[ Upstream commit 6995a65910 ]
Fix to avoid possible memory leak if the decoder initialization
got failed.Free the allocated memory for file handle object
before return in case decoder initialization fails.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7379e6baed upstream.
The interrupt handler `pci230_interrupt()` causes a null pointer
dereference for a PCI260 card. There is no analog output subdevice for
a PCI260. The `dev->write_subdev` subdevice pointer and therefore the
`s_ao` subdevice pointer variable will be `NULL` for a PCI260. The
following call near the end of the interrupt handler results in the null
pointer dereference for a PCI260:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
Note that the other uses of `s_ao` in the calls
`pci230_handle_ao_nofifo(dev, s_ao);` and `pci230_handle_ao_fifo(dev,
s_ao);` will never be reached for a PCI260, so they are safe.
Fixes: 39064f2328 ("staging: comedi: amplc_pci230: use comedi_handle_events()")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8336be66d upstream.
The interrupt handler `dt282x_interrupt()` causes a null pointer
dereference for those supported boards that have no analog output
support. For these boards, `dev->write_subdev` will be `NULL` and
therefore the `s_ao` subdevice pointer variable will be `NULL`. In that
case, the following call near the end of the interrupt handler results
in a null pointer dereference:
comedi_handle_events(dev, s_ao);
Fix it by only calling the above function if `s_ao` is valid.
(There are other uses of `s_ao` by the interrupt handler that may or may
not be reached depending on values of hardware registers. Trust that
they are reliable for now.)
Note:
commit 4f6f009b20 ("staging: comedi: dt282x: use comedi_handle_events()")
propagates an earlier error from
commit f21c74fa4c ("staging: comedi: dt282x: use cfc_handle_events()").
Fixes: 4f6f009b20 ("staging: comedi: dt282x: use comedi_handle_events()")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df4d737ee4 ]
According to the AD7150 configuration register description, bit 7 assumes
value 1 when the threshold mode is fixed and 0 when it is adaptive,
however, the operation that identifies this mode was considering the
opposite values.
This patch renames the boolean variable to describe it correctly and
properly replaces it in the places where it is used.
Fixes: 531efd6aa0 ("staging:iio:adc:ad7150: chan_spec conv + i2c_smbus commands + drop unused poweroff timeout control.")
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ca641bae6d upstream.
The create_pagelist() "count" parameter comes from the user in
vchiq_ioctl() and it could overflow. If you look at how create_page()
is called in vchiq_prepare_bulk_data(), then the "size" variable is an
int so it doesn't make sense to allow negatives or larger than INT_MAX.
I don't know this code terribly well, but I believe that typical values
of "count" are typically quite low and I don't think this check will
affect normal valid uses at all.
The "pagelist_size" calculation can also overflow on 32 bit systems, but
not on 64 bit systems. I have added an integer overflow check for that
as well.
The Raspberry PI doesn't offer the same level of memory protection that
x86 does so these sorts of bugs are probably not super critical to fix.
Fixes: 71bad7f086 ("staging: add bcm2708 vchiq driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47830c1127 upstream.
Since moving the message buffers off the stack, the dynamically
allocated get-prop-descriptor request buffer is incorrectly sized due to
using the pointer rather than request-struct size when creating the
operation.
Fortunately, the pointer size is always larger than this one-byte
request, but this could still cause trouble on the remote end due to the
unexpected message size.
Fixes: 9d15134d06 ("greybus: power_supply: rework get descriptors")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78accaea11 upstream.
The lsb calculation is not masking the correct bits from the user input.
Subtract 1 from (1 << offset) to correctly set up the mask to be applied
to user input.
The lsb register stores its value starting at the bit 7 position.
adt7316_store_DAC() currently assumes the value is at the other end of the
register. Shift the lsb value before storing it in a new variable lsb_reg,
and write this variable to the lsb register.
Fixes: 35f6b6b86e ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45130fb030 upstream.
The calculation of the current dac value is using the wrong bits of the
dac lsb register. Create two macros to shift the lsb register value into
lsb position, depending on whether the dac is 10 or 12 bit. Initialize
data to 0 so, with an 8 bit dac, the msb register value can be bitwise
ORed with data.
Fixes: 35f6b6b86e ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10bfe7cc17 upstream.
With adt7516/7/9, internal vref is available for dacs a and b, dacs c and
d, or all dacs. The driver doesn't currently support internal vref for all
dacs. Change the else if to an if so both bits are checked rather than
just one or the other.
