IMX93 do not contain a GPR to config the stop mode, it will set
the flexcan into stop mode automatically once the ARM core go
into low power mode (WFI instruct) and gate off the flexcan
related clock automatically. But to let these logic work as
expect, before ARM core go into low power mode, need to make
sure the flexcan related clock keep on.
To support stop mode and wakeup feature on imx93, this patch
add a new fsl_imx93_devtype_data to separate from imx8mp.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/1669116752-4260-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: Ondrej Ille <ondrej.ille@gmail.com>
Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Link: https://lore.kernel.org/all/20221124141604.4265225f@endymion.delvare
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Biju Das <biju.das.jz@bp.renesas.com> says:
The CAN FD IP found on RZ/G2L SoC has some HW features different to
that of R-Car. For example, it has multiple resets, dedicated channel
tx and error interrupts, separate global rx and error interrupts
compared to shared irq for R-Car. it does not s ECC error flag
registers and clk post divider present on R-Car.
Similarly, R-Car V3U has 8 channels whereas other SoCs has only 2
channels. Currently all the HW differences are handled by comparing
with chip_id enum.
This patch series aims to replace chip_id with struct
rcar_canfd_hw_info to handle the HW feature differences and driver
data present on both IPs.
The changes are trivial and tested on RZ/G2L SMARC EVK.
This patch series depend upon [1].
[1] https://lore.kernel.org/all/20221025155657.1426948-1-biju.das.jz@bp.renesas.com
changes since v2: https://lore.kernel.org/all/20221026131732.1843105-1-biju.das.jz@bp.renesas.com
* Replaced data type of max_channels from unsigned int->u8 to save memory.
* Replaced data type of postdiv from unsigned int->u8 to save memory.
changes since v1: https://lore.kernel.org/all/20221022104357.1276740-1-biju.das.jz@bp.renesas.com
* Updated commit description for R-Car V3U SoC detection using
driver data.
* Replaced data type of max_channels from u32->unsigned int.
* Replaced multi_global_irqs->shared_global_irqs to make it
positive checks.
* Replaced clk_postdiv->postdiv driver data variable.
* Simplified the calcualtion for fcan_freq.
* Replaced info->has_gerfl to gpriv->info->has_gerfl and wrapped
the ECC error flag checks inside a single if statement.
* Added Rb tag from Geert patch#1,#2,#3 and #5
Link: https://lore.kernel.org/all/20221027082158.95895-1-biju.das.jz@bp.renesas.com
[mkl: only take patches 1...5 to avoid merge conflict]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Xin Long says:
====================
net: eliminate the duplicate code in the ct nat functions of ovs and tc
The changes in the patchset:
"net: add helper support in tc act_ct for ovs offloading"
had moved some common ct code used by both OVS and TC into netfilter.
There are still some big functions pretty similar defined and used in
each of OVS and TC. It is not good to maintain such big function in 2
places. This patchset is to extract the functions for NAT processing
from OVS and TC to netfilter.
To make this change clear and safe, this patchset gets the common code
out of OVS and TC step by step: The patch 1-4 make some minor changes
in OVS and TC to make the NAT code of them completely the same, then
the patch 5 moves the common code to the netfilter and exports one
function called by each of OVS and TC.
v1->v2:
- Create nf_nat_ovs.c to include the nat functions, as Pablo suggested.
v2->v3:
- fix a typo in subject of patch 2/5, as Marcelo noticed.
- fix in openvswitch to keep OVS ct nat and TC ct nat consistent in
patch 3/5 instead of in tc, as Marcelo noticed.
- use BIT(var) macro instead of (1 << var) in patch 5/5, as Marcelo
suggested.
- use ifdef in netfilter/Makefile to build nf_nat_ovs only when OVS
or TC ct action is enabled in patch 5/5, as Marcelo suggested.
v3->v4:
- add NF_NAT_OVS in netfilter/Kconfig and add select NF_NAT_OVS in
OVS and TC Kconfig instead of using ifdef in netfilter/Makefile,
as Pablo suggested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two nat functions are nearly the same in both OVS and
TC code, (ovs_)ct_nat_execute() and ovs_ct_nat/tcf_ct_act_nat().
This patch creates nf_nat_ovs.c under netfilter and moves them
there then exports nf_ct_nat() so that it can be shared by both
OVS and TC, and keeps the nat (type) check and nat flag update
in OVS and TC's own place, as these parts are different between
OVS and TC.
Note that in OVS nat function it was using skb->protocol to get
the proto as it already skips vlans in key_extract(), while it
doesn't in TC, and TC has to call skb_protocol() to get proto.
So in nf_ct_nat_execute(), we keep using skb_protocol() which
works for both OVS and TC contrack.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ovs_ct_nat_execute(), the packet flow key nat flags are updated
when it processes ICMP(v6) error packets translation successfully.
