commit bd293d071f upstream.
When thin-volume is built on loop device, if available memory is low,
the following deadlock can be triggered:
One process P1 allocates memory with GFP_FS flag, direct alloc fails,
memory reclaim invokes memory shrinker in dm_bufio, dm_bufio_shrink_scan()
runs, mutex dm_bufio_client->lock is acquired, then P1 waits for dm_buffer
IO to complete in __try_evict_buffer().
But this IO may never complete if issued to an underlying loop device
that forwards it using direct-IO, which allocates memory using
GFP_KERNEL (see: do_blockdev_direct_IO()). If allocation fails, memory
reclaim will invoke memory shrinker in dm_bufio, dm_bufio_shrink_scan()
will be invoked, and since the mutex is already held by P1 the loop
thread will hang, and IO will never complete. Resulting in ABBA
deadlock.
Cc: stable@vger.kernel.org
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2eba4e640b ]
DM verity should also use DMERR_LIMIT to limit repeat data block
corruption messages.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9642fa73d0 ]
Stopping external metadata arrays during resync/recovery causes
retries, loop of interrupting and starting reconstruction, until it
hit at good moment to stop completely. While these retries
curr_mark_cnt can be small- especially on HDD drives, so subtraction
result can be smaller than 0. However it is casted to uint without
checking. As a result of it the status bar in /proc/mdstat while stopping
is strange (it jumps between 0% and 99%).
The real problem occurs here after commit 72deb455b5 ("block: remove
CONFIG_LBDAF"). Sector_div() macro has been changed, now the
divisor is casted to uint32. For db = -8 the divisior(db/32-1) becomes 0.
Check if db value can be really counted and replace these macro by
div64_u64() inline.
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 31b90956b1 upstream.
Recently people report bcache code compiled with gcc9 is broken, one of
the buggy behavior I observe is that two adjacent 4KB I/Os should merge
into one but they don't. Finally it turns out to be a stack corruption
caused by macro PRECEDING_KEY().
See how PRECEDING_KEY() is defined in bset.h,
437 #define PRECEDING_KEY(_k) \
438 ({ \
439 struct bkey *_ret = NULL; \
440 \
441 if (KEY_INODE(_k) || KEY_OFFSET(_k)) { \
442 _ret = &KEY(KEY_INODE(_k), KEY_OFFSET(_k), 0); \
443 \
444 if (!_ret->low) \
445 _ret->high--; \
446 _ret->low--; \
447 } \
448 \
449 _ret; \
450 })
At line 442, _ret points to address of a on-stack variable combined by
KEY(), the life range of this on-stack variable is in line 442-446,
once _ret is returned to bch_btree_insert_key(), the returned address
points to an invalid stack address and this address is overwritten in
the following called bch_btree_iter_init(). Then argument 'search' of
bch_btree_iter_init() points to some address inside stackframe of
bch_btree_iter_init(), exact address depends on how the compiler
allocates stack space. Now the stack is corrupted.
Fixes: 0eacac2203 ("bcache: PRECEDING_KEY()")
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Rolf Fokkens <rolf@rolffokkens.nl>
Reviewed-by: Pierre JUHEN <pierre.juhen@orange.fr>
Tested-by: Shenghui Wang <shhuiw@foxmail.com>
Tested-by: Pierre JUHEN <pierre.juhen@orange.fr>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Nix <nix@esperi.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78d4eb8ad9 ]
clang has identified a code path in which it thinks a
variable may be unused:
drivers/md/bcache/alloc.c:333:4: error: variable 'bucket' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
fifo_pop(&ca->free_inc, bucket);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/md/bcache/util.h:219:27: note: expanded from macro 'fifo_pop'
#define fifo_pop(fifo, i) fifo_pop_front(fifo, (i))
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/md/bcache/util.h:189:6: note: expanded from macro 'fifo_pop_front'
if (_r) { \
^~
drivers/md/bcache/alloc.c:343:46: note: uninitialized use occurs here
allocator_wait(ca, bch_allocator_push(ca, bucket));
^~~~~~
drivers/md/bcache/alloc.c:287:7: note: expanded from macro 'allocator_wait'
if (cond) \
^~~~
drivers/md/bcache/alloc.c:333:4: note: remove the 'if' if its condition is always true
fifo_pop(&ca->free_inc, bucket);
^
drivers/md/bcache/util.h:219:27: note: expanded from macro 'fifo_pop'
#define fifo_pop(fifo, i) fifo_pop_front(fifo, (i))
^
drivers/md/bcache/util.h:189:2: note: expanded from macro 'fifo_pop_front'
if (_r) { \
^
drivers/md/bcache/alloc.c:331:15: note: initialize the variable 'bucket' to silence this warning
long bucket;
^
This cannot happen in practice because we only enter the loop
if there is at least one element in the list.
Slightly rearranging the code makes this clearer to both the
reader and the compiler, which avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce3e4cfb59 ]
Currently run_cache_set() has no return value, if there is failure in
bch_journal_replay(), the caller of run_cache_set() has no idea about
such failure and just continue to execute following code after
run_cache_set(). The internal failure is triggered inside
bch_journal_replay() and being handled in async way. This behavior is
inefficient, while failure handling inside bch_journal_replay(), cache
register code is still running to start the cache set. Registering and
unregistering code running as same time may introduce some rare race
condition, and make the code to be more hard to be understood.
This patch adds return value to run_cache_set(), and returns -EIO if
bch_journal_rreplay() fails. Then caller of run_cache_set() may detect
such failure and stop registering code flow immedidately inside
register_cache_set().
If journal replay fails, run_cache_set() can report error immediately
to register_cache_set(). This patch makes the failure handling for
bch_journal_replay() be in synchronized way, easier to understand and
debug, and avoid poetential race condition for register-and-unregister
in same time.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 631207314d ]
journal replay failed with messages:
Sep 10 19:10:43 ceph kernel: bcache: error on
bb379a64-e44e-4812-b91d-a5599871a3b1: bcache: journal entries
2057493-2057567 missing! (replaying 2057493-2076601), disabling
caching
The reason is in journal_reclaim(), when discard is enabled, we send
discard command and reclaim those journal buckets whose seq is old
than the last_seq_now, but before we write a journal with last_seq_now,
the machine is restarted, so the journal with the last_seq_now is not
written to the journal bucket, and the last_seq_wrote in the newest
journal is old than last_seq_now which we expect to be, so when we doing
replay, journals from last_seq_wrote to last_seq_now are missing.