Signed-off-by: Jeremy Fertic <jeremyfertic@gmail.com>
Fixes: 35f6b6b86e ("staging: iio: new ADT7316/7/8 and ADT7516/7/9 driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22c971db7d ]
Colin King reported a bug in read_bbreg_hdl():
memcpy(pcmd->rsp, (u8 *)&val, pcmd->rspsz);
The problem is that "val" is uninitialized.
This code is obviously not useful, but so far as I can tell
"pcmd->cmdcode" is never GEN_CMD_CODE(_Read_BBREG) so it's not harmful
either. For now the easiest fix is to just call r8712_free_cmd_obj()
and return.
Fixes: 2865d42c78 ("staging: r8712u: Add the new driver to the mainline kernel")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
commit af4b54a2e5 upstream.
`ni6501_alloc_usb_buffers()` is called from `ni6501_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `ni6501_detach()` will be called from the core comedi
module code to clean up. `ni6501_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already beed freed, leading to a
double-free error. Fix it bu removing the call to
`kfree(devpriv->usb_rx_buf)` from `ni6501_alloc_usb_buffers()`, relying
on `ni6501_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 660cf4ce9d upstream.
If `ni6501_auto_attach()` returns an error, the core comedi module code
will call `ni6501_detach()` to clean up. If `ni6501_auto_attach()`
successfully allocated the comedi device private data, `ni6501_detach()`
assumes that a `struct mutex mut` contained in the private data has been
initialized and uses it. Unfortunately, there are a couple of places
where `ni6501_auto_attach()` can return an error after allocating the
device private data but before initializing the mutex, so this
assumption is invalid. Fix it by initializing the mutex just after
allocating the private data in `ni6501_auto_attach()` before any other
errors can be retturned. Also move the call to `usb_set_intfdata()`
just to keep the code a bit neater (either position for the call is
fine).
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=cf4f2b6c24aff0a3edf6>:
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
usb 1-1: string descriptor 0 read error: -71
comedi comedi0: Wrong number of endpoints
ni6501 1-1:0.233: driver 'ni6501' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 585 Comm: kworker/0:3 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xfe/0x12b0 kernel/locking/mutex.c:1072
ni6501_detach+0x5b/0x110 drivers/staging/comedi/drivers/ni_usb6501.c:567
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+cf4f2b6c24aff0a3edf6@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 663d294b47 upstream.
`vmk80xx_alloc_usb_buffers()` is called from `vmk80xx_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `vmk80xx_detach()` will be called from the core comedi
module code to clean up. `vmk80xx_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already been freed, leading to a
double-free error. Fix it by removing the call to
`kfree(devpriv->usb_rx_buf)` from `vmk80xx_alloc_usb_buffers()`, relying
on `vmk80xx_detach()` to free the memory.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08b7c2f920 upstream.
If `vmk80xx_auto_attach()` returns an error, the core comedi module code
will call `vmk80xx_detach()` to clean up. If `vmk80xx_auto_attach()`
successfully allocated the comedi device private data,
`vmk80xx_detach()` assumes that a `struct semaphore limit_sem` contained
in the private data has been initialized and uses it. Unfortunately,
there are a couple of places where `vmk80xx_auto_attach()` can return an
error after allocating the device private data but before initializing
the semaphore, so this assumption is invalid. Fix it by initializing
the semaphore just after allocating the private data in
`vmk80xx_auto_attach()` before any other errors can be returned.
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=54c2f58f15fe6876b6ad>:
usb 1-1: config 0 has no interface number 0
usb 1-1: New USB device found, idVendor=10cf, idProduct=8068, bcdDevice=e6.8d
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
vmk80xx 1-1:0.117: driver 'vmk80xx' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x44/0x60 kernel/locking/spinlock.c:152
down+0x12/0x80 kernel/locking/semaphore.c:58
vmk80xx_detach+0x59/0x100 drivers/staging/comedi/drivers/vmk80xx.c:829
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+54c2f58f15fe6876b6ad@syzkaller.appspotmail.com
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b9c2f2e0e upstream.
It appears on some slower systems that the driver can find its way
out of the workqueue while the interrupt is disabled by continuous polling
by it.
Move MACvIntEnable to vnt_interrupt_work so that it is always enabled
on all routes out of vnt_interrupt_process.
Move MACvIntDisable so that the device doesn't keep polling the system
while the workqueue is being processed.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
CC: stable@vger.kernel.org # v4.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc26358f89 upstream.
A check for vif is made in vnt_interrupt_work.
There is a small chance of leaving interrupt disabled while vif
is NULL and the work hasn't been scheduled.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
CC: stable@vger.kernel.org # v4.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bafd9c6405 upstream.