In ct_nat_execute() when processing ICMP(v6) error packets translation
successfully, it should have done the same in ct_nat_execute() to set
post_ct_s/dnat flag, which will be used to update flow key nat flags
in OVS module later.
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When it fails to allocate nat ext, the packet should be dropped, like
the memory allocation failures in other places in ovs_ct_nat().
This patch changes to return NF_DROP when fails to add nat ext before
doing NAT in ovs_ct_nat(), also it would keep consistent with tc
action ct' processing in tcf_ct_act_nat().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Either OVS_CT_SRC_NAT or OVS_CT_DST_NAT is set, OVS_CT_NAT must be
set in info->nat. Thus, if OVS_CT_NAT is not set in info->nat, it
will definitely not do NAT but returns NF_ACCEPT in ovs_ct_nat().
This patch changes nothing funcational but only makes this return
earlier in ovs_ct_nat() to keep consistent with TC's processing
in tcf_ct_act_nat().
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calls to ovs_ct_nat_execute() are as below:
ovs_ct_execute()
ovs_ct_lookup()
__ovs_ct_lookup()
ovs_ct_nat()
ovs_ct_nat_execute()
ovs_ct_commit()
__ovs_ct_lookup()
ovs_ct_nat()
ovs_ct_nat_execute()
and since skb_pull_rcsum() and skb_push_rcsum() are already
called in ovs_ct_execute(), there's no need to do it again
in ovs_ct_nat_execute().
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are cables that exist that can support speeds in excess of 10GbE.
The driver, however, restricts the EEPROM advertised nominal bitrate to
a specific range, which can prevent usage of cables that can support,
for example, up to 25GbE.
Rather than checking that an active or passive cable supports a specific
range, only check for a minimum supported speed.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP+ active and passive cables are copper cables with fixed SFP+ end
connectors. Due to a misinterpretation of this, SFP+ active cables could
end up not being recognized, causing the driver to fail to establish a
connection.
Introduce a new enum in SFP+ cable types, XGBE_SFP_CABLE_FIBER, that is
the default cable type, and handle active and passive cables when they are
specifically detected.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the behaviour of ip6_datagram_connect to consider the interface
set by the IPV6_UNICAST_IF socket option, similarly to udpv6_sendmsg.
This change is the IPv6 counterpart of the fix for IP_UNICAST_IF.
The tests introduced by that patch showed that the incorrect
behavior is present in IPv6 as well.
This patch fixes the broken test.
Reported-by: kernel test robot <oliver.sang@intel.com>
Link: https://lore.kernel.org/r/202210062117.c7eef1a3-oliver.sang@intel.com
Fixes: 0e4d354762 ("net-next: Fix IP_UNICAST_IF option behavior for connected sockets")
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Yingliang says:
====================
net: don't call dev_kfree_skb() under spin_lock_irqsave()
It is not allowed to call consume_skb() from hardware interrupt context
or with interrupts being disabled. This patchset replace dev_kfree_skb()
with dev_kfree_skb_irq/dev_consume_skb_irq() under spin_lock_irqsave()
in some drivers, or move dev_kfree_skb() after spin_unlock_irqrestore().
v2 -> v3:
Update commit message, and change to use dev_kfree_skb_irq() in patch #1, #3.
v1 -> v2:
patch #2 Move dev_kfree_skb() after spin_unlock_irqrestore()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In these two cases, dev_kfree_skb() is called consume the xmited SKB,
so replace it with dev_consume_skb_irq().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In scc_discard_buffers(), dev_kfree_skb() is called to discard the SKBs,
so replace it with dev_kfree_skb_irq().
In scc_net_tx(), dev_kfree_skb() is called to drop the SKB that exceed
queue length, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
In this case, the lock is used to protected 'bp', so we can move
dev_kfree_skb() after the spin_unlock_irqrestore().
Fixes: 4796417417 ("dnet: Dave DNET ethernet controller driver (updated)")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in xemaclite_tx_timeout() to
drop the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: bb81b2ddfa ("net: add Xilinx emac lite device driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in bmac_tx_timeout() to drop
the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in mace_tx_timeout() to drop
the SKB, when tx timeout, so replace it with dev_kfree_skb_irq().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition in vxlan that when deleting a vxlan device
during receiving packets, there is a possibility that the sock is
released after getting vxlan_sock vs from sk_user_data. Then in
later vxlan_ecn_decapsulate(), vxlan_get_sk_family() we will got
NULL pointer dereference. e.g.
