Pull GPIO fixes from Linus Walleij:
- Fix a potential bit wrap issue in the Timberdale driver
- Fix up the buffer allocation size in the 74x164 driver
- Set the value in direction_output() right in the mvebu driver
- Return proper error codes for invalid GPIOs
- Fix an off-mode bug for the OMAP
- Don't initialize the mask_cach on the mvebu driver
* tag 'gpio-fixes-v3.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
GPIO: mvebu-gpio: Don't initialize the mask_cache
gpio/omap: fix off-mode bug: clear debounce settings on free/reset
gpiolib: Don't return -EPROBE_DEFER to sysfs, or for invalid gpios
gpio: mvebu: correctly set the value in direction_output()
gpio-74x164: Fix buffer allocation size
gpio-timberdale: fix a potential wrapping issue
Pull ext4 bugfix from Ted Ts'o:
"This fixes the root cause of the ext4 data corruption bug which raised
a ruckus on LWN, Phoronix, and Slashdot.
This bug only showed up when non-standard mount options
(journal_async_commit and/or journal_checksum) were enabled, and when
the file system was not cleanly unmounted, but the root cause was the
inode bitmap modifications was not being properly journaled.
This could potentially lead to minor file system corruptions (pass 5
complaints with the inode allocation bitmap) after an unclean shutdown
under the wrong/unlucky workloads, but it turned into major failure if
the journal_checksum and/or jouaral_async_commit was enabled."
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix unjournaled inode bitmap modification
Pull block driver update from Jens Axboe:
"Distilled down variant, the rest will pass over to 3.8. I pulled it
into the for-linus branch I had waiting for a pull request as well, in
case you are wondering why there are new entries in here too. This
also got rid of two reverts and the ones of the mtip32xx patches that
went in later in the 3.6 cycle, so the series looks a bit cleaner."
* 'for-linus' of git://git.kernel.dk/linux-block:
loop: Make explicit loop device destruction lazy
mtip32xx:Added appropriate timeout value for secure erase
xen/blkback: Change xen_vbd's flush_support and discard_secure to have type unsigned int, rather than bool
cciss: select CONFIG_CHECK_SIGNATURE
cciss: remove unneeded memset()
xen/blkback: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
pktcdvd: update MAINTAINERS
floppy: remove dr, reuse drive on do_floppy_init
floppy: use common function to check if floppies can be registered
floppy: properly handle failure on add_disk loop
floppy: do put_disk on current dr if blk_init_queue fails
floppy: don't call alloc_ordered_workqueue inside the alloc_disk loop
xen/blkback: Fix compile warning
block: Add blk_rq_pos(rq) to sort rq when plushing
drivers/block: remove CONFIG_EXPERIMENTAL
block: remove CONFIG_EXPERIMENTAL
vfs: fix: don't increase bio_slab_max if krealloc() fails
blkcg: stop iteration early if root_rl is the only request list
blkcg: Fix use-after-free of q->root_blkg and q->root_rl.blkg
Due to the SMP nature of some of the chips, which have per CPU
registers, the driver does not use the generic irq_gc_mask_set_bit() &
irq_gc_mask_clr_bit() functions, which only support a single register.
The driver has its own implementation of these functions, which can
pick the correct register depending on the CPU being used. The
functions do however use the gc->mask_cache value.
The call to irq_setup_generic_chip() was passing
IRQ_GC_INIT_MASK_CACHE, which caused the gc->mask_cache to be
initialized to the contents of some random register. This resulted in
unexpected interrupts been delivered from random GPIO lines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The reg property contains <base length> not <base last_offset>. Fix
the length values to be length not last_offset.