It's hard to write a journal immediately after journal_reclaim(),
and it harmless if those missed journal are caused by discarding
since those journals are already wrote to btree node. So, if miss
seqs are started from the beginning journal, we treat it as normal,
and only print a message to show the miss journal, and point out
it maybe caused by discarding.
Patch v2 add a judgement condition to ignore the missed journal
only when discard enabled as Coly suggested.
(Coly Li: rebase the patch with other changes in bch_journal_replay())
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Tested-by: Dennis Schridde <devurandom@gmx.net>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68d10e6979 ]
When failure happens inside bch_journal_replay(), calling
cache_set_err_on() and handling the failure in async way is not a good
idea. Because after bch_journal_replay() returns, registering code will
continue to execute following steps, and unregistering code triggered
by cache_set_err_on() is running in same time. First it is unnecessary
to handle failure and unregister cache set in an async way, second there
might be potential race condition to run register and unregister code
for same cache set.
So in this patch, if failure happens in bch_journal_replay(), we don't
call cache_set_err_on(), and just print out the same error message to
kernel message buffer, then return -EIO immediately caller. Then caller
can detect such failure and handle it in synchrnozied way.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b2176a1dfb upstream.
The problem is that any 'uptodate' vs 'disks' check is not precise
in this path. Put a "WARN_ON(!test_bit(R5_UPTODATE, &dev->flags)" on the
device that might try to kick off writes and then skip the action.
Better to prevent the raid driver from taking unexpected action *and* keep
the system alive vs killing the machine with BUG_ON.
Note: fixed warning reported by kbuild test robot <lkp@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Nigel Croxon <ncroxon@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81bc6d150a upstream.
When the target line contains an invalid device, delay_ctr() will call
delay_dtr() with NULL workqueue. Attempting to destroy the NULL
workqueue causes a crash.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bee2addc0 upstream.
In journal_reclaim() ja->cur_idx of each cache will be update to
reclaim available journal buckets. Variable 'int n' is used to count how
many cache is successfully reclaimed, then n is set to c->journal.key
by SET_KEY_PTRS(). Later in journal_write_unlocked(), a for_each_cache()
loop will write the jset data onto each cache.
The problem is, if all jouranl buckets on each cache is full, the
following code in journal_reclaim(),
529 for_each_cache(ca, c, iter) {
530 struct journal_device *ja = &ca->journal;
531 unsigned int next = (ja->cur_idx + 1) % ca->sb.njournal_buckets;
532
533 /* No space available on this device */
534 if (next == ja->discard_idx)
535 continue;
536
537 ja->cur_idx = next;
538 k->ptr[n++] = MAKE_PTR(0,
539 bucket_to_sector(c, ca->sb.d[ja->cur_idx]),
540 ca->sb.nr_this_dev);
541 }
542
543 bkey_init(k);
544 SET_KEY_PTRS(k, n);
If there is no available bucket to reclaim, the if() condition at line
534 will always true, and n remains 0. Then at line 544, SET_KEY_PTRS()
will set KEY_PTRS field of c->journal.key to 0.
Setting KEY_PTRS field of c->journal.key to 0 is wrong. Because in
journal_write_unlocked() the journal data is written in following loop,
649 for (i = 0; i < KEY_PTRS(k); i++) {
650-671 submit journal data to cache device
672 }
If KEY_PTRS field is set to 0 in jouranl_reclaim(), the journal data
won't be written to cache device here. If system crahed or rebooted
before bkeys of the lost journal entries written into btree nodes, data
corruption will be reported during bcache reload after rebooting the
system.
Indeed there is only one cache in a cache set, there is no need to set
KEY_PTRS field in journal_reclaim() at all. But in order to keep the
for_each_cache() logic consistent for now, this patch fixes the above
problem by not setting 0 KEY_PTRS of journal key, if there is no bucket
available to reclaim.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f4fd7c579 upstream.
Changing state from check_state_check_result to
check_state_compute_result not only is unsafe but also doesn't
appear to serve a valid purpose. A raid6 check should only be
pushing out extra writes if doing repair and a mis-match occurs.
The stripe dev management will already try and do repair writes
for failing sectors.
This patch makes the raid6 check_state_check_result handling
work more like raid5's. If somehow too many failures for a
check, just quit the check operation for the stripe. When any
checks pass, don't try and use check_state_compute_result for
a purpose it isn't needed for and is unsafe for. Just mark the
stripe as in sync for passing its parity checks and let the
stripe dev read/write code and the bad blocks list do their
job handling I/O errors.
Repro steps from Xiao:
These are the steps to reproduce this problem:
1. redefined OPT_MEDIUM_ERR_ADDR to 12000 in scsi_debug.c
2. insmod scsi_debug.ko dev_size_mb=11000 max_luns=1 num_tgts=1
3. mdadm --create /dev/md127 --level=6 --raid-devices=5 /dev/sde1 /dev/sde2 /dev/sde3 /dev/sde5 /dev/sde6
sde is the disk created by scsi_debug
4. echo "2" >/sys/module/scsi_debug/parameters/opts
5. raid-check
It panic:
[ 4854.730899] md: data-check of RAID array md127
[ 4854.857455] sd 5:0:0:0: [sdr] tag#80 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 4854.859246] sd 5:0:0:0: [sdr] tag#80 Sense Key : Medium Error [current]
[ 4854.860694] sd 5:0:0:0: [sdr] tag#80 Add. Sense: Unrecovered read error
[ 4854.862207] sd 5:0:0:0: [sdr] tag#80 CDB: Read(10) 28 00 00 00 2d 88 00 04 00 00
[ 4854.864196] print_req_error: critical medium error, dev sdr, sector 11656 flags 0
[ 4854.867409] sd 5:0:0:0: [sdr] tag#100 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 4854.869469] sd 5:0:0:0: [sdr] tag#100 Sense Key : Medium Error [current]
[ 4854.871206] sd 5:0:0:0: [sdr] tag#100 Add. Sense: Unrecovered read error
[ 4854.872858] sd 5:0:0:0: [sdr] tag#100 CDB: Read(10) 28 00 00 00 2e e0 00 00 08 00
[ 4854.874587] print_req_error: critical medium error, dev sdr, sector 12000 flags 4000
[ 4854.876456] sd 5:0:0:0: [sdr] tag#101 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 4854.878552] sd 5:0:0:0: [sdr] tag#101 Sense Key : Medium Error [current]
[ 4854.880278] sd 5:0:0:0: [sdr] tag#101 Add. Sense: Unrecovered read error
[ 4854.881846] sd 5:0:0:0: [sdr] tag#101 CDB: Read(10) 28 00 00 00 2e e8 00 00 08 00
[ 4854.883691] print_req_error: critical medium error, dev sdr, sector 12008 flags 4000
[ 4854.893927] sd 5:0:0:0: [sdr] tag#166 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 4854.896002] sd 5:0:0:0: [sdr] tag#166 Sense Key : Medium Error [current]
[ 4854.897561] sd 5:0:0:0: [sdr] tag#166 Add. Sense: Unrecovered read error
[ 4854.899110] sd 5:0:0:0: [sdr] tag#166 CDB: Read(10) 28 00 00 00 2e e0 00 00 10 00
[ 4854.900989] print_req_error: critical medium error, dev sdr, sector 12000 flags 0
[ 4854.902757] md/raid:md127: read error NOT corrected!! (sector 9952 on sdr1).
