commit f5cb92ac82 upstream.
irq_move_masked_irq() checks the return code of
chip->irq_set_affinity() only for 0, but IRQ_SET_MASK_OK_NOCOPY is
also a valid return code, which is there to avoid a redundant copy of
the cpumask. But in case of IRQ_SET_MASK_OK_NOCOPY we not only avoid
the redundant copy, we also fail to adjust the thread affinity of an
eventually threaded interrupt handler.
Handle IRQ_SET_MASK_OK (==0) and IRQ_SET_MASK_OK_NOCOPY(==1) return
values correctly by checking the valid return values seperately.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Keping Chen <chenkeping@huawei.com>
Link: http://lkml.kernel.org/r/1333120296-13563-2-git-send-email-jiang.liu@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a09b659cd6 upstream.
In 2008, commit 0c5d1eb77a ("genirq: record trigger type") modified the
way set_irq_type() handles the 'no trigger' condition. However, this has
an adverse effect on PCMCIA support on Intel StrongARM and probably PXA
platforms.
PCMCIA has several status signals on the socket which can trigger
interrupts; some of these status signals depend on the card's mode
(whether it is configured in memory or IO mode). For example, cards have
a 'Ready/IRQ' signal: in memory mode, this provides an indication to
PCMCIA that the card has finished its power up initialization. In IO
mode, it provides the device interrupt signal. Other status signals
switch between on-board battery status and loud speaker output.
In classical PCMCIA implementations, where you have a specific socket
controller, the controller provides a method to mask interrupts from the
socket, and importantly ignore any state transitions on the pins which
correspond with interrupts once masked. This masking prevents unwanted
events caused by the removal and application of socket power being
forwarded.
However, on platforms where there is no socket controller, the PCMCIA
status and interrupt signals are routed to standard edge-triggered GPIOs.
These GPIOs can be configured to interrupt on rising edge, falling edge,
or never. This is where the problems start.
Edge triggered interrupts are required to record events while disabled via
the usual methods of {free,request,disable,enable}_irq() to prevent
problems with dropped interrupts (eg, the 8390 driver uses disable_irq()
to defer the delivery of interrupts). As a result, these interfaces can
not be used to implement the desired behaviour.
The side effect of this is that if the 'Ready/IRQ' GPIO is disabled via
disable_irq() on suspend, and enabled via enable_irq() after resume, we
will record the state transitions caused by powering events as valid
interrupts, and foward them to the card driver, which may attempt to
access a card which is not powered up.
This leads delays resume while drivers spin in their interrupt handlers,
and complaints from drivers before they realize what's happened.
Moreover, in the case of the 'Ready/IRQ' signal, this is requested and
freed by the card driver itself; the PCMCIA core has no idea whether the
interrupt is requested, and, therefore, whether a call to disable_irq()
would be valid. (We tried this around 2.4.17 / 2.5.1 kernel era, and
ended up throwing it out because of this problem.)
Therefore, it was decided back in around 2002 to disable the edge
triggering instead, resulting in all state transitions on the GPIO being
ignored. That's what we actually need the hardware to do.
The commit above changes this behaviour; it explicitly prevents the 'no
trigger' state being selected.
The reason that request_irq() does not accept the 'no trigger' state is
for compatibility with existing drivers which do not provide their desired
triggering configuration. The set_irq_type() function is 'new' and not
used by non-trigger aware drivers.
Therefore, revert this change, and restore previously working platforms
back to their former state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: linux@arm.linux.org.uk
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52abb700e1 upstream.
Xommit ac5637611(genirq: Unmask oneshot irqs when thread was not woken)
fails to unmask when a !IRQ_ONESHOT threaded handler is handled by
handle_level_irq.
This happens because thread_mask is or'ed unconditionally in
irq_wake_thread(), but for !IRQ_ONESHOT interrupts never cleared. So
the check for !desc->thread_active fails and keeps the interrupt
disabled.
Keep the thread_mask zero for !IRQ_ONESHOT interrupts.
Document the thread_mask magic while at it.
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Reported-and-tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4bc724e82 upstream.
