gets the length of the string to a max
of 101 characters, which is below the max of 110 for tracing,
and thus avoids the warning that came up on certain channels
with certain flag combinations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It seems that libsensors treats -EIO as a special non-recoverable
failure when it tries to read the temperature while the firmware is
not running. To solve that, change the error code to a milder
-ENODATA.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196941
Fixes: c221daf219 ("iwlwifi: mvm: add registration to thermal zone")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Today we stop the device and the DMA without stopping the dbgc
recording before. This causes host crashes when the DMA
rate is high.
Stop dbgc recording when clearing the fw debug configuration
to fix this.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In monitor mode we are not expected to decrypt encrypted
packets (not having the keys).
Hence we are expected to get an unknown rx security status.
Keeping the print in monitor mode causes a print for each
captured packet flooding the dmesg.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Memory hot unplug on PowerNV radix hosts is broken. Our memory block
size is 256MB but since we map the linear region with very large
pages, each pte we tear down maps 1GB.
A hot unplug of one 256MB memory block results in 768MB of memory
getting unintentionally unmapped. At this point we are likely to oops.
Fix this by increasing our memory block size to 1GB on PowerNV radix
hosts.
Fixes: 4b5d62ca17 ("powerpc/mm: add radix__remove_section_mapping()")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The > should be >= so that we don't write one element beyond the end of
the array.
Fixes: 16e7812241 ("selftests/net: Add a test to validate behavior of rx timestamps")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One bugfix in sun4i for 4.14
* tag 'drm-misc-fixes-2017-10-05' of git://anongit.freedesktop.org/git/drm-misc:
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
drm/i915 fixes for 4.14-rc4:
All 3 highest GLK bugs fixed by Imre:
- GLK drv reload - Fix DDI Phy init if it was already on.
- GLK suspend resume - Reprogram DMC firmware after s3/s4.
- GLK DC states - Fix idleness calculation.
* tag 'drm-intel-fixes-2017-10-04' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915/glk: Fix DMC/DC state idleness calculation
drm/i915/cnl: Reprogram DMC firmware after S3/S4 resume
drm/i915: Fix DDI PHY init if it was already on
Pull power management fix from Rafael Wysocki:
"This fixes a code ordering issue in the main suspend-to-idle loop that
causes some "low power S0 idle" conditions to be incorrectly reported
as unmet with suspend/resume debug messages enabled"
* tag 'pm-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / s2idle: Invoke the ->wake() platform callback earlier