[ 4854.904375] md/raid:md127: read error NOT corrected!! (sector 9960 on sdr1).
[ 4854.906201] ------------[ cut here ]------------
[ 4854.907341] kernel BUG at drivers/md/raid5.c:4190!
raid5.c:4190 above is this BUG_ON:
handle_parity_checks6()
...
BUG_ON(s->uptodate < disks - 1); /* We don't need Q to recover */
Cc: <stable@vger.kernel.org> # v3.16+
OriginalAuthor: David Jeffery <djeffery@redhat.com>
Cc: Xiao Ni <xni@redhat.com>
Tested-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: David Jeffy <djeffery@redhat.com>
Signed-off-by: Nigel Croxon <ncroxon@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 596b5a5dd1 ]
Currently sysfs_strtoul_clamp() is defined as,
82 #define sysfs_strtoul_clamp(file, var, min, max) \
83 do { \
84 if (attr == &sysfs_ ## file) \
85 return strtoul_safe_clamp(buf, var, min, max) \
86 ?: (ssize_t) size; \
87 } while (0)
The problem is, if bit width of var is less then unsigned long, min and
max may not protect var from integer overflow, because overflow happens
in strtoul_safe_clamp() before checking min and max.
To fix such overflow in sysfs_strtoul_clamp(), to make min and max take
effect, this patch adds an unsigned long variable, and uses it to macro
strtoul_safe_clamp() to convert an unsigned long value in range defined
by [min, max]. Then assign this value to var. By this method, if bit
width of var is less than unsigned long, integer overflow won't happen
before min and max are checking.
Now sysfs_strtoul_clamp() can properly handle smaller data type like
unsigned int, of cause min and max should be defined in range of
unsigned int too.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c27a3953e ]
People may set sequential_cutoff of a cached device via sysfs file,
but current code does not check input value overflow. E.g. if value
4294967295 (UINT_MAX) is written to file sequential_cutoff, its value
is 4GB, but if 4294967296 (UINT_MAX + 1) is written into, its value
will be 0. This is an unexpected behavior.
This patch replaces d_strtoi_h() by sysfs_strtoul_clamp() to convert
input string to unsigned integer value, and limit its range in
[0, UINT_MAX]. Then the input overflow can be fixed.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a91fbda49f ]
Cache set sysfs entry io_error_halflife is used to set c->error_decay.
c->error_decay is in type unsigned int, and it is converted by
strtoul_or_return(), therefore overflow to c->error_decay is possible
for a large input value.
This patch fixes the overflow by using strtoul_safe_clamp() to convert
input string to an unsigned long value in range [0, UINT_MAX], then
divides by 88 and set it to c->error_decay.
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70de2cbda8 ]
Invoking dm_get_device() twice on the same device path with different
modes is dangerous. Because in that case, upgrade_mode() will alloc a
new 'dm_dev' and free the old one, which may be referenced by a previous
caller. Dereferencing the dangling pointer will trigger kernel NULL
pointer dereference.
The following two cases can reproduce this issue. Actually, they are
invalid setups that must be disallowed, e.g.:
1. Creating a thin-pool with read_only mode, and the same device as
both metadata and data.
dmsetup create thinp --table \
"0 41943040 thin-pool /dev/vdb /dev/vdb 128 0 1 read_only"
BUG: unable to handle kernel NULL pointer dereference at 0000000000000080
...
Call Trace:
new_read+0xfb/0x110 [dm_bufio]
dm_bm_read_lock+0x43/0x190 [dm_persistent_data]
? kmem_cache_alloc_trace+0x15c/0x1e0
__create_persistent_data_objects+0x65/0x3e0 [dm_thin_pool]
dm_pool_metadata_open+0x8c/0xf0 [dm_thin_pool]
pool_ctr.cold.79+0x213/0x913 [dm_thin_pool]
? realloc_argv+0x50/0x70 [dm_mod]
dm_table_add_target+0x14e/0x330 [dm_mod]
table_load+0x122/0x2e0 [dm_mod]
? dev_status+0x40/0x40 [dm_mod]
ctl_ioctl+0x1aa/0x3e0 [dm_mod]
dm_ctl_ioctl+0xa/0x10 [dm_mod]
do_vfs_ioctl+0xa2/0x600
? handle_mm_fault+0xda/0x200
? __do_page_fault+0x26c/0x4f0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
2. Creating a external snapshot using the same thin-pool device.
dmsetup create thinp --table \
"0 41943040 thin-pool /dev/vdc /dev/vdb 128 0 2 ignore_discard"
dmsetup message /dev/mapper/thinp 0 "create_thin 0"
dmsetup create snap --table \
"0 204800 thin /dev/mapper/thinp 0 /dev/mapper/thinp"
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
...
Call Trace:
? __alloc_pages_nodemask+0x13c/0x2e0
retrieve_status+0xa5/0x1f0 [dm_mod]
? dm_get_live_or_inactive_table.isra.7+0x20/0x20 [dm_mod]
table_status+0x61/0xa0 [dm_mod]
ctl_ioctl+0x1aa/0x3e0 [dm_mod]
dm_ctl_ioctl+0xa/0x10 [dm_mod]
do_vfs_ioctl+0xa2/0x600
ksys_ioctl+0x60/0x90
? ksys_write+0x4f/0xb0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Jason Cai (Xiang Feng) <jason.cai@linux.alibaba.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e406f12dde upstream.
mddev->sync_thread can be set to NULL on kzalloc failure downstream.