Cc: stable@vger.kernel.org
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Since there's no possible caller of dbgp_external_startup() and
dbgp_reset_prep() when !USB_EHCI_HCD, there's no point in building and
exporting these functions in that case. This eliminates a build error
under the conditions listed in the subject, introduced with the merge
f1c6872e49.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ath9k xmit functions for AMPDUs can send frames as non-aggregate in case
only one frame is currently available. The client will then answer using a
normal Ack instead of a BlockAck. This acknowledgement has no TID stored and
therefore the hardware is not able to provide us the corresponding TID.
The TID set by the hardware in the tx status descriptor has to be seen as
undefined and not as a valid TID value for normal acknowledgements. Doing
otherwise results in a massive amount of retransmissions and stalls of
connections.
Users may experience low bandwidth and complete connection stalls in
environments with transfers using multiple TIDs.
This regression was introduced in b11b160def
("ath9k: validate the TID in the tx status information").
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Cc: stable@vger.kernel.org
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware has correct (!= 0xff) value of tssi_bounds[4] in the
EEPROM, but step is equal to 0xff. This results on ridiculous delta
calculations and completely broke TX power settings.
Reported-and-tested-by: Pavel Lucik <pavel.lucik@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
usb: fixes for v3.7-rc4
We're reverting MUSB Mode 1 DMA patch which caused many regressions. Meanwhile
Roger is cooking a better version of that patch, which will hopefully be ready
for v3.8 merge window.
We also fix an undeclared error in ux5000_remove() and another build error
when we try to build USB_MUSB_OMAP2PLUS as a module.
Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED. If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.
So, treat an unexpected backend CLOSED state the same as CLOSING.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED. If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.
So, treat an unexpected backend CLOSED state the same as CLOSING.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
map->kmap_ops allocated in gntdev_alloc_map() wasn't freed by
gntdev_put_map().
Add a gntdev_free_map() helper function to free everything allocated
by gntdev_alloc_map().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
TWL4030_USB & TWL6030_USB must depend on USB_MUSB_OMAP2PLUS in Kconfig else
we get build errors with
CONFIG_USB_MUSB_HDRC=m
CONFIG_USB_MUSB_OMAP2PLUS=m
CONFIG_TWL4030_USB=y
CONFIG_TWL6030_USB=y
LD init/built-in.o
drivers/built-in.o: In function `twl4030_usb_irq':
drivers/usb/otg/twl4030-usb.c:518: undefined reference to `omap_musb_mailbox'
drivers/built-in.o: In function `twl4030_usb_phy_init':
drivers/usb/otg/twl4030-usb.c:540: undefined reference to `omap_musb_mailbox'
drivers/built-in.o: In function `twl6030_usb_irq':
drivers/usb/otg/twl6030-usb.c:230: undefined reference to `omap_musb_mailbox'
drivers/usb/otg/twl6030-usb.c:225: undefined reference to `omap_musb_mailbox'
drivers/built-in.o: In function `twl6030_usbotg_irq':
drivers/usb/otg/twl6030-usb.c:259: undefined reference to `omap_musb_mailbox'
CC: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Evalation of the WM5102 has identified a number of register values which
should be written after SYSCLK is enabled on revision A in order to
improve performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When disconnect callback is called, each component should wake up
sleepers and check card->shutdown flag for avoiding the endless sleep
blocking the proper resource release.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For more strict protection for wild disconnections, a refcount is
introduced to the card instance, and let it up/down when an object is
referred via snd_lookup_*() in the open ops.
The free-after-last-close check is also changed to check this refcount
instead of the empty list, too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace mutex with rwsem for codec->shutdown protection so that
concurrent accesses are allowed.
Also add the protection to snd_usb_autosuspend() and
snd_usb_autoresume(), too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Close some races at disconnection of a USB audio device by adding the
chip->shutdown_mutex and chip->shutdown check at appropriate places.
The spots to put bandaids are:
- PCM prepare, hw_params and hw_free
- where the usb device is accessed for communication or get speed, in
mixer.c and others; the device speed is now cached in subs->speed
instead of accessing to chip->dev
The accesses in PCM open and close don't need the mutex protection
because these are already handled in the core PCM disconnection code.
