usb@2184000: 'pinctrl-0' is a dependency of 'pinctrl-names'
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fixes: c100ea86e6 ("ARM: dts: add Netronix E60K02 board common file")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usb@2184000: 'pinctrl-0' is a dependency of 'pinctrl-names'
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fixes: 3bb3fd8565 ("ARM: dts: add Netronix E70K02 board common file")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'macirq' is supposed to be listed first. Also only 'snps,clk-csr' is
listed in the bindings while 'clk_csr' is only supported for legacy
reasons. See commit 83936ea8d8 ("net: stmmac: add a parse for new
property 'snps,clk-csr'")
Fixes: 1f4263ea6a ("arm64: dts: imx93: add eqos support")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'axi' clock are the bus APB clock, the 'disp_axi' clock are the
pixel data AXI clock. The naming is confusing. Fix the clock order.
Fixes: 94e6197dad ("arm64: dts: imx8mp: Add LCDIF2 & LDB nodes")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The WM8960 Linux driver expects the clock to be named "mclk". Otherwise
the clock will be ignored and not prepared/enabled by the driver.
Fixes: 40ba2eda0a ("arm64: dts: imx8mm-nitrogen-r2: add audio")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The deprecated property is named snps,reset-gpio, but this devicetree
used snps,reset-gpios instead which results in the reset not being used
and the following make dtbs_check error:
./arch/arm64/boot/dts/freescale/imx8dxl-evk.dtb: ethernet@5b050000: 'snps,reset-gpio' is a dependency of 'snps,reset-delays-us'
From schema: ./Documentation/devicetree/bindings/net/snps,dwmac.yaml
Use the preferred method of defining the reset gpio in the phy node
itself. Note that this drops the 10 us pre-delay, but prior this wasn't
used at all and a pre-delay doesn't make much sense in this context so
it should be fine.
Fixes: 8dd495d123 ("arm64: dts: freescale: add support for i.MX8DXL EVK board")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A recent commit eliminated a hack that adjusted the offset used for
many GSI registers. It became possible because we now specify all
GSI register offsets explicitly for every version of IPA.
Unfortunately, a large number of register offsets were *not* updated
as they should have been in that commit. For IPA v4.5+, the offset
for every GSI register *except* the two inter-EE interrupt masking
registers were supposed to have been reduced by 0xd000.
Tested-by: Luca Weiss <luca.weiss@fairphone.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Fixes: 59b12b1d27 ("net: ipa: kill gsi->virt_raw")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20230310193709.1477102-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As my testing on the MCM MT7530 switch on MT7621 SoC shows, setting the PLL
frequency does not affect MII modes other than trgmii on port 5 and port 6.
So the assumption is that the operation here called "setting the PLL
frequency" actually sets the frequency of the TRGMII TX clock.
Make it so that it and the rest of the trgmii setup run only when the
trgmii mode is used.
Tested rgmii and trgmii modes of port 6 on MCM MT7530 on MT7621AT Unielec
U7621-06 and standalone MT7530 on MT7623NI Bananapi BPI-R2.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230310073338.5836-2-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously we would divide total_left_rate by zero if num_vports
happened to be 1 because non_requested_count is calculated as
num_vports - req_count. Guard against this by validating num_vports at
the beginning and returning an error otherwise.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Fixes: bcd197c81f ("qed: Add vport WFQ configuration APIs")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309201556.191392-1-d-tatianin@yandex-team.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing a stress test on SMC-R by rmmod mlx5_ib driver
during the wrk/nginx test, we found that there is a probability
of triggering a panic while terminating all link groups.
This issue dues to the race between smc_smcr_terminate_all()
and smc_buf_create().
smc_smcr_terminate_all
smc_buf_create
/* init */
conn->sndbuf_desc = NULL;
...
__smc_lgr_terminate
smc_conn_kill
smc_close_abort
smc_cdc_get_slot_and_msg_send
__softirqentry_text_start
smc_wr_tx_process_cqe
smc_cdc_tx_handler
READ(conn->sndbuf_desc->len);
/* panic dues to NULL sndbuf_desc */
conn->sndbuf_desc = xxx;
This patch tries to fix the issue by always to check the sndbuf_desc
before send any cdc msg, to make sure that no null pointer is
seen during cqe processing.
Fixes: 0b29ec6436 ("net/smc: immediate termination for SMCR link groups")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://lore.kernel.org/r/1678263432-17329-1-git-send-email-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using a PHC in shared between multiple hosts, the previous
frequency value may not be reset and could lead to host being unable to
compensate the offset with timecounter adjustments. To avoid such state
reset the hardware frequency of PHC to zero on init. Some refactoring is
needed to make code readable.
Fixes: 85036aee19 ("bnxt_en: Add a non-real time mode to access NIC clock")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230310151356.678059-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 732ea9db9d ("efi: libstub: Move screen_info handling to common
code") reorganized the earlycon handling so that all architectures pass
the screen_info data via a EFI config table instead of populating struct
screen_info directly, as the latter is only possible when the EFI stub
is baked into the kernel (and not into the decompressor).
However, this means that struct screen_info may not have been populated
yet by the time the earlycon probe takes place, and this results in a
non-functional early console.