The patch checks for such a scenario and frees allocated resources.
Committer node:
Added similar fix to raid5.c, as suggested by Guoqing.
Cc: stable@vger.kernel.org # v3.16+
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b761dcf121 upstream.
In reshape_request it already adds len to sector_nr already. It's wrong to add len to
sector_nr again after adding pages to bio. If there is bad block it can't copy one chunk
at a time, it needs to goto read_more. Now the sector_nr is wrong. It can cause data
corruption.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ae280b4ee upstream.
When provisioning a new data block for a virtual block, either because
the block was previously unallocated or because we are breaking sharing,
if the whole block of data is being overwritten the bio that triggered
the provisioning is issued immediately, skipping copying or zeroing of
the data block.
When this bio completes the new mapping is inserted in to the pool's
metadata by process_prepared_mapping(), where the bio completion is
signaled to the upper layers.
This completion is signaled without first committing the metadata. If
the bio in question has the REQ_FUA flag set and the system crashes
right after its completion and before the next metadata commit, then the
write is lost despite the REQ_FUA flag requiring that I/O completion for
this request must only be signaled after the data has been committed to
non-volatile storage.
Fix this by deferring the completion of overwrite bios, with the REQ_FUA
flag set, until after the metadata has been committed.
Cc: stable@vger.kernel.org
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d445bd9cec upstream.
Commit 00a0ea33b4 ("dm thin: do not queue freed thin mapping for next
stage processing") changed process_prepared_discard_passdown_pt1() to
increment all the blocks being discarded until after the passdown had
completed to avoid them being prematurely reused.
IO issued to a thin device that breaks sharing with a snapshot, followed
by a discard issued to snapshot(s) that previously shared the block(s),
results in passdown_double_checking_shared_status() being called to
iterate through the blocks double checking their reference count is zero
and issuing the passdown if so. So a side effect of commit 00a0ea33b4
is passdown_double_checking_shared_status() was broken.
Fix this by checking if the block reference count is greater than 1.
Also, rename dm_pool_block_is_used() to dm_pool_block_is_shared().
Fixes: 00a0ea33b4 ("dm thin: do not queue freed thin mapping for next stage processing")
Cc: stable@vger.kernel.org # 4.9+
Reported-by: ryan.p.norwood@gmail.com
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 721b1d98fb ]
kcopyd has no upper limit to the number of jobs one can allocate and
issue. Under certain workloads this can lead to excessive memory usage
and workqueue stalls. For example, when creating multiple dm-snapshot
targets with a 4K chunk size and then writing to the origin through the
page cache. Syncing the page cache causes a large number of BIOs to be
issued to the dm-snapshot origin target, which itself issues an even
larger (because of the BIO splitting taking place) number of kcopyd
jobs.
Running the following test, from the device mapper test suite [1],
dmtest run --suite snapshot -n many_snapshots_of_same_volume_N
, with 8 active snapshots, results in the kcopyd job slab cache growing
to 10G. Depending on the available system RAM this can lead to the OOM
killer killing user processes:
[463.492878] kthreadd invoked oom-killer: gfp_mask=0x6040c0(GFP_KERNEL|__GFP_COMP),
nodemask=(null), order=1, oom_score_adj=0
[463.492894] kthreadd cpuset=/ mems_allowed=0
[463.492948] CPU: 7 PID: 2 Comm: kthreadd Not tainted 4.19.0-rc7 #3
[463.492950] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
[463.492952] Call Trace:
[463.492964] dump_stack+0x7d/0xbb
[463.492973] dump_header+0x6b/0x2fc
[463.492987] ? lockdep_hardirqs_on+0xee/0x190
[463.493012] oom_kill_process+0x302/0x370
[463.493021] out_of_memory+0x113/0x560
[463.493030] __alloc_pages_slowpath+0xf40/0x1020
[463.493055] __alloc_pages_nodemask+0x348/0x3c0
[463.493067] cache_grow_begin+0x81/0x8b0
[463.493072] ? cache_grow_begin+0x874/0x8b0
[463.493078] fallback_alloc+0x1e4/0x280
[463.493092] kmem_cache_alloc_node+0xd6/0x370
[463.493098] ? copy_process.part.31+0x1c5/0x20d0
[463.493105] copy_process.part.31+0x1c5/0x20d0
[463.493115] ? __lock_acquire+0x3cc/0x1550
[463.493121] ? __switch_to_asm+0x34/0x70
[463.493129] ? kthread_create_worker_on_cpu+0x70/0x70
[463.493135] ? finish_task_switch+0x90/0x280
[463.493165] _do_fork+0xe0/0x6d0
[463.493191] ? kthreadd+0x19f/0x220
[463.493233] kernel_thread+0x25/0x30
[463.493235] kthreadd+0x1bf/0x220
[463.493242] ? kthread_create_on_cpu+0x90/0x90
[463.493248] ret_from_fork+0x3a/0x50
[463.493279] Mem-Info:
[463.493285] active_anon:20631 inactive_anon:4831 isolated_anon:0
[463.493285] active_file:80216 inactive_file:80107 isolated_file:435
[463.493285] unevictable:0 dirty:51266 writeback:109372 unstable:0
[463.493285] slab_reclaimable:31191 slab_unreclaimable:3483521
[463.493285] mapped:526 shmem:4903 pagetables:1759 bounce:0
[463.493285] free:33623 free_pcp:2392 free_cma:0
...
[463.493489] Unreclaimable slab info:
[463.493513] Name Used Total
[463.493522] bio-6 1028KB 1028KB
[463.493525] bio-5 1028KB 1028KB
[463.493528] dm_snap_pending_exception 236783KB 243789KB
[463.493531] dm_exception 41KB 42KB
[463.493534] bio-4 1216KB 1216KB
[463.493537] bio-3 439396KB 439396KB
[463.493539] kcopyd_job 6973427KB 6973427KB
...