An interrupt might be pending when irq_startup() is called, but the
startup code does not invoke the resend logic. In some cases this
prevents the device from issuing another interrupt which renders the
device non functional.
Call the resend function in irq_startup() to keep things going.
Reported-and-tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac56376111 upstream.
When the primary handler of an interrupt which is marked IRQ_ONESHOT
returns IRQ_HANDLED or IRQ_NONE, then the interrupt thread is not
woken and the unmask logic of the interrupt line is never
invoked. This keeps the interrupt masked forever.
This was not noticed as most IRQ_ONESHOT users wake the thread
unconditionally (usually because they cannot access the underlying
device from hard interrupt context). Though this behaviour was nowhere
documented and not necessarily intentional. Some drivers can avoid the
thread wakeup in certain cases and run into the situation where the
interrupt line s kept masked.
Handle it gracefully.
Reported-and-tested-by: Lothar Wassmann <lw@karo-electronics.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 550acb1926 upstream.
In irq_wait_for_interrupt(), the should_stop member is verified before
setting the task's state to TASK_INTERRUPTIBLE and calling schedule().
In case kthread_stop sets should_stop and wakes up the process after
should_stop is checked by the irq thread but before the task's state
is changed, the irq thread might never exit:
kthread_stop irq_wait_for_interrupt
------------ ----------------------
...
... while (!kthread_should_stop()) {
kthread->should_stop = 1;
wake_up_process(k);
wait_for_completion(&kthread->exited);
...
set_current_state(TASK_INTERRUPTIBLE);
...
schedule();
}
Fix this by checking if the thread should stop after modifying the
task's state.
[ tglx: Simplified it a bit ]
Signed-off-by: Ido Yariv <ido@wizery.com>
Link: http://lkml.kernel.org/r/1322740508-22640-1-git-send-email-ido@wizery.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 52553ddffa upstream.
Commit fa27271bc8d2("genirq: Fixup poll handling") introduced a
regression that broke irqfixup/irqpoll for some hardware configurations.
Amidst reorganizing 'try_one_irq', that patch removed a test that
checked for 'action->handler' returning IRQ_HANDLED, before acting on
the interrupt. Restoring this test back returns the functionality lost
since 2.6.39. In the current set of tests, after 'action' is set, it
must precede '!action->next' to take effect.
With this and my previous patch to irq/spurious.c, c75d720fca, all
IRQ regressions that I have encountered are fixed.
Signed-off-by: Edward Donovan <edward.donovan@numble.net>
Reported-and-tested-by: Rogério Brito <rbrito@ime.usp.br>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c75d720fca upstream.
commit d05c65fff0 ("genirq: spurious: Run only one poller at a time")
introduced a regression, leaving the boot options 'irqfixup' and
'irqpoll' non-functional. The patch placed tests in each function, to
exit if the function is already running. The test in 'misrouted_irq'
exited when it should have proceeded, effectively disabling
'misrouted_irq' and 'poll_spurious_irqs'.
The check for an already running poller needs to be "!= 1" not "== 1"
as "1" is the value when the first poller starts running.
Signed-off-by: Edward Donovan <edward.donovan@numble.net>
Cc: maciej.rutecki@gmail.com
Link: http://lkml.kernel.org/r/1320175784-6745-1-git-send-email-edward.donovan@numble.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ed585a6516 upstream.
If an irq_chip provides .irq_shutdown(), but neither of .irq_disable() or
.irq_mask(), free_irq() crashes when jumping to NULL.
Fix this by only trying .irq_disable() and .irq_mask() if there's no
.irq_shutdown() provided.
This revives the symmetry with irq_startup(), which tries .irq_startup(),
.irq_enable(), and irq_unmask(), and makes it consistent with the comment for
irq_chip.irq_shutdown() in <linux/irq.h>, which says:
* @irq_shutdown: shut down the interrupt (defaults to ->disable if NULL)
This is also how __free_irq() behaved before the big overhaul, cfr. e.g.