So let's probe again right after parsing the config tables and
populating struct screen_info. Note that this means that earlycon output
starts a bit later than before, and so it may fail to capture issues
that occur while doing the early EFI initialization.
Fixes: 732ea9db9d ("efi: libstub: Move screen_info handling to common code")
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Merge commit bf9bec4cb3 ("Merge branch 'bpf: Allow reads from uninit stack'")
from bpf-next to bpf tree to address verification issues in some programs
due to stack usage.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
slot_store() uses kstrtouint() to get a slot number, but stores the
result in an "int" variable (by casting a pointer).
This can result in a negative slot number if the unsigned int value is
very large.
A negative number means that the slot is empty, but setting a negative
slot number this way will not remove the device from the array. I don't
think this is a serious problem, but it could cause confusion and it is
best to fix it.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Song Liu <song@kernel.org>
The current interconnect provider registration interface is inherently
racy as nodes are not added until the after adding the provider. This
can specifically cause racing DT lookups to trigger a NULL-pointer
deference when either a NULL pointer or not fully initialised node is
returned from exynos_generic_icc_xlate().
Switch to using the new API where the provider is not registered until
after it has been fully initialised.
Fixes: 2f95b9d5cf ("interconnect: Add generic interconnect driver for Exynos SoCs")
Cc: stable@vger.kernel.org # 5.11
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230306075651.2449-16-johan+linaro@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Prior to commit 5ee5465940 ("kconfig: change sym_change_count to a
boolean flag"), the conf_updated flag was set to the new value *before*
calling the callback. xconfig's save action depends on this behaviour,
because xconfig calls conf_get_changed() directly from the callback and
now sees the old value, thus never enabling the save button or the
shortcut.
Restore the previous behaviour.
Fixes: 5ee5465940 ("kconfig: change sym_change_count to a boolean flag")
Signed-off-by: Jurica Vukadin <jura@vukad.in>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Presently, when a guest writes 1 to PMCR_EL0.{C,P}, which is WO/RAZ,
KVM saves the register value, including these bits.
When userspace reads the register using KVM_GET_ONE_REG, KVM returns
the saved register value as it is (the saved value might have these
bits set). This could result in userspace setting these bits on the
destination during migration. Consequently, KVM may end up resetting
the vPMU counter registers (PMCCNTR_EL0 and/or PMEVCNTR<n>_EL0) to
zero on the first KVM_RUN after migration.
Fix this by not saving those bits when a guest writes 1 to those bits.
Fixes: ab9468340d ("arm64: KVM: Add access handler for PMCR register")
Cc: stable@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20230313033234.1475987-1-reijiw@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Have KVM_GET_ONE_REG for vPMU counter (vPMC) registers (PMCCNTR_EL0
and PMEVCNTR<n>_EL0) return the sum of the register value in the sysreg
file and the current perf event counter value.
Values of vPMC registers are saved in sysreg files on certain occasions.
These saved values don't represent the current values of the vPMC
registers if the perf events for the vPMCs count events after the save.
The current values of those registers are the sum of the sysreg file
value and the current perf event counter value. But, when userspace
reads those registers (using KVM_GET_ONE_REG), KVM returns the sysreg
file value to userspace (not the sum value).
Fix this to return the sum value for KVM_GET_ONE_REG.
Fixes: 051ff581ce ("arm64: KVM: Add access handler for event counter register")
Cc: stable@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20230313033208.1475499-1-reijiw@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
If md_run() fails after ->active_io is initialized, then percpu_ref_exit
is called in error path. However, later md_free_disk will call
percpu_ref_exit again which leads to a panic because of null pointer
dereference. It can also trigger this bug when resources are initialized
but are freed in error path, then will be freed again in md_free_disk.
BUG: kernel NULL pointer dereference, address: 0000000000000038
Oops: 0000 [#1] PREEMPT SMP
Workqueue: md_misc mddev_delayed_delete
RIP: 0010:free_percpu+0x110/0x630
Call Trace:
<TASK>
__percpu_ref_exit+0x44/0x70
percpu_ref_exit+0x16/0x90
md_free_disk+0x2f/0x80
disk_release+0x101/0x180
device_release+0x84/0x110
kobject_put+0x12a/0x380
kobject_put+0x160/0x380
mddev_delayed_delete+0x19/0x30
process_one_work+0x269/0x680
worker_thread+0x266/0x640
kthread+0x151/0x1b0
ret_from_fork+0x1f/0x30
For creating raid device, md raid calls do_md_run->md_run, dm raid calls
md_run. We alloc those memory in md_run. For stopping raid device, md raid
calls do_md_stop->__md_stop, dm raid calls md_stop->__md_stop. So we can
free those memory resources in __md_stop.
Fixes: 72adae23a7 ("md: Change active_io to percpu")
Reported-and-tested-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Pull virtio fixes from Michael Tsirkin:
"Some virtio / vhost / vdpa fixes accumulated so far"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
tools/virtio: Ignore virtio-trace/trace-agent
vdpa_sim: set last_used_idx as last_avail_idx in vdpasim_queue_ready
vhost-vdpa: free iommu domain after last use during cleanup
vdpa/mlx5: should not activate virtq object when suspended
vp_vdpa: fix the crash in hot unplug with vp_vdpa
A potentially malicious SEV guest can constantly hammer the hypervisor
using this driver to send down requests and thus prevent or at least
considerably hinder other guests from issuing requests to the secure
processor which is a shared platform resource.