[463.494340] Out of memory: Kill process 1298 (ruby2.3) score 1 or sacrifice child
[463.494673] Killed process 1298 (ruby2.3) total-vm:435740kB, anon-rss:20180kB, file-rss:4kB, shmem-rss:0kB
[463.506437] oom_reaper: reaped process 1298 (ruby2.3), now anon-rss:0kB, file-rss:0kB, shmem-rss:0kB
Moreover, issuing a large number of kcopyd jobs results in kcopyd
hogging the CPU, while processing them. As a result, processing of work
items, queued for execution on the same CPU as the currently running
kcopyd thread, is stalled for long periods of time, hurting performance.
Running the aforementioned test we get, in dmesg, messages like the
following:
[67501.194592] BUG: workqueue lockup - pool cpus=4 node=0 flags=0x0 nice=0 stuck for 27s!
[67501.195586] Showing busy workqueues and worker pools:
[67501.195591] workqueue events: flags=0x0
[67501.195597] pwq 8: cpus=4 node=0 flags=0x0 nice=0 active=1/256
[67501.195611] pending: cache_reap
[67501.195641] workqueue mm_percpu_wq: flags=0x8
[67501.195645] pwq 8: cpus=4 node=0 flags=0x0 nice=0 active=1/256
[67501.195656] pending: vmstat_update
[67501.195682] workqueue kblockd: flags=0x18
[67501.195687] pwq 5: cpus=2 node=0 flags=0x0 nice=-20 active=1/256
[67501.195698] pending: blk_timeout_work
[67501.195753] workqueue kcopyd: flags=0x8
[67501.195757] pwq 8: cpus=4 node=0 flags=0x0 nice=0 active=1/256
[67501.195768] pending: do_work [dm_mod]
[67501.195802] workqueue kcopyd: flags=0x8
[67501.195806] pwq 8: cpus=4 node=0 flags=0x0 nice=0 active=1/256
[67501.195817] pending: do_work [dm_mod]
[67501.195834] workqueue kcopyd: flags=0x8
[67501.195838] pwq 8: cpus=4 node=0 flags=0x0 nice=0 active=1/256
[67501.195848] pending: do_work [dm_mod]
[67501.195881] workqueue kcopyd: flags=0x8
[67501.195885] pwq 8: cpus=4 node=0 flags=0x0 nice=0 active=1/256
[67501.195896] pending: do_work [dm_mod]
[67501.195920] workqueue kcopyd: flags=0x8
[67501.195924] pwq 8: cpus=4 node=0 flags=0x0 nice=0 active=2/256
[67501.195935] in-flight: 67:do_work [dm_mod]
[67501.195945] pending: do_work [dm_mod]
[67501.195961] pool 8: cpus=4 node=0 flags=0x0 nice=0 hung=27s workers=3 idle: 129 23765
The root cause for these issues is the way dm-snapshot uses kcopyd. In
particular, the lack of an explicit or implicit limit to the maximum
number of in-flight COW jobs. The merging path is not affected because
it implicitly limits the in-flight kcopyd jobs to one.
Fix these issues by using a semaphore to limit the maximum number of
in-flight kcopyd jobs. We grab the semaphore before allocating a new
kcopyd job in start_copy() and start_full_bio() and release it after the
job finishes in copy_callback().
The initial semaphore value is configurable through a module parameter,
to allow fine tuning the maximum number of in-flight COW jobs. Setting
this parameter to zero initializes the semaphore to INT_MAX.
A default value of 2048 maximum in-flight kcopyd jobs was chosen. This
value was decided experimentally as a trade-off between memory
consumption, stalling the kernel's workqueues and maintaining a high
enough throughput.
Re-running the aforementioned test:
* Workqueue stalls are eliminated
* kcopyd's job slab cache uses a maximum of 130MB
* The time taken by the test to write to the snapshot-origin target is
reduced from 05m20.48s to 03m26.38s
[1] https://github.com/jthornber/device-mapper-test-suite
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7e6b8dfc7 ]
When using kcopyd to run callbacks through dm_kcopyd_do_callback() or
submitting copy jobs with a source size of 0, the jobs are pushed
directly to the complete_jobs list, which could be under processing by
the kcopyd thread. As a result, the kcopyd thread can continue running
completed jobs indefinitely, without releasing the CPU, as long as
someone keeps submitting new completed jobs through the aforementioned
paths. Processing of work items, queued for execution on the same CPU as
the currently running kcopyd thread, is thus stalled for excessive
amounts of time, hurting performance.
Running the following test, from the device mapper test suite [1],
dmtest run --suite snapshot -n parallel_io_to_many_snaps_N
, with 8 active snapshots, we get, in dmesg, messages like the
following:
[68899.948523] BUG: workqueue lockup - pool cpus=0 node=0 flags=0x0 nice=0 stuck for 95s!
[68899.949282] Showing busy workqueues and worker pools:
[68899.949288] workqueue events: flags=0x0
[68899.949295] pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=2/256
[68899.949306] pending: vmstat_shepherd, cache_reap
[68899.949331] workqueue mm_percpu_wq: flags=0x8
[68899.949337] pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=1/256
[68899.949345] pending: vmstat_update
[68899.949387] workqueue dm_bufio_cache: flags=0x8
[68899.949392] pwq 4: cpus=2 node=0 flags=0x0 nice=0 active=1/256
[68899.949400] pending: work_fn [dm_bufio]
[68899.949423] workqueue kcopyd: flags=0x8
[68899.949429] pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=1/256
[68899.949437] pending: do_work [dm_mod]
[68899.949452] workqueue kcopyd: flags=0x8
[68899.949458] pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=2/256
[68899.949466] in-flight: 13:do_work [dm_mod]
[68899.949474] pending: do_work [dm_mod]
[68899.949487] workqueue kcopyd: flags=0x8
[68899.949493] pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=1/256
[68899.949501] pending: do_work [dm_mod]
[68899.949515] workqueue kcopyd: flags=0x8
[68899.949521] pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=1/256
[68899.949529] pending: do_work [dm_mod]
[68899.949541] workqueue kcopyd: flags=0x8
[68899.949547] pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=1/256
[68899.949555] pending: do_work [dm_mod]
[68899.949568] pool 0: cpus=0 node=0 flags=0x0 nice=0 hung=95s workers=4 idle: 27130 27223 1084
Fix this by splitting the complete_jobs list into two parts: A user
facing part, named callback_jobs, and one used internally by kcopyd,
retaining the name complete_jobs. dm_kcopyd_do_callback() and
dispatch_job() now push their jobs to the callback_jobs list, which is
spliced to the complete_jobs list once, every time the kcopyd thread
wakes up. This prevents kcopyd from hogging the CPU indefinitely and
causing workqueue stalls.