3b56f0585f ("genirq: Remove bogus conditional"),
where the core interrupt code always overrode .irq_shutdown() to
.irq_disable() if .irq_shutdown() was NULL.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Link: http://lkml.kernel.org/r/1315742394-16036-2-git-send-email-geert@linux-m68k.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In kernel/irq/manage.c::irq_set_irq_wake() we call
irq_get_desc_buslock() which may return NULL, but the code
dereferences the result unconditionally.
irq_set_irq_wake() has lots of callers - I checked a few and I couldn't
find anything that guarantees that they won't call it with some input that
will cause irq_get_desc_buslock() to return NULL, so I think it's a good
thing to test and -EINVAL was the most sane error code in this situation
that I could think of.
Not all callers test the return value of irq_set_irq_wake(), but those
that do take != 0 to mean error as far as I can see, so they should be
fine. I guess those that don't test actually should, but that's a
different issue.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1106092300360.17868@swampdragon.chaosbits.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When irq_alloc_descs() is called with no base IRQ specified then it will
search for a range of IRQs starting from a specified base address. In the
case where an IRQ is specified it still does this search in order to ensure
that none of the requested range is already allocated and it still uses the
from parameter to specify the base for the search. This means that in the
case where a base is specified but from is zero (which is reasonable as
any IRQ number is in the range specified by a zero from) the function will
get confused and try to allocate the first suitably sized block of free IRQs
it finds.
Instead use a specified IRQ as the base address for the search, and insist
that any from that is specified can support that IRQ.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Link: http://lkml.kernel.org/r/1307037313-15733-1-git-send-email-broonie@opensource.wolfsonmicro.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The genirq changes are initializing descriptors for sparse IRQs quite
differently from how non-sparse (stacked?) IRQs are initialized, with
the effect that on my platform all IRQs are default-disabled on sparse
IRQs and default-enabled if non-sparse IRQs are used, crashing some
GPIO driver.
Fix this by refactoring the non-sparse IRQs to use the same descriptor
init function as the sparse IRQs.
Signed-off: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/1306858479-16622-1-git-send-email-linus.walleij@stericsson.com
Cc: stable@kernel.org # 2.6.39
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The detection of spurios interrupts is currently limited to first level
handler. In force-threaded mode we never notice if the threaded irq does
not feel responsible.
This patch catches the return value of the threaded handler and forwards
it to the spurious detector. If the primary handler returns only
IRQ_WAKE_THREAD then the spourious detector ignores it because it gets
called again from the threaded handler.
[ tglx: Report the erroneous return value early and bail out ]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/1306824972-27067-2-git-send-email-sebastian@breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit 4b06042(bitmap, irq: add smp_affinity_list interface to
/proc/irq) causes the following warning:
[ 274.239500] WARNING: at fs/proc/generic.c:850 remove_proc_entry+0x24c/0x27a()
[ 274.251761] remove_proc_entry: removing non-empty directory 'irq/184',
leaking at least 'smp_affinity_list'
Remove the new file in the exit path.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Mike Travis <travis@sgi.com>
Link: http://lkml.kernel.org/r/4DDDE094.6050505@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Manually adjusting the smp_affinity for IRQ's becomes unwieldy when the
cpu count is large.
Setting smp affinity to cpus 256 to 263 would be:
echo 000000ff,00000000,00000000,00000000,00000000,00000000,00000000,00000000 > smp_affinity
instead of:
echo 256-263 > smp_affinity_list
Think about what it looks like for cpus around say, 4088 to 4095.
We already have many alternate "list" interfaces:
/sys/devices/system/cpu/cpuX/indexY/shared_cpu_list
/sys/devices/system/cpu/cpuX/topology/thread_siblings_list
/sys/devices/system/cpu/cpuX/topology/core_siblings_list
/sys/devices/system/node/nodeX/cpulist
/sys/devices/pci***/***/local_cpulist
Add a companion interface, smp_affinity_list to use cpu lists instead of
cpu maps. This conforms to other companion interfaces where both a map
and a list interface exists.
This required adding a bitmap_parselist_user() function in a manner
similar to the bitmap_parse_user() function.
