[ Upstream commit ca156e006a ]
ZAC support added sense data requesting on error for both ZAC and ATA
devices. This seems to cause erratic error handling behaviors on some
SSDs where the device reports sense data availability and then
delivers the wrong content making EH take the wrong actions. The
failure mode was sporadic on a LITE-ON ssd and couldn't be reliably
reproduced.
There is no value in requesting sense data from non-ZAC ATA devices
while there's a significant risk of introducing EH misbehaviors which
are difficult to reproduce and fix. Let's do the sense data dancing
only for ZAC devices.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Masato Suzuki <masato.suzuki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f83cfdb1a ]
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd6f32f786 ]
These devices support read zero after trim (RZAT), as they advertise to
the OS. However, the OS doesn't believe the SSDs unless they are
explicitly whitelisted.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d312fefea8 ]
ahci_pci_reset_controller() calls ahci_reset_controller(), which may
fail, but ignores the result code and always returns success. This
may result in failures like below
ahci 0000:02:00.0: version 3.0
ahci 0000:02:00.0: enabling device (0000 -> 0003)
ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
ahci 0000:02:00.0: controller reset failed (0xffffffff)
ahci 0000:02:00.0: failed to stop engine (-5)
... repeated many times ...
ahci 0000:02:00.0: failed to stop engine (-5)
Unable to handle kernel paging request at virtual address ffff0000093f9018
...
PC is at ahci_stop_engine+0x5c/0xd8 [libahci]
LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
...
[<ffff000000a17014>] ahci_stop_engine+0x5c/0xd8 [libahci]
[<ffff000000a196b4>] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
[<ffff000000a197d8>] ahci_init_controller+0x80/0x168 [libahci]
[<ffff000000a260f8>] ahci_pci_init_controller+0x60/0x68 [ahci]
[<ffff000000a26f94>] ahci_init_one+0x75c/0xd88 [ahci]
[<ffff000008430324>] local_pci_probe+0x3c/0xb8
[<ffff000008431728>] pci_device_probe+0x138/0x170
[<ffff000008585e54>] driver_probe_device+0x2dc/0x458
[<ffff0000085860e4>] __driver_attach+0x114/0x118
[<ffff000008583ca8>] bus_for_each_dev+0x60/0xa0
[<ffff000008585638>] driver_attach+0x20/0x28
[<ffff0000085850b0>] bus_add_driver+0x1f0/0x2a8
[<ffff000008586ae0>] driver_register+0x60/0xf8
[<ffff00000842f9b4>] __pci_register_driver+0x3c/0x48
[<ffff000000a3001c>] ahci_pci_driver_init+0x1c/0x1000 [ahci]
[<ffff000008083918>] do_one_initcall+0x38/0x120
where an obvious hardware level failure results in an unnecessary 15 second
delay and a subsequent crash.
So record the result code of ahci_reset_controller() and relay it, rather
than ignoring it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7cf69ae17 ]
ata_parse_force_one() was incorrectly comparing @p to @endp when it
should have been comparing @id. The only consequence is that it may
end up using an invalid port number in "libata.force" module param
instead of rejecting it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Petru-Florin Mihancea <petrum@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195785
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2dbb3ec29a ]
We have seen that on some platforms, SATA device never show any DEVSLP
residency. This prevent power gating of SATA IP, which prevent system
to transition to low power mode in systems with SLP_S0 aka modern
standby systems. The PHY logic is off only in DEVSLP not in slumber.