Re-running the aforementioned test:
* Workqueue stalls are eliminated
* The maximum writing time among all targets is reduced from 09m37.10s
to 06m04.85s and the total run time of the test is reduced from
10m43.591s to 7m19.199s
[1] https://github.com/jthornber/device-mapper-test-suite
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 800a7340ab upstream.
In copy_params(), the struct 'dm_ioctl' is first copied from the user
space buffer 'user' to 'param_kernel' and the field 'data_size' is
checked against 'minimum_data_size' (size of 'struct dm_ioctl' payload
up to its 'data' member). If the check fails, an error code EINVAL will be
returned. Otherwise, param_kernel->data_size is used to do a second copy,
which copies from the same user-space buffer to 'dmi'. After the second
copy, only 'dmi->data_size' is checked against 'param_kernel->data_size'.
Given that the buffer 'user' resides in the user space, a malicious
user-space process can race to change the content in the buffer between
the two copies. This way, the attacker can inject inconsistent data
into 'dmi' (versus previously validated 'param_kernel').
Fix redundant copying of 'minimum_data_size' from user-space buffer by
using the first copy stored in 'param_kernel'. Also remove the
'data_size' check after the second copy because it is now unnecessary.
Cc: stable@vger.kernel.org
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d595567dc4 ]
If we change the number of array's device after device is removed from array,
then add the device back to array, we can see that device is added as active
role instead of spare which we expected.
Please see the below link for details:
https://marc.info/?l=linux-raid&m=153736982015076&w=2
This is caused by that we prefer to use device's previous role which is
recorded by saved_raid_disk, but we should respect the new number of
conf->raid_disks since it could be changed after device is removed.
Reported-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Tested-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d6cb6edd2 upstream.
refill->end record the last key of writeback, for example, at the first
time, keys (1,128K) to (1,1024K) are flush to the backend device, but
the end key (1,1024K) is not included, since the bellow code:
if (bkey_cmp(k, refill->end) >= 0) {
ret = MAP_DONE;
goto out;
}
And in the next time when we refill writeback keybuf again, we searched
key start from (1,1024K), and got a key bigger than it, so the key
(1,1024K) missed.
This patch modify the above code, and let the end key to be included to
the writeback key buffer.
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d07384a66 upstream.
A reload of the cache's DM table is needed during resize because
otherwise a crash will occur when attempting to access smq policy
entries associated with the portion of the cache that was recently
extended.
The reason is cache-size based data structures in the policy will not be
resized, the only way to safely extend the cache is to allow for a
proper cache policy initialization that occurs when the cache table is
loaded. For example the smq policy's space_init(), init_allocator(),
calc_hotspot_params() must be sized based on the extended cache size.
The fix for this is to disallow cache resizes of this pattern:
1) suspend "cache" target's device
2) resize the fast device used for the cache
3) resume "cache" target's device
Instead, the last step must be a full reload of the cache's DM table.
Fixes: 66a636356 ("dm cache: add stochastic-multi-queue (smq) policy")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4561ffca88 upstream.
Commit fd2fa9541 ("dm cache metadata: save in-core policy_hint_size to
on-disk superblock") enabled previously written policy hints to be
used after a cache is reactivated. But in doing so the cache
metadata's hint array was left exposed to out of bounds access because
on resize the metadata's on-disk hint array wasn't ever extended.
Fix this by ignoring that there are no on-disk hints associated with the
newly added cache blocks. An expanded on-disk hint array is later
rewritten upon the next clean shutdown of the cache.
Fixes: fd2fa9541 ("dm cache metadata: save in-core policy_hint_size to on-disk superblock")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 013ad04390 upstream.
sector_div() is only viable for use with sector_t.
dm_block_t is typedef'd to uint64_t -- so use div_u64() instead.
Fixes: 3ab918281 ("dm thin metadata: try to avoid ever aborting transactions")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ab9182816 ]
Committing a transaction can consume some metadata of it's own, we now
reserve a small amount of metadata to cover this. Free metadata
reported by the kernel will not include this reserve.
If any of the reserve has been used after a commit we enter a new
internal state PM_OUT_OF_METADATA_SPACE. This is reported as
PM_READ_ONLY, so no userland changes are needed. If the metadata
device is resized the pool will move back to PM_WRITE.
These changes mean we never need to abort and rollback a transaction due
to running out of metadata space. This is particularly important
because there have been a handful of reports of data corruption against
DM thin-provisioning that can all be attributed to the thin-pool having
ran out of metadata space.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c44a5ee803 ]
Update superblock when particular devices are requested via rebuild
(e.g. lvconvert --replace ...) to avoid spurious failure with the "New
device injected into existing raid set without 'delta_disks' or
'rebuild' parameter specified" error message.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d0ffd2642 ]
In raid10 reshape_request it gets max_sectors in read_balance. If the underlayer disks
have bad blocks, the max_sectors is less than last. It will call goto read_more many
times. It calls raise_barrier(conf, sectors_done != 0) every time. In this condition
sectors_done is not 0. So the value passed to the argument force of raise_barrier is
true.
In raise_barrier it checks conf->barrier when force is true. If force is true and
conf->barrier is 0, it panic. In this case reshape_request submits bio to under layer
disks. And in the callback function of the bio it calls lower_barrier. If the bio
finishes before calling raise_barrier again, it can trigger the BUG_ON.
Add one pair of raise_barrier/lower_barrier to fix this bug.
Signed-off-by: Xiao Ni <xni@redhat.com>
Suggested-by: Neil Brown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 010228e4a9 ]
When one node leaves cluster or stops the resyncing
(resync or recovery) array, then other nodes need to
call recover_bitmaps to continue the unfinished task.
But we need to clear suspend_area later after other
nodes copy the resync information to their bitmap
(by call bitmap_copy_from_slot). Otherwise, all nodes
could write to the suspend_area even the suspend_area
is not handled by any node, because area_resyncing
returns 0 at the beginning of raid1_write_request.
Which means one node could write suspend_area while
another node is resyncing the same area, then data
could be inconsistent.