[akpm@linux-foundation.org: make __bitmap_parselist() static]
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export handle_simple_irq, irq_modify_status, irq_alloc_descs,
irq_free_descs and generic_handle_irq to allow their usage in
modules. First user is IIO, which wants to be built modular, but needs
to be able to create irq chips, allocate and configure interrupt
descriptors and handle demultiplexing interrupts.
[ tglx: Moved the uninlinig of generic_handle_irq to a separate patch ]
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Link: http://lkml.kernel.org/r/%3C1305711544-505-1-git-send-email-jic23%40cam.ac.uk%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
generic_handle_irq() is missing a NULL pointer check for the result of
irq_to_desc. This was a not a big problem, but we want to expose it to
drivers, so we better have sanity checks in place. Add a return value
as well, which indicates that the irq number was valid and the handler
was invoked.
Based on the pure code move from Jonathan Cameron.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
kernel/irq/ is only built when CONFIG_GENERIC_HARDIRQS=y. So making
code inside of kernel/irq/ conditional on CONFIG_GENERIC_HARDIRQS is
pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These callbacks are only called in the syscore suspend/resume code on
interrupt chips which have been registered via the generic irq chip
mechanism. Calling those callbacks per irq would be rather icky, but
with the generic irq chip mechanism we can call this per registered
chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
This adds support for disabling threading on a per-IRQ basis via the IRQ
status instead of the IRQ flow, which is necessary for interrupts that
don't follow the natural IRQ flow channels, such as those that are
virtually created.
The new APIs added are simply:
irq_set_thread()
irq_set_nothread()
which follow the rest of the IRQ status routines.
Chained handlers also have IRQ_NOTHREAD set on them automatically, making
the lack of threading explicit rather than implicit. Subsequently, the
nothread flag can be viewed through the standard genirq debugging
facilities.
[ tglx: Fixed cleanup fallout ]
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/%3C20110406210135.GF18426%40linux-sh.org%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
The only subtle difference is that alpha uses ACTUAL_NR_IRQS and
prints the IRQF_DISABLED flag.
Change the generic implementation to deal with ACTUAL_NR_IRQS if
defined.
The IRQF_DISABLED printing is pointless, as we nowadays run all
interrupts with irqs disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The late night fixup missed to convert the data type from irq_desc to
irq_data, which results in a harmless but annoying warning.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I missed the CONFIG_GENERIC_PENDING_IRQ dependency in the affinity
related functions and the IRQ_LEVEL propagation into irq_data
state. Did not pop up on my main test platforms. :(
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: David Daney <ddaney@caviumnetworks.com>
Fix new irq-related kernel-doc warnings in 2.6.38:
Warning(kernel/irq/manage.c:149): No description found for parameter 'mask'
Warning(kernel/irq/manage.c:149): Excess function parameter 'cpumask' description in 'irq_set_affinity'
Warning(include/linux/irq.h:161): No description found for parameter 'state_use_accessors'
Warning(include/linux/irq.h:161): Excess struct/union/enum/typedef member 'state_use_accessor' description in 'irq_data'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <20110318093356.b939558d.randy.dunlap@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is a replacment for the cell flow handler which is in the way of
cleanups. Must be selected to avoid general bloat.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We really need these flags for some of the interrupt chips. Move it
from internal state to irq_data and provide proper accessors.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Daney <ddaney@caviumnetworks.com>
The .irq_cpu_online() and .irq_cpu_offline() functions may need to
adjust affinity, but they are called with the descriptor lock held.
Create __irq_set_affinity_locked() which is called with the lock held.
Make irq_set_affinity() just a wrapper that acquires the lock.
[ tglx: Changed the argument to irq_data, added a !desc check and
moved the !irq_set_affinity check where it belongs ]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: ralf@linux-mips.org
LKML-Reference: <1301081931-11240-4-git-send-email-ddaney@caviumnetworks.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a flag which indicates that the on/offline callback should only be
called on enabled interrupts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some irq_chip implementation require to know the disabled state of the
interrupt in certain callbacks. Add a state flag and accessor to
irq_data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some archs want to print extra information for certain irq_chips which
is per irq and not per chip. Allow them to provide a chip callback to
print the chip name and the extra information.
PowerPC wants to print the LEVEL/EDGE type information. Make it configurable.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