Reference:
https://www.intel.com/content/dam/www/public/us/en/documents/datasheets
/332995-skylake-i-o-platform-datasheet-volume-1.pdf
Section 28.7.6.1
Here driver is trying to do read-modify-write the devslp register. But
not resetting the bits for which this driver will modify values (DITO,
MDAT and DETO). So simply reset those bits before updating to new values.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fae2a63737 ]
Currently smatch warns of possible Spectre-V1 issue in ahci_led_store():
drivers/ata/libahci.c:1150 ahci_led_store() warn: potential spectre issue 'pp->em_priv' (local cap)
Userspace controls @pmp from following callchain:
em_message->store()
->ata_scsi_em_message_store()
-->ap->ops->em_store()
--->ahci_led_store()
After the mask+shift @pmp is effectively an 8b value, which is used to
index into an array of length 8, so sanitize the array index.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 804689ad2d ]
For failed commands with valid sense data (e.g. NCQ commands),
scsi_check_sense() is used in ata_analyze_tf() to determine if the
command can be retried. In such case, rely on this decision and ignore
the command error mask based decision done in ata_worth_retry().
This fixes useless retries of commands such as unaligned writes on zoned
disks (TYPE_ZAC).
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 240630e618 upstream.
There have been several reports of LPM related hard freezes about once
a day on multiple Lenovo 50 series models. Strange enough these reports
where not disk model specific as LPM issues usually are and some users
with the exact same disk + laptop where seeing them while other users
where not seeing these issues.
It turns out that enabling LPM triggers a firmware bug somewhere, which
has been fixed in later BIOS versions.
This commit adds a new ahci_broken_lpm() function and a new ATA_FLAG_NO_LPM
for dealing with this.
The ahci_broken_lpm() function contains DMI match info for the 4 models
which are known to be affected by this and the DMI BIOS date field for
known good BIOS versions. If the BIOS date is older then the one in the
table LPM will be disabled and a warning will be printed.
Note the BIOS dates are for known good versions, some older versions may
work too, but we don't know for sure, the table is using dates from BIOS
versions for which users have confirmed that upgrading to that version
makes the problem go away.
Unfortunately I've been unable to get hold of the reporter who reported
that BIOS version 2.35 fixed the problems on the W541 for him. I've been
able to verify the DMI_SYS_VENDOR and DMI_PRODUCT_VERSION from an older
dmidecode, but I don't know the exact BIOS date as reported in the DMI.
Lenovo keeps a changelog with dates in their release notes, but the
dates there are the release dates not the build dates which are in DMI.
So I've chosen to set the date to which we compare to one day past the
release date of the 2.34 BIOS. I plan to fix this with a follow up
commit once I've the necessary info.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b320a0a9f2 upstream.
The block (LBA) specified must not exceed the last addressable LBA,
which is dev->nr_sectors - 1. So fix the correct check is
"if (block >= dev->n_sectors)" and not "if (block > dev->n_sectords)".
Additionally, the asc/ascq to return for an LBA that is not a zone start
LBA should be ILLEGAL REQUEST, regardless if the bad LBA is out of
range.
Reported-by: David Butterfield <david.butterfield@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cfce3a86b upstream.
Commit 184add2ca2 ("libata: Apply NOLPM quirk for SanDisk
SD7UB3Q*G1001 SSDs") disabled LPM for SanDisk SD7UB3Q*G1001 SSDs.
This has lead to several reports of users of that SSD where LPM
was working fine and who know have a significantly increased idle
power consumption on their laptops.
Likely there is another problem on the T450s from the original
reporter which gets exposed by the uncore reaching deeper sleep
states (higher PC-states) due to LPM being enabled. The problem as
reported, a hardfreeze about once a day, already did not sound like
it would be caused by LPM and the reports of the SSD working fine
confirm this. The original reporter is ok with dropping the quirk.
A X250 user has reported the same hard freeze problem and for him
the problem went away after unrelated updates, I suspect some GPU
driver stack changes fixed things.
TL;DR: The original reporters problem were triggered by LPM but not
an LPM issue, so drop the quirk for the SSD in question.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1583207
Cc: stable@vger.kernel.org
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Lorenzo Dalrio <lorenzo.dalrio@gmail.com>
Reported-by: Lorenzo Dalrio <lorenzo.dalrio@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "Richard W.M. Jones" <rjones@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 795ef78814 upstream.
Don't populate the arrays cdb on the stack, instead make them static.