#0 [ffffa25ec6978a38] machine_kexec at ffffffff8c669757
#1 [ffffa25ec6978a90] __crash_kexec at ffffffff8c7c0a4d
#2 [ffffa25ec6978b58] crash_kexec at ffffffff8c7c1c48
#3 [ffffa25ec6978b60] oops_end at ffffffff8c627f2b
#4 [ffffa25ec6978b80] page_fault_oops at ffffffff8c678fcb
#5 [ffffa25ec6978bd8] exc_page_fault at ffffffff8d109542
#6 [ffffa25ec6978c00] asm_exc_page_fault at ffffffff8d200b62
[exception RIP: vxlan_ecn_decapsulate+0x3b]
RIP: ffffffffc1014e7b RSP: ffffa25ec6978cb0 RFLAGS: 00010246
RAX: 0000000000000008 RBX: ffff8aa000888000 RCX: 0000000000000000
RDX: 000000000000000e RSI: ffff8a9fc7ab803e RDI: ffff8a9fd1168700
RBP: ffff8a9fc7ab803e R8: 0000000000700000 R9: 00000000000010ae
R10: ffff8a9fcb748980 R11: 0000000000000000 R12: ffff8a9fd1168700
R13: ffff8aa000888000 R14: 00000000002a0000 R15: 00000000000010ae
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffffa25ec6978ce8] vxlan_rcv at ffffffffc10189cd [vxlan]
#8 [ffffa25ec6978d90] udp_queue_rcv_one_skb at ffffffff8cfb6507
#9 [ffffa25ec6978dc0] udp_unicast_rcv_skb at ffffffff8cfb6e45
#10 [ffffa25ec6978dc8] __udp4_lib_rcv at ffffffff8cfb8807
#11 [ffffa25ec6978e20] ip_protocol_deliver_rcu at ffffffff8cf76951
#12 [ffffa25ec6978e48] ip_local_deliver at ffffffff8cf76bde
#13 [ffffa25ec6978ea0] __netif_receive_skb_one_core at ffffffff8cecde9b
#14 [ffffa25ec6978ec8] process_backlog at ffffffff8cece139
#15 [ffffa25ec6978f00] __napi_poll at ffffffff8ceced1a
#16 [ffffa25ec6978f28] net_rx_action at ffffffff8cecf1f3
#17 [ffffa25ec6978fa0] __softirqentry_text_start at ffffffff8d4000ca
#18 [ffffa25ec6978ff0] do_softirq at ffffffff8c6fbdc3
Reproducer: https://github.com/Mellanox/ovs-tests/blob/master/test-ovs-vxlan-remove-tunnel-during-traffic.sh
Fix this by waiting for all sk_user_data reader to finish before
releasing the sock.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Fixes: 6a93cc9052 ("udp-tunnel: Add a few more UDP tunnel APIs")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called in free_tx_buffers() to drop
the SKBs in tx buffers, when the card is down, so replace it with
dev_kfree_skb_irq() here.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Melnychenko says:
====================
TUN/VirtioNet USO features support.
Added new offloads for TUN devices TUN_F_USO4 and TUN_F_USO6.
Technically they enable NETIF_F_GSO_UDP_L4
(and only if USO4 & USO6 are set simultaneously).
It allows the transmission of large UDP packets.
UDP Segmentation Offload (USO/GSO_UDP_L4) - ability to split UDP packets
into several segments. It's similar to UFO, except it doesn't use IP
fragmentation. The drivers may push big packets and the NIC will split
them(or assemble them in case of receive), but in the case of VirtioNet
we just pass big UDP to the host. So we are freeing the driver from doing
the unnecessary job of splitting. The same thing for several guests
on one host, we can pass big packets between guests.
Different features USO4 and USO6 are required for qemu where Windows
guests can enable disable USO receives for IPv4 and IPv6 separately.
On the other side, Linux can't really differentiate USO4 and USO6, for now.
For now, to enable USO for TUN it requires enabling USO4 and USO6 together.
In the future, there would be a mechanism to control UDP_L4 GSO separately.
New types for virtio-net already in virtio-net specification:
https://github.com/oasis-tcs/virtio-spec/issues/120
Test it WIP Qemu https://github.com/daynix/qemu/tree/USOv3
Changes since v4 & RFC:
* Fixed typo and refactored.
* Tun USO offload refactored.
* Add support for guest-to-guest segmentation offload (thx Jason).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, it possible to enable GSO_UDP_L4("tx-udp-segmentation") for VirtioNet.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, it's possible to convert USO vnet packets from/to skb.
Added support for GSO_UDP_L4 offload.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added new GSO type for USO: VIRTIO_NET_HDR_GSO_UDP_L4.
Feature VIRTIO_NET_F_HOST_USO allows to enable NETIF_F_GSO_UDP_L4.
Separated VIRTIO_NET_F_GUEST_USO4 & VIRTIO_NET_F_GUEST_USO6 features
required for Windows guests.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for USO4 and USO6.
For now, to "enable" USO, it's required to set both USO4 and USO6 simultaneously.
USO enables NETIF_F_GSO_UDP_L4.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added 2 additional offlloads for USO(IPv4 & IPv6).
Separate offloads are required for Windows VM guests,
g.e. Windows may set USO rx only for IPv4.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