`ni_cdio_cmdtest()` validates Comedi asynchronous commands for the DIO
subdevice (subdevice 2) of supported National Instruments M-series
cards. It is called when handling the `COMEDI_CMD` and `COMEDI_CMDTEST`
ioctls for this subdevice. There are two causes for a possible
divide-by-zero error when validating that the `stop_arg` member of the
passed-in command is not too large.
The first cause for the divide-by-zero is that calls to
`comedi_bytes_per_scan()` are only valid once the command has been
copied to `s->async->cmd`, but that copy is only done for the
`COMEDI_CMD` ioctl. For the `COMEDI_CMDTEST` ioctl, it will use
whatever was left there by the previous `COMEDI_CMD` ioctl, if any.
(This is very likely, as it is usual for the application to use
`COMEDI_CMDTEST` before `COMEDI_CMD`.) If there has been no previous,
valid `COMEDI_CMD` for this subdevice, then `comedi_bytes_per_scan()`
will return 0, so the subsequent division in `ni_cdio_cmdtest()` of
`s->async->prealloc_bufsz / comedi_bytes_per_scan(s)` will be a
divide-by-zero error. To fix this error, call a new function
`comedi_bytes_per_scan_cmd(s, cmd)`, based on the existing
`comedi_bytes_per_scan(s)` but using a specified `struct comedi_cmd` for
its calculations. (Also refactor `comedi_bytes_per_scan()` to call the
new function.)
Once the first cause for the divide-by-zero has been fixed, the second
cause is that `comedi_bytes_per_scan_cmd()` can legitimately return 0 if
the `scan_end_arg` member of the `struct comedi_cmd` being tested is 0.
Fix it by only performing the division (and validating that `stop_arg`
is no more than the maximum value) if `comedi_bytes_per_scan_cmd()`
returns a non-zero value.
The problem was reported on the COMEDI mailing list here:
https://groups.google.com/forum/#!topic/comedi_list/4t9WlHzMhKM
Reported-by: Ivan Vasilyev <grabesstimme@gmail.com>
Tested-by: Ivan Vasilyev <grabesstimme@gmail.com>
Fixes: f164cbf98f ("staging: comedi: ni_mio_common: add finite regeneration to dio output")
Cc: <stable@vger.kernel.org> # 4.6+
Cc: Spencer E. Olson <olsonse@umich.edu>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 479826cc86 upstream.
Add missing break statement in order to prevent the code from falling
through to the default case and return -EINVAL every time.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: aa94f28888 ("staging: comedi: ni_660x: tidy up ni_660x_set_pfi_routing()")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 336650c785 ]
The ad7780 driver previously did not read the correct device output, as
it read an outdated value set at initialization. It now updates its
voltage on read.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3a3eafeef ]
Previously, ad2s90_probe ignored the return code from spi_setup, not
handling its possible failure. This patch makes ad2s90_probe check if
the code is an error code and, if so, do the following:
- Call dev_err with an appropriate error message.
- Return the spi_setup's error code.
Note: The 'return ret' statement could be out of the 'if' block, but
this whole block will be moved up in the function in the patch:
'staging:iio:ad2s90: Move device registration to the end of probe'.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0559ef7fde ]
Inside __ad7280_read32(), the spi_sync_transfer() can fail with negative
error code. This change will ensure that this error is being passed up
in the call stack, so it can be handled.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c58eef061d upstream.
Currently the cmd.read_write setting is not initialized so it contains
garbage from the stack. Fix this by setting it to 0 to indicate a
read is required.
Detected by CoverityScan, CID#1357925 ("Uninitialized scalar variable")
Fixes: c5c77ba18e ("staging: wilc1000: Add SDIO/SPI 802.11 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd29edc723 upstream.
gcc 8.1.0 generates the following warnings.
drivers/staging/speakup/kobjects.c: In function 'punc_store':
drivers/staging/speakup/kobjects.c:522:2: warning:
'strncpy' output truncated before terminating nul
copying as many bytes from a string as its length
drivers/staging/speakup/kobjects.c:504:6: note: length computed here
drivers/staging/speakup/kobjects.c: In function 'synth_store':
drivers/staging/speakup/kobjects.c:391:2: warning:
'strncpy' output truncated before terminating nul
copying as many bytes from a string as its length
drivers/staging/speakup/kobjects.c:388:8: note: length computed here
Using strncpy() is indeed less than perfect since the length of data to
be copied has already been determined with strlen(). Replace strncpy()
with memcpy() to address the warning and optimize the code a little.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 300cd66486 upstream.
In commit 8b7a13c3f4 ("staging: r8712u: Fix possible buffer
overrun") we fix a potential off by one by making the limit smaller.
