Fixes bug where variable i was redundantly used for counting two nested loops.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
`keypad_pads' is referred to by `keypad_data' which is
not __initdata, so `keypad_pads' should not be __initdata either.
Signed-off-by: Bjarne Steinsbo <bsteinsbo@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Simon Kirby reported that on his RAID setup with idedisk underneath
the box OOMs after a couple of days of runtime. Running with
CONFIG_DEBUG_KMEMLEAK pointed to idedisk_prep_fn() which unconditionally
allocates an ide_cmd struct. However, ide_requeue_and_plug() can be
called more than once per request, either from the request issue or the
IRQ handler path and do blk_peek_request() ends up in idedisk_prep_fn()
repeatedly, allocating a struct ide_cmd everytime and "forgetting" the
previous pointer.
Make sure the code reuses the old allocated chunk.
Reported-and-tested-by: Simon Kirby <sim@hostway.ca>
Cc: <stable@kernel.org> [ 39.x, 3.0.x ]
Link: http://marc.info/?l=linux-kernel&m=131667641517919
Link: http://lkml.kernel.org/r/20110922072643.GA27232@hostway.ca
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pch_gbe driver has an issue which a network stops,
when receiving traffic is high.
In the case, The link down and up are necessary to return a network.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link was downed during network use,
there is an issue on which PC freezes.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a minor change.
Up until kernel 2.6.32, getsockopt(fd, SOL_PACKET, PACKET_STATISTICS,
...) would return total and dropped packets since its last invocation. The
introduction of socket queue overflow reporting [1] changed drop
rate calculation in the normal packet socket path, but not when using a
packet ring. As a result, the getsockopt now returns different statistics
depending on the reception method used. With a ring, it still returns the
count since the last call, as counts are incremented in tpacket_rcv and
reset in getsockopt. Without a ring, it returns 0 if no drops occurred
since the last getsockopt and the total drops over the lifespan of
the socket otherwise. The culprit is this line in packet_rcv, executed
on a drop:
drop_n_acct:
po->stats.tp_drops = atomic_inc_return(&sk->sk_drops);
As it shows, the new drop number it taken from the socket drop counter,
which is not reset at getsockopt. I put together a small example
that demonstrates the issue [2]. It runs for 10 seconds and overflows
the queue/ring on every odd second. The reported drop rates are:
ring: 16, 0, 16, 0, 16, ...
non-ring: 0, 15, 0, 30, 0, 46, 0, 60, 0 , 74.
Note how the even ring counts monotonically increase. Because the
getsockopt adds tp_drops to tp_packets, total counts are similarly
reported cumulatively. Long story short, reinstating the original code, as
the below patch does, fixes the issue at the cost of additional per-packet
cycles. Another solution that does not introduce per-packet overhead
is be to keep the current data path, record the value of sk_drops at
getsockopt() at call N in a new field in struct packetsock and subtract
that when reporting at call N+1. I'll be happy to code that, instead,
it's just more messy.
[1] http://patchwork.ozlabs.org/patch/35665/
[2] http://kernel.googlecode.com/files/test-packetsock-getstatistics.c
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VM is saved and restored (or migrated) the netback driver will no
longer process any Tx packets from the frontend. xenvif_up() does not
schedule the processing of any pending Tx requests from the front end
because the carrier is off. Without this initial kick the frontend
just adds Tx requests to the ring without raising an event (until the
ring is full).
This was caused by 47103041e9 (net:
xen-netback: convert to hw_features) which reordered the calls to
xenvif_up() and netif_carrier_on() in xenvif_connect().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
removing obsoleted sysctl,
ip_rt_gc_interval variable no longer used since 2.6.38
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly PHY access and a few (ugly) debug statements for DMA control.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware is cached during the first successful call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().
It's similar to 953a12cc28 but the
firmware is mandatory.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This repairs problem with compile library in userspace (libnl).
Signed-off-by: Jiří Župka <jzupka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows ss command (iproute2) to display "ecnseen" if at least one packet
with ECT(0) or ECT(1) or ECN was received by this socket.
"ecn" means ECN was negotiated at session establishment (TCP level)
"ecnseen" means we received at least one packet with ECT fields set (IP
level)
ss -i
...