So let's clear suspend_area later to avoid above issue
with the protection of bm lock. Also it is straightforward
to clear suspend_area after nodes have copied the resync
info to bitmap.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d63e2fc804 ]
During raid5 replacement, the stripes can be marked with R5_NeedReplace
flag. Data can be read from being-replaced devices and written to
replacing spares without reading all other devices. (It's 'replace'
mode. s.replacing = 1) If a being-replaced device is dropped, the
replacement progress will be interrupted and resumed with pure recovery
mode. However, existing stripes before being interrupted cannot read
from the dropped device anymore. It prints lots of WARN_ON messages.
And it results in data corruption because existing stripes write
problematic data into its replacement device and update the progress.
\# Erase disks (1MB + 2GB)
dd if=/dev/zero of=/dev/sda bs=1MB count=2049
dd if=/dev/zero of=/dev/sdb bs=1MB count=2049
dd if=/dev/zero of=/dev/sdc bs=1MB count=2049
dd if=/dev/zero of=/dev/sdd bs=1MB count=2049
mdadm -C /dev/md0 -amd -R -l5 -n3 -x0 /dev/sd[abc] -z 2097152
\# Ensure array stores non-zero data
dd if=/root/data_4GB.iso of=/dev/md0 bs=1MB
\# Start replacement
mdadm /dev/md0 -a /dev/sdd
mdadm /dev/md0 --replace /dev/sda
Then, Hot-plug out /dev/sda during recovery, and wait for recovery done.
echo check > /sys/block/md0/md/sync_action
cat /sys/block/md0/md/mismatch_cnt # it will be greater than 0.
Soon after you hot-plug out /dev/sda, you will see many WARN_ON
messages. The replacement recovery will be interrupted shortly. After
the recovery finishes, it will result in data corruption.
Actually, it's just an unhandled case of replacement. In commit
<f94c0b6658c7> (md/raid5: fix interaction of 'replace' and 'recovery'.),
if a NeedReplace device is not UPTODATE then that is an error, the
commit just simply print WARN_ON but also mark these corrupted stripes
with R5_WantReplace. (it means it's ready for writes.)
To fix this case, we can leverage 'sync and replace' mode mentioned in
commit <9a3e1101b827> (md/raid5: detect and handle replacements during
recovery.). We can add logics to detect and use 'sync and replace' mode
for these stripes.
Reported-by: Alex Chen <alexchen@synology.com>
Reviewed-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3943b040f1 upstream.
The writeback thread would exit with a lock held when the cache device
is detached via sysfs interface, fix it by releasing the held lock
before exiting the while-loop.
Fixes: fadd94e05c (bcache: quit dc->writeback_thread when BCACHE_DEV_DETACHING is set)
Signed-off-by: Shan Hai <shan.hai@oracle.com>
Signed-off-by: Coly Li <colyli@suse.de>
Tested-by: Shenghui Wang <shhuiw@foxmail.com>
Cc: stable@vger.kernel.org #4.17+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd2fa95416 upstream.
policy_hint_size starts as 0 during __write_initial_superblock(). It
isn't until the policy is loaded that policy_hint_size is set in-core
(cmd->policy_hint_size). But it never got recorded in the on-disk
superblock because __commit_transaction() didn't deal with transfering
the in-core cmd->policy_hint_size to the on-disk superblock.
The in-core cmd->policy_hint_size gets initialized by metadata_open()'s
__begin_transaction_flags() which re-reads all superblock fields.
Because the superblock's policy_hint_size was never properly stored, when
the cache was created, hints_array_available() would always return false
when re-activating a previously created cache. This means
__load_mappings() always considered the hints invalid and never made use
of the hints (these hints served to optimize).
Another detremental side-effect of this oversight is the cache_check
utility would fail with: "invalid hint width: 0"
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75294442d8 upstream.
Now both check_for_space() and do_no_space_timeout() will read & write
pool->pf.error_if_no_space. If these functions run concurrently, as
shown in the following case, the default setting of "queue_if_no_space"
can get lost.
precondition:
* error_if_no_space = false (aka "queue_if_no_space")
* pool is in Out-of-Data-Space (OODS) mode
* no_space_timeout worker has been queued
CPU 0: CPU 1:
// delete a thin device
process_delete_mesg()
// check_for_space() invoked by commit()
set_pool_mode(pool, PM_WRITE)
pool->pf.error_if_no_space = \
pt->requested_pf.error_if_no_space
// timeout, pool is still in OODS mode
do_no_space_timeout
// "queue_if_no_space" config is lost
pool->pf.error_if_no_space = true
pool->pf.mode = new_mode
Fix it by stopping no_space_timeout worker when switching to write mode.
Fixes: bcc696fac1 ("dm thin: stay in out-of-data-space mode once no_space_timeout expires")
Cc: stable@vger.kernel.org
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bda3153998 ]
During assemble, the spare marked for replacement is not checked.
conf->fullsync cannot be updated to be 1. As a result, recovery will
treat it as a clean array. All recovering sectors are skipped. Original
device is replaced with the not-recovered spare.
mdadm -C /dev/md0 -l10 -n4 -pn2 /dev/loop[0123]
mdadm /dev/md0 -a /dev/loop4
mdadm /dev/md0 --replace /dev/loop0
mdadm -S /dev/md0 # stop array during recovery
mdadm -A /dev/md0 /dev/loop[01234]
After reassemble, you can see recovery go on, but it completes
immediately. In fact, recovery is not actually processed.
To solve this problem, we just add the missing logics for replacment
spares. (In raid1.c or raid5.c, they have already been checked.)
Reported-by: Alex Chen <alexchen@synology.com>
Reviewed-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d12067f428 upstream.
dm_bufio_shrink_count() is called from do_shrink_slab to find out how many
freeable objects are there. The reported value doesn't have to be precise,
so we don't need to take the dm-bufio lock.
Suggested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41c73a49df upstream.
If the first allocation attempt using GFP_NOWAIT fails, drop the lock
and retry using GFP_NOIO allocation (lock is dropped because the
allocation can take some time).
Note that we won't do GFP_NOIO allocation when we loop for the second
time, because the lock shouldn't be dropped between __wait_for_free_buffer
and __get_unclaimed_buffer.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ea61cac0b upstream.