The better fix is to make the buffer larger. This makes it match up
with the similar code in other drivers.
Fixes: 8b7a13c3f4 ("staging: r8712u: Fix possible buffer overrun")
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[for older kernels only, lustre has been removed from upstream]
When someone writes:
strncpy(dest, source, sizeof(source));
they really are just doing the same thing as:
strcpy(dest, source);
but somehow they feel better because they are now using the "safe"
version of the string functions. Cargo-cult programming at its
finest...
gcc-8 rightfully warns you about doing foolish things like this. Now
that the stable kernels are all starting to be built using gcc-8, let's
get rid of this warning so that we do not have to gaze at this horror.
To dropt the warning, just convert the code to using strcpy() so that if
someone really wants to audit this code and find all of the obvious
problems, it will be easier to do so.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58930cced0 upstream.
As gcc-8 points out, the bit mask check makes no sense here:
drivers/staging/rts5208/sd.c: In function 'ext_sd_send_cmd_get_rsp':
drivers/staging/rts5208/sd.c:4130:25: error: bitwise comparison always evaluates to true [-Werror=tautological-compare]
However, the code is even more bogus, as we have already
checked for the SD_RSP_TYPE_R0 case earlier in the function
and returned success. As seen in the mmc/sd driver core,
SD_RSP_TYPE_R0 means "no response" anyway, so checking for
a particular response would not help either.
This just removes the nonsensical code to get rid of the
warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e490657c7 ]
The vif->idx value is always 0 for two interfaces.
wl->vif_num = 0;
loop {
...
vif->idx = wl->vif_num;
...
wl->vif_num = i;
....
i++;
...
}
At present, vif->idx is assigned the value of wl->vif_num
at the beginning of this block and device is initialized
based on this index value.
In the next iteration, wl->vif_num is still 0 as it is only updated
later but gets assigned to vif->idx in the beginning. This causes problems
later when we try to reference a particular interface and also while
configuring the firmware.
This patch moves the assignment to vif->idx from the beginning
of the block to after wl->vif_num is updated with latest value of i.
Fixes: commit 735bb39ca3 ("staging: wilc1000: simplify vif[i]->ndev accesses")
Cc: <stable@vger.kernel.org>
Signed-off-by: Aditya Shankar <aditya.shankar@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5fae4f4fd ]
Currently the check on error return from the call to rtsx_write_register
is checking the error status from the previous call. Fix this by adding
in the missing assignment of retval.
Detected by CoverityScan, CID#709877
Fixes: fa590c222f ("staging: rts5208: add support for rts5208 and rts5288")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 498c4b4e9c upstream.
The driver may sleep under a spin lock, and the function call path is:
rtsx_exclusive_enter_ss (acquire the lock by spin_lock)
rtsx_enter_ss
rtsx_power_off_card
xd_cleanup_work
xd_delay_write
xd_finish_write
xd_copy_page
wait_timeout
schedule_timeout --> may sleep
To fix it, "wait_timeout" is replaced with mdelay in xd_copy_page.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e083926b3e ]
The PFI subdevice flags indicate that the subdevice is readable and
writeable, but that is only true for the supported "M-series" boards,
not the older "E-series" boards. Only set the SDF_READABLE and
SDF_WRITABLE subdevice flags for the M-series boards. These two flags
are mainly for informational purposes.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is against 4.9. It does not apply to master due to a large
rework of ion in 4.12 which removed the affected functions altogther.
4c23cbff07 ("staging: android: ion: Remove import interface")
Userspace can cause the kref to handles to increment
arbitrarily high. Ensure it does not overflow.
Signed-off-by: Daniel Rosenberg <drosen@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is 4.9.y only. Kernels 4.12 and later are unaffected, since
all the underlying ion_handle infrastructure has been ripped out.
The ION_IOC_{MAP,SHARE} ioctls drop and reacquire client->lock several
times while operating on one of the client's ion_handles. This creates
windows where userspace can call ION_IOC_FREE on the same client with
the same handle, and effectively make the kernel drop its own reference.
For example:
- thread A: ION_IOC_ALLOC creates an ion_handle with refcount 1
- thread A: starts ION_IOC_MAP and increments the refcount to 2
- thread B: ION_IOC_FREE decrements the refcount to 1
- thread B: ION_IOC_FREE decrements the refcount to 0 and frees the
handle
- thread A: continues ION_IOC_MAP with a dangling ion_handle * to
freed memory
Fix this by holding client->lock for the duration of
ION_IOC_{MAP,SHARE}, preventing the concurrent ION_IOC_FREE. Also
remove ion_handle_get_by_id(), since there's literally no way to use it
safely.