ESTAB 0 0 192.168.20.110:22 192.168.20.144:38016
ino:5950 sk:f178e400
mem:(r0,w0,f0,t0) ts sack ecn ecnseen bic wscale:7,8 rto:210
rtt:12.5/7.5 cwnd:10 send 9.3Mbps rcv_space:14480
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit removed some including headers:
"net: sh_eth: move the asm/sh_eth.h to include/linux/"
(commit id: d4fa0e35fd)
Then, the build failure happened on the linux-next:
drivers/net/ethernet/renesas/sh_eth.c:601: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/net/ethernet/renesas/sh_eth.c:1970: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/renesas/sh_eth.c:1970: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1971: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/renesas/sh_eth.c:1971: warning: function declaration isn't a prototype
drivers/net/ethernet/renesas/sh_eth.c:1972: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: data definition has no type or storage class
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/renesas/sh_eth.c:1972: warning: function declaration isn't a prototype
This patch fixes the issue. This patch also get back include/kernel.h
and linux/spinlock.h.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a test where a pair of bonding interfaces using ARP monitoring
were both brought up and torn down (with an rmmod) repeatedly, a panic
in the timer code was noticed. I tracked this down and determined that
any of the bonding functions that ran as workqueue handlers and requeued
more work might not properly exit when the module was removed.
There was a flag protected by the bond lock called kill_timers that is
set when the interface goes down or the module is removed, but many of
the functions that monitor link status now unlock the bond lock to take
rtnl first. There is a chance that another CPU running the rmmod could
get the lock and set kill_timers after the first check has passed.
This patch does not allow any function to queue work that will make
itself run unless kill_timers is not set. I also noticed while doing
this work that bond_resend_igmp_join_requests did not have a check for
kill_timers, so I added the needed call there as well.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Liang Zheng <lzheng@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocation of "phyinfo" wasn't checked, and also the allocation
wasn't freed on error paths. Sjur Brændeland pointed out as well
that "phy_driver" should be freed on the error path too.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to allow application to update existing fdb entries that already
exist. This makes bridge netlink neighbor API have same flags and
semantics as ip neighbor table.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is added to a bridge, the old code would send the new neighbor
netlink message before the subsequent new link message. This bug makes
it difficult to use the monitoring API in an application.
This code changes the ordering to add the forwarding entry
after the port is setup. One of the error checks (for invalid address)
is moved earlier in the process to avoid having to do unwind.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also changing it's frequency to once every 64s instead of existing 32s as
it was shown to affect performance
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was manifesting as a crash when FAT Dump extraction was attempted on a PPC machine.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was showing up as junk value on PPC /Big endian machines since
it was marked as a byte.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 60s delay before timeout on polling Bit 31 so that FAT dump can
complete when reset occurs.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai wrote:
> When a stream is paused, and its rule is expired while it is paused,
> no new rule will be configured to the HW when traffic resume.
[...]
> - When stream was resumed, traffic was steered again by RSS, and
> because current-cpu was equal to desired-cpu, ndo_rx_flow_steer
> wasn't called and no rule was configured to the HW.
Fix this by setting the flow's current CPU only in the table for the
newly selected RX queue.
Reported-and-tested-by: Amir Vadai <amirv@dev.mellanox.co.il>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When blanking an already blanked framebuffer, a kernel NULL pointer
dereference occurred, because mx3fb driver handles all kinds of screen
blanking (normal, vsync suspend, powerdown) in the same way.
Certain programs (Xorg X11 server) first do a normal blank, followed by
a powerdown blank, which triggered the bug.
Add an additional safeguard and make sdc_disable_channel() safe against
multiple calls independent of other logic.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Having "edid" as char caused a problem in ufx_read_edid() where we
compared "edid[i] != 0xFF". Because of the type difference, the
condition was never true and the error checking failed.
Also I added a __user notation to silence a sparse complaint.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The struct ore_striping_info will be used later in other
structures. And ore_calc_stripe_info as well. Rename them
make struct ore_striping_info public. ore_calc_stripe_info
is still static, will be made public on first use.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
The struct pnfs_osd_data_map data_map member of exofs_sb_info was
never used after mount. In fact all it's members were duplicated
by the ore_layout structure. So just remove the duplicated information.
Also removed some stupid, but perfectly supported, restrictions on
layout parameters. The case where num_devices is not divisible by
mirror_count+1 is perfectly fine since the rotating device view
will eventually use all the devices it can get.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
ore_components already has a comps member so this leads
to things like comps->comps which is annoying. the name oc
was already used in new code. So rename all old usage of
ore_components comps => ore_components oc.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
This quiets the following sparse noise:
warning: symbol 'exofs_sync_fs' was not declared. Should it be static?
warning: symbol 'exofs_free_sbi' was not declared. Should it be static?
warning: symbol 'exofs_get_parent' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
This quiets the sparse noise:
warning: symbol '_calc_trunk_info' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Any driver that selects SND_SOC_WM8994 should also make sure that
MFD_WM8994 is set, since the codec relies on the mfd code:
sound/built-in.o: In function `wm8994_read':
last.c:(.text+0x20160): undefined reference to `wm8994_reg_read'
sound/built-in.o: In function `wm8994_write':
last.c:(.text+0x20e68): undefined reference to `wm8994_reg_write'
This solves the problem by selecting the MFD driver directly
and adding extra 'depends on' statements to make sure that we
respect the dependencies of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.
Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.
Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