The autosuspend/autoresume codes are still uncovered by this patch
because of possible mutex deadlocks. They'll be covered by the
upcoming change to rwsem.
Also the mixer codes are untouched, too. These will be fixed in
another patch, too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix races at PCM disconnection:
- while a PCM device is being opened or closed
- while the PCM state is being changed without lock in prepare,
hw_params, hw_free ops
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
xfstests has always had random failures of tests due to loop devices
failing to be torn down and hence leaving filesytems that cannot be
unmounted. This causes test runs to immediately stop.
Over the past 6 or 7 years we've added hacks like explicit unmount
-d commands for loop mounts, losetup -d after unmount -d fails, etc,
but still the problems persist. Recently, the frequency of loop
related failures increased again to the point that xfstests 259 will
reliably fail with a stray loop device that was not torn down.
That is despite the fact the test is above as simple as it gets -
loop 5 or 6 times running mkfs.xfs with different paramters:
lofile=$(losetup -f)
losetup $lofile "$testfile"
"$MKFS_XFS_PROG" -b size=512 $lofile >/dev/null || echo "mkfs failed!"
sync
losetup -d $lofile
And losteup -d $lofile is failing with EBUSY on 1-3 of these loops
every time the test is run.
Turns out that blkid is running simultaneously with losetup -d, and
so it sees an elevated reference count and returns EBUSY. But why
is blkid running? It's obvious, isn't it? udev has decided to try
and find out what is on the block device as a result of a creation
notification. And it is racing with mkfs, so might still be scanning
the device when mkfs finishes and we try to tear it down.
So, make losetup -d force autoremove behaviour. That is, when the
last reference goes away, tear down the device. xfstests wants it
*gone*, not causing random teardown failures when we know that all
the operations the tests have specifically run on the device have
completed and are no longer referencing the loop device.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Added appropriate timeout value for secure erase based on identify device data
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Changing the type of bdev parameters to be unsigned int :1, rather than bool.
This is more consistent with the types of other features in the block drivers.
Signed-off-by: Oliver Chick <oliver.chick@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Peter is not going to maintain the driver any more. I have the
hardware.
Acked-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a small cleanup, that also may turn error handling of
unitialized disks more readable. We don't need a separate variable to
track allocated disks, remove dr and reuse drive variable instead.
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The same checks to see if a drive can be or is registered are
repeated through the code, factor out the checks in a common function
and replace the repeated checks with it.
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On floppy initialization, if something failed inside the loop we call
add_disk, there was no cleanup of previous iterations in the error
handling.
Cc: stable@vger.kernel.org
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since commit 070ad7e ("floppy: convert to delayed work and single-thread
wq"), we end up calling alloc_ordered_workqueue multiple times inside
the loop, which shouldn't be intended. Besides the leak, other side
effect in the current code is if blk_init_queue fails, we would end up
calling unregister_blkdev even if we didn't call yet register_blkdev.
Just moved the allocation of floppy_wq before the loop, and adjusted the
code accordingly.
Cc: stable@vger.kernel.org # 3.5+
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
drivers/block/xen-blkback/xenbus.c:260:5: warning: symbol 'xenvbd_sysfs_addif' was not declared. Should it be static?
drivers/block/xen-blkback/xenbus.c:284:6: warning: symbol 'xenvbd_sysfs_delif' was not declared. Should it be static?
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This adds a "select" dependency of KEYBOARD_LPC32XX on INPUT_MATRIXKMAP,
as the other drivers are doing in this regard. This fixes the following
compile error if KEYBOARD_LPC32XX is enabled but INPUT_MATRIXKMAP is not:
drivers/input/keyboard/lpc32xx-keys.c:230: undefined reference to
`matrix_keypad_build_keymap'
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When waking up from off-mode, some IP blocks are reset automatically by
hardware. For this reason, software must wait until the reset has
completed before attempting to access the IP block.