Makes the object code smaller by 230 bytes:
Before:
text data bss dec hex filename
3797 240 0 4037 fc5 drivers/ata/libata-zpodd.o
After:
text data bss dec hex filename
3407 400 0 3807 edf drivers/ata/libata-zpodd.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0d3e45bc65 ]
This fixs the following comile warnings with ATA_DEBUG enabled,
which detected by Linaro GCC 5.2-2015.11:
drivers/ata/libata-scsi.c: In function 'ata_scsi_dump_cdb':
./include/linux/kern_levels.h:5:18: warning: format '%d' expects
argument of type 'int', but argument 6 has type 'u64 {aka long
long unsigned int}' [-Wformat=]
tj: Patch hand-applied and description trimmed.
Signed-off-by: Dong Bo <dongbo4@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 136d769e0b upstream.
While whitelisting Micron M500DC drives, the tweaked blacklist entry
enabled queued TRIM from M500IT variants also. But these do not support
queued TRIM. And while using those SSDs with the latest kernel we have
seen errors and even the partition table getting corrupted.
Some part from the dmesg:
[ 6.727384] ata1.00: ATA-9: Micron_M500IT_MTFDDAK060MBD, MU01, max UDMA/133
[ 6.727390] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 6.741026] ata1.00: supports DRM functions and may not be fully accessible
[ 6.759887] ata1.00: configured for UDMA/133
[ 6.762256] scsi 0:0:0:0: Direct-Access ATA Micron_M500IT_MT MU01 PQ: 0 ANSI: 5
and then for the error:
[ 120.860334] ata1.00: exception Emask 0x1 SAct 0x7ffc0007 SErr 0x0 action 0x6 frozen
[ 120.860338] ata1.00: irq_stat 0x40000008
[ 120.860342] ata1.00: failed command: SEND FPDMA QUEUED
[ 120.860351] ata1.00: cmd 64/01:00:00:00:00/00:00:00:00:00/a0 tag 0 ncq dma 512 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x5 (timeout)
[ 120.860353] ata1.00: status: { DRDY }
[ 120.860543] ata1: hard resetting link
[ 121.166128] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 121.166376] ata1.00: supports DRM functions and may not be fully accessible
[ 121.186238] ata1.00: supports DRM functions and may not be fully accessible
[ 121.204445] ata1.00: configured for UDMA/133
[ 121.204454] ata1.00: device reported invalid CHS sector 0
[ 121.204541] sd 0:0:0:0: [sda] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[ 121.204546] sd 0:0:0:0: [sda] tag#18 Sense Key : 0x5 [current]
[ 121.204550] sd 0:0:0:0: [sda] tag#18 ASC=0x21 ASCQ=0x4
[ 121.204555] sd 0:0:0:0: [sda] tag#18 CDB: opcode=0x93 93 08 00 00 00 00 00 04 28 80 00 00 00 30 00 00
[ 121.204559] print_req_error: I/O error, dev sda, sector 272512
After few reboots with these errors, and the SSD is corrupted.
After blacklisting it, the errors are not seen and the SSD does not get
corrupted any more.
Fixes: 243918be63 ("libata: Do not blacklist Micron M500DC")
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 184add2ca2 upstream.
Richard Jones has reported that using med_power_with_dipm on a T450s
with a Sandisk SD7UB3Q256G1001 SSD (firmware version X2180501) is
causing the machine to hang.
Switching the LPM to max_performance fixes this, so it seems that
this Sandisk SSD does not handle LPM well.
Note in the past there have been bug-reports about the following
Sandisk models not working with min_power, so we may need to extend
the quirk list in the future: name - firmware
Sandisk SD6SB2M512G1022I - X210400
Sandisk SD6PP4M-256G-1006 - A200906
Cc: stable@vger.kernel.org
Cc: Richard W.M. Jones <rjones@redhat.com>
Reported-and-tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c034640a32 ]
When platform_get_irq() fails, it returns an error code, which
libahci_platform and replaces it by -EINVAL. This commit fixes that by
propagating the error code. It fixes the situation where
platform_get_irq() returns -EPROBE_DEFER because the interrupt
controller is not available yet, and generally looks like the right
thing to do.