We've seen in-field reports showing _lots_ (18 in one case, 41 in
another) of tasks all sitting there blocked on:
mutex_lock+0x4c/0x68
dm_bufio_shrink_count+0x38/0x78
shrink_slab.part.54.constprop.65+0x100/0x464
shrink_zone+0xa8/0x198
In the two cases analyzed, we see one task that looks like this:
Workqueue: kverityd verity_prefetch_io
__switch_to+0x9c/0xa8
__schedule+0x440/0x6d8
schedule+0x94/0xb4
schedule_timeout+0x204/0x27c
schedule_timeout_uninterruptible+0x44/0x50
wait_iff_congested+0x9c/0x1f0
shrink_inactive_list+0x3a0/0x4cc
shrink_lruvec+0x418/0x5cc
shrink_zone+0x88/0x198
try_to_free_pages+0x51c/0x588
__alloc_pages_nodemask+0x648/0xa88
__get_free_pages+0x34/0x7c
alloc_buffer+0xa4/0x144
__bufio_new+0x84/0x278
dm_bufio_prefetch+0x9c/0x154
verity_prefetch_io+0xe8/0x10c
process_one_work+0x240/0x424
worker_thread+0x2fc/0x424
kthread+0x10c/0x114
...and that looks to be the one holding the mutex.
The problem has been reproduced on fairly easily:
0. Be running Chrome OS w/ verity enabled on the root filesystem
1. Pick test patch: http://crosreview.com/412360
2. Install launchBalloons.sh and balloon.arm from
http://crbug.com/468342
...that's just a memory stress test app.
3. On a 4GB rk3399 machine, run
nice ./launchBalloons.sh 4 900 100000
...that tries to eat 4 * 900 MB of memory and keep accessing.
4. Login to the Chrome web browser and restore many tabs
With that, I've seen printouts like:
DOUG: long bufio 90758 ms
...and stack trace always show's we're in dm_bufio_prefetch().
The problem is that we try to allocate memory with GFP_NOIO while
we're holding the dm_bufio lock. Instead we should be using
GFP_NOWAIT. Using GFP_NOIO can cause us to sleep while holding the
lock and that causes the above problems.
The current behavior explained by David Rientjes:
It will still try reclaim initially because __GFP_WAIT (or
__GFP_KSWAPD_RECLAIM) is set by GFP_NOIO. This is the cause of
contention on dm_bufio_lock() that the thread holds. You want to
pass GFP_NOWAIT instead of GFP_NOIO to alloc_buffer() when holding a
mutex that can be contended by a concurrent slab shrinker (if
count_objects didn't use a trylock, this pattern would trivially
deadlock).
This change significantly increases responsiveness of the system while
in this state. It makes a real difference because it unblocks kswapd.
In the bug report analyzed, kswapd was hung:
kswapd0 D ffffffc000204fd8 0 72 2 0x00000000
Call trace:
[<ffffffc000204fd8>] __switch_to+0x9c/0xa8
[<ffffffc00090b794>] __schedule+0x440/0x6d8
[<ffffffc00090bac0>] schedule+0x94/0xb4
[<ffffffc00090be44>] schedule_preempt_disabled+0x28/0x44
[<ffffffc00090d900>] __mutex_lock_slowpath+0x120/0x1ac
[<ffffffc00090d9d8>] mutex_lock+0x4c/0x68
[<ffffffc000708e7c>] dm_bufio_shrink_count+0x38/0x78
[<ffffffc00030b268>] shrink_slab.part.54.constprop.65+0x100/0x464
[<ffffffc00030dbd8>] shrink_zone+0xa8/0x198
[<ffffffc00030e578>] balance_pgdat+0x328/0x508
[<ffffffc00030eb7c>] kswapd+0x424/0x51c
[<ffffffc00023f06c>] kthread+0x10c/0x114
[<ffffffc000203dd0>] ret_from_fork+0x10/0x40
By unblocking kswapd memory pressure should be reduced.
Suggested-by: David Rientjes <rientjes@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a685557fbb upstream.
Discards issued to a DM thin device can complete to userspace (via
fstrim) _before_ the metadata changes associated with the discards is
reflected in the thinp superblock (e.g. free blocks). As such, if a
user constructs a test that loops repeatedly over these steps, block
allocation can fail due to discards not having completed yet:
1) fill thin device via filesystem file
2) remove file
3) fstrim
From initial report, here:
https://www.redhat.com/archives/dm-devel/2018-April/msg00022.html
"The root cause of this issue is that dm-thin will first remove
mapping and increase corresponding blocks' reference count to prevent
them from being reused before DISCARD bios get processed by the
underlying layers. However. increasing blocks' reference count could
also increase the nr_allocated_this_transaction in struct sm_disk
which makes smd->old_ll.nr_allocated +
smd->nr_allocated_this_transaction bigger than smd->old_ll.nr_blocks.
In this case, alloc_data_block() will never commit metadata to reset
the begin pointer of struct sm_disk, because sm_disk_get_nr_free()
always return an underflow value."
While there is room for improvement to the space-map accounting that
thinp is making use of: the reality is this test is inherently racey and
will result in the previous iteration's fstrim's discard(s) completing
vs concurrent block allocation, via dd, in the next iteration of the
loop.
No amount of space map accounting improvements will be able to allow
user's to use a block before a discard of that block has completed.
So the best we can really do is allow DM thinp to gracefully handle such
aggressive use of all the pool's data by degrading the pool into
out-of-data-space (OODS) mode. We _should_ get that behaviour already
(if space map accounting didn't falsely cause alloc_data_block() to
believe free space was available).. but short of that we handle the
current reality that dm_pool_alloc_data_block() can return -ENOSPC.
Reported-by: Dennis Yang <dennisyang@qnap.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 011abdc9df upstream.
If "re-add" is written to the "state" file for a device
which is faulty, this has an effect similar to removing
and re-adding the device. It should take up the
same slot in the array that it previously had, and
an accelerated (e.g. bitmap-based) rebuild should happen.
The slot that "it previously had" is determined by
rdev->saved_raid_disk.
However this is not set when a device fails (only when a device
is added), and it is cleared when resync completes.
This means that "re-add" will normally work once, but may not work a
second time.
This patch includes two fixes.
1/ when a device fails, record the ->raid_disk value in
->saved_raid_disk before clearing ->raid_disk
2/ when "re-add" is written to a device for which
->saved_raid_disk is not set, fail.
I think this is suitable for stable as it can
cause re-adding a device to be forced to do a full
resync which takes a lot longer and so puts data at
more risk.
Cc: <stable@vger.kernel.org> (v4.1)
Fixes: 97f6cd39da ("md-cluster: re-add capabilities")
Signed-off-by: NeilBrown <neilb@suse.com>
Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