Therefore, the host is permitted and encouraged to throttle such guest
requests.
Add the capability to handle the case when the hypervisor throttles
excessive numbers of requests issued by the guest. Otherwise, the VM
platform communication key will be disabled, preventing the guest from
attesting itself.
Realistically speaking, a well-behaved guest should not even care about
throttling. During its lifetime, it would end up issuing a handful of
requests which the hardware can easily handle.
This is more to address the case of a malicious guest. Such guest should
get throttled and if its VMPCK gets disabled, then that's its own
wrongdoing and perhaps that guest even deserves it.
To the implementation: the hypervisor signals with SNP_GUEST_REQ_ERR_BUSY
that the guest requests should be throttled. That error code is returned
in the upper 32-bit half of exitinfo2 and this is part of the GHCB spec
v2.
So the guest is given a throttling period of 1 minute in which it
retries the request every 2 seconds. This is a good default but if it
turns out to not pan out in practice, it can be tweaked later.
For safety, since the encryption algorithm in GHCBv2 is AES_GCM, control
must remain in the kernel to complete the request with the current
sequence number. Returning without finishing the request allows the
guest to make another request but with different message contents. This
is IV reuse, and breaks cryptographic protections.
[ bp:
- Rewrite commit message and do a simplified version.
- The stable tags are supposed to denote that a cleanup should go
upfront before backporting this so that any future fixes to this
can preserve the sanity of the backporter(s). ]
Fixes: d5af44dde5 ("x86/sev: Provide support for SNP guest request NAEs")
Signed-off-by: Dionna Glaze <dionnaglaze@google.com>
Co-developed-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@kernel.org> # d6fd48eff7 ("virt/coco/sev-guest: Check SEV_SNP attribute at probe time")
Cc: <stable@kernel.org> # 970ab82374 (" virt/coco/sev-guest: Simplify extended guest request handling")
Cc: <stable@kernel.org> # c5a338274b ("virt/coco/sev-guest: Remove the disable_vmpck label in handle_guest_request()")
Cc: <stable@kernel.org> # 0fdb6cc7c8 ("virt/coco/sev-guest: Carve out the request issuing logic into a helper")
Cc: <stable@kernel.org> # d25bae7dc7 ("virt/coco/sev-guest: Do some code style cleanups")
Cc: <stable@kernel.org> # fa4ae42cc6 ("virt/coco/sev-guest: Convert the sw_exit_info_2 checking to a switch-case")
Link: https://lore.kernel.org/r/20230214164638.1189804-2-dionnaglaze@google.com
snp_issue_guest_request() checks the value returned by the hypervisor in
sw_exit_info_2 and returns a different error depending on it.
Convert those checks into a switch-case to make it more readable when
more error values are going to be checked in the future.
No functional changes.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20230307192449.24732-8-bp@alien8.de
Return a specific error code - -ENOSPC - to signal the too small cert
data buffer instead of checking exit code and exitinfo2.
While at it, hoist the *fw_err assignment in snp_issue_guest_request()
so that a proper error value is returned to the callers.
[ Tom: check override_err instead of err. ]
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230307192449.24732-4-bp@alien8.de
When tunneling aggregated USB3 (20 Gb/s) the bandwidth values that are
programmed to the ADP_USB3_CS_2 go higher than 4096 and that does not
fit anymore to the 12-bit field. Fix this by scaling the value using
the scale field accordingly.
Fixes: 3b1d8d577c ("thunderbolt: Implement USB3 bandwidth negotiation routines")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Current Intel USB4 host routers have hardware limitation that the USB3
bandwidth cannot go higher than 16376 Mb/s. Work this around by adding a
new quirk that limits the bandwidth for the affected host routers.
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to apply quirks based on certain adapter types move call to
tb_check_quirks() happen after the adapters are initialized. This should
not affect the existing quirks.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to USB4 retimer specification, the process of firmware update
sequence requires issuing a SET_INBOUND_SBTX port operation that later
shall be followed by UNSET_INBOUND_SBTX port operation. This last step
is not currently issued by the driver but it is necessary to make sure
the retimers are put back to passthrough mode even during enumeration.
If this step is missing the link may not come up properly after
soft-reboot for example.
For this reason issue UNSET_INBOUND_SBTX after SET_INBOUND_SBTX for
enumeration and also when the NVM upgrade is run.
Reported-by: Christian Schaubschläger <christian.schaubschlaeger@gmx.at>
Link: https://lore.kernel.org/linux-usb/b556f5ed-5ee8-9990-9910-afd60db93310@gmx.at/
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Memory for the usb4->margining needs to be relased for the upstream port
of the router as well, even though the debugfs directory gets released
with the router device removal. Fix this.
Fixes: d0f1e0c2a6 ("thunderbolt: Add support for receiver lane margining")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