We pay attention to not show the "no irq" message when we are in an
EPROBE_DEFER situation, because the driver probing will be retried
later on, once the interrupt controller becomes available to provide
the interrupt.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d418ff56b8 upstream.
When commit 9c7be59fc5 ("libata: Apply NOLPM quirk to Crucial MX100
512GB SSDs") was added it inherited the ATA_HORKAGE_NO_NCQ_TRIM quirk
from the existing "Crucial_CT*MX100*" entry, but that entry sets model_rev
to "MU01", where as the entry adding the NOLPM quirk sets it to NULL.
This means that after this commit we no apply the NO_NCQ_TRIM quirk to
all "Crucial_CT512MX100*" SSDs even if they have the fixed "MU02"
firmware. This commit splits the "Crucial_CT512MX100*" quirk into 2
quirks, one for the "MU01" firmware and one for all other firmware
versions, so that we once again only apply the NO_NCQ_TRIM quirk to the
"MU01" firmware version.
Fixes: 9c7be59fc5 ("libata: Apply NOLPM quirk to ... MX100 512GB SSDs")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bf7b5d6d0 upstream.
Commit b17e5729a6 ("libata: disable LPM for Crucial BX100 SSD 500GB
drive"), introduced a ATA_HORKAGE_NOLPM quirk for Crucial BX100 500GB SSDs
but limited this to the MU02 firmware version, according to:
http://www.crucial.com/usa/en/support-ssd-firmware
MU02 is the last version, so there are no newer possibly fixed versions
and if the MU02 version has broken LPM then the MU01 almost certainly
also has broken LPM, so this commit changes the quirk to apply to all
firmware versions.
Fixes: b17e5729a6 ("libata: disable LPM for Crucial BX100 SSD 500GB...")
Cc: stable@vger.kernel.org
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62ac3f7305 upstream.
There have been reports of the Crucial M500 480GB model not working
with LPM set to min_power / med_power_with_dipm level.
It has not been tested with medium_power, but that typically has no
measurable power-savings.
Note the reporters Crucial_CT480M500SSD3 has a firmware version of MU03
and there is a MU05 update available, but that update does not mention any
LPM fixes in its changelog, so the quirk matches all firmware versions.
In my experience the LPM problems with (older) Crucial SSDs seem to be
limited to higher capacity versions of the SSDs (different firmware?),
so this commit adds a NOLPM quirk for the 480 and 960GB versions of the
M500, to avoid LPM causing issues with these SSDs.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Martin Steigerwald <martin@lichtvoll.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c7be59fc5 upstream.
Various people have reported the Crucial MX100 512GB model not working
with LPM set to min_power. I've now received a report that it also does
not work with the new med_power_with_dipm level.
It does work with medium_power, but that has no measurable power-savings
and given the amount of people being bitten by the other levels not
working, this commit just disables LPM altogether.
Note all reporters of this have either the 512GB model (max capacity), or
are not specifying their SSD's size. So for now this quirk assumes this is
a problem with the 512GB model only.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=89261
Buglink: https://github.com/linrunner/TLP/issues/84
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c1ec6fda2 upstream.
syzkaller hit a WARN() in ata_bmdma_qc_issue() when writing to /dev/sg0.
This happened because it issued an ATA pass-through command (ATA_16)
where the protocol field indicated that NCQ should be used -- but the
device did not support NCQ.
We could just remove the WARN() from libata-sff.c, but the real problem
seems to be that the SCSI -> ATA translation code passes through NCQ
commands without verifying that the device actually supports NCQ.
Fix this by adding the appropriate check to ata_scsi_pass_thru().