This patch fixes for example the bug introduced by commit
6c31b2150f ("mmc: omap_hsmmc: remove access
to SYSCONFIG register"), in which the MMC IP block is reset during
off-mode entry, but the code expects the module to be already available
during the execution of context restore.
This version includes a fix from Kevin Hilman <khilman@ti.com> for
GPIO problems on the 37xx EVM - thanks Kevin.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved softreset wait code into separate function; call
from top of _enable_sysc() rather than the bottom; include fix from Kevin
Hilman for GPIO sluggishness]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since CAM domain (ISS) has no module wake-up dependency
with any other clock domain of the device and the dynamic
dependency from L3_main_2 is always disabled, the domain
needs to be in force wakeup in order to be able to access
it for configure (sysconfig) it or use it.
Also since there is no clock in the domain managed automatically
by the hardware, there is no use to configure automatic
clock domain transition. SW should keep the SW_WKUP domain
transition as long as a module in the domain is required to
be functional.
Signed-off-by: Miguel Vadillo <vadillo@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
bf->bf_next is only while buffers are chained as part of an A-MPDU
in the tx queue. When a tid queue is flushed (e.g. on tearing down
an aggregation session), frames can be enqueued again as normal
transmission, without bf_next being cleared. This can lead to the
old pointer being dereferenced again later.
This patch might fix crashes and "Failed to stop TX DMA!" messages.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull Ceph fixes form Sage Weil:
"There are two fixes in the messenger code, one that can trigger a NULL
dereference, and one that error in refcounting (extra put). There is
also a trivial fix that in the fs client code that is triggered by NFS
reexport."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix dentry reference leak in encode_fh()
libceph: avoid NULL kref_put when osd reset races with alloc_msg
rbd: reset BACKOFF if unable to re-queue
Using the 'o' memory constraint in inline assembly can result in GCC
generating invalid immediate offsets for memory access instructions with
reduced addressing capabilities (i.e. smaller than 12-bit immediate
offsets):
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=54983
As there is no constraint to specify the exact addressing mode we need,
fallback to using 'Q' exclusively for halfword I/O accesses. This may
emit an additional add instruction (using an extra register) in order
to construct the address but it will always be accepted by GAS.
Reported-by: Bastian Hecht <hechtb@googlemail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After commit 846a136881 ("ARM: vfp: fix
saving d16-d31 vfp registers on v6+ kernels"), the OMAP 2430SDP board
started crashing during boot with omap2plus_defconfig:
[ 3.875122] mmcblk0: mmc0:e624 SD04G 3.69 GiB
[ 3.915954] mmcblk0: p1
[ 4.086639] Internal error: Oops - undefined instruction: 0 [#1] SMP ARM
[ 4.093719] Modules linked in:
[ 4.096954] CPU: 0 Not tainted (3.6.0-02232-g759e00b #570)
[ 4.103149] PC is at vfp_reload_hw+0x1c/0x44
[ 4.107666] LR is at __und_usr_fault_32+0x0/0x8
It turns out that the context save/restore fix unmasked a latent bug
in commit 5aaf254409 ("ARM: 6203/1: Make
VFPv3 usable on ARMv6"). When CONFIG_VFPv3 is set, but the kernel is
booted on a pre-VFPv3 core, the code attempts to save and restore the
d16-d31 VFP registers. These are only present on non-D16 VFPv3+, so
this results in an undefined instruction exception. The code didn't
crash before commit 846a136 because the save and restore code was
only touching d0-d15, present on all VFP.
Fix by implementing a request from Russell King to add a new HWCAP
flag that affirmatively indicates the presence of the d16-d31
registers:
http://marc.info/?l=linux-arm-kernel&m=135013547905283&w=2
and some feedback from Måns to clarify the name of the HWCAP flag.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@linaro.org>
Cc: Måns Rullgård <mans.rullgard@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