Cc: stable@vger.kernel.org # v4.11-
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0894da849f ]
Including asm/cacheflush.h first results in the following build error
when trying to build sparc32:allmodconfig, because 'struct page' has not
been declared, and the function declaration ends up creating a separate
(private) declaration of struct page (as a result of function arguments
being in the scope of the function declaration and definition, not in
global scope).
The C scoping rules do not just affect variable visibility, they also
affect type declaration visibility.
The end result is that when the actual call site is seen in
<linux/highmem.h>, the 'struct page' type in the caller is not the same
'struct page' that the function was declared with, resulting in:
In file included from arch/sparc/include/asm/page.h:10:0,
...
from drivers/staging/media/omap4iss/iss_video.c:15:
include/linux/highmem.h: In function 'clear_user_highpage':
include/linux/highmem.h:137:31: error:
passing argument 1 of 'sparc_flush_page_to_ram' from incompatible
pointer type
Include generic includes files first to fix the problem.
Fixes: fc96d58c10 ("[media] v4l: omap4iss: Add support for OMAP4 camera interface - Video devices")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ Added explanation of C scope rules - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45ad559a29 upstream.
Syzbot reported yet another warning with Ion:
WARNING: CPU: 0 PID: 1467 at drivers/staging/android/ion/ion.c:122
ion_buffer_destroy+0xd4/0x190 drivers/staging/android/ion/ion.c:122
Kernel panic - not syncing: panic_on_warn set ...
This is catching that a buffer was freed with an existing kernel mapping
still present. This can be easily be triggered from userspace by calling
DMA_BUF_SYNC_START without calling DMA_BUF_SYNC_END. Switch to a single
pr_warn_once to indicate the error without being disruptive.
Reported-by: syzbot+cd8bcd40cb049efa2770@syzkaller.appspotmail.com
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95a2562590 ]
On some platforms there's an ITS available but it's not enabled
because reading or writing the registers is denied by the
firmware. In fact, reading or writing them will cause the system
to reset. We could remove the node from DT in such a case, but
it's better to skip nodes that are marked as "disabled" in DT so
that we can describe the hardware that exists and use the status
property to indicate how the firmware has configured things.
Cc: Stuart Yoder <stuyoder@gmail.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17556cdbe6 ]
Commit 8f18c8a48b ("staging: lustre: lmv: separate master object
with master stripe") changed how lmo_root inodes were managed,
particularly when LMV_HASH_FLAG_MIGRATION is not set.
Previously lsm_md_oinfo[0].lmo_root was always a borrowed
inode reference and didn't need to by iput().
Since the change, that special case only applies when
LMV_HASH_FLAG_MIGRATION is set
In the upstream (lustre-release) version of this patch [Commit
60e07b972114 ("LU-4690 lod: separate master object with master
stripe")] the for loop in the lmv_unpack_md() was changed to count
from 0 and to ignore entry 0 if LMV_HASH_FLAG_MIGRATION is set.
In the patch that got applied to Linux, that change was missing,
so lsm_md_oinfo[0].lmo_root is never iput().
This results in a "VFS: Busy inodes" warning at unmount.
Fixes: 8f18c8a48b ("staging: lustre: lmv: separate master object with master stripe")
Signed-off-by: NeilBrown <neilb@suse.com>
Reviewed-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e1a7418529 ]
Currently the allocation of priv->oldaddr is not null checked which will
lead to subsequent errors when accessing priv->oldaddr. Fix this with
a null pointer check and a return of -ENOMEM on allocation failure.
Detected with Coccinelle:
drivers/staging/rtl8192u/r8192U_core.c:1708:2-15: alloc with no test,
possible model on line 1723
Fixes: 8fc8598e61 ("Staging: Added Realtek rtl8192u driver to staging")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2fab9faf9b ]
The lustre-release patch commit bdc5bb52c554 ("LU-4933 osc:
Automatically increase the max_dirty_mb") changed
- if (cli->cl_dirty + PAGE_CACHE_SIZE <= cli->cl_dirty_max &&
+ if (cli->cl_dirty_pages < cli->cl_dirty_max_pages &&
When this patch landed in Linux a couple of years later, it landed as
- if (cli->cl_dirty + PAGE_SIZE <= cli->cl_dirty_max &&
+ if (cli->cl_dirty_pages <= cli->cl_dirty_max_pages &&
which is clearly different ('<=' vs '<'), and allows cl_dirty_pages to
increase beyond cl_dirty_max_pages - which causes a latter assertion
to fails.
Fixes: 3147b26840 ("staging: lustre: osc: Automatically increase the max_dirty_mb")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