Here's reproducer that works in QEMU when /dev/sg0 refers to a disk of
the default type ("82371SB PIIX3 IDE"):
#include <fcntl.h>
#include <unistd.h>
int main()
{
char buf[53] = { 0 };
buf[36] = 0x85; /* ATA_16 */
buf[37] = (12 << 1); /* FPDMA */
buf[38] = 0x1; /* Has data */
buf[51] = 0xC8; /* ATA_CMD_READ */
write(open("/dev/sg0", O_RDWR), buf, sizeof(buf));
}
Fixes: ee7fb331c3 ("libata: add support for NCQ commands for SG interface")
Reported-by: syzbot+2f69ca28df61bdfc77cd36af2e789850355a221e@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9173e5e807 upstream.
syzkaller hit a WARN() in ata_qc_issue() when writing to /dev/sg0. This
happened because it issued a READ_6 command with no data buffer.
Just remove the WARN(), as it doesn't appear indicate a kernel bug. The
expected behavior is to fail the command, which the code does.
Here's a reproducer that works in QEMU when /dev/sg0 refers to a disk of
the default type ("82371SB PIIX3 IDE"):
#include <fcntl.h>
#include <unistd.h>
int main()
{
char buf[42] = { [36] = 0x8 /* READ_6 */ };
write(open("/dev/sg0", O_RDWR), buf, sizeof(buf));
}
Fixes: f92a26365a ("libata: change ATA_QCFLAG_DMAMAP semantics")
Reported-by: syzbot+f7b556d1766502a69d85071d2ff08bd87be53d0f@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # v2.6.25+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 058f58e235 upstream.
syzkaller reported a crash in ata_bmdma_fill_sg() when writing to
/dev/sg1. The immediate cause was that the ATA command's scatterlist
was not DMA-mapped, which causes 'pi - 1' to underflow, resulting in a
write to 'qc->ap->bmdma_prd[0xffffffff]'.
Strangely though, the flag ATA_QCFLAG_DMAMAP was set in qc->flags. The
root cause is that when __ata_scsi_queuecmd() is preparing to relay a
SCSI command to an ATAPI device, it doesn't correctly validate the CDB
length before copying it into the 16-byte buffer 'cdb' in 'struct
ata_queued_cmd'. Namely, it validates the fixed CDB length expected
based on the SCSI opcode but not the actual CDB length, which can be
larger due to the use of the SG_NEXT_CMD_LEN ioctl. Since 'flags' is
the next member in ata_queued_cmd, a buffer overflow corrupts it.
Fix it by requiring that the actual CDB length be <= 16 (ATAPI_CDB_LEN).
[Really it seems the length should be required to be <= dev->cdb_len,
but the current behavior seems to have been intentionally introduced by
commit 607126c2a2 ("libata-scsi: be tolerant of 12-byte ATAPI commands
in 16-byte CDBs") to work around a userspace bug in mplayer. Probably
the workaround is no longer needed (mplayer was fixed in 2007), but
continuing to allow lengths to up 16 appears harmless for now.]
Here's a reproducer that works in QEMU when /dev/sg1 refers to the
CD-ROM drive that qemu-system-x86_64 creates by default:
#include <fcntl.h>
#include <sys/ioctl.h>
#include <unistd.h>
#define SG_NEXT_CMD_LEN 0x2283
int main()
{
char buf[53] = { [36] = 0x7e, [52] = 0x02 };
int fd = open("/dev/sg1", O_RDWR);
ioctl(fd, SG_NEXT_CMD_LEN, &(int){ 17 });
write(fd, buf, sizeof(buf));
}
The crash was:
BUG: unable to handle kernel paging request at ffff8cb97db37ffc
IP: ata_bmdma_fill_sg drivers/ata/libata-sff.c:2623 [inline]
IP: ata_bmdma_qc_prep+0xa4/0xc0 drivers/ata/libata-sff.c:2727
PGD fb6c067 P4D fb6c067 PUD 0
Oops: 0002 [#1] SMP
CPU: 1 PID: 150 Comm: syz_ata_bmdma_q Not tainted 4.15.0-next-20180202 #99
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
[...]
Call Trace:
ata_qc_issue+0x100/0x1d0 drivers/ata/libata-core.c:5421
ata_scsi_translate+0xc9/0x1a0 drivers/ata/libata-scsi.c:2024
__ata_scsi_queuecmd drivers/ata/libata-scsi.c:4326 [inline]
ata_scsi_queuecmd+0x8c/0x210 drivers/ata/libata-scsi.c:4375
scsi_dispatch_cmd+0xa2/0xe0 drivers/scsi/scsi_lib.c:1727
scsi_request_fn+0x24c/0x530 drivers/scsi/scsi_lib.c:1865
__blk_run_queue_uncond block/blk-core.c:412 [inline]
__blk_run_queue+0x3a/0x60 block/blk-core.c:432
blk_execute_rq_nowait+0x93/0xc0 block/blk-exec.c:78
sg_common_write.isra.7+0x272/0x5a0 drivers/scsi/sg.c:806
sg_write+0x1ef/0x340 drivers/scsi/sg.c:677
__vfs_write+0x31/0x160 fs/read_write.c:480
vfs_write+0xa7/0x160 fs/read_write.c:544
SYSC_write fs/read_write.c:589 [inline]
SyS_write+0x4d/0xc0 fs/read_write.c:581
do_syscall_64+0x5e/0x110 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x21/0x86
Fixes: 607126c2a2 ("libata-scsi: be tolerant of 12-byte ATAPI commands in 16-byte CDBs")
Reported-by: syzbot+1ff6f9fcc3c35f1c72a95e26528c8e7e3276e4da@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # v2.6.24+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 998008b779 upstream.
Add PCI ids for Intel Bay Trail, Cherry Trail and Apollo Lake AHCI
SATA controllers. This commit is a preparation patch for allowing a
different default sata link powermanagement policy for mobile chipsets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca1b4974bd upstream.
Intel uses different SATA PCI ids for the Desktop and Mobile SKUs of their
chipsets. For older models the comment describing which chipset the PCI id
is for, aksi indicates when we're dealing with a mobile SKU. Extend the
comments for recent chipsets to also indicate mobile SKUs.
The information this commit adds comes from Intel's chipset datasheets.
This commit is a preparation patch for allowing a different default
sata link powermanagement policy for mobile chipsets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db5ff90979 upstream.
LITEON EP1 has the same timeout issues as CX1 series devices.
Revert max_sectors to the value of 1024.
Fixes: e0edc8c546 ("libata: apply MAX_SEC_1024 to all CX1-JB*-HP devices")
Signed-off-by: Xinyu Lin <xinyu0123@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0580b762a4 ]
ata_sff_qc_issue() expects upper layers to never issue commands on a
command protocol that it doesn't implement. While the assumption
holds fine with the usual IO path, nothing filters based on the
command protocol in the passthrough path (which was added later),
allowing the warning to be tripped with a passthrough command with the
right (well, wrong) protocol.
Failing with AC_ERR_SYSTEM is the right thing to do anyway. Remove
the unnecessary WARN.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/r/CACT4Y+bXkvevNZU8uP6X0QVqsj6wNoUA_1exfTSOzc+SmUtMOA@mail.gmail.com
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1601113dd upstream.
When tracing ata link error event, the kernel crashes when the disk is
removed due to NULL pointer access by trace_ata_eh_link_autopsy API.
This occurs as the dev is NULL when the disk disappeared. This patch
fixes this crash by calling trace_ata_eh_link_autopsy only if "dev"
is not NULL.
v2 changes:
Removed direct passing "link" pointer instead of "dev" in trace API.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 255c03d15a ("libata: Add tracepoints")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d85fc67dd1 ]
Without this patch, failed probe would not free resources like irq.
ata port tdev object currently hold a reference to the ata port
object. Therefore the ata port object release function will not get
called until the ata_tport_release is called. But that would never
happen, releasing the last reference of ata port dev is done by
scsi_host_release, which is called by ata_host_release when the ata
port object is released.
The ata device objects actually do not need to explicitly hold a
reference to their real counterpart, given the transport objects are
the children of these objects and device_add() is call for each child.
We know the parent will not be deleted until we call the child's
device_del().
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Tested-by: Matthew Whitehead <tedheadster@gmail.com>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 591b6bb605 upstream.
Several legacy devices such as Geode-based Cisco ASA appliances
and DB800 development board do possess CS5536 IDE controller
with different PCI id than existing one. Using pata_generic is
not always feasible as at least DB800 requires MSR quirk from
pata_cs5536 to be used with vendor firmware.
Signed-off-by: Andrey Korolyov <andrey@xdel.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59a5e266c3 upstream.
My static checker complains that "devno" can be negative, meaning that
we read before the start of the loop. I've looked at the code, and I
think the warning is right. This come from /proc so it's root only or
it would be quite a quite a serious bug. The call tree looks like this:
proc_scsi_write() <- gets id and channel from simple_strtoul()
-> scsi_add_single_device() <- calls shost->transportt->user_scan()
-> ata_scsi_user_scan()
-> ata_find_dev()
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bfd174312 upstream.
(Correction in this resend: fixed function name acer_sa5_271_workaround; fixed
the always-true condition in the function; fixed description.)
On the Acer Switch Alpha 12 (model number: SA5-271), the internal SSD may not
get detected because the port_map and CAP.nr_ports combination causes the driver
to skip the port that is actually connected to the SSD. More specifically,
either all SATA ports are identified as DUMMY, or all ports get ``link down''
and never get up again.
This problem occurs occasionally. When this problem occurs, CAP may hold a
value of 0xC734FF00 or 0xC734FF01 and port_map may hold a value of 0x00 or 0x01.
When this problem does not occur, CAP holds a value of 0xC734FF02 and port_map
may hold a value of 0x07. Overriding the CAP value to 0xC734FF02 and port_map to
0x7 significantly reduces the occurrence of this problem.
Link: https://bugzilla.kernel.org/attachment.cgi?id=253091
Signed-off-by: Sui Chen <suichen6@gmail.com>
Tested-by: Damian Ivanov <damianatorrpm@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f4d435f326 ]
There's an issue with the da850 SATA controller: if port multiplier
support is compiled in, but we're connecting the drive directly to
the SATA port on the board, the drive can't be detected.
To make SATA work on the da850-lcdk board: first try to softreset
with pmp - if the operation fails with -EBUSY, retry without pmp.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2dae99558e upstream.
For an ATA device supporting the sense data reporting feature set, a
failed command will trigger the execution of ata_eh_request_sense if
the result task file of the failed command has the ATA_SENSE bit set
(sense data available bit). ata_eh_request_sense executes the REQUEST
SENSE DATA EXT command to retrieve the sense data of the failed
command. On success of REQUEST SENSE DATA EXT, the ATA_SENSE bit will
NOT be set (the command succeeded) but ata_eh_request_sense
nevertheless tests the availability of sense data by testing that bit
presence in the result tf of the REQUEST SENSE DATA EXT command. This
leads us to falsely assume that request sense data failed and to the
warning message:
atax.xx: request sense failed stat 50 emask 0
Upon success of REQUEST SENSE DATA EXT, set the ATA_SENSE bit in the
result task file command so that sense data can be returned by
ata_eh_request_sense.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0edc8c546 upstream.
Marko reports that CX1-JB512-HP shows the same timeout issues as
CX1-JB256-HP. Let's apply MAX_SEC_128 to all devices in the series.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marko Koski-Vähälä <marko@koski-vahala.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 064c3db9c5 upstream.
Here, If devm_ioremap will fail. It will return NULL.
Then hpriv->base = NULL - 0x20000; Kernel can run into
a NULL-pointer dereference. This error check will avoid
NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
